SERVICE MANUAL CODE : 00ZMXM200DS1E DIGITAL MULTIFUNCTIONAL SYSTEM MX-M160D MX-M160 MX-M200D MODEL MX-M200D MX-M200DK MX-M160D MX-M160DK MX-M160 As for the content of the MX-M200DK/MX-M160DK, refer to the content of the MX-M200D/MX-M160D as long as there is no proviso. CONTENTS [ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 [ 2 ] CONFIGURATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 [ 3 ] SPECIFICATIONS. . . . .
CONTENTS [1] GENERAL [12] FLASH ROM VERSION UP PROCEDURE 1. Note for servicing . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 [2] CONFIGURATION 1. System Configurations . . . . . . . . . . . . . . . . . . . . . . 2-1 2. Machine configuration . . . . . . . . . . . . . . . . . . . . . . . 2-1 3. Option list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 [3] SPECIFICATIONS 1. Copy mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CAUTION This product is a class 1 laser product that complies with 21CFR 1040.10 and 1040.11 of the CDRH standard and IEC60825-1 Edition 1.2-2001. This means that this machine does not produce hazardous laser radiation. The use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
[1] GENERAL •poorly ventilated 1. Note for servicing Pictogram The label ( ) in the fusing area of the machine indicates the following: : Caution, risk of danger : Caution, hot surface A. Warning for servicing •exposed to direct sunlight •The fusing area is hot. Exercise care in this area when removing misfed paper. •Do not look directly at the light source. Doing so may damage your eyes. B. Cautions for servicing •Do not switch the machine rapidly on and off.
D. Note for handling PWB and electronic parts When handling the PWB and the electronic parts, be sure to observe the following precautions in order to prevent against damage by static electricity. 1) When in transit or storing, put the parts in an anti-static bag or an anti-static case and do not touch them with bare hands. 2) When and after removing the parts from an anti-static bag (case), use an earth band as shown below: • Put an earth band to your arm, and connect it to the machine.
[2] CONFIGURATION 1. System Configurations [AR-RP10] [AR-SP10] [AR-VR7] (REVERSING SINGLE PASS FEEDER) (SINGLE PASS FEEDER) (DOCUMENT COVER) [MX-NB10] (NEWORK PRINTING / SCANNING EXPANSION KIT) Standard for North America only AR-RP10 [MX-M200D] [MX-M160] [MX-M160D] [MX-FX10] [MX-TR10] [AR-D35] (JOB SEPARATOR) [AR-D34] (2 x 250-sheet paper feed unit) (250-sheet paper feed unit) 2.
3.
[3] SPECIFICATIONS 1. Copy mode D. Document A. Type Max. document size A3, 11" X 17" Document reference position Left bottom reference Detection (Platen) Yes Type Desk-top Paper exit center tray / internal E. Paper feed B. Machine composition (1) Paper feed section details MX-M160D/MX-M160 16-CPM multi function model MX-M200D 20-CPM multi function model Item Paper capacity C. Copy speed MX-M200D MX-M160D/MX-M160 A4/ 8.5”x11” 20ppm 16ppm A4R 14ppm 12ppm 8.
J. Void width (3)Types of feedable paper Types of paper 1st tray 2nd tray Bypass tray Thin paper 56-59g/m2 15-15.9lbs Yes Yes Plain paper 60-90g/m2 16-24lbs Yes Yes Yes (Multi paper feed enable) Heavy paper 91-105g/m2 16-24lbs N/A N/A Yes (Multi paper feed enable) N/A Yes (A4 or less) (Multi paper feed enable) Void area Lead edge 1 ~ 4mm, rear edge 4mm or less, Total of both sides: 6mm or less Image loss 4.0mm or less Yes K.
M. Other specifications S. Printing function Photoconductor type OPC (Organic Photo Conductor) Photoconductor drum dia.
Item Paper SPLC Paper size A3/ A4/ A5/ A6/ B4/ B5/ B6/ Ledger/ Letter/ Legal/ Executive/ Invoice/ Foolscap/ Folio/ Com10/ DL/ C5/ 8k/ 16k/ Custom page - Custom paper: Width [100.0] -[297.0] [3.94”] -[11.69”] Length [148.0] -[431.8] [5.83”] - [17.00”] - Milimeters/ Inches Advanced setting Advanced setting T.
[4] CONSUMABLE PARTS 1.Supply system table A. USA/Canada MX-M200D No. Name Product name Content Life 1 Toner cartridge MX-206NT Toner cartridge (Toner:Net 547g With IC) x1 16K 2 Developer AR-205MD Developer (Net 300g) x10 500K (50x10) 3 Drum KIT AR-205DR Drum Drum fixing plate x1 x1 50K 19K Remark Life setting by A4 6% document B. South and Central America (200V series) MX-M160/MX-M160D/MX-M200D No.
2. Environmental conditions 3. Production number identification A. Transport conditions (1) Transport conditions The label on the toner cartridge shows the date of production. -20°C - 45°C (No condensation) (2) Storage conditions -10°C - 40°C (Unopened, No condensation) B. Use conditions Humidity (%) Production place Serial number Year/ Month/ Day Ver.No. Use environment conditions Temperature C.
[5] EXTERNAL VIEWS AND INTERNAL STRUCTURES 1. Appearance 3 7 8 9 4 1 5 5 13 10 2 14 6 12 11 15 16 17 1 USB 2.0 port Connect to your computer to this port to use the printer and scanner functions. 10 Front cover Open to remove paper misfeeds or replace the toner cartridge. 2 Charger cleaner Use to clean the transfer charger. 11 Tray 1 Tray 1 can hold approximately 250 sheets of copy paper (20 lbs. (80 g/m2 )). 3 Glass cleaner Use to clean the original scanning glass.
2. Internal 22 20 21 26 23 18 19 25 24 18 Toner cartridge lock release lever To replace the toner cartridge, pull out the toner cartridge while pushing on this lever. 27 24 28 Fusing unit release levers To remove the paper misfed in the fusing unit, push down on these levers and remove the paper. * The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or injury. 19 Toner cartridge Contains toner..
3. Operation Section 1 2 01 02 03 04 05 3 4 6 8 10 9 11 08 09 10 REDIAL/PAUSE 11 12 13 14 15 16 17 18 19 20 DEF PRINT GHI JKL MNO PQRS TUV WXYZ 14 INTERRUPT FAX STATUS COPY 07 ABC SPEAKER SHIFT 06 12 13 ON LINE DATA BACK OK SPECIAL FUNCTION SCAN SPEED SYMBOL 21 22 23 24 25 FAX LINE DATA COPY EXPOSURE SCAN COLOR MODE FAX PROGRAM COMM. SETTING @.
4. Motor, solenoid, clutch 1 2 18 3 4 5 17 6 7 8 9 10 19 11 12 4 No. 16 15 14 13 Code Name MRM Function operation 1 Mirror motor Drives the optical mirror base (scanner unit). 2 Toner motor TM 3 Duplex motor DPX Switchback operation and paper exit motor in duplex. (Only for MX-M160D/MX-M200D) 4 Cooling fan motor CFM Cools the inside of the machine. 5 Main motor MM Drives the machine.
5. Sensor, switch 23 1 2 22 24 3 18 19 20 (AB) (INCH) (AB) (INCH) 16 21 4 15 5 6 7 14 13 12 8 11 10 9 No. Name Code Function operation 1 Mirror home position sensor MHPS Detects the mirror (scanner unit) home position. 2 Side door switch DSWR Side door open detection 3 Paper exit sensor (paper exit side) POD1 Detects paper exit.
6. PWB unit 1 10 2 3 7 9 4 6 No. 5 Name Function operation 1 Copy lamp Inverter PWB Copy lamp control 2 CCD sensor PWB Image scanning 3 Main control PWB Main control PWB 4 2nd tray PWB 2nd tray control 5 High voltage PWB High voltage control 6 Power PWB AC power input/DC power control 7 Operation main PWB Operation panel input/Display, operation panel section control 9 LCD OPE PWB Display and operation panel control 10 IMC2 PWB Electronic sort, USB2.
7. Cross sectional view 1 2 3 4 5 6 7 18 8 9 10 11 12 13 14 15 23 22 21 20 19 17 No. Name 16 Function/Operation 1 Copy lamp Image radiation lamp 2 Copy lamp unit Operates in synchronization with No. 2/3 mirror unit to radiate documents sequentially. 3 LSU unit Converts image signals into laser beams to write on the drum. 4 Lens unit Reads images with the lens and the CCD. 5 MC holder unit Supplies negative charges evenly on the drum. 6 Paper exit roller Used to discharge paper.
[6]ADJUSTMENTS 1.Adjustment item list Section A B Adjustment item Process section Mechanism section Adjustment procedure/SIM No. (1) Developing doctor gap adjustment Developing doctor gap adjustment (2) MG roller main pole position adjustment MG roller main pole position adjustment (3) Developing bias voltage check (4) Main charger voltage check (1) Image position adjustment SIM-50 (2) Main scanning direction (FR direction) distortion balance adjustment No.
(3)Developing bias voltage check B.Mechanism section Note:Use a digital multi-meter with an internal resistance of 10MΩ or more. Note: If a jam error or paper empty occurs during copying in the adjustment by the simulation, the image data is not saved, and therefore recopying is required. 1) Set the digital multi-meter range above 500 Vdc. 2) Put the test rod of the digital multi-meter on the developing bias voltage output check pin. 3) Turn on the power, execute SIM25-1.
9) Measure the distance H between the paper lead edge and the image print start position. Set the image print start position set value (AUTO, 1st tray indicator ON) again. •1 step of the set value corresponds to about 0.1mm shift. •Calculate the set value from the formula below. H/0.1(mm) = Image print start position set value 0mm Adjustment mode SIM LED OC image lead edge position SIM 50-1 PHOTO R/0.
c.Rear edge void adjustment (SIM50-1, SIM50-19) 1) Set a scale as shown in the figure below. * A4(8.5" x 11") 2nd print surface (auto duplex) off-center adjustment: SIM50-10 (TEXT, 1st tray indicator) Paper rear edge Mode SIM Paper off center SIM 50-10 2nd print surface offcenter SIM 50-10 LED Set value AUTO Add 1: 0.1mm shift + Selected to R side. tray ON Reduce 1: TEXT 0.1mm shift + 1st tray to L side. Specification Single: Center ±2.
2) Loosen the copy lamp unit wire fixing screw. 4) Loosen the set screw of the scanner drive pulley which is not in contact with No. 2/3 mirror base unit positioning plate. 5) Without moving the scanner drive pulley shaft, manually turn the scanner drive pulley until the positioning plate is brought into contact with No. 2/3 mirror base unit, then fix the scanner drive pulley. Wire fixing screw 3) Manually turn the mirror base drive pulley and bring No.
(3)Main scanning direction (FR direction) distortion adjustment 4) Loosen the mirror base drive pulley fixing screw on the front frame side or on the rear frame side. This adjustment must be performed in the following cases: •When the mirror base drive wire is replaced. •When the lamp unit, or No. 2/3 mirror holder is replaced. •When a copy as shown is made. When La < Lb Turn the mirror base drive pulley on the front frame side in the arrow direction A. (Do not move the mirror base drive pulley shaft.
1) Making of a test sheet Make test sheet by drawing parallel lines at 10mm from the both ends of A3 (11" x 17") white paper as shown below. (These lines must be correctly parallel to each other.) When La < Lb Shift the mirror base B rail downward by the half of the difference of Lb - La. Example: When La = 12mm and Lb = 9mm, shift the mirror base B rail upward by 1.5mm. Parallel line Parallel line 10mm When La > Lb Shift the mirror base B rail upward by the half of the difference of La - Lb.
Note: A judgment must be made with 200mm width, and must not be made with 100mm width. Mode Main scanning direction magnification ratio Specification At normal: ±1.0% SIM Set value SIM 48-1 Add 1:0.1% increase Reduce 1: 0.1% decrease Set range 1 ~ 99 (6) Sub scanning direction (scanning direction) magnification ratio adjustment (SIM 48-1, SIM 48-5) a. OC mode in copying (SIM48-1) Note:Before performing this adjustment, be sure the CCD unit is within specification.
b. SPF original off-center adjustment (SIM50-12) C.Image density adjustment Note:Before performing this adjustment, be sure to check that the paper off center is properly adjusted. 1) Make a test chart for the center position adjustment and set it on the SPF. (1)Copy mode (SIM 46-1) Draw a line on a paper in the scanning direction. 2) Make a normal copy from the bypass tray, and compare the copy and the original test chart.
[7] SIMULATIONS 3. List of simulations 1. Entering the simulation mode Perform the following procedure to enter the simulation mode.
Main code Sub code 25 02 Contents Toner density reference control level setting (automatic development adjustment) Main code Sub code 48 01 Main/sub scanning magnification ratio adjustment 05 SPF/RSPF mode sub scanning magnification ratio adjustment in copying *2 Contents 10 Polygon motor operation check 01 Job separator setting 49 01 Flash ROM program writing mode 02 Size setting 50 01 Image lead edge adjustment 03 Auditor setting 06 Copy lead edge position adjustment (SPF/RSPF)
4. Contents of simulations Main code Sub code 01 01 Contents Mirror scanning operation Used to check the operations of the scanner unit and its control circuit. Enter the number of times and the magnification ratio, and press [OK] key to operate the scanner unit. The speed is variable according to the specified magnification ratio. The number of scanning can be specified by entering a value to the right lower section of the LCD.
Main code Sub code 02 01 Contents Remark Single Paper Feeder(SPF)/Reversing single pass feeder(RSPF)aging Used to check the operations of the SPF/RSPF unit and its control circuit. Enter the magnification ratio and press[OK] key or [START] key to drive the SPF/RSPF unit at the speed corresponding to the setting. (Magnification ratio selection window) Select the scan magnification ratio (drive speed).
Main code Sub code 02 08 Contents Remark SPF/RSPF paper feed solenoid operation check Used to drive the SPF/RSPF paper feed solenoid (PSOL) 20 times in the cycle of 500msec of "ON" and 500msec of "OFF." After completion of the process, the machine returns to the sub code input window. (Initial window) Sim2-8 SPUS CHECK (Only when the SPF/RSPF is installed.
Main code Sub code 03 03 Contents Remark Shifter operation check Japan only Used to reciprocate the shifter 4 times. During execution, the status of the shifter HP sensor is displayed on the right upper section of the screen. (When the sensor is detected, the display is highlighted.) [CA] key: Exits the simulation mode. [INTERRUPT] key: Returns to the sub code input window.
Main code Sub code 05 01 Contents Remark Operation panel display check Used to check the operations (ON, display) of the LED and the LCD on the operation panel. When this simulation is executed, all LED's on the operation panel (including 7SEG) are lighted and checking LCD is started. For the operation check of LCD, the area is divided into two sections; upper section and lower section, and the display cycle of Normal Dark Light Off is repeated in each section.
Main code Sub code 05 02 Contents Remark Fusing lamp and cooling fan operation check Used to check the operations of the heater lamp and the cooling fan and the peripheral circuits. When this simulation is executed, the following initial menu is displayed. (Initial window) Sim5-2 HT LAMP (Execution window) Sim5-2 HT LAMP [OK] key or [START] Key PRESS OK KEY EXEC EXEC When this simulation is executed, the fusing lamp repeats ON/OFF 5 times in the cycle of 500ms.
Main code Sub code 06 10 Contents Remark Main cassette pickup roller cleaning Before execution of this simulation, remove the developing cartridges. When this simulation is executed, the load select menu is displayed as shown below. Select a roller cassette to be cleaned with the numeric keys. When [OK] key or [START] key is pressed, the paper feed roller of the specified cassette is rotated halfway round and stopped with the roller facing downward.
Main code Sub code 07 08 Contents Remark Shifting with warm-up display Used to measure the warm-up time. When this simulation is executed, the following warm-up window is displayed. The time required for starting the warm-up and completing the initializing operation and shifting to the standby state is displayed. * Though [CA] key is pressed, the machine does not enter the aging mode of intermission 0 sec. (Warming up window) Sim7-8 W-UP C-MODE WARMING UP.
Main code Sub code 08 06 Contents Remark Transfer charger output When this simulation is executed, the machine shifts to the following mode select window, and the list of the modes to be outputted is displayed. Select an output mode with numeric keys and press [OK] key or [START] key, and the transfer charger output is made for about 30sec in the specified mode.
Main code Sub code 09 04 Contents Remark Duplex motor RPM adjustment Used to adjust the duplex motor rotation speed. When this simulation is executed, the following setting window is displayed. Enter an input value with numeric keys and press [OK] key or [START] key. The setting range is in 1-13 steps. (Setting window) Sim9-4 MOTOR SPEED 1:MOTOR SPEED [ 1-13] 4 4 Set value 01 02 03 04 05 06 07 08 09 10 11 12 13 (MX-M200D/MXM160D only) (Execution is not allowed when DUPLEX setting is OFF.
Main code Sub code 16 - Contents Remark U2 trouble cancel * Used to cancel the U2 trouble and execute the hard reset. When this simulation is executed, the following execution start window is displayed. Press [OK] key or [START] key to clear the U2 trouble. (Execution start window) Sim16 TROUBLE CLEAR U2 TROUBLE CLEAR AER YOU SURE? EXEC 20 01 Maintenance counter clear Used to clear the maintenance counter.
Main code Sub code 22 03 Contents Jam memory display Used to check the jam kind occurred in the main unit and the SPF/RSPF. The kinds of jams up to 30 items are displayed sequentially from the latest one. (The oldest one is deleted sequentially.) This display is used for troubleshooting. (If there are extremely many troubles in a position, it may be judged that a repair must be executed.) The kinds and contents of jams to be displayed are as follows. Sim22-3 JAM HIS.
Main code Sub code 22 13 Contents Remark CRUM destination display Used to display the CRUM chip destination code saved in the EEPROM. If the display does not match the destination code saved in the CRUM chip, it is judged as an error. * This simulation is valid only for the model with the CRUM chip. Sim22-13 CRUM CRUM TYPE nn 14 Number 00 04 05 07 08 09 99 : Setting (Destination) : Not set.
Main code Sub code 24 02 Contents Remark Trouble memory clear Used to clear the trouble memory and the trouble history data in the EEPROM. When [INTERRUPT] key is pressed, the machine shifts to the sub code input window. When [CA] key is pressed, the machine exits the simulation mode. (Only when the SPF/RSPF is installed.) Sim24-2 COUNTER CLR TROUBLE COUNTER CLEAR AER YOU SURE? EXEC 04 SPF/RSPF counter clear Used to clear the SPF/RSPF paper feed counter.
Main code Sub code 24 08 Contents Remark Copy counter clear Used to clear the copy counter. Sim24-8 COUNTER CLR COPIES COUNTER CLEAR AER YOU SURE? EXEC [OK] key or [START] key: Clears the copy counter and shifts to the sub code input window. [CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window. 09 Printer counter clear Used to clear the printer counter and other counters. Select a counter to be cleared and press [OK] key or [START] key.
Main code Sub code 25 01 Contents Remark Main motor operation check (Cooling fan motor rotation check) When [OK] key or [START] key is pressed, the main motor (as well as the duplex motor in the case of the duplex model) is rotated for 30 sec. If the developing unit is installed to save toner consumption at that time, the developing bias, the main charger, and the grid are also outputted. In addition, since laser discharge is required when the motor is stopped, the polygon motor is also operated.
Main code Sub code 25 10 Contents Remark Polygon motor operation check When [OK] key or [START] is pressed, the polygon motor is rotated for 30sec. (Execution start window) Sim25-10 LSU CHECK (Execution window) Sim25-10 LSU CHECK [OK] key or [START] Key PRESS OK KEY EXEC EXEC After completion of the process, the machine shifts to the sub code input window. [CA] key: Exits the simulation mode. [INTERRUPT] key: Interrupts the output operation, and shifts to the sub code input window.
Main code Sub code 26 04 Contents Copier duplex setting Default: 0: MX-M160 Used to set YES/NO of duplex setting. 1: MX-M160D This must be set to ON when the duplex unit is installed. If this setting is set to OFF on the duplex machine, /MX-M200D the duplex motor dose not rotate and paper is not discharged normally, resulting in a paper jam.
Main code Sub code 26 07 Contents Remark Machine condition check When this simulation is executed, the copy speed of the machine is displayed. Sim26-7 CPM CHECK 16CPM Displayed CPM list 14CPM 16CPM 20CPM [CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window. 18 Toner save mode setting Default: 0 Used to switch ON/OFF of the toner save mode. When this simulation is executed, the current set value is displayed.
Main code Sub code 26 30 Contents CE mark conformity control ON/OFF Used to set Yes/No of CE mark conformity. When this simulation is executed, the current set value is displayed. Enter a value with numeric keys and press [OK] key or [START] key. The set value is saved to EEPROM and the machine returns to the sub code input window.
Main code Sub code 26 39 Contents Remark Memory capacity check Used to check the capacity of the image memory (SDRAM) installed to the MCU PWB and the capacity of the IMC compression memory. Sim26-39 MEMORY CHK MCU : 32Mbyte IMC : 16Mbyte There are two kinds of the displayed image memory capacity: 16MB and 32MB. The standard capacity of the IMC compression memory is 16B. * It is not displayed when IMC is not installed. [CA] key: Exits the simulation mode.
Main code Sub code 26 43 Contents Remark Side void amount setting Used to set the left and right side void amounts. The left side void amount and the right side void amount can be set individually. Select an item to be changed with the arrow keys and change the set value to a desired value. The setting range is 0-10. When the value is increased by 1, the void amount is increased by 0.5mm. The default is 5 (= 2.5mm).
Main code Sub code 26 56 Contents Remark Life correction ON/OFF setting Default: 1: 0 The image correction ON/OFF setting is made according to the usage level (life) of developer. 2: 0 When this simulation is executed, the list of the modes and the current set value are displayed on the LCD. 3: 0 Select an item to be changed with the arrow keys, and change the set value to the required value.
Main code Sub code 30 01 Contents Remark Paper sensor status display Used to display the list of paper sensor status on the LCD. An active sensor is highlighted. The display items and corresponding sensors are shown below. Sim30-1 SENSOR POUT DPX PIN MBEMP C1EMP C2EMP C3EMP C4EMP C2PSS C3PSS C4PSS DRST Display POUT DPX PIN MBEMP C1EMP C2EMP C3EMP C4EMP C2PSS C3PSS C4PSS : Corresponding sensor : Paper exit sensor : DUPLEX sensor : Paper entry sensor : Manual feed paper sensor : No.
Main code Sub code 41 03 Contents Remark Document size detection photo sensor light receiving/detection level check When this simulation is executed, the light receiving level of the document detection photo sensor is displayed. (Real time display) The values in parentheses of sensor 4 and 5 are the threshold values of adjustment at SIM41-04. Since sensors 1 and 3 are not provide with the threshold value of detection at SIM41-04, "0" is always displayed.
Main code Sub code 43 12 Contents Remark Standby mode fusing fan rotation setting When this simulation is executed, the currently set code number is displayed. Select a mode to be changed with the arrow keys and enter a set value with numeric keys. Enter the mode number to be selected with numeric keys and press [OK] key or [START] key. The set value is saved in the EEPROM.
Main code Sub code 44 16 Contents Remark Toner density control data check and toner density correction quantity display The output value of the ATC sensor is checked, and the toner density control correction quantity is displayed on the LCD. Sim44-16 TONER DISP 1:TONER DEN_LT nnn 2:TONER DEN_ST nnn Name :Display content TONER DEN_LT :Current ATC sensor value TONER DEN_ST :ATC reference value with life correction quantity added [CA] key: Exits the simulation mode.
Main code Sub code 46 02 Contents Remark Copy density adjustment (600dpi) Used to set the copy density for each mode. Sim46-2 EXP. LEVEL 4:PHOTO 2 50 5:TEXT(TS) 50 6:AE(TS) 50 2/2 [ 1- 99] 50 Sim46-2 EXP.
Main code Sub code 46 09 Contents 1 1.0(SHIFT) TEXT density 1 shift amount 2 1.0(GAMMA) TEXT density 1 gamma value 3 2.0(SHIFT) TEXT density 2 shift amount 4 2.0(GAMMA) TEXT density 2 gamma value 5 3.0(SHIFT) TEXT density 3 shift amount 6 3.0(GAMMA) TEXT density 3 gamma value 7 4.0(SHIFT) TEXT density 4 shift amount 8 4.0(GAMMA) TEXT density 4 gamma value 9 5.0(SHIFT) TEXT density 5 shift amount 10 5.0(GAMMA) Remark TEXT density 5 gamma value 11 TS 1.
Main code Sub code 46 10 Contents 1 1.0(SHIFT) TEXT density 1 shift amount 2 1.0(GAMMA) TEXT density 1 gamma value 3 2.0(SHIFT) TEXT density 2 shift amount 4 2.0(GAMMA) TEXT density 2 gamma value 5 3.0(SHIFT) TEXT density 3 shift amount 6 3.0(GAMMA) TEXT density 3 gamma value 7 4.0(SHIFT) TEXT density 4 shift amount 8 4.0(GAMMA) TEXT density 4 gamma value 9 5.0(SHIFT) TEXT density 5 shift amount 10 5.0(GAMMA) Remark TEXT density 5 gamma value 11 TS 1.
Main code Sub code 46 11 Contents Remark 1 ED 1.0(SHIFT) 2 1.0(GAMMA) PHOTO (Error diffusion) density 1 shift amount PHOTO (Error diffusion) density 1 gamma value 3 ED 2.0(SHIFT) PHOTO (Error diffusion) density 2 shift amount 4 ED 2.0(GAMMA) PHOTO (Error diffusion) density 2 gamma value 5 ED 3.0(SHIFT) PHOTO (Error diffusion) density 3 shift amount 6 ED 3.0(GAMMA) PHOTO (Error diffusion) density 3 gamma value 7 ED 4.0(SHIFT) PHOTO (Error diffusion) density 4 shift amount 8 ED 4.
Main code Sub code 46 19 Contents Exposure mode setting ( Remark table setting/AE operation mode setting/Photo image process setting) Used to set the following three items. Select an item with the [ ] key or [ ] key and enter a set value with numeric keys. (1) : table setting (2) : AE operation mode (3) : PHOTO image process setting When this simulation is executed, the current set code number of the above three modes are displayed.
Main code Sub code 46 29 Contents Remark Image contrast adjustment (600dpi) Default: AE: 50 Used to adjust the image contrast for each mode. TEXT: 50 When this simulation is executed, the current set value of each mode is displayed in two digits. (Default: 50) PHOTO1: 50 PHOTO2: 50 (Adjustment item selection window) (Copy start window) (Copy execution window) TEXT (TS): 50 Sim46-29 GAMMA SET Ready to copy. Copies in progress.
Main code Sub code 46 31 Contents Remark Image sharpness adjustment Default: AE: 1 Used to adjust sharpening/shading of image for each mode. When this simulation is executed, the selection TEXT: 1 window of the adjustment items and the current set value are displayed.
Main code Sub code 48 01 Contents Remark Main/sub scanning magnification ratio adjustment Used to adjust the magnification ratio in the main scanning (front/rear) direction and the sub scanning direction. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed (Adjustment item selection window) Sim48-1 COPY MAG.
Main code Sub code 49 01 Contents Remark Flash Rom program writing mode Used to download the programs and data sections of the main unit MCU/IMC board, the FAX board, and the operation panel. When this simulation is executed, the machine immediately shifts to the download mode and the following display is shown. (When entering the download mode) (Receiving download data) Download Mode. Download Data Receiving.
Main code Sub code 49 01 Contents Remark FAX 0xFF 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x11 0x12 0x21 0x22 0x23 0x24 0x25 0x31 0x32 0x33 0x34 0x35 0x41 0x42 0x43 50 01 No process OK Download impossible Total data size error LOADER no file DWLD no file BOOT no file MAIN no file FONT download impossible Option FLASH connection error Option FLASH no match LOADER data size error LOADER work sum check error BOOT data size error BOOT work sum check error BOOT Flash erase error BOOT Flash wri
Main code Sub code 50 01 Contents Remark The adjustment value is in the range of 1 - 99. Select an adjustment item (mode) with the arrow keys, and enter the set value with numeric keys. When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy execution window. After completion of copying, the machine returns to the adjustment value input window.
Main code Sub code 50 06 Contents Remark Copy lead edge position adjustment (SPF/RSPF) Used to perform the image lead edge adjustment in the SPF/RSPF copy. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed. (Adjustment item selection window) Sim50-6 SPF EDGE 1:SIDE1 50 2:SIDE2 50 3:END EDGE 50 [ 1- 99] 50 (Only when the SPF/RSPF is installed.
Main code Sub code 50 10 Contents Remark When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy execution window. After completion of copying, the machine returns to the adjustment value input window. When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and performs copying. (Copy start window) Ready to copy.
Main code Sub code 50 18 Contents Remark Memory reverse position adjustment in duplex copy Used to adjust the reverse point (scanning end position) on the reversed surface in duplex copy. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed (Adjustment item selection window) Display text array : Adjustment mode Sim50-18 DUP REV.
Main code Sub code 50 19 Contents Remark Rear edge void adjustment in duplex copy Used to adjust the rear edge void amount in duplex copy. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed.
Main code Sub code 51 02 Contents Remark (*1) Valid only when an option is installed. (If an option is not installed, it is not displayed on the adjustment window.) (*2) When heavy paper slips in manual feed copy, or when a paper jam occurs in thin paper copy, adjust this set value to remove the problem. •Heavy paper slips. • Thin paper jams. Increase the set value. Decrease the set value. The adjustment range is 1 - 99.
Main code Sub code 53 10 Contents Remark SPF/RSPF scanning position setting Default: 1 Used to change setting depending on whether the SPF/RSPF unit and the SPF/RSPF document glass holder section are anti-dirt glass or not. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed.
Main code Sub code 63 07 Contents SPF/RSPF automatic correction Used to adjust the SPF/RSPF white correction start pixel position. When the carriage or the platen glass is replace, this simulation must be executed. When this simulation is executed, the initial window as shown below is displayed.
Main code Sub code 65 10 Contents Key reception time setting display/non-display setting Remark Default: 1 Used to set Enable/Disable of the key reception time setting in the system settings. When this setting is set to Enable (1), the key reception time is displayed in the system settings, allowing setting. Sim65-10 KEY TIME 1:KEY ACK TIME 1 [ 0- 1] Display: Setting 0: Disable 1: Enable 1 [CA] key: Exit the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.
[8] SYSTEM SETTINGS The user programs allow the parameters of certain functions to be set, changed, or canceled as desired. 1. List of user programs This copier has the following user programs.
2. Using the system settings 1) Press the [SPECIAL FUNCTION] key. ON LINE DATA SPECIAL FUNCTION LINE DATA COPY EXPOSURE PAPE SCAN COLOR MODE RESOLUT 6) Press the [OK] key. SPECIAL FUNCTION SPECIAL MODES ORIG. SIZE ENTER PAPER SIZE SET DISPLAY CONTRAST The special function screen will appear. 2) Select "SYSTEM SETTINGS" with the [ PQ UPLEX LEX SCAN LEX SCAN ACC OK ] key.
[9] TROUBLE CODE LIST 2. Details of trouble codes Main Sub code code E1 00 Content Detail 1.
Main Sub code code E1 82 Content Detail Cause 84 Check and remedy Content Detail Cause E7 01 Check and remedy Content Detail Cause 02 Check and remedy Content Detail Cause Check and remedy 10 Content Detail Cause Check and remedy Details of trouble Interface error in communication with IMC PWB (Overrun). An overrun error occurs in communication between the MCU PWB and the IMC PWB. IMC PWB-MCU PWB harness defect. Improper connection of the MCU PWB connector. IMC PWB ROM defect/data abnormality.
Main Sub code code F2 04 Content Detail Cause Check and remedy Identificat ion error Model error Type error Destinatio n error Data abnormali ty 40 F5 F6 02 00 10 Details of trouble Improper cartridge (destination error, life cycle error) The destination of the machine differs from that of the CRUM. The life cycle information is other than "Not used (FFh)". CRUM chip defect. Improper developing unit . Replace the CRUM chip. Replace the developing unit. The trade mark code of the CRUM differs.
Main Sub code code H2 00 Content Detail Cause H3 00 Check and remedy Content Detail Cause Check and remedy H4 00 Content Detail Cause Check and remedy H5 01 Content Detail Cause Check and remedy Details of trouble Thermistor open. The thermistor is open. The fusing unit is not installed. Thermistor abnormality. Control PWB abnormality. Fusing section connector disconnection. The fusing unit is not installed. Check the harness and the connector between the thermistor and the PWB.
Main Sub code code L6 10 Content Detail Cause Check and remedy L8 01 Content Detail Cause Check and remedy U1 U2 03 04 11 40 Content Detail Cause Check and remedy Content Detail Cause Check and remedy Content Detail Cause Check and remedy Content Detail Cause Check and remedy Details of trouble Polygon motor lock detection. The polygon motor does not rotate. The motor lock signal is detected for 6sec after rotation of the polygon motor.
[10] MAINTENANCE 1. Maintenance table Unit name Drum peripheral Part name X:Check(Clean, adjust, or replace when required.
2. Maintenance display system Toner Life, Remaining quantity check *1 Remaining quantity Developer C. DV seal attachment procedure 16K a. Press and hold the [Light] keys ([Light and Dark] keys) for more than 5 sec, and the machine will enter the user program mode. b. Press and hold the [%] key for more than 5 sec, and the remaining quantity will be displayed on the copy quantity display in one of the following levels: (Remaining quantity display levels: 100%, 75%, 50%, 25%, 10%, LO) c.
[11]DISASSEMBLY AND ASSEMBLY B.Charger wire WARNING Before performing the disassembly procedure, be sure to remove the power cord to prevent against an electric shock. Installation: The spring tip must be between two reference ribs. •The charger wire must be free from twists or bending. •Be sure to put the charger wire in the V groove. No.
2.Optical section C.Inverter PWB for copy lamp (1) Note: When disassembling or assembling the optical unit, be careful not to touch the mirror and the reflector. No. Content A Table glass B Copy lamp unit C Inverter PWB for copy lamp D Copy lamp E Lens unit F Wire G Document detection (2) (1) A.Table glass (1) (2) (1) (1) (3) (4) (1) (3) (3) B.Copy lamp unit Disassembly: Assembly: Adjustment: Be sure to put No. 2/3 mirror unit to the positioning plate (A).
E.Lens unit F.Wire Note:Do not remove screws which are not indicated in the figure. If the height of the base plate is changed, it cannot be adjusted in the market. Note:The CCD/lens unit is factory-adjusted before shipping. Since these adjustments cannot be performed in the market. Never touch the screws other than screw 2) of the CCD/lens unit.
B.Thermostat • For AB series (2) (2) (3) (1) (3) (1) (1) (4) (2) (2) (3) (2) 3.Fusing section No. Contents A Fusing unit B Thermostat C Thermistor D Heater lamp E Upper heat roller F Separation pawl G Lower heat roller H Separation pawl C.Thermistor Installation: Install in direction that the sponge side (A) of the thermistor comes in contact with heat roller. Check that the thermistor is in contact with the upper heat roller. A.
D.Heater lamp E.Upper heat roller Assembly: Insert the spring (A) into the hole (B) in the fusing frame. Disassembly: There are three pawls on the fusing cover. Remove the screws and slide the fusing cover to the right to remove. The heater lamp is fixed on the fusing cover with a screw. Slide the fusing cover to the front and remove the screw, then remove the heater lamp.
F.Separation pawl H.Separation pawl (1) (2) (3) (2) (3) 4.Paper exit section No. G.Lower heat roller Assembly: When assembling the fusing front paper guide (3), temporarily fix the paper guide fixing plate with the screw so that the paper guide fixing plate (2) is in contact with the fusing lower frame bottom (A). For Taiwan: Align the edge (B) of the fusing front paper guide (3) and the top (C) of the rib on a line, and tighten the screw firmly.
B.Cooling fan MX-M160D/M200D (1) (2) (3) (2) (2) (2) (3) (3) (2) (3) MX-M160 C.Paper exit unit (2) (3) (2) (1) (1) (2) (3) (3) (5) (2) (4) (6) (2) (1) (4) (5) (2) (1) (2) (1) D.
E.Transport roller G.Paper exit interface PWB (1) (1) (2) (2) (1) (1) (3) (3) (3) (4) (5) (4) (1) (1) (1) (2) (3) (3) (1) (2) (3) F.Paper exit roller Assembly: 5.MCU Insert the spring pin so that the waveform (A) of the spring pin faces in the longitudinal direction of the paper exit drive gear long hole (B). Be sure to insert two ribs (C) into the groove (D). No. A Content MCU A.
6.Optical frame unit No. A (1) Content (2) Optical frame unit (2) (3) A.Optical frame unit Installation: Install the optical unit in the sequence shown above. (2) (1) Note:Do not disassemble the LSU. Note:When replacing the LSU, be careful not to touch the dust-shield glass. (1) (1) (1) (1) (1) (1) 8. Tray paper feed section/Paper transport section 7. LSU No. No.
Assembly: C. Solenoid (paper feed solenoid, resist roller solenoid) Do not miss the door lock pawl. (1) (1) (2) (3) (1) (2) (2) (1) D. Resist roller clutch/Resist roller Apply grease (FG-40H) to the gray area (UKOG-0004QSZZ). B. Drive unit Assembly: Move down the clutch pawl as shown below, and avoid the clutch and install. (1) (2) (1) (2) (3) (3) (3) (4) E. Paper feed clutch/Paper feed roller (1) (2) Moricote X56020 Apply grease (FG-40H) to the gray area (UKOG-0004QSZZ).
9.Bypass tray section No. B. Bypass tray paper feed Content A Bypass tray transport roller/Bypass tray paper feed roller B Bypass tray paper feed C Bypass tray solenoid D Bypass tray transport clutch E Pressure plate unit F Bypass tray paper feed clutch (1) (3) A. Bypass tray transport roller/Bypass tray paper feed roller (4) (2) Note:Push the lever at the right edge of the multi frame cover to the right upper side and remove it. A (5) (2) A A A A (3) (4) A (1) C.
D. Bypass tray transport clutch F. Bypass tray paper feed clutch Note: Push the lever at the right edge of the multi frame cover to the right upper side and remove it. (1) (2) (1) (2) A A (5) (3) A (1) (4) (1) (3) Apply grease (FG-40H) to the gray area (UKOG-0004QSZZ). Apply grease (FG-40H) (UKOG-0004QSZZ). (2) E.Pressure plate unit (2) (2) (2) (2) (3) (3) (1) (4) (1) Apply grease (FG-40H) to the gray area (UKOG-0004QSZZ).
10.Power section C. High voltage P.W.B. No. Content A Power unit B Power fan C High voltage P.W.B. D Power P.W.B. E Power switch (1) (2) A.Power unit (1) (1) (1) (2) D. Power P.W.B. (1) (1) (2) (1) (2) (2) (2) (2) (3) (2) (2) (3) (2) (2) (1) (2) (1) B. Power fan E.
11.Developing section No. C.MG roller Contents A Developing box B Developing doctor C MG roller A.Developing box (1) (5) (4) (3) (2) (3) B.Developing doctor (3) (3) (4) (1) (3) (2) Adjustment: Developing doctor gap adjustment Adjustment: MG roller main pole position adjustment Note:Attach it to fit with the attachment reference when replacing the DV blade. Mark-off line Attaching reference 0 0.5 DV blade 0.
12.Process section No. 13.Others Contents A Drum unit B C No. Contents A Operation P.W.B. Main charger unit B Tray interface P.W.B. Cleaning blade C 2nd tray paper entry sensor / Paper empty sensor D 2nd tray paper feed solenoid / Transport solenoid E 2nd tray transport clutch F 2nd tray transport roller G 2nd tray paper feed clutch H 2nd tray paper feed roller I Main motor J I/F P.W.B. K Paper entry sensor L Paper empty sensor M Paper feed roller A.
B. Tray interface P.W.B. (1) (3) (2) (3) (3) (1) (1) (1) (2) (1) (2) (1) (1) (1) (1) (1) (2) (2) (3) (1) positioning pin C. 2nd tray paper entry sensor / Paper empty sensor hole (4) (1) [Note for installation] When installing, engage the hole of the LCD box unit with the positioning pin.
D. 2nd tray paper feed solenoid / Transport solenoid G. 2nd tray paper feed clutch (2) (2) A (2) (1) (1) (1) (3) E.2nd tray transport clutch Apply grease (FG-40H) to the gray area (UKOG-0004QSZZ). H. 2nd tray paper feed roller (2) (1 Apply grease (FG-40H) to the gray area (UKOG-0004QSZZ). (1) F.
I. Main motor K. Paper empty sensor (2) (3) (2) (1) (1) L. Paper feed roller (1) (3) (2) J. Paper entry sensor (1) (2) * When removing the paper feed roller, operate the paper feed clutch with SIM 6-1, and keep the paper feed roller down as shown in the figure above for operation.
[12]FLASH ROM VERSION UP PROCEDURE 1.Preparation Items to be prepared • Utility tool • USB driver • PC • USB cable • Data file of Firmware The utility tool and USB driver are included to Maintenance_toolV****.zip. (**** = Version no.) 4) Select "Include this location in the serch". If the retrieval area does not include the folder which includes the maintenance tool driver (Mainte.inf), select "Browse" If the folder path is properly shown, press the NEXT button to go to procedure 7).
8) When installation is completed, the following display is shown. Press the Finish button. 4) PC side: Confirm that the "Simulation Command List" tree is displayed on the maintenance program. 5) PC side: When the message "the main body has not got started running" is displayed on the lowest area of the figure below after the "maintenance program" is started up, select the "File" and then "Reconnect" in the menu bar. The installation procedure is completed with the above operation. 3.
8) PC side: Specify the download file (*.dwl). from the above 5). * Forbidden actions while downloading (Important) 9) PC side: The download file is specified, download is automatically performed. The AUTO PAPER SELECT indicator and START indicator will blink approximately 15 seconds after the download file is specified. 10) PC side: When the message below is displayed, download is completed.
/MMD MX-M200D ELECTRICAL SECTION 13-1 sch buf COIN VENDOR/AUDITOR /CV_COPY /CV_COUNT,/CV_START,/CV_CA, /CV_DPX,/CV_SIZE0,1,2,3 CPU INTERRUPT SPPD CPU I/O RTH DRST Toner Motor Mirror Motor Driver Polygon Moter /VIDEO S/H APCSTT Driver LSU /SYNC Other Inputs MainMotor /MMRDY MPFS, RRS, SGS, SRRC, SPUS, SPPS, VFMCNT, VFM, MPFS, CPFS2, CPFS1 TM+, TM Driver MHPS HOME POSITION SENSOR Reset IC D[15...
6 3 3 3 3 MX-M200D ELECTRICAL SECTION 13-2 VLR-02V HL HARNESS DEV HARNESS CRUM-MCU HARNESS HAND SOLENOID HARNESS PICK UP SOL HANDEMP harness GP1S58 B4B-PH dehumidifying heater (Red) (PWB PWB pattern only) P-IN HARNESS GP1S73 PAP-02V-S PALR-02V 3 B26B-PUDSS-1 (White) AUDITOR OPTION OPTION COIN VENDER Cassette dehumidifying heater Only for Japan PS HARNESS 1st TRAY OR 2nd TRAY OR VLR-02V MULTI CASSETTE 26 LSU-MCU HARNESS B02P-NV MC GRID MCFB USB2.
NEW MX-M200D ELECTRICAL SECTION 13-3 CASSETTE SWITCH CASSETTE EMPTY SENSOR PAPER IN SENSOR 175767-3 3 1 2 1 2 3 (DRUM) DGND D2X D2X (CASETTE) DGND GP1S73 15778-2 1 2 15778-2 1 2 175767-3 3 5Vp-off 1 (CPEMPTY) 2 DGND GP1S73 5Vp-off (PIN) DGND GP1S58 5Vp-off (HPEMPTY) DGND 06FE-BT-VK-N 8 PGND 7 PGND 6 /MMRDY 5 /MMD 4 N.C.
< CCDMCU FFC > CN5 (FF4-32-S15D3-FA) 32 DGND 31 MODE 30 AFE_DB0 29 AFE_DB1 28 AFE_DB2 27 AFE_DB3 26 AFE_DB4 25 AFE_DB5 24 AFE_DB6 23 AFE_DB7 22 AFE_SCK 21 DGND 20 ADCLK 19 AFE_SEN 18 CCD_PHI1 17 DGND 16 CCD_PHI2 15 AFE_SDI 14 CCD_CP 13 BSAMP 12 CCD_RS 11 DGND 10 CCD_TG 9 VSAMP 8 DGND 7 3.
MX-M200D ELECTRICAL SECTION 13-5 CN25 (B3B-PH-K-S) 1 RTH_IN 2 N.C.
MX-M200D ELECTRICAL SECTION 13-6 CN1(9610S-16C) SCAN9 SCAN5 SCAN8 SCAN7 SENSE6 SCAN6 SENSE4 SENSE5 SCAN4 SCAN3 SCAN2 SCAN1 SCAN0 /FAXSW /FAXOPD DGND FAX-KEY PWB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CN1(9610S-28C) DGND 1 2 H_LED 3 LED2 4 ST_LED 5 SCAN8 6 SCAN1 7 SCAN2 8 SCAN5 9 SCAN3 10 ST_KEY 11 SENSE3 12 SENSE2 13 SCAN6 14 SCAN4 15 SCAN7 16 SENSE1 17 SENSE0 18 SCAN0 19 LED5 20 LED4 21 LED3 22 LEDSI 23 LEDCLK 24 /LEDLATCH 25 /LEDENABLE 26 LED1 27 3.
MX-M200D ELECTRICAL SECTION 13-7 CN003(B02P-XL) LIVE NEUTRAL PS PWB (3/3) 1 2 WH BK < DH PS HARNESS > 1 2 3 9 4 19 17 21 5 6 7 8 11 10 22 20 12 18 13 15 14 16 DH-L B (172074-1) White (172074-7) Red B LIVE dehumidifying heater SW N.C. N.C.
1 2 3 1 2 3 D-GND DRS1 5V D-GND CSS1 5V DRS1 CSS1 1 2 3 1 2 3 D-GND DRS1 5V D-GND CSS1 5V DRS1 CSS1 < 2-stage cassette harness > < 1-stage cassette harness > 3 4 5 6 7 8 1 2 3 1 2 3 CASS2 D-GND D-GND PPD2 5V D-GND CSS2 5V CASS2 PPD2 CSS2 D-GND CSS2 5V D-GND PPD2 5V 6 7 8 3 4 5 SMR-08V-N SMP-08V-NC 1 1 CASS2 2 2 D-GND DF3-3S-2C DF3-3S-2C DF3-3S-2C 175778-2 < Multi-stage harness2 > 1 2 1 2 3 D-GND PPD1 5V PPD1 LOWER UNIT 1 2 CASS1 D-GND SMR-02V-B SMP-02V-BC 1 1 24V 2 2 /F
3.
Category Signal name Sensor OCCOVER Operation panel Operation panel /PANEL_RST Dehumidifying Solenoid /DHROFF Solenoid Solenoid Solenoid SPFGSOL SPFPSOL /HPSOL Solenoid Solenoid /PSRSOL /CPSOL Solenoid (PSOL1) Solenoid (FSOL1) Solenoid (PSOL2) Solenoid (FSOL2) Solenoid (PSOL3) Solenoid (FSOL3) Power supply Power supply Power supply Power supply Power supply Power supply control Power supply control Power supply control Power supply control Fan 3.
Category Signal name Motor /PMCLK Motor Motor (SPMT0) (SPMT1) (SPMT2) (SPMT3) OUT_A+ OUT_B+ OUT_AOUT_B/DMT_0 /DMT_1 /DMT_2 /DMT_3 /MMD Motor /MMRDY Motor TMA_O TMB_O (JOBS_MT0) (JOBS_MT1) (JOBS_MT2) (JOBS_MT3) (SJMT0) (SJMT1) (SJMT2) (SJMT3) Motor Motor Motor Motor Name(Type) Function/Operation Connector level "L" "H" — — Connector No. CN703 Pin No.
LEAD-FREE SOLDER The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The alphabet following the LF mark shows the kind of lead-free solder. Example: Lead-Free 5mm Solder composition code (Refer to the table at the right.
CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to manufacturer’s instructions.
COPYRIGHT © 2009 BY SHARP CORPORATION All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic; mechanical; photocopying; recording or otherwise without prior written permission of the publisher. Trademark acknowledgements Microsoft ® Windows ® operating system is a trademark or copyright of Microsoft Corporation in the U. S. A. and other countries.
