MX-FXX1 Operation-Manual GB
Table Of Contents
- TABLE OF CONTENTS
- ABOUT THIS MANUAL
- BEFORE USING FAX MODE
- BASIC TRANSMISSION METHODS
- TRANSMISSION METHODS
- USING THE AUTOMATIC DOCUMENT FEEDER FOR TRANSMISSION
- USING THE DOCUMENT GLASS FOR TRANSMISSION
- TRANSMISSION BY REDIALLING (RESEND)
- TRANSMISSION USING THE SPEAKER
- CHANGING THE RESOLUTION AND EXPOSURE
- SPECIFYING THE ORIGINAL SCAN SIZE AND SEND SIZE (Enlarge/Reduce Sending)
- AUTOMATICALLY SCANNING BOTH SIDES OF AN ORIGINAL (2-sided original)
- ENTERING DESTINATION FAX NUMBERS
- FAX RECEPTION
- CHECKING THE STATUS OF FAX JOBS
- PRINTING A TRANSACTION REPORT / IMAGE SENDING ACTIVITY REPORT
- CONVENIENT FUNCTIONS
- SENDING THE SAME FAX TO MULTIPLE DESTINATIONS (Broadcast transmission)
- SENDING A FAX AT A SPECIFIED TIME (Timer)
- ERASING PERIPHERAL SHADOWS ON THE IMAGE (Erase)
- TRANSMITTING AN ORIGINAL AS TWO SEPARATE PAGES (Dual Page Scan)
- SENDING TWO PAGES AS A SINGLE PAGE (2in1)
- SENDING BOTH SIDES OF A CARD AS A SINGLE PAGE (Card Shot)
- STORING FAX OPERATIONS (Program)
- ADDING YOUR SENDER INFORMATION TO FAXES (Own number sending)
- TRANSMITTING ORIGINALS OF DIFFERENT SIZES (Mixed Size Original)
- FAXING THIN ORIGINALS (Slow Scan Mode)
- SENDING A LARGE NUMBER OF PAGES (Job Build)
- CALLING A FAX MACHINE AND INITIATING RECEPTION (Polling)
- SENDING A FAX WHEN ANOTHER MACHINE POLLS YOUR MACHINE (Polling memory)
- FORWARDING RECEIVED FAXES (Fax Data Forward)
- SENDING A FAX DIRECTLY FROM A COMPUTER (PC-Fax)
- FORWARDING A RECEIVED FAX TO AN E-MAIL ADDRESS (Inbound Routing Settings)
- PERFORMING F-CODE COMMUNICATION
- USING AN EXTENSION PHONE
- IF THE MACHINE IS MOVED
- SYSTEM SETTINGS FOR FAX
- System Settings
- Accessing the System Settings (General)
- System Settings (General) List
- List Print (User)
- Address Control
- Storing a One-touch (Individual) Key for Fax
- Storing a Group Key
- Storing a Program
- Amend/Delete a One-touch Key or Program
- Programming an F-code Memory Box (Polling Memory)
- Programming an F-code Memory Box (Confidential)
- Programming an F-code Memory Box (Relay Broadcast)
- Editing and Deleting F-code Memory Boxes
- Changing the Name of a Custom Index
- Fax Data Receive/Forward
- Accessing the System Settings (Administrator)
- System Settings (Administrator) List
- Operation Settings
- Device Control
- Image Send Settings
- List Print (Administrator)
- Enable/Disable Settings
45
This chapter explains the basic procedures for receiving a fax.
RECEIVING FAXES
When "Auto Reception" is enabled, the machine will receive faxes automatically.
The fax reception mode is displayed in the base screen.
4
FAX RECEPTION
• When fax reception is in progress, it is possible to reserve a transmission by performing the transmission in memory
transmission mode.
☞ TRANSMISSION METHODS (page 13)
• To print received faxes, make sure that the required paper is loaded in the machine's paper trays. It is not necessary to
load A4 (8-1/2" x 11") paper and B5 (5-1/2" x 8-1/2") paper in both the vertical ( ) and horizontal ( ) orientations.
Differences in orientation are automatically adjusted when faxes are received.
When a fax smaller than A4 (8-1/2" x 11") size is received, the size of the paper used for printing will vary depending on the
orientation (vertical or horizontal) in which the sender placed the original.
• System Settings for Fax: Fax Receive Settings
This is used to change the fax reception mode. "Auto Reception" should normally be used.
Select "Manual Reception" when an extension phone is connected to the machine.
☞ Fax Receive Settings (page 161)
• System Settings for Fax (Administrator): Anti Junk Fax Setting (page 185)
This setting is used to enter fax numbers from which you wish to block reception.
Quick File
File
Special Modes
Sub Address
Speaker
Resend
Address Book
Fax
Mode Switch
Direct TX
Memory TX
Auto Reception
Ready to send.
Image
Settings
Fax Memory:100%
This shows the current fax
reception mode and the amount
of free memory remaining.