Installation manual

ManualsBrandsSharp ManualsOtherMX-M453U

INSTALLATION MANUAL

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with

specified ones for maintaining the safety and performance of the set.

This document has been published to be used

for after sales service only.

The contents are subject to change without notice.

SHARP CORPORATION

CONTENTS

CODE: 00ZMXM503/I3E

DIGITAL MULTIFUNCTIONAL SYSTEM

MODEL

: '10/Jun/18

MX-M283N

MX-M363N/U

MX-M453N/U

MX-M503N/U

MX-M282N/M362N

MX-M452N/M502N

CONFIGURATION

[1] MX-M283N/M363N/M363U/

M453N/M453U/M503N/M503U/

M282N/M362N/M452N/M502N . . . . 1-1

[2] MX-DEX8/DEX9 . . . . . . . . . . . . . . . . 2-1

[3] MX-LCX1 . . . . . . . . . . . . . . . . . . . . . 3-1

[4] MX-FNX9 . . . . . . . . . . . . . . . . . . . . . 4-1

[5] MX-PNX1 . . . . . . . . . . . . . . . . . . . . . 5-1

[6] MX-RBX3 . . . . . . . . . . . . . . . . . . . . . 6-1

[7] MX-FN10 . . . . . . . . . . . . . . . . . . . . . 7-1

[8] MX-PNX5A/B/C/D . . . . . . . . . . . . . . 8-1

[9] MX-FN11 . . . . . . . . . . . . . . . . . . . . . 9-1

[10] MX-PNX6A/B/C/D . . . . . . . . . . . . . 10-1

[11] MX-TRX2 . . . . . . . . . . . . . . . . . . . . 11-1

[12] MX-FXX2 . . . . . . . . . . . . . . . . . . . . 12-1

[13] AR-SU1 . . . . . . . . . . . . . . . . . . . . . 13-1

[14] MX-PB10 . . . . . . . . . . . . . . . . . . . . 14-1

[15] MX-PB11 . . . . . . . . . . . . . . . . . . . . 15-1

[16] MX-FWX1. . . . . . . . . . . . . . . . . . . . 16-1

[17] MX-EBX3 . . . . . . . . . . . . . . . . . . . . 17-1

[18] MX-PKX1 . . . . . . . . . . . . . . . . . . . . 18-1

[19] MX-PUX1 . . . . . . . . . . . . . . . . . . . . 19-1

[20] MX-SMX3. . . . . . . . . . . . . . . . . . . . 20-1

[21] AR-PF1 . . . . . . . . . . . . . . . . . . . . . 21-1

[22] MX-FR14U/FR14/FR15U/FR15/

FR24U . . . . . . . . . . . . . . . . . . . . . . 22-1

[23] MX-KBX2 . . . . . . . . . . . . . . . . . . . . 23-1

[24] MX-AMX1. . . . . . . . . . . . . . . . . . . . 24-1

[25] MX-AMX2. . . . . . . . . . . . . . . . . . . . 25-1

[26] MX-AMX3. . . . . . . . . . . . . . . . . . . . 26-1

[27] Dehumidifying heater . . . . . . . . . . . 27-1

[28] MX-RP11 . . . . . . . . . . . . . . . . . . . . 28-1

[29] MX-PC11/XB13

Refer to the MX-PC11

(00ZMXPC11/A1J) service manual

Summary of content (117 pages)

PAGE 1
: '10/Jun/18 INSTALLATION MANUAL CODE: 00ZMXM503/I3E DIGITAL MULTIFUNCTIONAL SYSTEM MX-M283N MX-M363N/U MX-M453N/U MX-M503N/U MX-M282N/M362N MODEL MX-M452N/M502N 1 CONTENTS CONFIGURATION [16] MX-FWX1. . . . . . . . . . . . . . . . . . . . 16-1 [1] MX-M283N/M363N/M363U/ M453N/M453U/M503N/M503U/ M282N/M362N/M452N/M502N . . . . 1-1 [17] MX-EBX3 . . . . . . . . . . . . . . . . . . . . 17-1 [2] MX-DEX8/DEX9 . . . . . . . . . . . . . . . . 2-1 [19] MX-PUX1 . . . . . . . . . . . . . . . . . . . .
PAGE 2
1 : '10/Jun/18 CONTENTS CONFIGURATION 1. Main unit and option. . . . . . . . . . . . . . . . . . . . . . .i 2. Main unit configuration. . . . . . . . . . . . . . . . . . . . ii 3. Combination of options . . . . . . . . . . . . . . . . . . . ii [1] 1 MX-M283N/M363N/M363U/M453N/M453U/M503N/ M503U/M282N/M362N/M452N/M502N 1. Installing (use) conditions . . . . . . . . . . . . . . . 1-1 2. Transit and delivery . . . . . . . . . . . . . . . . . . . . 1-3 3. Unpacking . . . . . . . . . . . . . . . . . . . . .
PAGE 3
1 : '10/Jun/18 CONFIGURATION MX-M503N Service Manual 1.
PAGE 4
1 : '10/Jun/18 1 Printer expansion PRINTER EXPANSION KIT WITHOUT HDD (For U model only) 17 MX-PB10 Image send expansion PRINTER EXPANSION KIT WITH HDD (For U model only) 18 MX-PB11 PS3 EXPANSION KIT 19 MX-PKX1 FACSIMILE EXPANSION KIT BARCODE FONT KIT 21 AR-PF1 XPS EXPANSION KIT 20 MX-PUX1 30 MX-FR14 DATA SECURITY KIT (For the machine without HDD installed) DATA SECURITY KIT (For the machine without HDD installed) 32 MX-FR15 31 MX-FR15U STAMP CARTRIDGE 26 MX-EBX3 APPLICATION INTEGRATIO
PAGE 5
1 1 : '10/Jun/18 Paper exit system Printer expansion Image send expansion Authentication/ Security { { { { { { { { { { { { { { { { MX-PB10 MX-PB11 MX-PKX1 MX-PUX1 — STD { {*3 { { { {*3 — STD { {*3 { { { { BARCODE FONT KIT FACSIMILE EXPANSION KIT STAMP UNIT STAMP CARTRIDGE INTERNET FAX EXPANSION KIT ENHANCED COMPRESSION KIT APPLICATION INTEGRATION MODULE NETWORK SCANNER EXPANSION KIT DATA SECURITY KIT (For the machine with HDD installed) DATA SECURITY KIT (For the machine with HDD insta
PAGE 6
1 : '10/Jun/18 [1] MX-M283N/M363N/M363U/ M453N/M453U/M503N/M503U/ M282N/M362N/M452N/M502N MX-M503N 1 (3) Power Manual frequency, waveform Service The frequency must be within the range of the specified frequency ±2%. If power waveform is deformed, a trouble may occur. (4) Safety Be sure to properly ground the machine. 1. Installing (use) conditions Before installing the machine, check that the following installing (use) conditions are satisfied.
PAGE 7
(2) Dust F. Note for handling PWB and electronic parts If dust enters the machine, it may cause dirty copy and a paper jam, resulting in a shortened lifetime. (3) When handling the PWB and the electronic parts, be sure to observe the following precautions in order to prevent against damage by static electricity. 1) When in transit or storing, put the parts in an anti-static bag or an anti-static case and do not touch them with bare hands.
PAGE 8
1 : '10/Jun/18 G. Note for handling the drum unit, the transfer unit, the developing unit, and the fusing unit When handling the OPC drum unit, the transfer unit, and the developing unit, strictly observe the following items. If these items are neglected, a trouble may be generated in the copy and print image quality. 3. Unpacking A. Unpacking procedure 1) Remove the PP band. 2) Remove the internal packing pads with the machine. (Drum unit) 1) Avoid working at a place with strong lights.
PAGE 9
: '10/Jun/18 1 4. • MX-M282N/M362N/M452N/M502N 1 Installation * When connecting the main unit with the optional STAND/1 X 500 SHEET PAPER DRAWER (MX-DEX8) or STAND/2 X 500 SHEET PAPER DRAWER (MX-DEX9), first unpack and install the MX-DEX8 or MX-DEX9; then unpack the main unit and securely place the main unit on the MX-DEX8 or MX-DEX9 before installing the main unit. A.
PAGE 10
1 (3) : '10/Jun/18 Removal of the fusing heat roller protector B. Developer supply Be careful not to put fingerprints or oil dirt on the roller surface. Do not hold the case adjacent to the DV roller strongly. 1 (4) Install the paper exit cover unit 1) Open the front cabinet, and remove the waste toner box. 2) Remove the fixing screw of the developing unit, and pull out the developing unit. 3) Remove two screws. Remove the DV cover.
PAGE 11
1 : '10/Jun/18 C. Toner density reference control level setting 1) Insert the power plug into a power outlet. With the front cabinet open, turn ON the power switch of the machine and the power switch on the operation panel. 2) With the front cabinet open, enter SIM 25-2. 2) Open the front cabinet, and insert the toner cartridge slowly. 1 WARNING: Do not install the toner cartridge before completing the Toner density reference control level setting (SIM 25-2). 3) Close the front cabinet.
PAGE 12
1 3) : '10/Jun/18 Install the paper holding plate unit. 2) Touch the [Paper Tray Settings] key. 3) Touch the [Paper Tray Settings] key to configure the settings. These settings specify the paper type, paper size, and functions allowed for each paper tray. When the [Tray Settings] key is touched, a list appears showing the trays and the current settings. 4) Touch the [Change] key in the above screen to change the settings. The following settings can be configured.
PAGE 13
2) Adjust the guide plates A and B by squeezing their lock levers and sliding them to match the vertical and horizontal dimensions of the paper to be loaded. [Check with the servicing color test chart (UKOG-0317FCZZ/ UKOG-0317FC11 or UKOG-0326FCZZ/UKOG-0326FC11)] Check to confirm that it is in the conditions shown below. The guide plates A and B are slidable. Slide each guide plate while squeezing its lock lever. Serviceman chart (Color patch section) A Patch 7 is slightly copied or not copied.
PAGE 14
J. Function and operation check (2) Check that the following operations are normal.
PAGE 15
C. Check the packed items Service Manual MX-M503N [2] MX-DEX8/DEX9 1. 1) Check that all the items are included in the package. Unpacking A. Removal of the desk unit 1 No. 1 2 2. 2 Names of bundles Right adjuster Fixing screws (M4 x 8) Quantity 1 4 Installation * Before starting installation, check to insure that the data lamp on the operation panel does not light up or blink. A. Turn off the power of the main unit 1) Turn OFF the power switch on the operation panel.
PAGE 16
B. Installation of the adjuster 2) 1) Install the right adjuster (package part No. 1) to the desk unit. 2) Turn each adjuster to fix the desk unit. Put the main unit on the desk unit. * Use man power of four persons or more to lift the main unit. * Place the main unit on the desk unit slowly by fitting the external lines. Check to insure that the positioning pin on the top of the desk unit is securely engaged in the positioning groove of the main unit. C.
PAGE 17
5) Lift the connection plates on the right and left of the main unit front side, and fix them with the fixing screws (package part No. 2). 6) Replace the No. 3 and No. 2 trays to the original positions. 7) Lift the connection plates, and fix them with the fixing screws. 8) Install the connection plate covers.
PAGE 18
D. Release the lock E. Connector connection 1) Pull out each tray. 1) Remove the screw from the back of the main unit. Remove the connector cover. 2) Turn and remove the fixing material, and remove the caution sheet. 2) Connect the connector. 3) Attach the removed fixing material to the position shown in the figure for storage. 3) Split the removed connector cover along the perforated line. 4) Install the connector cover and fix it with a screw.
PAGE 19
F. Turn on the power of the main unit (Note) 1) By pressing [LEAD] or [OFFSET] button, the following items can be executed individually. Insert the power plug of the main unit into the power outlet. * [LEAD]: Print image lead edge image position adjustment * [OFFSET]: Print image off-center adjustment When [ALL] is selected, both of the above two items are executed simultaneously. 4) Select a paper feed tray to be adjusted.
PAGE 20
[3] MX-LCX1 MX-M503N 1. 3) Remove the paper feed desk fixing screw. Service Manual Unpacking A. Removal of the large capacity tray unit NOTE: Before turning on the power, check to insure that the fixing screw of the tray is removed. If the power is turned on without removing the fixing screw, a trouble may be resulted. C. Check the packed items 1) Check that all the items are included in the package. B. Removal of the fixing material and packing parts 1) 1 Remove the fixing material.
PAGE 21
2) Open the front cabinet. 3) Disengage the pawl, and remove the right adjuster. Turn OFF the power switch in the front cabinet of the main unit. 1 1 OFF 2 3) Disconnect the power plug of the main unit from the power outlet. 4) Remove the screw cap, and remove the screw. 2 1 5) Remove the cover. 6) Temporarily fix the fixing screw B (package part No. 4) midway. B. Connection of the main unit and the large capacity tray unit 1) Install the mounting plate upper (package part No.
PAGE 22
7) Insert the temporarily fixed screw B into the key hole in the connection unit (package part No. 2), and temporarily fix the connection unit. 2) Check to insure that the height adjustment check rib of the large capacity tray unit and the axis line of the mounting plate upper mounted to the main unit are in the same line. 1 2 8) Fix the other fixing screw B (package part No. 4), and tighten the temporarily fixed screw B securely.
PAGE 23
5) In the case of a shift to the right, press the front upper section and fit the height adjustment check rib so that it is in the same line with the axis line of the mounting plate upper. Insert the large capacity tray unit into the main unit. 2) Connect the connector, and tighten the screw. E. Paper size switch (1) Paper size switch from A4 to LT Since the factory setting of the paper size is A4, if paper size switch is required, perform the following procedures.
PAGE 24
a. Side plate size switch 2) Loosen the fixing screw (flat screw 1pc) of the auxiliary guide. 1) 3) Set the mark position ( ) of the auxiliary guide and the cassette R to the size from A4 to LT, and fix with the fixing screw (flat screw). Remove four fixing screws (blue screws) which are fixing the upper and the lower sections of the side plate F and the side plate R.
PAGE 25
3) 4) Slightly push the tray, restore the stopper to the original position, and fix the fixing screw. 2) Loosen the stopper fixing screw (1 pc) on the right lower side of the tray so that the stopper does not function. At that time, check to insure that the stopper pawl is engaged with the stopper reception of the large capacity tray unit. 3) Pull out the tray again until it stops. a. Side plate size switch Slowly insert the tray to the original position.
PAGE 26
F side 3) R side Slightly push the tray, restore the stopper to the original position, and fix the fixing screw. b. Auxiliary guide size switch At that time, check to insure that the stopper pawl is engaged with the stopper reception of the large capacity tray unit. * Since the auxiliary guide setting is not required, fix the auxiliary guide to either of A4 or LT. (To prevent against missing of the part) c.
PAGE 27
2) Open the front cabinet. 4) Select a paper feed tray to be adjusted. Turn ON the power switch in the front cabinet of the main unit. ǂǂǂ6,08/$7,21ǂǂ12 7(67 &/26( $872 ,0$*( 326,7,21 $'-8670(17 6(59,&( ON 0)7 &6 &6 &6 &6 /&& $'8 (;(&87( 3) 5) Press [EXECUTE] key. 6) Set the adjustment pattern on the document table. (Any direction) Turn ON the power switch on the operation panel. The adjustment pattern is printed out. G.
PAGE 28
2) Loosen the stopper fixing screw (1 pc) on the right lower side of the tray so that the stopper does not function. 2) Slowly insert the tray to the original position. Then make a copy to check to insure that there is no more shift. Repeat the procedures until there is no shift. b.
PAGE 29
MX-M503N [4] MX-FNX9 B. Removal of the fixing tape and protection Service Manual material 1. 1) Unpacking Remove the fixing tape and protection material. A. Removal of the inner finisher C. Check the packed items 1) Check that all the items are included in the package. 1 2 4 3 5 6 7 * When removing the inner finisher, lift it as shown in the table below. 8 No.
PAGE 30
1 2. : '10/Jun/18 Installation C. Installation of the inner finisher 1) Open the front cover. 2) Remove two screws, and remove the front cabinet upper. 3) Disengage two pawls, and remove the paper exit tray cover. 4) Remove four screws, and remove the paper exit tray. * Before starting installation, check to insure that the data lamp on the operation panel does not light up or blink. A.
PAGE 31
5) Remove the paper exit full detection actuator. 6) Engage the projection on the main unit frame with the hole in the finisher fixing plate (package part No. 1). 7) Fix the right cover plate with the fixing screw (package part No. 8). 9) Fix the dummy punch unit (package part No. 3) with the fixing screw (package part No. 8). 10) Check to insure that the slide roller is in the rail groove, and insert the inner finisher. 11) Fix the rear slide rail with the fixing screw (package part No. 8).
PAGE 32
13) Install the front open/close cover (package part No. 4) to the front rail stay rotating shaft, and fix it with the resin clip (package part No. 9). D. Connector Installation 1) Remove the protection material and fixing tape. 2 1 2 1 14) Fix the punch cover (package part No. 5) together with the band (metal fixture) with the fixing screw (package part No. 8). 2) Remove the screw, and remove the connector cover.
PAGE 33
E. Staple position label attachment F. Turn on the power of the main unit 1) 1) Insert the power plug of the main unit into the power outlet. 2) Open the front cabinet. Attach the label to the position indicated in the figure. [For scanner] (package part No. 11) Second label Corner R end fitting Label attachment reference Corner of the "upper cabinet rear" Corner R end fitting Turn ON the power switch in the front cabinet of the main unit. ON [For DSPF/RSPF] (package part No.
PAGE 34
MX-M503N [5] MX-PNX1 2. Installation Service Manual 1. * When the punch unit is installed together with installation of the MX-FNX9 (inner finisher), first install the inner finisher, and then install the punch unit. Unpacking A. Removal of the punch unit * Before starting installation, check to insure that the data lamp on the operation panel does not light up or blink.
PAGE 35
B. Installation of the punch unit 1) Open the front cabinet. 2) Open the front cover and slide the inner finisher to the left. 5) Remove two screws, and remove the front cabinet upper. 6) Remove the screw, and remove the band and the punch cover. 7) Remove the screw, and remove the dummy punch unit. 8) Fix the punch unit with a screw. 2 1 3) Remove the coin screw, and remove the finisher slide stopper. 4) Slide the inner finisher further more.
PAGE 36
9) Make positioning with the dove (A) and fix the punch unit with the screw which was fixing the dummy punch unit. 13) Insert the dust box. A A 14) Install the front cabinet upper part using the two screws removed in step 5). 10) Cut the lid of the punch cover with nippers. 11) Remove the dust box. 15) Insert the finisher slide stopper between the slide rail and the accuride, and fix it with the coin screw. 12) Fix the punch cover and the band together with one screw.
PAGE 37
C. Punch position label attachment D. Turn on the power of the main unit 1) 1) Insert the power plug of the main unit into the power outlet. 2) Open the front cabinet. Attach the label to the position indicated in the figure. [For scanner] (Part No. 13 in the package of the MX-FNX9) Lose the clearance. First label Second label Corner R end fitting Label attachment reference Corner of the "upper cabinet rear" Corner R end fitting Turn ON the power switch in the front cabinet of the main unit.
PAGE 38
[6] MX-RBX3 MX-M503N 1. C. Check the packed items Service Manual 1) Check that all the items are included in the package. Unpacking A. Removal of the interface pass unit 1 5 4 No. 1 2 3 4 5 6 7 2.
PAGE 39
1 : '10/Jun/18 B. Removal of the paper holding plate unit 1 1) 3) Remove the screws, and remove the paper exit tray. * When removing the paper exit tray, there is no need to remove the screws in the section (A). Disengage the pawl, and remove the paper holding plate and the paper holding plate holder together as a unit. * Be careful to remove both of the paper holding plate (which is easily removed alone) and the paper holding plate holder.
PAGE 40
6) Insert the rib of the interface left cabinet (package part No. 2) into the slit on the lower surface of the scanner left cabinet. Install the interface left cabinet with the fixing screw A (package part No. 4) of the paper exit tray which was removed in procedure 4). 9) Remove the front connection cabinet from the front cabinet upper, and attach it to the front cabinet upper C (package part No. 7). 10) Install the front cabinet upper C unit, and fix with the screws.
PAGE 41
[7] MX-FN10 MX-M503N 1. 3) Remove the skid and packing cushions. Service Manual Unpacking A. Removal of the saddle finisher * For removal of the saddle stitch finisher, manpower of two persons or more is required. 1) Remove the fixing material, and remove the top case. Remove the packing cushion and bundled items. 4) One person tilt the saddle stitch finisher, another person remove the lower tray. 1 2 5) 2) Remove the other side similarly.
PAGE 42
B. Removal of the fixing tape and protection material 2. Installation 1) * Make sure that none of the data lamps on the operation panels are lit or flashing before starting the installation work. Remove the fixing tape and protection material. * Installing the MX-FN10 requires that the option desk (MX-DEX8/ DEX9) and junction unit (MX-RBX3) be installed in advance.
PAGE 43
2) Fix the paper holding A with fixing screws A (package part No. 6). (1) 1) When the guide pin is not fit with the connection hole in the finisher: Loosen the fixing screw of the adjustment section on the rear side. Adjust the height adjustment screw so that the guide pin is fit with the connection hole in the finisher. * By making space between the main body and ground, the adjustment screw can be turned by the finger. 2 3) 1 Installation of tee saddle tray and paper holding B.
PAGE 44
(2) When the guide pin is fit with the connection hole in the finisher: 1) Insert the finisher into the main unit. Check to insure that the upper and lower clearances between the main unit and the finisher are even. E. Connection of the main unit and saddle finisher 1) Fix the connection plate (package part No. 2) to the paper feed desk with fixing screws B (package part No. 7). 2) Install the rail bracket to the frame with fixing screws C (package part No. 8).
PAGE 45
2) Connect the finisher connector with the connector of the main unit, and tighten the screw. H. Turn on the power of the main unit 1) Insert the power plug of the main unit into the power outlet. 2) Open the front cabinet. Turn ON the power switch in the front cabinet of the main unit. G. Staple position label attachment 1) Attach the label to the position indicated in the figure. [For scanner] (package part No.
PAGE 46
[8] MX-PNX5A/B/C/D MX-M503N 3) Disconnect the power plug of the main unit from the power outService Manual let. 1. Unpacking A. Removal of the punch unit 4) Disconnect the connector between the main unit and the saddle finisher. B. Check the packed items 1) Check that all the items are included in the package. 1 2 000-0000 3 No. 1 2 3 Packed part names Harness A (Purple) Harness B (Gray) Punch jam processing label Quantity 1 1 1 * Use the punch position labels bundled with the MX-FN10. 2.
PAGE 47
2) 3) Remove the screw, and remove the rear cover. 5) Remove the screw, and remove the dummy punch guide. 6) Install the punch unit to the saddle finisher. Fix the punch unit with the screw which was removed from the dummy punch guide. Remove the screw, and remove the front lower cover. * Before installing, remove the dust box. * Check to confirm that the punch guide pin is securely inserted into the guide pin insertion hole of the finisher.
PAGE 48
8) Fix the front inner cover with screws, and close the front cover. 11) Install the saddle finisher to the main unit. C. Punch jam processing label attachment 1) 9) Open the front cover, apply the punch jam processing label (package part No. 3) in position as shown in the figure. Fix the front lower cover with a screw. 000-0000 Label attachment reference 2 D. Punch position label attachment 1 1) Attach the label to the position indicated in the figure.
PAGE 49
[For DSPF/RSPF] 2) Insert the power plug of the main unit into the power outlet. 3) Open the front cabinet. DSPF 1mm 1mm Turn ON the power switch in the front cabinet of the main unit. ON RSPF 1mm 1mm E. Turn on the power of the main unit 1) 4) Turn ON the power switch on the operation panel. Connect the connector.
PAGE 50
[9] MX-FN11 MX-M503N 4) Remove the skid and packing cushions. Service Manual 1. Unpacking A. Removal of the finisher * For removal of the finisher, manpower of two persons or more is required. 1) Remove the fixing material, and remove the top case. 2) Remove the bundled items from packing cushion. 5) One person tilt the finisher, another person remove the lower tray.
PAGE 51
B. Removal of the protection material C. Check the packed items 1) 1) Remove the fixing tapes and protection material. Check that all the items are included in the package. 1 2 4 3 5 7 6 8 9 X3 X3 11 10 13 2) 3) 12 14 15 16 Open the front upper door, and remove the fixing tapes and protection material. Remove the screws and remove the fixing material for the paper exit tray. (four positions) No.
PAGE 52
2. Installation 2) Install the rail reception sheet metal (Package part No. 6) to the main unit with the fixing screws (Package part No. 2). * Installing the MX-FN11 requires that the option desk (MX-DEX8/ DEX9) and junction unit (MX-RBX3) be installed in advance. Be sure to complete the installation of the option desk (MX-DEX8/ DEX9) and junction unit (MX-RBX3) before installing the finisher.
PAGE 53
4) D. Attaching the mylar Remove the reverse tray. 1) Attach the mylar (package part No.13) to the position indicated in the figure. Reference Reference Corner reference Corner reference 5) Remove the screws, and remove the interface left cabinet. E. Installation of the connection fixture F/R 6) 1) Install the connection fixture R (Package part No. 8) to the main unit with the fixing screws (Package part No. 3). 2) Install the connection fixture F (Package part No.
PAGE 54
F. Attaching the cushion 1) 3) Attach the cushion (S) (package part No.14), the cushion (M) (package part No.15) and the cushion (L) (package part No.16) to the position indicated in the figure. Check that the center of the screw hole of the finisher is in the range of specification of an oval hole of the connection fixture that exist on main body rear side.
PAGE 55
2) Remove the screw, slide to the left the front lower cover, and remove it. 3) Open the front upper door, and remove the screw. 4) 5) Remove the fixing tapes. 6) Remove the screws, and remove the auxiliary wheels. 7) Remove the screws, and remove the rear lower cover. 8) Remove the fixing tapes. Remove the screws, and open the front cover.
PAGE 56
9) Loosen both of the caster fixing screws of the front side and rear side. 11) Turn the bolt for which the adjustment is necessary, and adjust to become it within the range of specification. 12) Check to insure that the upper and lower clearances between the main unit and the finisher are even. 10) Remove the screw, and remove the spanner installed inside the front lower door.
PAGE 57
13) Tighten the caster fixing screws so that the indicator scale is fit. 16) Install the spanner for adjustment to inside the front lower door. 17) Close the front cover, and secure it with the fixing screws. 14) Install the rear lower cover with the fixing screws. 18) Attach the fixing screw, and close the front upper door. 15) Install the auxiliary wheels with the fixing screws.
PAGE 58
19) Attach the front lower cover with the fixing screw. 4) Close the front cover. 5) Remove the screw, and remove the connector cover on rear side of the finisher. 6) Install the Step screw B (Package part No. 4). 7) Attach the connector cover on rear side of the finisher. I. Connection of the finisher 1) Engage the finisher to the main unit. 2) Open the front cover of finisher. 3) Fix the finisher to the main unit with the step screw B (Package part No. 4).
PAGE 59
J. Connection of connector to the main unit 1) [For DSPF/RSPF] (Package part No. 10) Connect two connectors of the finisher to the main unit, and tighten the screws. DSPF 1mm 1mm RSPF 1mm 1mm K. Staple position label attachment 1) Attach the label to the position indicated in the figure. [For scanner] (Package part No. 9) L. Turn ON the main power switch of the main unit 1) Connect the power plug of the main unit into the power outlet. 2) Open the front cabinet of the main unit.
PAGE 60
MX-M503N [10] MX-PNX6A/B/C/D 2) Open theManual front cover, and open the top cover. Service 1. Unpacking 2 A. Pulling out of the punch unit 1) Pull out the punch unit. 1 3) Remove the screws, and remove the fixing material. (2 positions) 4) Close the top cover, and close the front cover. B. Removal of the protection material 1) Remove the fixing tape and protection material.
PAGE 61
C. Check the packed items 1) 3) Check that all the items are included in the package. 1 2 Hang the punch unit on the step screws installed to the finisher. 3 2 5 4 1 6 7 8 P P No. 1 2 3 4 5 6 7 8 Names of bundles P tight M4x12 Step screw A Cap screw M3x6 Binding head M4x12 Front cover Front cover mounting fixture Connection fixture F (for punch) Connection fixture R (for punch) 4) Tighten the step screws bundled to the punch unit, fix the punch unit.
PAGE 62
6) 7) C. Install of the Connection fixture F/R Open the front door of punch unit. Engage the pawls of the rear side of front cover (Package part No. 5), attach the front cover with the fixing screw (Package part No. 1). B. Connection of connector of the finisher and punch unit 1) Remove the fixing screws, and remove the rear cover. 1) Install the Connection fixture F (Package part No. 7) to the main unit with the fixing screws (Package part No. 4).
PAGE 63
2) E. Adjustment Open the front door of punch unit. * Refer to the adjustment procedures in the MX-FN11 Service Manual. F. Install to main unit 3) 1) Engage the finisher that has installed punch unit to the main unit. 2) Open the front door of punch unit. 3) Secure the main unit and the punch unit with the fixing screw (Package part No. 4 of the MX-FN11).
PAGE 64
4) Close the front door of punch unit. 5) Install the fixing screw (Package part No. 4 of MX-FN11) on rear side. 8) G. Connection of connector to the main unit 1) 6) Install the connector cover of the finisher and fix it with the fixing screw. Connect two connectors of the finisher to the main unit, and tighten the screws. Install the rear cover of punch unit with the fixing screws. H. Punch position label attachment 1) Attach the punch position label to the position indicated in the figure.
PAGE 65
[For DSPF/RSPF] (Package part No. 12 of the MX-FN11) DSPF 1mm 1mm RSPF 1mm 1mm I. Turn ON the main power switch of the main unit 1) Connect the power plug of the main unit into the power outlet. 2) Open the front cabinet of the main unit. Turn ON the power switch in the front cabinet. ON 3) Turn ON the power switch on the operation panel.
PAGE 66
MX-M503N [11] MX-TRX2 3) Remove the power plug of the main unit from the outlet. Service Manual 1. Unpacking A. Removal of the exit tray unit B. Installation of the exit roller unit 1) Open the right door. 2 1 B. Check the packed items 1) Check that all the items are included in the package. 1 No. 1 2 2) Remove the screw, and remove the connector cover. 3) Remove the screw. Disengage the engagement in the front side then in the rear side, and remove the paper exit cover.
PAGE 67
4) Connect the connector, and install the exit roller unit (package part No. 1). Use the screw which was removed in step 3) and fix the unit. C. Turn on the power of the main unit. 1) Insert the power plug of the main unit into the power outlet. 2) Open the front cabinet. Turn ON the power switch in the front cabinet of the main unit. 5) Install the connector cover, and fix it with the screw. ON 3) Turn ON the power switch on the operation panel. D.
PAGE 68
MX-M503N [12] MX-FXX2 B. Attach Manual the fax box unit to the rear part of the Service main unit. 1. 1) Remove the two screws from the rear cabinet of the main unit. 2) Attach the supplied step screw to one of the two positions from which the screws are removed. Unpacking A. Parts included M3 Screw: Installation directions: Line cable: Australia 2. 3) Insert the step screw into the mounting hole of the fax box unit.
PAGE 69
3) Remove the two screws from the control PWB unit. 4) Pull out the control PWB unit. F. Attach the control PWB and the right cabinet rear. 1) Push the control PWB unit into the main unit and secure it with the two screws. 2) Cut out the cut-out portion of the right cabinet rear. D. Attach the FAX memory. 2 PROG1 PROG2 FAX IMG EXT PCL/BARCODE PS KANJI 3) Fit the interface cable into the opening that has been cut. 4) Attach the right cabinet rear cover to the main unit.
PAGE 70
I. Clear the FAX related software switches. G. Turn on the main power switch of the main unit. 1) 1) Enter the SIM 66-2 mode. Insert the power plug of the main unit to the outlet. ǂǂǂ6,08/$7,21ǂǂ12 7(67 &/26( )$; 62)7 6: &/($5 -$3$1 35(6(17˖ ǂǂ1(:˖ 6(7 $5( <28 685(" '(67 &2'( 2) Turn on the main power switch. <(6 (;(&87( 12 2) Enter the country code (8 digits) with the 10-key. 3) Press [SET], [EXECUTE], and [YES] keys.
PAGE 71
J. Clear the image memory. L. Installation completion check 1) 1) Enter the SIM 66-10 mode. ǂǂǂ6,08/$7,21ǂǂ12 7(67 &/26( ,0$*( 0(025< &/($5 Execute SIM 22-10 to check to confirm that the FAX box and the FAX memory are properly installed. When the FAX1 is properly connected, "MX-FXX2" is displayed. When the FAX memory is properly connected, "AR-MM9" is displayed.
PAGE 72
[13] AR-SU1 MX-M503N 1. 3) Disconnect the power plug from the power outlet. Service Manual Unpacking A. Remove the stamp unit B. Install the stamp unit 1) For removing and fixing screws, use a stubby screwdriver. B. Check the parts in the package 1) Check to confirm that all the parts are included in the package. 1 2 3 No.
PAGE 73
2) Remove the sensor cover. Remove the stamp case, and remove the earth cord. 3) Attach the stamp unit (package part No. 1) to the stamp case which was removed from the DSPF/RSPF unit with the installing screw (package part No. 4). (Fix it together with the earth wire.) 4) Install the stamp case unit, and connect the connector. 6) Install the stamp cartridge (package part No. 3). 7) Install the OC mat, and close the DSPF/RSPF unit.
PAGE 74
C. Turn on the power of the main unit 1) Insert the power plug into the power outlet. 2) Open the front cabinet of the machine, and turn ON the power switch. ON 3) Turn ON the power switch on the operation panel. 4) Use SIM22-10 to check to confirm that the finish stamp (ARSU1) is recognized.
PAGE 75
[14] MX-PB10 MX-M503N Service Manual 1. Unpacking A. Parts included 1 No. 1 2 2 Packed part names CD-ROM (Driver) Product key sheet (With Application Number) Quantity 1 1 2. Installation A. Preparation for enabling the MX-PB10 1) To enable the MX-PB10, enter the product key by the key operation of the copier machine. a) Press the system setting key on the operation panel. b) Select [Product key input] key display page, and touch the key. c) Touch the input column.
PAGE 76
2. Installation Service Manual [15] MX-PB11 MX-M503N A. Preliminary arrangements 1. Unpacking NOTE: When this option is installed to a machine which has been used by a user, be sure to backup the user data as shown below. When the MX-PB11 is installed, the user settings and the registered data are initialized. (The simulation settings and the adjustment data are not initialized.) Before installing the MX-PB11, save the user data. After completion of installation, the saved data. Must be restored.
PAGE 77
C. Pull out the control PWB 2) When installing the HDD to the MFP PWB frame, attach the anti-vibration rubber to the HDD frame side and fix it with a screw. • If cables are connected to the control PWB unit, remove all cables. 1) Push the location indicated in the illustration to unlock, and remove the cover from the right cabinet rear. 2) Remove the screw from the right cabinet rear. 3) Remove the right cabinet rear. 4) Remove the two screws from the control PWB unit.
PAGE 78
4) Push the control PWB unit into the main unit. G. Preparation for enabling the MX-PB11 5) Secure the unit with the two screws. 1) To enable the MX-PB11, enter the product key by the key operation of the copier machine. a) Turn on the power. (The product key input menu is displayed.) b) Enter the product key with numeric key (10-key), and touch [Registration] key. 2) After completion of entry of the product key, turn OFF the power switch on the operation panel.
PAGE 79
MX-M503N [16] MX-FWX1 * This option requires installation of a HDD, and cannot be used with the models having no HDD. When this option is used with the U model, the MX-PB11 option must be installed. 1. Unpacking B. Operation check of the Internet Fax send Service Manual function 1) After completion of entry of the product key, check to confirm that the Internet Fax send is performed normally from the machine.
PAGE 80
: '10/Jun/18 1 [17] MX-EBX3 MX-M503N B. Type A Manual Service (1) * This option cannot be installed to the U model. Parts included 1. Unpacking A3MXEBX3* FS9205S A 9B2 R. C. The MX-EBX3 is available in the following three types. Instillation must be performed according to the type. A. Old type (1) Identification marking A : Type A Parts included A3MXEBX3* The identification mark " A " is indicated on the side of the package of type A. 1 No.
PAGE 81
2. Installation 2) A. Turn off the power of the main unit 3) Remove the right cabinet rear. 4) Remove the two screws from the control PWB unit. 1) Turn the power switch located on the operation panel to the "OFF" position. 2) Open the front cabinet. Turn OFF the power switch in the front cabinet of the main unit. Remove the screw from the right cabinet rear. • If the fax box unit is installed, carry out steps 5), 6), and 7) additionally.
PAGE 82
3) Remove the S tight screw (section A) of the controller PWB. Use the removed S tight screw and the S tight screw provided in the package to attach the scanner function expansion PWB to the controller PWB. 4) Push the control PWB unit into the main unit. 5) Secure the unit with the two screws. At that time, check to confirm that the connectors (section B) of the both PWB’s are securely connected. A 6) Fit the interface cable into the right cabinet rear cover.
PAGE 83
2) Open the front cabinet. Turn ON the power switch in the front cabinet of the main unit. ON 3) Turn ON the power switch on the operation panel. 4) Use SIM22-5 to check the firmware version of the MX-EBX3. The ACRE version must be 02.00.J2 or later. If the version is 01.00.J2, revise the version according to the procedure of 5).
PAGE 84
[18] MX-PKX1 MX-M503N Service Manual 1. Unpacking Please keep below important information. This information will use for other products. A. Parts included 1 No. 1 2 2 Packed part names CD-ROM (For Screen Font) Product key sheet Quantity 1 1 NOTE: • N model To set up the PS driver, do not use the CD-ROM which is included in the MX-PKX1 but use the PCL CD-ROM which is included in the main unit.
PAGE 85
MX-M503N [19] MX-PUX1 Service Manual 1. Unpacking A. Check the packed items 1 No. 1 2 3 2 Packed part names CD-ROM Operation manual Product key sheet 3 Quantity 1 1 1 2. Installation To enable XPS, an expansion memory (MX-SMX3) must be installed. To install an expansion memory, refer to the descriptions of "[18] MX-SMX3" on this Installation manual. A. Preparation for enabling XPS 1) To enable XPS, enter the product key by the key operation of the copier machine.
PAGE 86
MX-M503N [20] MX-SMX3 4) Remove the two screws from the control PWB unit. Service Manual 1. Unpacking 5) Pull out the control PWB unit and remove the snap band. A. Parts included 6) Remove the interface cable from the frame. 7) Remove the connector. 8) Pull out and remove the control PWB unit. • If the fax box unit is installed, carry out steps 5), 6), and 7) additionally. 7 4 1 No. 1 2. Packed part name Expansion memory board 6 Quantity 1 3 8 5 Installation A.
PAGE 87
NOTE: Avoid diagonal insertion of the expansion memory board for the slot. 4) Push the control PWB unit into the main unit. 5) Secure the unit with the two screws. NOTE: Do not push one end of the expansion memory board by one hand. • If the fax box unit is installed, carry out step 6) additionally. 6) Fit the interface cable into the right cabinet rear cover. 7) Attach the right cabinet rear cover to the main unit. At this time, check that the four hooks are properly fitted to the main unit.
PAGE 88
2) Turn on the main power switch. ON 3) Turn on the power switch located on the operation panel.
PAGE 89
MX-M503N [21] AR-PF1 B. Pull outManual the control PWB. Service • If cables are connected to the control PWB unit, remove all cables. 1. Unpacking 1) Push the location indicated in the illustration to unlock, and remove the ozone filter cover from the right cabinet rear. 2) Remove the screw from the right cabinet rear. A. Parts included AR-PF1 barcode font ROM PWB 1 No. 1 2 2 Packed part names CD-ROM Operation Manual Quantity 1 1 2. Installation A. Turn off the power switches of the main unit.
PAGE 90
D. Reattach the control PWB and the right cabinet rear. E. Turn on the main power switch of the main unit. • If the fax box unit is installed, carry out steps 1), 2), and 3) additionally. 1) Insert the power plug of the main unit to the outlet. 2) Turn on the main power switch. 1) Connect the interface cable to the control PWB unit. 2) Push the interface cable into the recessed portion of the sheet metal on the control PWB unit. 3) Attach the snap band to the sheet metal of the control PWB unit.
PAGE 91
1 1 1 : '10/Jun/18 [22] MX-FR14U/FR14/FR15U/FR15/ FR24U 3) Remove the power plug of the main unit from the outlet. Service Manual * MX-FR14U/FR14 For model MX-M283N/M363N/M453N/M503N For model MX-M363U/M453U/M503U with HDD * MX-FR15U/FR15 For model MX-M363U/M453U/M503U without HDD * MX-FR24U For model MX-M282N/M362N/M452N/M502N 1. Unpacking A. Check the packed items 1) Check that all the items are included in the package. MFP_ B. Pull out the control PWB. PRG1 1 No. 1 2 3 2.
PAGE 92
C. Mount the data security kit ROMs to the control PWB unit. Remove the ROMs (PROG1 and PROG2) from the control PWB and replace them with the data security kit ROMs (MFP_PRG1 and MFP_PRG2). 6) Fit the interface cable into the right cabinet rear cover. 7) Attach the right cabinet rear cover to the main unit. At this time, check that the four hooks are properly fitted to the main unit. 8) Secure the right cabinet rear with the screw.
PAGE 93
1 : '10/Jun/18 2. Installation Service Manual [23] MX-KBX2 MX-M503N 1 * This option cannot be installed to the following models. * Before starting installation, check to insure that the data lamp on the operation panel does not light up or blink. MX-M363U/M453U/M503U MX-M282N/M362N/M452N/M502N 1. A. Turn off the power of the main unit Unpacking 1) Turn OFF the power switch on the operation panel. 2) Open the front cabinet.
PAGE 94
2) Disconnect the connector of the scan mother harness, and remove the screws. 5) Attach the rear cabinet, and fix it with the screws. 1 2 3) 4) Attach the USB hub PWB unit (part No.3 in the package) with the removed screws. C. Install the base unit 1) Place the protection sheet (part No.7 in the package) on the table glass. 2) Open the front cabinet, and remove the screw, and remove the front cabinet upper. 3) Remove the screw, and remove the operation base plate unit.
PAGE 95
4) Remove the screws and disconnect two connectors. Place the operation panel upside down on the protection sheet. D. Install the operation panel 1) Check that each harness is engaged with the rib. 2) Connect the connector. 3) Install the operation panel to the main unit, and fix it with the screw. *1 *3 *2 *1: Don't pull the lead wire. The connector can be locked. Hold the housing section of connector, pull out it. *2: Slowly pull the lead wire and disconnect the connector.
PAGE 96
5) 6) Slide and attach the operation base plate C (part No.2 in the package) to the operation base plate unit. F. Turn on the power of the main unit 1) Insert the power plug of the main unit into the power outlet. Install the operation base plate unit to the main unit, and fix it with the screws. 2) Turn ON the power switch inside the front cabinet. ON 7) Attach the front cabinet upper, and fix it with the screws. 3) Turn ON the power switch on the operation panel. G.
PAGE 97
3) Touch [Keyboard Select]. System Settings Default Settings Back Image Quality Adjustment Clock Adjust Keyboard Select 4) Select your desired language and touch [OK]. The keyboard layouts that can be selected are shown below. English (US) English (UK) French German Swedish Finnish Danish Russian Greek Turkish Norwegian System Settings Clock Adjust Keyboard Select 5) Press [CA] key to exit from system setting mode. End of language setting.
PAGE 98
MX-M503N [24] MX-AMX1 Service Manual * This option requires installation of a HDD, and cannot be used with the models having no HDD. When this option is used with the U model, the MX-PB11 and the MX-NSX1 options must be installed. 1. Unpacking A. Check the packed items 1 No. 1 2 3 2 3 Packed part names CD-ROM MX-AMX1 GETTING STARTED GUIDE Sharpdesk license kit Operation Manual Quantity 2 1 1 2.
PAGE 99
MX-M503N [25] MX-AMX2 2) When "OSA setting" key is touched, the menu below is disService Manual played. * This option requires installation of a HDD, and cannot be used with the models having no HDD. When this option is used with the U model, the MX-PB11 option must be installed. 1. Unpacking A. Check the packed items 1 No. 1 2 2 Packed part names CD-ROM Operation manual Quantity 1 1 3) • To set the base screen of document filing as the default display, touch the [Document Filing] key. 2.
PAGE 100
MX-M503N [26] MX-AMX3 2) When "OSA setting" key is touched, the menu below is disService Manual played. * This option requires installation of a HDD, and cannot be used with the models having no HDD. When this option is used with the U model, the MX-PB11 option must be installed. 1. Unpacking A. Check the packed items 1 No. 1 2 2 Packed part names CD-ROM Operation manual Quantity 1 1 3) • When the check box of [External Account Management is Enabled] is checked: 2.
PAGE 101
MX-M503N [27] Dehumidifying heater 1. Parts included Kit name Kit part code Heater electric component kit DKIT-0391FCZZ Heater kit DKIT-0385FCZZ (120V series) DKIT-0386FCZZ (230V series) Scanner heater kit 2. Service Manual DKIT-0383FCZZ (120V series) DKIT-0384FCZZ (230V series) Package part No.
PAGE 102
2) Cut the switch part of the left rear lower cabinet. 2) NOTE: Be careful not to damage the cabinet. Remove the snap band. Insert the supporter (package part No. 3) to the frame of the power unit, and attach the WH PWB (package part No. 4) on it. NOTE: Be careful not to break the PWB when mounting the PWB to the supporters. 3) Attach the label for heater switch (package part No. 2) to the left rear lower cabinet.
PAGE 103
C. Installation of the heater kit (2) (1) 1) Remove the tray 1 and the tray 2. 2) Install the heater unit to the main unit, and secure it with the screw (M3x5 S-tight) (package part No.11). 1) Assembling of the heater unit Installation of the heater unit Attach the heater (package part No. 6) to the heater mounting plate (package part No. 7), and secure it with the screw (M3x6 S-tight) (package part No. 8).
PAGE 104
4) Attach the core (This procedure only applies to the 230V series). Attach the AC-cable connection plate (only for 120V series), or attach the inlet mounting plate (only for 230V series). Secure it with screw. E. Installation of the scanner heater kit (1) Assembling of the scanner heater unit 1) Secure the marking position on the harness of the scanner heater (package part No.13) to the heater fixing plate (package part No.14) with the banding band (package part No.15).
PAGE 105
(2) Removal of the table glass, the paper exit cover 1) Remove the screw, and remove the SPF glass and the glass holder. Remove the table glass. 2) Remove the paper exit cover. 3) Connect the harness of the scanner heater. Install the heater fixing plate of the scanner heater unit, and secure it with the screw (M3x4 Round-tipped) (package part No. 17). 4) Install the scanner heater and secure it with the screw (M4x6 Bind machine screw) (package part No. 18). Pass the harness through the clamp.
PAGE 106
6) Move the lamp unit by hand and check that it move smoothly in all movable area. F. Operation check after installation 1) Turn on the dehumidifier heater switch. 2) Measure the resistance value between the earth terminal and the AC terminal (L side), and between the earth terminal and AC terminal (N side) with the circuit tester, and confirm they are not short-circuited. 3) When not using the heater after checking, turn off the dehumidifier heater switch.
PAGE 107
: '10/Jun/18 1 1 2. Installation Service Manual [28] MX-RP11 MX-M503N 1. Unpacking * Before starting installation, check to insure that the data lamp on the operation panel does not light up or blink. A. Removal of the RSPF A. Turn off the power of the main unit. 1) Turn OFF the power switch on the operation panel. 2) Open the front cabinet. Turn OFF the power switch in the front cabinet of the main unit.
PAGE 108
1 1 2) : '10/Jun/18 Cut the screw hole in the cabinet, and install the SPF step screw R (a) (package part No. 3) and the step screw R (b) (package part No. 2). b a 5) Raise the RSPF unit upright, and fix it with the accessory screw (M5 x 16) (package part No. 4). 6) Remove the connector cover. Connect the interface connector. b 2 a 2 1 3) Insert the SPF step screw R and the step screw R into the screw hole in the hinge section of the RSPF unit. Slide the unit toward the front side and close.
PAGE 109
1 1 : '10/Jun/18 C. RSPF parallelism adjustment 1) Make an RSPF parallelism adjustment sheet. Cut copy paper in the longitudinal direction. 20mm A4/Letter size 2) Perform the adjustment according to the flowchart below. a) Check section A. Start of the adjustment Place the RSPF height adjustment sheet between section A and the RSPF glass height adjustment resin surface (a), and close the RSPF unit. Slowly pull out the RSPF height adjustment sheet.
PAGE 110
1 : '10/Jun/18 1 c) Adjust the section F. Use a clearance gauge to check to confirm that the clearance in the section F is 4.3mm - 5.0mm. If not, loosen the fixing nut and turn the section E to adjust. Adjust the section F. * Insert a clearance gauge in the range of 20mm from the edge (a) of the OC mat. Is there a resistance in the section B? a Yes Section F 4.3 - 5.0mm No 20mm Increase the clearance in the section F until there is a resistance in the section B. However, the max. is 5.0mm.
PAGE 111
1 : '10/Jun/18 1 d) Check section B. Place the RSPF height adjustment sheet between section B and the RSPF glass height adjustment resin surface (a), and close the RSPF unit. Slowly pull out the RSPF height adjustment sheet. Check to insure that a slight resistance is felt when pulling out the RSPF height adjustment sheet. (If the boss in section B is in contact, it is O.K.) Check section B. * Be careful not to put the book sensor (b) on the height adjustment sheet.
PAGE 112
1 1 : '10/Jun/18 D. RSPF skew adjustment (Front surface mode) [Check Method 2] This adjustment is needed in the following situations: Check that the squareness of the main scanning direction print line for the longitudinal direction of paper is within 1.0mm. * The RSPF section has been disassembled. * When replacing the RSPF unit. * The RSPF unit generates skewed scanned images. 1) Create an adjustment chart by printing in duplex mode the selfprint pattern (grid pattern) specified in Simulation 64-2.
PAGE 113
1 1 5) : '10/Jun/18 Close the RSPF unit, and loosen the hex nut of the RSPF diagonal adjustment screw section. Turn the hex wrench of the RSPF diagonal adjustment screw to adjust the alignment. E. RSPF paper feed tray paper width sensor adjustment This adjustment is needed in the following situations: * The RSPF paper feed tray section has been disassembled. * The RSPF paper feed tray unit has been replaced. * When a U2 trouble occurs. * The scanner PWB has been replaced.
PAGE 114
1 1 : '10/Jun/18 F. Copy image off-center, image lead edge position, sub scanning direction image magnification ratio automatic adjustment (RSPF mode) 1) 7) * The screen shows a message indicating that the machine is reading and calculating RSPF adjustment patterns (for the front side). Enter the SIM50-28 mode. The machine starts calculating the adjustment amount (for the front side) after it has read the patterns for the front side.
PAGE 115
LEAD-FREE SOLDER The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The alphabet following the LF mark shows the kind of lead-free solder. Example: Lead-Free Solder composition code (Refer to the table at the right.
PAGE 116
CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to manufacturer’s instructions.
PAGE 117
COPYRIGHT © 2010 BY SHARP CORPORATION All rights reserved. Produced in Japan for electronic Distribution No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic; mechanical; photocopying; recording or otherwise without prior written permission of the publisher. Trademark acknowledgements • Microsoft®, Windows®, Windows® 98, Windows® Me, Windows NT® 4.