MODEL: MX-M850 MX-M950 MX-M1100 DIGITAL MULTIFUNCTIONAL SYSTEM Safety Guide Before installing this product, be sure to read the "CAUTIONS" and "INSTALLATION REQUIREMENTS" sections. CAUTIONS INSTALLATION REQUIREMENTS SUPPLIES SPECIFICATIONS INFORMATION ON DISPOSAL Keep this manual close at hand for reference whenever needed.
Each instruction also covers the optional units used with these products. Caution! For complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. To reduce the risk of fire, use only UL-Listed No.26 AWG or larger telecommunication line cord. Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations.
For the users of the fax function FAX interface cable and Line cable: These special accessories must be used with the device. The Declaration of Conformity can be viewed at the following URL address. http://www.sharp.de/doc/MX-FXX1.pdf Important Notice for New Zealand Users General "The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network.
Contents CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Inserter specifications. . . . . . . . . . . . . . . . . . . . . . 13 Laser information . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Finisher specifications . . . . . . . . . . . . . . . . . . . . . 14 INSTALLATION REQUIREMENTS . . . . . . . . . . . . . 5 Finisher (for MX-M850) specifications . . . . . . . . . 15 Saddle stitch finisher specifications . . . . . . . . . . . 16 SUPPLIES. . . . . . . . . . . . . .
CAUTIONS 1. Do not touch the transfer belt. Scratches or smudges on the transfer belt will cause dirty prints. 2. The fusing unit is extremely hot. Exercise care in this area. 3. Do not look directly at the light source. Doing so may damage your eyes. 4. When the machine is installed, the adjusters (4) must be lowered to the floor to secure the machine (prevent it from moving). Fusing unit Rotate the adjusters in the locking direction until they are in firm contact with the floor.
CAUTIONS Laser information Wave length 788 nm +12 nm -13 nm Pulse times (North America and Europe) 85 cpm model (4.9 µs ±4.9 ns)/7 mm 95 cpm model (3.6 µs ±3.6 ns)/7 mm 110 cpm model (3.6 µs ±3.6 ns)/7 mm Output power Max 2.25 mW (Total Power) (Four laser diodes) At the production line, the output power of the scanner unit is adjusted to 1.2 MILLIWATT (Total Power) PLUS 5% and is maintained constant by the operation of the Automatic Power Control (APC).
INSTALLATION REQUIREMENTS Improper installation may damage this product. Please note the following during initial installation and whenever the machine is moved. 1. The machine should be installed near an accessible power outlet for easy connection. 2. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded.
SUPPLIES Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for the finisher. Be sure to use only SHARP-specified products for the toner cartridges, finisher staple cartridge, saddle stitch finisher staple cartridge, and transparency film. For best copying results, be sure to use only Sharp Genuine Supplies which are designed, engineered, and tested to maximize the life and performance of Sharp products.
SPECIFICATIONS Machine specifications / copier specifications Name Digital Multifunctional System MX-M850/MX-M950/MX-M1100 Type Console Photoconductive type OPC drum Printing method Electrophotographic system (laser) Developer system Dry-type two-component magnetic brush development Fusing system Heat rollers Document glass 600 x 300 dpi (factory default values), 600 x 600 dpi, 600 x 400 dpi Scanning resolution Duplex single pass feeder (automatic document feeder) 600 x 300 dpi (factory defau
SPECIFICATIONS Machine specifications / copier specifications (Continued) Paper sizes: Tray 3 A3W, A3, B4, A4, A4R, B5, B5R, 12" x 18", 11" x 17", 9" x 12", 8-1/2" x 14", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R (Includes automatic paper size detection function.) Paper weight: Plain paper (60 g/m2 to 105 g/m2 (16 lbs. Bond to 28 lbs. Bond)), heavy paper (106 g/m2 to 205 g/m2 (28 lbs. Bond to 56 lbs. Index)) Paper capacity: 500 sheets (80 g/m2 (21 lbs.
SPECIFICATIONS Continuous copying speeds* Model MX-M850 Copy ratio MX-M950 MX-M1100 100% / Reduced / Enlarged A3W, 12" x 18" 34 copies/min. (42 copies/min.) 36 copies/min. (48 copies/min.) 39 copies/min. (57 copies/min.) A3, 8K 36 copies/min. (48 copies/min.) 38 copies/min. (53 copies/min.) 41 copies/min. (61 copies/min.) 11" x 17" 36 copies/min. (47 copies/min.) 38 copies/min. (51 copies/min.) 41 copies/min. (59 copies/min.
SPECIFICATIONS Acoustic noise emission* (measurement according to ISO7779) Sound power level LwA Model MX-M850/MX-M950 MX-M1100 Printing mode 7.8 B 7.8 B Standby mode 5.2 B 5.
SPECIFICATIONS Large capacity trays (MX-LCX4) specifications Model MX-LCX4 Paper sizes A4W, A4, B5, A5R, 9" x 12", 8-1/2" x 11", 5-1/2" x 8-1/2"R Paper weight Upper tray: 52 g/m2 to 205 g/m2 (16 lbs. Bond to 110 lbs. Index)) Middle tray:52 g/m2 to 205 g/m2 (16 lbs. Bond to 110 lbs. Index)) Lower tray: 52 g/m2 to 163 g/m2 (16 lbs. Bond to 90 lbs. Index)) Paper capacity Upper tray: 1000 sheets (80 g/m2 (21 lbs. Bond)) Middle tray:1000 sheets (80 g/m2 (21 lbs.
SPECIFICATIONS Bypass tray (for large capacity trays) specifications Model MX-MFX2*1 Paper sizes*2 A3W, A3, B4, A4W, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 9" x 12", 8-1/2" x 14", 8-1/2" x 13"-2/5, 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR, 318 mm x 469 mm, 318 mm x 234 mm, 312 mm x 440 mm, 312 mm x 220 mm, 320 mm x 450 mm, 320 mm x 225 mm (Includes automatic paper size detection function. Paper sizes can be entered.
SPECIFICATIONS Large capacity tray (MX-LCX3N) specifications Model MX-LCX3N* Paper sizes A3W, A3, B4, A4, A4R, B5, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R Paper weight 60 g/m2 to 205 g/m2 (16 lbs. Bond to 110 lbs. Index)) Paper capacity 3000 sheets (80 g/m2 (21 lbs.
SPECIFICATIONS Finisher specifications Model MX-FNX5 Paper sizes*1 A3W, A3, B4, A4W, A4, A4R, B5, B5R, A5, A5R, 12" x 18", 11" x 17", 9" x 12", 8-1/2" x 14", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2", 5-1/2" x 8-1/2"R, 8K, 16K, 16KR, 318 mm x 469 mm, 318 mm x 234 mm, 312 mm x 440 mm, 312 mm x 220 mm, 320 mm x 450 mm, 320 mm x 225 mm Paper weight Top tray: 52 g/m2 to 205 g/m2 (16 lbs. Bond to 110 lbs. Index) Offset tray: 52 g/m2 to 300 g/m2 (16 lbs.
SPECIFICATIONS Finisher (for MX-M850) specifications Model MX-FNX6*1 Paper sizes A3W, A3, B4, A4W, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 9" x 12", 8-1/2" x 14", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR, 318 mm x 469 mm, 318 mm x 234 mm, 312 mm x 440 mm, 312 mm x 220 mm, 320 mm x 450 mm, 320 mm x 225 mm Paper weight Top tray: 52 g/m2 to 205 g/m2 (16 lbs. Bond to 110 lbs. Index) Offset tray: 52 g/m2 to 300 g/m2 (16 lbs.
SPECIFICATIONS Saddle stitch finisher specifications Model MX-FNX7*1 Paper sizes A3W, A3, B4, A4W, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 9" x 12", 8-1/2" x 14", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR, 318 mm x 469 mm, 318 mm x 234 mm, 312 mm x 440 mm, 312 mm x 220 mm, 320 mm x 450 mm, 320 mm x 225 mm Paper weight Top tray: 52 g/m2 to 205 g/m2 (16 lbs. Bond to 110 lbs. Index) Offset tray: 52 g/m2 to 300 g/m2 (16 lbs.
SPECIFICATIONS Punch module (for MX-FNX5) specifications Model MX-PNX3A* MX-PNX3B* MX-PNX3C* MX-PNX3D* Hole punching 3 holes / 2 holes (switch manually) 3 holes / 2 holes (switch manually) 4 holes / 2 holes (switch manually) 4 holes, broad width Allowed paper sizes for punching 3 holes: A3, B4, A4, 11" x 17", 8-1/2" x 11"R, 5-1/2" x 8-1/2", 8K, 16K 2 holes: A3, B4, A4, A4R, B5, B5R, A5, 11" x 17", 8-1/2" x 14", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 5-1/2" x 8-1/2", 8K, 16K
SPECIFICATIONS Saddle unit specifications Model MX-FNX8*1 Paper sizes*2 A3, B4, A4W, A4, A4R, B5, B5R, A5, A5R, 11" x 17", 9" x 12", 8-1/2" x 14", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2", 5-1/2" x 8-1/2", 5-1/2" x 8-1/2"R, 8K, 16K, 16KR, 318 mm x 469 mm, 318 mm x 234 mm, 312 mm x 440 mm, 312 mm x 220 mm, 320 mm x 450 mm, 320 mm x 225 mm Paper weight 52 g/m2 to 300 g/m2 (16 lbs. Bond to 170 lbs.
SPECIFICATIONS Printer specifications*1 Type Built-in Continuous printing speed Same as continuous copying speed (When printing same document continuously on A4 (8-1/2" x 11") plain paper in non-offset mode, excluding processing time.
SPECIFICATIONS Network scanner*1 / Internet Fax*2 specifications Type Built-in 100 x 100, 200 x 200, 300 x 300, 400 x 400, 600 x 600 Scanning resolution (dpi) Internet Fax: 200 x 100, 200 x 200, 200 x 400, 400 x 400, 600 x 600 (200 x 100, 200 x 200 when file type is TIFF-S) Halftone can be selected for resolutions other than 200 x 100 dpi. Scanning speed Scanner MX-M850 Colour (A4 / 8-1/2" x 11")One-sided: 40 pages/min. (200 x 200 dpi)*3, Two-sided: 40 pages/min.
SPECIFICATIONS Facsimile specifications Model MX-FXX1 Applicable telephone line Public switched telephone network, PBX Scanning resolution (supports ITU-T standards) 8 x 3.85 lines/mm (Standard), 8 x 7.7 lines/mm (Fine, Fine-Halftone), 8 x 15.4 lines/mm (Super Fine, Super Fine - Halftone), 16 x 15.4 lines/mm (Ultra Fine, Ultra Fine - Halftone) Transmission speed 33.6 kbps down to 2.
INFORMATION ON DISPOSAL A. Information on Disposal for Users (private households) 1. In the European Union Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin! Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment.
✂ Contact at: Administrator Name: Information that the administrator of the machine requires is printed on the back of this page. (Separate this page from the manual and keep it in a safe place. In addition, fill in the name of the administrator and the administrator's contact information in the left hand margin.
TO THE ADMINISTRATOR OF THE MACHINE (Separate this page from the manual and keep it in a safe place.) Factory default passwords When accessing the system settings, the administrator password is required to log in with administrator rights. The system settings can be configured in the Web pages as well as on the operation panel. To access the system settings using the Web pages, a password is also required.
TO THE ADMINISTRATOR OF THE MACHINE For the users of the fax function IMPORTANT SAFETY INSTRUCTIONS • If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network. • The AC power outlet shall be installed near the equipment and shall be easily accessible. • Never install telephone wiring during a lightning storm.
TO THE ADMINISTRATOR OF THE MACHINE NOTICE FOR USERS IN AUSTRALIA AND NEW ZEALAND Your fax machine and the telephone system WARNING NOTICE: NO calls can be made to or from this fax during a mains power failure. WARNING Australian Communications Authority (ACA) regulations state that no unauthorized changes or modifications to this equipment are permitted.
TO THE ADMINISTRATOR OF THE MACHINE Trademark acknowledgments The following trademarks and registered trademarks are used in conjunction with the machine and its peripheral devices and accessories. • Microsoft®, Windows®, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000, Windows® XP, Windows Server® 2003, Windows® Vista and Internet Explorer® are registered trademarks or trademarks of Microsoft Corporation in the U.S.A. and other countries.
SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg
MX-M850/MX-M950/MX-M1100 Safety Guide PRINTED IN FRANCE TINSE3758GHZZ
