MX-2300N/2700N/3500N/3501N/4500N/4501N Operation-Manual Copier GB
Table Of Contents
- TABLE OF CONTENTS
- ABOUT THIS MANUAL
- BASIC PROCEDURE FOR MAKING COPIES
- BASE SCREEN OF COPY MODE
- COPYING SEQUENCE
- MAKING COPIES
- AUTOMATIC 2-SIDED COPYING
- COPY COLOUR MODES
- CHANGING THE EXPOSURE AND EXPOSURE MODE
- REDUCTION/ENLARGEMENT/ZOOM
- ORIGINAL SIZES
- OUTPUT
- MAKING COPIES USING THE BYPASS TRAY (Copying on special papers)
- INTERRUPTING A COPY RUN (Interrupt copy)
- JOB STATUS SCREEN
- CONVENIENT COPY FUNCTIONS
- SPECIAL MODES
- ADDING MARGINS (Margin Shift)
- ERASING PERIPHERAL SHADOWS (Erase)
- COPYING EACH FACING PAGE OF A BOUND DOCUMENT (Dual Page Copy)
- MAKING COPIES IN PAMPHLET FORMAT (Pamphlet Copy)
- COPYING A LARGE NUMBER OF ORIGINALS AT ONCE (Job Build)
- USING TWO MACHINES TO COPY A LARGE NUMBER OF ORIGINALS (Tandem Copy)
- USING A DIFFERENT PAPER TYPE FOR COVERS (Covers/Inserts)
- ADDING INSERTS WHEN COPYING ON TRANSPARENCY FILM (Transparency Inserts)
- COPYING MULTIPLE PAGES ONTO ONE SHEET OF PAPER (Multi Shot)
- COPYING A PAMPHLET (Book Copy)
- COPYING CAPTIONS ONTO TAB PAPER (Tab Copy)
- COPYING BOTH SIDES OF A CARD ON ONE SHEET OF PAPER (Card Shot)
- PRINTING THE DATE AND A STAMP ON COPIES (Stamp)
- CHECKING THE STAMP LAYOUT (Layout)
- REPEATING PHOTOS ON A COPY (Photo Repeat)
- CREATING A LARGE POSTER (Multi-Page Enlargement)
- REVERSING THE IMAGE (Mirror Image)
- COPYING A3 (11" x 17") SIZE ORIGINAL WITHOUT CUTTING OFF THE EDGES (A3 (11x17) Full Bleed)
- COPYING IN THE CENTRE OF THE PAPER (Centring)
- REVERSING BLACK AND WHITE IN A COPY (B/W Reverse)
- ADJUSTING RED/GREEN/BLUE IN COPIES (RGB Adjust)
- ADJUSTING THE SHARPNESS OF AN IMAGE (Sharpness)
- WHITENING FAINT COLOURS IN COPIES (Suppress Background)
- ADJUSTING THE COLOUR (Colour Balance)
- ADJUSTING THE BRIGHTNESS OF A COPY (Brightness)
- ADJUSTING THE INTENSITY OF A COPY (Intensity)
- CHECKING COPIES BEFORE PRINTING (Proof Copy)
- COPYING ORIGINALS OF DIFFERENT SIZES (Mixed Size Original)
- COPYING THIN ORIGINALS (Slow Scan Mode)
- STORING COPY OPERATIONS (Job Programs)
- APPENDIX
123
6
Touch the key of the desired destination
position.
The touched position key is highlighted and the print position
changes.
The keys that show the print positions will appear as follows
depending on the state of the settings.
The above key is the top left key. The appearance of the keys
varies by position.
If you wish to swap the position of the selected print item with the position of another print item, temporarily move
either one of the print items to an unoccupied position and then switch the print positions.
7
Touch the [OK] key.
If you attempt to move the print item to a position that is already
occupied by another print item, a message will appear asking
you if you wish to overwrite the other print item. To overwrite
the other print item, touch the [Yes] key. To cancel the move,
touch the [No] key.
8
Touch the [OK] key.
9
Touch the [OK] key.
Move
Select the location to move the selected item.
OK
Not selected, stamp setting has not
been selected.
Selected during selection of the stamp
setting.
Not available, stamp setting has already
been allocated.
Move
Select the location to move the selected item.
OK
An item has been already selected to
this location. Overwrite the item?
No Yes
Layout
OK
DO NOT COPY
1,2,3..
AAA AAA
CONFIDENTIAL
1
4
2
5
3
6
1 2 3
4 5 6
Stamp
OKCancelLayout
1/2
Date
Page
Numbering
Stamp
Text