MX-2300N/2700N/3500N/3501N/4500N/4501N Operation-Manual Copier GB
Table Of Contents
- TABLE OF CONTENTS
- ABOUT THIS MANUAL
- BASIC PROCEDURE FOR MAKING COPIES
- BASE SCREEN OF COPY MODE
- COPYING SEQUENCE
- MAKING COPIES
- AUTOMATIC 2-SIDED COPYING
- COPY COLOUR MODES
- CHANGING THE EXPOSURE AND EXPOSURE MODE
- REDUCTION/ENLARGEMENT/ZOOM
- ORIGINAL SIZES
- OUTPUT
- MAKING COPIES USING THE BYPASS TRAY (Copying on special papers)
- INTERRUPTING A COPY RUN (Interrupt copy)
- JOB STATUS SCREEN
- CONVENIENT COPY FUNCTIONS
- SPECIAL MODES
- ADDING MARGINS (Margin Shift)
- ERASING PERIPHERAL SHADOWS (Erase)
- COPYING EACH FACING PAGE OF A BOUND DOCUMENT (Dual Page Copy)
- MAKING COPIES IN PAMPHLET FORMAT (Pamphlet Copy)
- COPYING A LARGE NUMBER OF ORIGINALS AT ONCE (Job Build)
- USING TWO MACHINES TO COPY A LARGE NUMBER OF ORIGINALS (Tandem Copy)
- USING A DIFFERENT PAPER TYPE FOR COVERS (Covers/Inserts)
- ADDING INSERTS WHEN COPYING ON TRANSPARENCY FILM (Transparency Inserts)
- COPYING MULTIPLE PAGES ONTO ONE SHEET OF PAPER (Multi Shot)
- COPYING A PAMPHLET (Book Copy)
- COPYING CAPTIONS ONTO TAB PAPER (Tab Copy)
- COPYING BOTH SIDES OF A CARD ON ONE SHEET OF PAPER (Card Shot)
- PRINTING THE DATE AND A STAMP ON COPIES (Stamp)
- CHECKING THE STAMP LAYOUT (Layout)
- REPEATING PHOTOS ON A COPY (Photo Repeat)
- CREATING A LARGE POSTER (Multi-Page Enlargement)
- REVERSING THE IMAGE (Mirror Image)
- COPYING A3 (11" x 17") SIZE ORIGINAL WITHOUT CUTTING OFF THE EDGES (A3 (11x17) Full Bleed)
- COPYING IN THE CENTRE OF THE PAPER (Centring)
- REVERSING BLACK AND WHITE IN A COPY (B/W Reverse)
- ADJUSTING RED/GREEN/BLUE IN COPIES (RGB Adjust)
- ADJUSTING THE SHARPNESS OF AN IMAGE (Sharpness)
- WHITENING FAINT COLOURS IN COPIES (Suppress Background)
- ADJUSTING THE COLOUR (Colour Balance)
- ADJUSTING THE BRIGHTNESS OF A COPY (Brightness)
- ADJUSTING THE INTENSITY OF A COPY (Intensity)
- CHECKING COPIES BEFORE PRINTING (Proof Copy)
- COPYING ORIGINALS OF DIFFERENT SIZES (Mixed Size Original)
- COPYING THIN ORIGINALS (Slow Scan Mode)
- STORING COPY OPERATIONS (Job Programs)
- APPENDIX
42
OUTPUT
To select output functions and the output tray, touch the [Output] key in the base screen of copy mode. Output functions
that can be selected are sort, group, offset, staple sort, saddle stitch, and punch. All settings are explained in this section
based on the assumption that a saddle stitch finisher, punch module and right tray are installed.
(1) [Group] key
This is used to group copies by page.
☞ Group mode (page 43)
(2) [Staple Sort] key
This is used to sort the output into sets, staple each set,
and deliver the sets to the tray. (Note that the sets will not
be offset in the output tray.) When this function is
selected, three keys will appear for selecting the staple
position.
☞ Staple sort function / Saddle stitch function (page 44)
(3) [Sort] key
This is used to sort (collate) output into sets.
☞ Sort mode (page 43)
(4) Output display
An icon will appear to indicate the output mode.
(5) [Offset Tray] key ([Centre Tray] key*)
This is used to offset each set of output from the previous
set in the offset tray (centre tray). The [Offset Tray] key is
automatically selected when the [Staple Sort] key is
selected.
* When only a right tray is installed, this appears as the
"Centre tray".
(6) [Right Tray] key
Select this key to have output delivered to the right tray.
When the right tray is selected, offset, staple sort, saddle
stitch, and punch cannot be selected.
(7) [OK] key
Touch this key to close the output screen and return to
the base screen.
(8) [Offset] key
This is used to offset each set of output from the previous set.
The offset function operates when the checkbox is
selected and does not operate when the checkbox is
not selected . (The offset checkmark is automatically
cleared when the staple sort function is selected.)
☞ Offset function (page 43)
(9) [Saddle Stitch] key
This is used to staple and fold each set of copies at the centreline.
☞ Staple sort function / Saddle stitch function (page 44)
When this key is touched, the saddle stitch setting screen
appears. (Only when "Automatic Saddle Stitch" is
enabled in the system settings (administrator).)
(10) [Punch] key
This is used to punch holes in the output.
☞ Punch function (page 45)
Output
Sort
Staple
Sort
Group
OK
Offset
Tray
Right Tray
Offset
Saddle
Stitch
Punch
(8)
(5)(3)(2)(1)
(7)
(9)
(10)
(4) (6)
The keys that appear and that can be selected will vary depending on what peripheral devices are installed.
Depending on what peripheral devices are installed, it may not be possible to select certain keys. If your screen is different
from the above screen, see the screens below.
Display example 1
The screen when a right tray, finisher, and
saddle stitch finisher are not installed.
Display example 2
The screen when a right tray is installed.
Display example 3
The screen when a right tray, finisher
and punch module are installed.
Output
Sort
Group
OK
Offset
Centre
Tray
Right Tray
Output
Sort
Group
OK
Offset
Staple
Sort
Punch
Offset
Tray
Right Tray
Output
Sort
Group
OK
Offset