!mxc380p_en_ins.book 1 ページ ２０１０年３月１１日 木曜日 午後３時２７分 MODEL: MX-C380P MX-C380P Software Setup Guide N FRANCE E4699GHZZ DIGITAL FULL COLOUR PRINTER Software Setup Guide BEFORE INSTALLING THE SOFTWARE SETUP IN A WINDOWS ENVIRONMENT SETUP IN A MACINTOSH ENVIRONMENT TROUBLESHOOTING Keep this manual close at hand for reference whenever needed.
!mxc380p_en_ins.book 2 ページ ２０１０年３月１１日 木曜日 午後３時２７分 Thank you for purchasing this product. This manual explains how to install and configure the software that allows the machine to print. If the software is not installed correctly or you need to remove the software, see "4. TROUBLESHOOTING" (page 56). Please note • The explanations in this manual assume that you have a working knowledge of your Windows or Macintosh computer.
!mxc380p_en_ins.book 1 ページ ２０１０年３月１１日 木曜日 午後３時２７分 TABLE OF CONTENTS 1 BEFORE INSTALLING THE SOFTWARE CD-ROMS AND SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 • SOFTWARE CD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 VERIFYING SYSTEM REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 • SYSTEM REQUIREMENTS. . . . . . . . . . . . . . . . . . . . . . . . . .
!mxc380p_en_ins.book 1 2 ページ ２０１０年３月１１日 木曜日 午後３時２７分 BEFORE INSTALLING THE SOFTWARE This chapter describes the software programs that allow you to use the printer function of the machine, the CD-ROMs that contain the software, and the pages where the installation procedures can be found. CD-ROMS AND SOFTWARE The software that can be used with the machine is on the CD-ROMs that accompany the machine.
!mxc380p_en_ins.book 3 ページ ２０１０年３月１１日 木曜日 午後３時２７分 CD-ROMS AND SOFTWARE - PPD driver The PPD driver enables the machine to use the standard Windows PS printer driver. ☞ WHEN THE MACHINE IS CONNECTED TO A NETWORK (page 9) ☞ WHEN THE MACHINE WILL BE CONNECTED WITH A USB CABLE (page 21) • Printer Status Monitor (can only be used when the machine is connected to a network) This allows you to monitor the status of the machine on your computer screen.
!mxc380p_en_ins.book 4 ページ ２０１０年３月１１日 木曜日 午後３時２７分 VERIFYING SYSTEM REQUIREMENTS SYSTEM REQUIREMENTS Before installing the software described in this manual, make sure that your computer satisfies the following requirements. Windows Macintosh*5 Operating system*1 Windows 98, Windows Me, Windows NT Workstation 4.
!mxc380p_en_ins.book 5 ページ ２０１０年３月１１日 木曜日 午後３時２７分 VERIFYING SYSTEM REQUIREMENTS SOFTWARE REQUIREMENTS The following requirements must be met to use the software described in this manual.
!mxc380p_en_ins.book 6 ページ ２０１０年３月１１日 木曜日 午後３時２７分 CONNECTING THE MACHINE CONNECTING TO A NETWORK To connect the machine to a network, connect the LAN cable to the machine's network connector. Use a shielded LAN cable. After connecting the machine to a network, be sure to configure the IP address and other network settings before installing the software. (The factory default setting for the IP address is to receive the IP address automatically when the machine is used in a DHCP environment.
02_Setup.fm 2 7 ページ ２０１０年３月１１日 木曜日 午後３時３４分 SETUP IN A WINDOWS ENVIRONMENT This section explains how to install the software and configure settings so that the printer function of the machine can be used with a Windows computer. For users of Windows 98/Me/NT 4.0 The CD-ROM does not include software for Windows 98/Me/NT 4.0. Contact your dealer or nearest authorised service representative if you want software for Windows 98/Me/NT 4.0. if you want software for Windows 98/Me/NT 4.0.
!mxc380p_en_ins.book 8 ページ ２０１０年３月１１日 木曜日 午後３時２７分 OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE) 4 The "SOFTWARE LICENSE" window will appear. Make sure that you understand the contents of the license agreement and then click the [Yes] button. You can show the "SOFTWARE LICENSE" in a different language by selecting the desired language from the language menu. To install the software in the selected language, continue the installation with that language selected.
!mxc380p_en_ins.book 9 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER To install the printer driver, follow the appropriate procedure in this section depending on whether the machine is connected to a network or connected by USB cable. ☞ WHEN THE MACHINE WILL BE CONNECTED WITH A USB CABLE (page 21) WHEN THE MACHINE IS CONNECTED TO A NETWORK This section explains how to install the printer driver when the machine is connected to a Windows network (TCP/IP network).
!mxc380p_en_ins.book 10 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER X Standard installation When the software selection screen appears in step 6 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 7), perform the steps below. 1 Click the [Printer Driver] button. 2 Click the [Standard installation] button. When [Custom installation] is selected, you can change any of the items below.
!mxc380p_en_ins.book 11 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER • Machine connection method: LPR Direct Print (Auto Search) • Set as default printer: Yes • Printer driver name: Cannot be changed • Display fonts: Installed If you selected [Custom installation], select [LPR Direct Print (Auto Search)] and click the [Next] button.
02_Setup.fm 12 ページ ２０１０年３月１５日 月曜日 午後１時３分 INSTALLING THE PRINTER DRIVER 5 When the printer driver selection window appears, select the printer driver to be installed and click the [Next] button. Click the checkbox of the printer driver to be installed so that a checkmark ( ) appears. The [PPD] checkbox only appears if you are using Windows 2000/XP/ Server 2003/Vista/Server 2008/7.
!mxc380p_en_ins.book 13 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 7 Follow the on-screen instructions. Read the message in the window that appears and click the [Next] button. Installation begins. • If you are using Windows Vista/Server 2008/7 If a security warning window appears, be sure to click [Install this driver software anyway].
!mxc380p_en_ins.book 14 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER X Installation by specifying the machine's address When the machine cannot be found because it is not powered on or otherwise, installation is possible by entering the name (host name) or IP address of the machine. When the software selection screen appears in step 6 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 7), perform the steps below. 1 Click the [Printer Driver] button.
!mxc380p_en_ins.book 15 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 3 When you are asked how the printer is connected, select [LPR Direct Print (Specify Address)] and click the [Next] button. 4 Enter the name (host name) or IP address of the machine and click the [Next] button. ☞ Checking the IP address of the machine (page 6) 5 When the model selection window appears, select the model name of your machine and click the [Next] button.
!mxc380p_en_ins.book 16 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 6 When the printer driver selection window appears, select the printer driver to be installed and click the [Next] button. Click the checkbox of the printer driver to be installed so that a checkmark ( appears. ) The [PPD] checkbox only appears if you are using Windows 2000/XP/ Server 2003/Vista/Server 2008/7. 7 Select whether or not you wish the printer to be your default printer and click the [Next] button.
!mxc380p_en_ins.book 17 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 10 Follow the on-screen instructions. Read the message in the window that appears and click the [Next] button. Installation begins. • If you are using Windows Vista/Server 2008/7 If a security warning window appears, be sure to click [Install this driver software anyway].
!mxc380p_en_ins.book 18 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER X Printing using the IPP function and the SSL function The IPP function can be used to print to the machine over a network using HTTP protocol. The IPP function can also be used in combination with the SSL (encrypted communication) function to encrypt the print data. This enables secure printing with no concern that the data will be leaked to others.
!mxc380p_en_ins.book 19 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 2 Click the [Custom installation] button. 3 When you are asked how the printer is connected, select [IPP] and click the [Next] button. 4 If a proxy server is used, specify the proxy server and click the [Next] button. To specify a proxy server, select [Print via the proxy server] and then enter the [Address] and [Port number].
!mxc380p_en_ins.book 20 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 5 Enter the machine's URL and click the [Next] button. Enter the URL in the following format: Normal format: http://:631*1/ipp *1 Normally "631" should be entered for the port number. If the IPP port number has been changed on the machine, enter the new port number.
!mxc380p_en_ins.book 21 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER WHEN THE MACHINE WILL BE CONNECTED WITH A USB CABLE Supported operating systems: Windows 98/Me/2000*/XP*/Server 2003*/ Vista*/Server 2008*/7* * Administrator's rights are required to install the software. • Make sure that a USB cable is not connected to your computer and the machine. If a cable is connected, a Plug and Play window will appear.
!mxc380p_en_ins.book 22 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 2 Click the [Custom installation] button. 3 When you are asked how the printer is connected, select [Connected to this computer] and click the [Next] button. 4 When you are asked if you wish to install the display fonts, select an answer and click the [Next] button.
!mxc380p_en_ins.book 23 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 5 Follow the on-screen instructions. Read the message in the window that appears and click the [Next] button. When the installation completed screen appears, click the [OK] button. • If you are using Windows Vista/Server 2008/7 If a security warning window appears, be sure to click [Install this driver software anyway].
!mxc380p_en_ins.book 24 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 8 Installation of the PCL6 printer driver begins. When the "Found New Hardware Wizard" appears, select [Install the software automatically (Recommended)], click the [Next] button, and follow the on-screen instructions. • If you are using Windows Vista/Server 2008/7 If a security warning window appears, be sure to click [Install this driver software anyway].
!mxc380p_en_ins.book 25 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER When installing the PCL5c printer driver, PS printer driver, or PPD driver Installation is possible even after the USB cable has been connected. When the software selection screen appears in step 6 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 7), perform the steps below. 1 Click the [Printer Driver] button. 2 Click the [Custom installation] button.
!mxc380p_en_ins.book 26 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 3 When you are asked how the printer is connected, select [Connected to this computer] and click the [Next] button. 4 When the port selection window appears, select the port that the PCL6 printer driver is using (USB001, etc.) and click the [Next] button. 5 When the printer driver selection window appears, remove the [PCL6] checkmark and select the printer driver to be installed, and then click the [Next] button.
!mxc380p_en_ins.book 27 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 6 Select whether or not you wish the printer to be your default printer and click the [Next] button. If you are installing multiple drivers, select the printer driver to be used as the default printer. If you do not wish to set one of the printer drivers as the default printer, select [No]. 7 When the printer name window appears, click the [Next] button.
!mxc380p_en_ins.book 28 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER This completes the installation. • After installation, see "CONFIGURING THE PRINTER DRIVER FOR THE OPTIONS INSTALLED ON THE MACHINE" (page 34) to configure the printer driver settings. • Make sure that the port of the installed driver is the same as the port used by the PCL6 printer driver.
!mxc380p_en_ins.book 29 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER USING THE MACHINE AS A SHARED PRINTER If you are going to use the machine as a shared printer on a Windows network with the printer driver installed on a print server, follow the steps below to install the printer driver on the client computers. • Ask your network administrator for the server name and printer name of the machine on the network.
!mxc380p_en_ins.book 30 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 1 Click the [Printer Driver] button. 2 Click the [Custom installation] button. 3 Select [Shared Printer] and click the [Next] button.
!mxc380p_en_ins.book 31 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 4 Select the printer name (configured as a shared printer). (1) (2) (1) Select the printer name (configured as a shared printer on a print server) from the list. If you are using Windows 98/Me/NT 4.0/2000/XP/Server 2003, you can also click the [Add Network Port] button displayed below the list and select the printer to be shared by browsing the network in the window that appears. (2) Click the [Next] button.
!mxc380p_en_ins.book 32 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER USING THE STANDARD WINDOWS PS PRINTER DRIVER (Windows 98/Me/NT 4.0) If you wish to use the standard Windows 98/Me/NT 4.0 PS printer driver, follow the steps below to install the PPD driver using the Add Printer Wizard. • The CD-ROM does not include software for Windows 98/Me/NT 4.0. Contact your dealer or nearest authorised service representative if you want software for Windows 98/Me/NT 4.0.
!mxc380p_en_ins.book 33 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER X Installing the resident font information (Windows 98/Me) If you have installed the PPD driver on Windows 98/Me and will be using the resident fonts in the machine, you must install the resident font information. Follow the procedure below to install the resident font information. • Before installing the resident font information, be sure to install the PPD driver.
!mxc380p_en_ins.book 34 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER CONFIGURING THE PRINTER DRIVER FOR THE OPTIONS INSTALLED ON THE MACHINE After installing the printer driver, you must configure the printer driver settings appropriately for the options that have been installed and the size and type of paper loaded in the machine. Follow the steps below to configure the printer driver. If the PPD driver is installed, see "When the PPD driver is installed" (page 37).
!mxc380p_en_ins.book 35 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 4 Click the [Auto Configuration] button. The settings are automatically configured based on the detected machine status. *The screen shows the PCL6 printer driver. 5 Configure the image of the machine. An image of the machine is formed in the printer driver configuration window based on the options that are installed. (1) (2) (1) Select the options that are installed on the machine. (2) Click the [OK] button.
!mxc380p_en_ins.book 36 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER 6 Click the [OK] button in the printer properties window. If automatic configuration fails, configure the settings manually. • You can check the options that are installed and the tray settings by printing out the "All Custom Setting List" in the system settings of the machine. (However, note that "Input Tray Options" must be set to the number of trays on the machine.
!mxc380p_en_ins.book 37 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER DRIVER X When the PPD driver is installed 1 Click the [Start] button ( [Printer]. ), click [Control Panel], and then click • In Windows 7, click the [Start] button and then click [Devices and Printers]. • In Windows XP/Server 2003, click the [start] button and then click [Printers and Faxes]. • In Windows 98/Me/NT 4.0/2000, click the [Start] button, select [Settings], and then click [Printers].
!mxc380p_en_ins.book 38 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER STATUS MONITOR Printer Status Monitor is a printer utility that allows general users to check the current status of the machine on their computer screen, such as whether or not the machine is ready to print. The Printer Status Monitor shows error information such as paper misfeeds, printer configuration information (whether or not a finisher is installed, etc.
!mxc380p_en_ins.book 39 ページ ２０１０年３月１１日 木曜日 午後３時２７分 INSTALLING THE PRINTER STATUS MONITOR 2 Follow the on-screen instructions. 3 When the installation completed screen appears, click the [Finish] button. To have the Printer Status Monitor start automatically when your computer is started, select the [Add this program to your Startup folder] checkbox and click the [Finish] button. 4 Click the [Close] button in the window of step 1.
!mxc380p_en_ins.book 40 ページ ２０１０年３月１１日 木曜日 午後３時２７分 CHANGING THE PORT When using the machine in a Windows environment, follow the steps below to change the port when you have changed the IP address of the machine when the machine is connected with a USB cable. 1 Click the [Start] button ( [Printer]. ), click [Control Panel], and then click • In Windows 7, click the [Start] button and then click [Devices and Printers].
!mxc380p_en_ins.book 41 ページ ２０１０年３月１１日 木曜日 午後３時２７分 CHANGING THE PORT 3 Adding or changing a port. (1) Click the [Ports] tab. In Windows 98/Me, click the [Details] tab. (2) Click the [Add Port] button. (2) (1) To change to a previously created port such as USB port, select the desired port (USB001, etc.) from the list and click the [Apply] button. This changes the port. 4 Select [SC2 TCP/IP Port] and then click the [New Port] button.
!mxc380p_en_ins.book 42 ページ ２０１０年３月１１日 木曜日 午後３時２７分 CHANGING THE PORT 5 Create the new port. (1) Enter the machine's IP address. ☞ Checking the IP address of the machine (page 6) (2) Make sure that [LPR] is selected. (3) Make sure that [lp] is entered. (4) Click the [OK] button. (1) (2) (3) (4) 6 Click the [Close] button in the screen of step 4. 7 Make sure the created printer port is selected in the printer properties window and then click the [Apply] button.
!mxc380p_en_ins.book 3 43 ページ ２０１０年３月１１日 木曜日 午後３時２７分 SETUP IN A MACINTOSH ENVIRONMENT This chapter explains how to install the PPD file to enable printing from a Macintosh and how to configure the printer driver settings. ☞ MAC OS X: this page (v10.2.8, v10.3.9, v10.4.11, v10.5 - 10.5.8, v10.6) ☞ MAC OS 9.0 - 9.2.2: page 52 To use the machine in a Macintosh environment, the machine must be connected to a network. A USB connection cannot be used.
!mxc380p_en_ins.book 44 ページ ２０１０年３月１１日 木曜日 午後３時２７分 MAC OS X 4 Double-click the folder corresponding to the versions of the operating system. v10.2.8 v10.3.9 v10.4.11 v10.5 10.5.8 v10.6 5 Double-click the [MX-PBX1] icon ( ). If the "Authenticate" window appears in Mac OS X v10.2.8, enter the password and click the [OK] button. 6 Click the [Continue] button. 7 The License Agreement window will appear.
!mxc380p_en_ins.book 45 ページ ２０１０年３月１１日 木曜日 午後３時２７分 MAC OS X 8 Select the hard drive where the PPD file will be installed and click the [Continue] button. • Be sure to select the hard drive on which your operating system is installed. • In Mac OS X v10.6, the screen below appears when you click the [Change Install Location] button. 9 Click the [Install] button. Installation begins. If an authentication window appears, enter the password and click the [OK] button.
!mxc380p_en_ins.book 46 ページ ２０１０年３月１１日 木曜日 午後３時２７分 MAC OS X 11 Select [Utilities] from the [Go] menu. • If you are using Mac OS X v10.5 to 10.5.8 or v10.6, click [System Preferences] in the Apple menu ( ) and select [Print & Fax] ( ). When the screen for adding a printer appears, click the button and go to step 14. • If you are using Mac OS X v10.2.8, select [Applications] from the [Go] menu. 12 Double-click the [Printer Setup Utility] icon ( ). If you are using Mac OS X v10.2.
!mxc380p_en_ins.book 47 ページ ２０１０年３月１１日 木曜日 午後３時２７分 MAC OS X 14 Configure the printer driver. • The procedure for configuring the printer driver varies depending on the operating system version. The procedure for versions 10.4.11, 10.5 - 10.5.8 and 10.6 and the procedure for other versions are explained separately below. • The machine can print using the IPP function. If you wish to use the IPP function, see "Printing using the IPP function" (page 50) to configure the printer driver settings. v10.4.
!mxc380p_en_ins.book 48 ページ ２０１０年３月１１日 木曜日 午後３時２７分 MAC OS X v10.2.8, v10.3.9 (1) (2) (3) (4) (1) Select [AppleTalk]. If multiple AppleTalk zones are displayed, select the zone that includes the printer from the menu. (2) Click the machine's model name. The machine's model name usually appears as [SCxxxxxx]. ("xxxxxx" is a sequence of characters that varies depending on your model.) (3) Select the PPD file of the machine. • If you are using Mac OS X v10.3.9, select [Auto Select].
!mxc380p_en_ins.book 49 ページ ２０１０年３月１１日 木曜日 午後３時２７分 MAC OS X 15 Display printer information. (2) (1) (1) Click the machine's name. If you are using Mac OS X v10.5 to 10.5.8 or v10.6, click the [Options & Supplies] button, click the [Driver] tab and go to step 16. (2) Click [Show Info]. If you are using Mac OS X v10.2.8, select [Show Info] from the [Printers] menu. 16 Select the machine configuration.
!mxc380p_en_ins.book 50 ページ ２０１０年３月１１日 木曜日 午後３時２７分 MAC OS X X Printing using the IPP function The machine can print using the IPP function. If you wish to use the IPP function, follow these steps to select the PPD file when configuring the printer driver (step 14 on page 47). v10.4.11, v10.5 - 10.5.8, v10.6 (1) (2) (3) (4) (1) Click the [IP Printer] icon. If you are using Mac OS X v10.5 to 10.5.8 or v10.6, click the [IP] icon. (2) Select [Internet Printing Protocol] in "Protocol".
!mxc380p_en_ins.book 51 ページ ２０１０年３月１１日 木曜日 午後３時２７分 MAC OS X v10.2.8, v10.3.9 (1) (2) (3) (4) (1) Select [IP Printing]. (2) Select [Internet Printing Protocol] in "Printer Type". Enter the address of the machine (IP address or domain name) and the "Queue Name". • If you are using Mac OS X v10.2.8, enter the address of the machine (IP address or domain name) in "Printer's Address". • Enter "ipp" in "Queue Name". (3) Select [Sharp] in "Printer Model" and click the PPD file of your model.
!mxc380p_en_ins.book 52 ページ ２０１０年３月１１日 木曜日 午後３時２７分 MAC OS 9.0 - 9.2.2 If you are using Mac OS 9.0 to 9.2.2, make sure that "LaserWriter 8" has been installed and that the "LaserWriter 8" checkbox is selected in "Extensions Manager" in "Control Panels". If not, install it from the system CD-ROM supplied with your Macintosh computer. 1 Insert the "Software CD-ROM" into your computer's CD-ROM drive. 2 Double-click the [CD-ROM] icon ( 3 Double-click the [MacOS] folder.
!mxc380p_en_ins.book 53 ページ ２０１０年３月１１日 木曜日 午後３時２７分 MAC OS 9.0 - 9.2.2 7 Read the message in the window that appears and click the [Continue] button. Installation of the PPD file begins. After the installation, a message prompting you to restart your computer will appear. Click the [OK] button and restart your computer. This completes the installation of the software. Next, configure the printer driver settings. 8 Select [Chooser] from the Apple Menu. 9 Create a printer.
!mxc380p_en_ins.book 54 ページ ２０１０年３月１１日 木曜日 午後３時２７分 MAC OS 9.0 - 9.2.2 10 Select the PPD file. (1) (2) (1) Click the PPD file for your model. (2) Click the [Select] button. • If the above dialog box does not appear and you return to the "Chooser" dialog box, follow these steps to select the PPD file manually. (1) Make sure that the machine is selected in the "Select a PostScript Printer" list, and then click the [Setup] button followed by the [Select PPD] button.
!mxc380p_en_ins.book 55 ページ ２０１０年３月１１日 木曜日 午後３時２７分 MAC OS 9.0 - 9.2.2 13 Select the machine configuration. (1) Select the options that are installed on the machine. (2) Click the [OK] button. You can check the options that are installed on the machine by printing out the "All Custom Setting List" in the system settings. (However, note that "Input Tray Options" must be set to the number of trays on the machine.
!mxc380p_en_ins.book 4 56 ページ ２０１０年３月１１日 木曜日 午後３時２７分 TROUBLESHOOTING WHEN INSTALLATION WAS NOT SUCCESSFUL This section provides solutions to possible installation problems. See the following table of contents to locate the appropriate page for your question or problem. • The software cannot be installed. . . . . . . . . . . . . . . . . . . . . . . . . . 56 • The machine is not detected (when connected to a network).. . . . 57 • The plug and play screen does not appear (USB connection in Windows). . .
!mxc380p_en_ins.book 57 ページ ２０１０年３月１１日 木曜日 午後３時２７分 WHEN INSTALLATION WAS NOT SUCCESSFUL Problem The machine is not detected (when connected to a network). Point to check Solution Is the IP address of the machine configured? If the IP address of the machine is not configured, the machine will not be detected. Make sure that the IP address is configured correctly in "Network Settings" in the machine's system settings (administrator).
!mxc380p_en_ins.book 58 ページ ２０１０年３月１１日 木曜日 午後３時２７分 WHEN INSTALLATION WAS NOT SUCCESSFUL Problem Point to check Solution The plug and play screen does not appear (USB connection in Windows). Is the machine power on? When a USB cable is connected, make sure the power of the machine is "ON" and then connect a USB cable to the machine. When the machine is not powered on, switch on the main power switch and the [POWER] key ( ) in that order.
!mxc380p_en_ins.book 59 ページ ２０１０年３月１１日 木曜日 午後３時２７分 WHEN INSTALLATION WAS NOT SUCCESSFUL Problem The printer driver is not installed correctly by plug and play (USB connection in Windows).
!mxc380p_en_ins.book 60 ページ ２０１０年３月１１日 木曜日 午後３時２７分 WHEN INSTALLATION WAS NOT SUCCESSFUL X The printer driver cannot be installed (Windows 2000/XP/Server 2003) If the printer driver cannot be installed on Windows 2000/XP/Server 2003, follow the steps below to check your computer settings. 1 Click the [start] button and then click [Control Panel]. In Windows 2000, click the [Start] button, point to [Settings], and click [Control Panel]. 2 Click [Performance and Maintenance] and then [System].
!mxc380p_en_ins.book 61 ページ ２０１０年３月１１日 木曜日 午後３時２７分 REMOVING THE SOFTWARE To remove the printer driver or software installed using the installer, follow the steps below. X Windows 1 Click the [start] button and then click [Control Panel]. 2 Click [Uninstall a program]. In Windows 98/Me/NT 4.0/2000, click the [Start] button, point to [Settings], and click [Control Panel]. • In Windows XP/Server 2003, click [Add or Remove Programs]. • In Windows 98/Me/NT 4.
!mxc380p_en_ins.book 62 ページ ２０１０年３月１１日 木曜日 午後３時２７分 REMOVING THE SOFTWARE X Mac OS X 1 Delete the printer that uses the machine's PPD file from the printer list. To show the printer list, see step 11 and 12 of "MAC OS X" (page 43). 2 3 Delete the PPD file. The PPD file has been copied to the following folder on the startup disk. [Library] - [Printers] - [PPDs] - [Contents] - [Resources] - [en.lproj] Delete the PPD file of the machine from this folder. Delete the installation information.
!mxc380p_en_ins.
!mxc380p_en_ins.
!mxc380p_en_ins.
!mxc380p_en_ins.
