DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM MX-2010U/MX-2310U START GUIDE Keep this manual close at hand for reference whenever needed.
Caution! For complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations. The equipment should be installed near an accessible socket outlet for easy disconnection.
For the users of the fax function FAX interface cable and Line cable: These special accessories must be used with the device. The declaration of conformity may be consulted at: http://www.sharp.de/doc/MX-FX11.pdf SOFTWARE LICENCE The SOFTWARE LICENCE will appear when you install the software from the CD-ROM. By using all or any portion of the software on the CD-ROM or in the machine, you are agreeing to be bound by the terms of the SOFTWARE LICENCE.
Contents CAUTIONS ———————————————————————————— 5 SPECIFICATIONS ———————————————————————— 15 Symbols in this manual ———————————————————————— 5 Basic Specifications / Copier specifications ———————————————— 15 Power notes ————————————————————————————— 5 Automatic document feeder (Standard equipment) ———————————— 16 Installation notes ——————————————————————————— 6 Tray ————————————————————————————————— 16 About consumables —————————————————————————— 7 Finisher ——————————————————————————————— 16 H
CAUTIONS Symbols in this manual WARNING To ensure safe use of the machine, this manual uses various safety symbols. The safety symbols are classified as explained below. Be sure you understand Indicates a risk of death or serious injury. CAUTION Indicates a risk of human injury or property damage. the meaning of the symbols when reading the manual.
Installation notes CAUTION Do not install the machine on an unstable or slanted surface. Install the machine on a surface that can withstand the weight of the machine. Risk of injury due to the machine falling or toppling. If peripheral devices are to be installed, do not install on an uneven floor, slanted surface, or otherwise unstable surface. Danger of slippage, falling, and toppling. Install the product on a flat, stable surface that can withstand the weight of the product.
About consumables CAUTION Do not throw a toner cartridge into a fire. Store a toner cartridge out of the reach of children. Toner may fly and cause burns. Handling precautions WARNING Do not place a container of water or other liquid, or a metal object that might fall inside, on the machine. If you notice smoke, a strange odor, or other abnormality, do not use the machine. If the liquid spills or the object falls into the machine, fire or electrical shock may result.
CAUTION Do not look directly at the light source. Doing so may damage your eyes. Do not block the ventilation ports on the machine. Do not install the machine in a location that will block the ventilation ports. Blocking the ventilation ports will cause heat to build up in the machine, creating a risk of fire. The fusing unit and paper exit area are hot. When removing a misfeed, do not touch the fusing unit and paper exit area. Take care not to burn yourself.
SUPPLIES Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for the finisher. For best copying results, be sure to use only Sharp Genuine Be sure to use only SHARP-specified products for the toner cartridges, finisher Supplies which are designed, engineered, and tested to staple cartridge, and transparency film. maximize the life and performance of Sharp products.
Emission of noise and chemicals Noise emission values Noise emission values as measured according to ISO7779 are listed to the right. Sound power level LWAd Printing mode (continuous printing) 7.5 B Standby mode (Low power level mode) 3.6 B Sound pressure level LpA (actual measurement) Printing mode (continuous printing) Bystander positions 50 dB(A) Standby mode Bystander positions 19 dB(A) Emission density (measured according to RALUZ122: Edition Jun.
Part Names 1 2 3 4 5 7 6 1 Automatic document feeder (This is an option for MX-2010U) 2 Front cover 3 Output tray (Center tray) 4 Operation panel 5 Right tray 8 6 [POWER] key ( ) 7 Bypass tray 8 Main power switch 9 Tray 1 10 Tray 2 (when paper feed tray is installed)* 9 10 11 12 11 Tray 3 (when paper feed tray is installed)* 12 Tray 4 (when paper feed tray is installed)* * Peripheral device.
TURNING THE POWER ON AND OFF This machine has two power switches. The main power switch is at the bottom left after the front cover is opened. The other power switch is the [POWER] key ( the operation panel. ) on Turning on the power (1) Switch the main power switch to the “ (2) Press the [POWER] key ( ” position. ) to turn on the power. Turning off the power (1) Press the [POWER] key ( ) to turn off the power. (2) Switch the main power switch to the “ ” position.
OPERATION MANUALS AND HOW TO USE THEM The instructions for this manual are separated in the following three sections.
How to read the Operation Guide The [Operation Guide] can be downloaded from the machine and viewed on a computer. You can download the [Operation Guide] following the procedures below while the machine is connected to the network. 1 Confirm the machine’s IP address First, press the [SYSTEM SETTINGS] key on the operation panel and then touch [List Print (User)] when it appears on the touch panel. Next, select [NIC Page] from [Printer Test Page] and then touch the [Print] button.
SPECIFICATIONS Basic Specifications / Copier specifications Name MX-2010U/MX-2310U Type Desktop Same size: 1:1 ± 0.8 % Copy rations Colour Full colour Copier system Laser electrostatic copier Scan (full colour): 600 × 600 dpi Print: 600 × 600 dpi, equivalent to 9,600 dpi × 600 dpi Gradation Scan: equivalent to 256 levels / Print: equivalent to 256 levels Original paper sizes Max. A3 (11"×17") / sheets, bound documents Paper feed / capacity Max. paper feed / max.
SPECIFICATIONS Automatic document feeder Name MX-2010U: Reversing Single Pass Feeder (MX-RP12) MX-2310U: Standard equipment Document feeder types Reversing Single Pass Feeder (RSPF) Original paper sizes A3 (11" × 17") to A5 (5-1/2" × 8-1/2") Paper storage capacity Scan speed (copy) Plain paper 50 g/m2 (13 lbs.) to 128 g/m2 (32 lbs.) Two-sided (33/64")) B/W: 50 one-sided sheets/minute Paper weight Thin paper 35 g/m2 (9 lbs.) to 49 g/m2 (13 lbs.) Original paper types 100 sheets (80 g/m2 (21 lbs.
Punch module Name Paper size for punch module Punch module (MX-PN11A, MX-PN11B, MX-PN11C, MX-PN11D) for Required power supply Supplied from finisher finisher Weight Approx. 3 kg (7 lbs.) A3 (11" × 17") to B5R (7-1/4" × 10-1/2"R) Cannot punch special types of paper such as OHP.
SPECIFICATIONS Network Printer Specifications Type Built-in type Internal fonts (options) 80 fonts for PCL, 136 fonts for PS3 emulation Continuous print speed Same as continuous copy speed Memory Machine system memory and hard disk. Data processing: 600 × 600 dpi, Interface 10BASE-T/100BASE-TX/1000BASE-T, USB 2.
INFORMATION ON DISPOSAL Information on Disposal for Users (private households) In the European Union Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin! Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment.
Administrator Name: Contact at: Information that the administrator of the machine requires is printed on the back of this page. (Separate this page from the manual and keep it in a safe place. In addition, fill in the name of the administrator and the administrator’s contact information in the left hand margin.
TO THE ADMINISTRATOR OF THE MACHINE System settings password A password is necessary to change the machine’s system settings using administrator authority. System settings can be changed from either the operation panel or using a computer web browser. After setting up the machine, refer to [SYSTEM SETTINGS] in the Operation Guide to set a new password.
For the users of the fax function Important safety instructions • If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network. • Never install telephone wiring during a lightning storm. • Never install telephone jacks in wet locations unless the socket is specifically designed for wet locations.
Trademark acknowledgments The following trademarks and registered trademarks are used in conjunction with the machine and its peripheral devices and accessories. • Microsoft®, Windows®, Windows® 2000, Windows® XP, Windows Server® 2003, Windows Vista®, Windows Server® 2008, Windows® 7 and Internet Explorer® are registered trademarks or trademarks of Microsoft Corporation in the U.S.A. and other countries. • PostScript is a registered trademark of Adobe Systems Incorporated.
MX-2010U/MX-2310U START GUIDE PRINTED IN FRANCE TINSE4860GHZ1 *TINSE4860GHZ1*
