3 ‘14/Jul INSTALLATION MANUAL CODE: 00ZMXC250/I3E DIGITAL FULL COLOR MULTIFUNCTIONAL SYSTEM MX-C250/C250E MX-C250F/C250FE MX-C250FR MX-C300F/C300W MX-C300WE/C300A MX-C300WR 3 MODEL 3 3 CONTENTS Transit, Installation (using) environment, Note [ 1 ] CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 [ 2 ] MX-C250/250E/C250F/C250FE/C250FR/C300F/C300W/C300WE C300A/C300WR(MAIN UNIT) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Machine Environment, Installation, and Transportation Service Manual 1.Machine Environment and Installation (2)Power voltage Before installing the machine, check that the following conditions are satisfied. Measure the voltage during copying to check that the voltage is in the range of the specified voltage +/- 10%. If the installing (use) conditions are not satisfied, the machine may not exhibit full performance, resulting in problems. It may also cause safety problems.
Condensation may form inside the machine causing multiple problems. Make sure machine has proper ventilation. F.Note for handling PWB and electronic parts 85% When handling the PWB and the electronic parts, be sure to observe the following precautions in order to prevent against damage by static electricity. 60% - When in transit or storing, put the parts in an anti-static bag or an anti-static case and do not touch them with bare hands.
G.Note for proper drum, developing, fusing and transfer unit handling When handling the OPC drum, developing, fusing units and transfer units, observe the following items. Drum unit - To prevent damage to the OPC drum, avoid working on the drum unit in high intensity light areas. - When the OPC drum is removed from the machine, cover it with light blocking material. (When using paper, use about 10 sheets of paper to cover it.
3 ‘14/Jul Service Manual MX-C250 [1] CONFIGURATION 1. System configuration MX-C250 MX-C250E MX-C250F/C250FE 2 MX-C250FR MX-C300E MX-C300F MX-C300W/C300WE 2 MX-C300A/C300WR Digital full color multifunctional system 500 sheet paper feed unit Sharpdesk 1 license kit Sharpdesk 5 license kit Sharpdesk 10 license kit Sharpdesk 50 license kit Sharpdesk 100 license kit 2. Product list A.
3 ‘14/Jul 3.
1 ‘13/Oct 2 ‘13/Dec 3 ‘14/Jul Service Manual [2] MX-C250/C250E/C250F/C250FE/C250FR/C300E/C300F/C300W/C300WE/ C300A/C300WR(MAIN UNIT) MX-C250 3 1.Unpacking B.Removal of the fixing tape and protection material A.Unpacking procedure 1 1) Open the top of the carton box. 2) Remove the parts included in the package. 3) Remove the main unit from the package, and remove the polyethylene bag. Place the machine on a solid, sturdy surface. * With only for north America model, remove the warning sheet.
[2] Installation 2. Installation of toner cartridges * 1. Remove the cap of developing unit 1) Remove the tray. The life of each toner cartridge is as follows: Black toner cartridge: equivalent to approximately 1K (A4/LT 5%) Color toner cartridge: equivalent to approximately 1K (A4/LT 5%) 1) Shake the toner cartridge (included in package) vertically several times. 2) Open the front cover. 2) Insert the toner cartridge horizontally and straight until it locks. 3) Remove the silica gel material.
1 ‘13/Oct C. Fusing unit lever 3) Insert the tray slowly. 4) Turn ON the machine and press the [SPECIAL FUNCTION] key on the LCD, and press the [UP] or [DOWN] key to select "Paper Size Set". 1) Open the right door unit.. 2) Turn the levers of the Fusing unit to add the pressure. 1 5. Line cable connection (Only for the machine with FAX) NOTE: When the machine is left for one month without using, the Fusing heat roller could be deformed.
1 1 ‘13/Oct 6. Specifications setting 7. Key sheet replacement (Only for north America) Use SIM26 to set to the specifications according to the customer's request. 1) Prepare the following Key sheets depending on the installed models. Machine with FAX : HPNLC0082QSZZ KEY SHEET Machine without FAX : HPNLC0082QSZ1 KEY SHEET 3IN1 SIM No 26 6 Content Destination setting 2) Remove the protector paper for the Key sheet.
3. Image quality check A. Execution items Execute the checking items about the printing quality. Regarding the specific procedures for the printing quality, refer to the Service Manual [5] ADJUSTMENT. B. Description 1. Print engine image distortion confirmation and adjustment This adjustment performs the print engine image distortion adjustment, the OPC drum phase adjustment, and the color registration adjustment simultaneously. 1) Enter SIM50-22 mode and perform the auto registration adjustment.
1 ‘13/Oct MX-C250 [3] MX-CS11 (500 SHEET PAPER FEED Service UNIT) Manual 1. Unpacking 2.Installation A. Removal of the 500 sheet paper feed unit Before execution of installation, check to confirm that the data lamp under it are not lighted or blinking. A x2 A.Turn off the power of the main unit B x2 1) Check to confirm that the operation panel is turned OFF, and then turn OFF the power switch. C x1 2) Disconnect the power plug from the power outlet. B.
1 ‘13/Oct B.Copy image position, image loss, and void area adjustment (Manual adjustment) 4) Remove the Rear cover. . 1) Place a scale on the document table as shown in the figure below. Place a scale so that it is in parallel with the scanning direction and that its lead edge is in contact with the document guide plate. Place white paper on the document table so that the scale lead edge can be seen.
1 ‘13/Oct Setting range 0 - 99 Defau lt value 30 0 - 99 20 Lead edge void area adjustment Rear edge void area adjustment FRONT/REAR void area adjustment OC document offcenter adjustment 1 - 99 40 1 - 99 35 1 - 99 35 1 - 99 DENBMFT DENBCS1 DENBCS2 SCAN sub scanning magnification ratio adjustment (CCD) Manual feed correction value Tray 1 correction value Tray 2 correction value DENBADU ADU correction value 1 Item/Display 6 Image loss area setting value Void area adjustment 7 8 9 10 11 12
Service Manual [4] Setting, Adjustments, Operation check MX-C250 1. Firmware version check and version up After installation of all the options to the machine, use SIM49-1 to check the version of each firmware. If it is not the latest version, upgrade it to the latest one. 2. Function and operation check Check that the following operations are normal.
Service Manual [5] Setup and adjustment data recording MX-C250 Print the various setup data and the adjustment data (list) with SIM22-6 and keep the data. - In case of a memory trouble, if the data is not kept, all the adjustments must be made again. - If the data is kept, the setup values and the adjustment values can be entered without adjustments, shortening the servicing time.
MX-C250 Manual [6] Necessary works before moving theService machine 1) If the following options are installed, remove all of them from the machine. 2) Remove the following consumable parts from the machine. - Paper pass unit - Paper - Toner cartridges - Development cartridge 3) Lock the following sections. - Scanner (Optical section) - Paper cassette lift plate Since the hard disk drive is built in the machine, use care not to exert vibrations or shocks to the machine when in transit.
LEAD-FREE SOLDER The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The alphabet following the LF mark shows the kind of lead-free solder. Example: Lead-Free 5mm Solder composition code (Refer to the table at the right.
CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to manufacturer’s instructions.
#/092)'(4 © "9 3(!20 #/20/2!4)/. !LL RIGHTS RESERVED 0RODUCED IN *APAN FOR ELECTRONIC $ISTRIBUTION .O PART OF THIS PUBLICATION MAY BE REPRODUCED STORED IN A RETRIEVAL SYSTEM OR TRANSMITTED IN ANY FORM OR BY ANY MEANS ELECTRONIC MECHANICAL PHOTOCOPYING RECORDING OR OTHERWISE WITHOUT PRIOR WRITTEN PERMISSION OF THE PUBLISHER 4RADEMARK ACKNOWLEDGEMENTS v -ICROSOFT¤ 7INDOWS¤ 7INDOWS¤ 7INDOWS¤ -E 7INDOWS .
