MX-2300N/2700N/3500N/3501N/4500N/4501N Operation-Manual Copier GB
Table Of Contents
- TABLE OF CONTENTS
- ABOUT THIS MANUAL
- BASIC PROCEDURE FOR MAKING COPIES
- BASE SCREEN OF COPY MODE
- COPYING SEQUENCE
- MAKING COPIES
- AUTOMATIC 2-SIDED COPYING
- COPY COLOUR MODES
- CHANGING THE EXPOSURE AND EXPOSURE MODE
- REDUCTION/ENLARGEMENT/ZOOM
- ORIGINAL SIZES
- OUTPUT
- MAKING COPIES USING THE BYPASS TRAY (Copying on special papers)
- INTERRUPTING A COPY RUN (Interrupt copy)
- JOB STATUS SCREEN
- CONVENIENT COPY FUNCTIONS
- SPECIAL MODES
- ADDING MARGINS (Margin Shift)
- ERASING PERIPHERAL SHADOWS (Erase)
- COPYING EACH FACING PAGE OF A BOUND DOCUMENT (Dual Page Copy)
- MAKING COPIES IN PAMPHLET FORMAT (Pamphlet Copy)
- COPYING A LARGE NUMBER OF ORIGINALS AT ONCE (Job Build)
- USING TWO MACHINES TO COPY A LARGE NUMBER OF ORIGINALS (Tandem Copy)
- USING A DIFFERENT PAPER TYPE FOR COVERS (Covers/Inserts)
- ADDING INSERTS WHEN COPYING ON TRANSPARENCY FILM (Transparency Inserts)
- COPYING MULTIPLE PAGES ONTO ONE SHEET OF PAPER (Multi Shot)
- COPYING A PAMPHLET (Book Copy)
- COPYING CAPTIONS ONTO TAB PAPER (Tab Copy)
- COPYING BOTH SIDES OF A CARD ON ONE SHEET OF PAPER (Card Shot)
- PRINTING THE DATE AND A STAMP ON COPIES (Stamp)
- CHECKING THE STAMP LAYOUT (Layout)
- REPEATING PHOTOS ON A COPY (Photo Repeat)
- CREATING A LARGE POSTER (Multi-Page Enlargement)
- REVERSING THE IMAGE (Mirror Image)
- COPYING A3 (11" x 17") SIZE ORIGINAL WITHOUT CUTTING OFF THE EDGES (A3 (11x17) Full Bleed)
- COPYING IN THE CENTRE OF THE PAPER (Centring)
- REVERSING BLACK AND WHITE IN A COPY (B/W Reverse)
- ADJUSTING RED/GREEN/BLUE IN COPIES (RGB Adjust)
- ADJUSTING THE SHARPNESS OF AN IMAGE (Sharpness)
- WHITENING FAINT COLOURS IN COPIES (Suppress Background)
- ADJUSTING THE COLOUR (Colour Balance)
- ADJUSTING THE BRIGHTNESS OF A COPY (Brightness)
- ADJUSTING THE INTENSITY OF A COPY (Intensity)
- CHECKING COPIES BEFORE PRINTING (Proof Copy)
- COPYING ORIGINALS OF DIFFERENT SIZES (Mixed Size Original)
- COPYING THIN ORIGINALS (Slow Scan Mode)
- STORING COPY OPERATIONS (Job Programs)
- APPENDIX
159
STORING COPY OPERATIONS (Job Programs)
A job program is a group of copy settings stored together. When copy settings are stored in a job program, the settings
can be called up and used for a copy job by means of a simple operation.
For example, suppose A3 (11" x 17") size CAD drawings are copied once a month for archive purposes using the
following settings:
(1) The A3 (11" x 17") size CAD drawings are reduced to A4 (8-1/2" x 11") size.
(2) The drawings have fine lines that do not show clearly, and thus a dark exposure setting (level 4) is used.
(3) To reduce paper use by a half, 2-sided copying is used.
(4) Margin shift is used so that holes can be punched for filing.
When a job program is not stored When a job program is stored
Set A3 (11" x 17") to A4 (8-1/2" x 11") reduction
Change the exposure setting
Select 2-sided copying
Select margin shift
Select punch hole settings
Press the [COLOUR START] key or the [BLACK & WHITE
START] key.
Press the [Program] key ( ).
Touch the stored program key.
Press the [COLOUR START] key or the [BLACK & WHITE
START] key.
Considerable time is required to copy the drawings each
month because the above settings must be selected.
In addition, mistakes are occasionally made when selecting
the settings, so some copies must be redone.
The settings are stored in a job program, so they can be
selected by the touch of a key. This is simple and takes no time.
In addition, the settings are all stored so there are no chances for
mistakes, and thus no need to redo copies due to setting mistakes.
• Up to 48 job programs can be stored. The job programs are retained even if an interruption occurs in the power supply.
• Job programs can also be stored in the Web pages. Click [Job Program Registration] and then [Copier] in the Web page
menu to store a job program.
A3 (11" x 17") size CAD drawings
Copies
or
Job Programs
Press program number.
5 6 7
3
8
41 2
1/6
Exit
Store/Delete
Recall
or