Software Setup Guide BEFORE INSTALLING THE SOFTWARE SETUP IN A WINDOWS ENVIRONMENT SETUP IN A MACINTOSH ENVIRONMENT TROUBLESHOOTING
Thank you for purchasing this product. This manual explains how to install and configure the software that allows the machine to be used as a printer or scanner for a computer. This manual also explains how to install the printer drivers and software that are used when the expansion kits are installed, and how to install the scanner driver. If the software is not installed correctly or you need to remove the software, see "4. TROUBLESHOOTING" (page 38).
TABLE OF CONTENTS 1 BEFORE INSTALLING THE SOFTWARE CD-ROMS AND SOFTWARE. . . . . . . . . . . . . . . . . . . . 2 • SOFTWARE CD-ROM . . . . . . . . . . . . . . . . . . . . . . 2 • OTHER CD-ROMS . . . . . . . . . . . . . . . . . . . . . . . . . 3 VERIFYING SYSTEM REQUIREMENTS . . . . . . . . . . . 4 • SYSTEM REQUIREMENTS . . . . . . . . . . . . . . . . . . 4 • SOFTWARE REQUIREMENTS . . . . . . . . . . . . . . . 5 3 SETUP IN A MACINTOSH ENVIRONMENT MAC OS X . . . . . . . . . . . . . . . . . . . . . . . .
1 BEFORE INSTALLING THE SOFTWARE This chapter describes the software programs that allow you to use the printer and scanner functions of the machine, the CD-ROMs that contain the software, and the pages where the installation procedures can be found. CD-ROMS AND SOFTWARE The software that can be used with the machine is on the CD-ROMs that accompany the machine and the expansion kits.
CD-ROMS AND SOFTWARE Disc 2 Software for Windows • PC-Fax driver (When the fax option is installed.) This enables you to send a file from your computer as a fax using the same procedure as when printing the file. Even if the fax function is not installed, the PC-Fax driver can be updated using the CD-ROM in the Internet fax expansion kit to enable you to send a file from your computer as an Internet fax in the same way as you print a file.
VERIFYING SYSTEM REQUIREMENTS SYSTEM REQUIREMENTS Before installing the software described in this manual, make sure that your computer satisfies the following requirements. Windows Macintosh*6 Operating system*1 Windows XP*3, Windows Server 2003*3, Windows Vista*3, Windows Server 2008*3, Windows 7*3, Windows 8*3, Windows Server 2012 Mac OS X 10.4 series, Mac OS X 10.5 series, Mac OS X 10.6 series, Mac OS X 10.7 series, Mac OS X 10.
VERIFYING SYSTEM REQUIREMENTS SOFTWARE REQUIREMENTS The following requirements must be met to use the software described in this manual. Operating system environment*1 Windows Software Required expansion kits Type of connection*1 PCL6 printer driver PS printer driver, PPD driver PC-Fax driver*2 Can be used in the standard configuration. Network/ USB Facsimile expansion kit*3,*4 Scanner driver Printer Status Monitor Macintosh Can be used in the standard configuration.
CONNECTING THE MACHINE CONNECTING TO A NETWORK To connect the machine to a network, connect the LAN cable to the machine's network connector. Use a shielded LAN cable. After connecting the machine to a network, be sure to configure the IP address and other network settings before installing the software. (The factory default setting for the IP address is to receive the IP address automatically when the machine is used in a DHCP environment.
2 SETUP IN A WINDOWS ENVIRONMENT This section explains how to install the software and configure settings so that the printer and scanner function of the machine can be used with a Windows computer. OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE) 1 Insert the "Software CD-ROM" into your computer's CD-ROM drive. 4 • If you are installing the printer driver or printer status monitor, insert the "Software CD-ROM" that shows "Disc 1" on the front of the CD-ROM.
OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE) 6 The software selection screen appears. Before installing the software, be sure to click the [Display Readme] button and view the detailed information on the software. * The above screen appears when using the "Disc 1" CD-ROM. For the steps that follow, see the appropriate page below for the software that you are installing.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER To install the printer driver or the PC-Fax driver, follow the appropriate procedure in this section depending on whether the machine is connected to a network or connected by USB cable. ☞ WHEN THE MACHINE WILL BE CONNECTED WITH A USB CABLE (page 19) * Depending on the models, PC-Fax driver may not be available.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER X Standard installation When the software selection screen appears in step 6 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 7), perform the steps below. With the standard installation, the PCL printer driver is installed. If you wish to select the printer driver to be installed, use the advanced installation procedure (page 12). 1 Click the [Printer Driver] button. 2 Click the [Standard installation] button.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER 3 Printers connected to the network are detected. Select the machine and click the [Next] button. 6 When the installation completed screen appears, click the [OK] button. 7 Click the [Close] button in the window of step 1. After the installation, a message prompting you to restart your computer may appear. If this message appears, click the [Yes] button to restart your computer.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER X Advanced installation When the software selection screen appears in step 6 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 7), perform the steps below. 1 Click the [Printer Driver] button. 3 To install the PC-Fax driver, click the [PC-Fax Driver] button on the "Disc 2" CD-ROM. • If the machine is not found, make sure that the machine is powered on and that the machine is connected to the network, and then click the [Re-search] button.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER 5 When the printer driver selection window appears, select the printer driver to be installed and click the [Next] button. 7 Proceed with the installation by following instructions from step 5 of "Standard installation" (page 11). Click the checkbox of the printer driver to be installed so that a checkmark ( ) appears. When the PC-Fax driver is being installed, this screen does not appear. Go to the next step.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER X Installation by specifying the machine's address When the machine cannot be found because it is not powered on or otherwise, installation is possible by entering the name (host name) or IP address of the machine. If the machine is being used on an IPv6 network, after you have installed the software as explained below, change the port as explained in "Changing to a Standard TCP/IP Port" (page 31).
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER 5 6 When the model selection window appears, select the model name of your machine and click the [Next] button. When the printer driver selection window appears, select the printer driver to be installed and click the [Next] button. 8 When the printer name window appears, click the [Next] button. If you wish to change the printer name, enter the desired name.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER 11 When the installation completed screen appears, click the [OK] button. 12 Click the [Close] button in the window of step 1. After the installation, a message prompting you to restart your computer may appear. If this message appears, click the [Yes] button to restart your computer. This completes the installation.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER X Printing using the IPP function and the SSL function The IPP function can be used to print to the machine over a network using HTTP protocol. When the machine is in a remote location, this function can be used in place of the fax function to print a higher quality image than a fax. The IPP function can also be used in combination with the SSL (encrypted communication) function to encrypt the print data.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER 5 Enter the machine's URL and click the [Next] button. Enter the URL in the following format: Normal format: http://:631*1/ipp *1 Normally "631" should be entered for the port number. If the IPP port number has been changed on the machine, enter the new port number.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER WHEN THE MACHINE WILL BE CONNECTED WITH A USB CABLE Supported operating systems: Windows XP/Server 2003/Vista/Server 2008/7/8/Server 2012 Administrator's rights are required to install the software. • Make sure that a USB cable is not connected to your computer and the machine. If a cable is connected, a Plug and Play window will appear. If this happens, click the [Cancel] button to close the window and disconnect the cable.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER 5 Follow the on-screen instructions. Read the message in the window that appears and click the [Next] button. When the installation completed screen appears, click the [OK] button. • If you are using Windows Vista/Server 2008/7/8 /Server 2012 If a security warning window appears, be sure to click [Install this driver software anyway].
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER When installing the PS printer driver, PPD driver, or PC-Fax driver Installation is possible even after the USB cable has been connected. When the software selection screen appears in step 6 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 7), perform the steps below. 1 Click the [Printer Driver] button. 3 When you are asked how the printer is connected, select [Connected to this computer] and click the [Next] button.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER 5 When the printer driver selection window appears, remove the [PCL6] checkmark and select the printer driver to be installed, and then click the [Next] button. 9 Follow the on-screen instructions. Read the message in the window that appears and click the [Next] button. Installation begins. • If you are using Windows Vista/Server 2008/7/8 /Server 2012 If a security warning window appears, be sure to click [Install this driver software anyway].
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER USING THE MACHINE AS A SHARED PRINTER If you are going to use the machine as a shared printer on a Windows network with the printer driver or the PC-Fax driver installed on a print server, follow the steps below to install the printer driver or the PC-Fax driver on the client computers. • Ask your network administrator for the server name and printer name of the machine on the network.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER CONFIGURING THE PRINTER DRIVER FOR THE OPTIONS INSTALLED ON THE MACHINE After installing the printer driver, you must configure the printer driver settings appropriately for the options that have been installed and the size and type of paper loaded in the machine. Follow the steps below to configure the printer driver. If the PPD driver is installed, see "When the PPD driver is installed" (page 26).
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER If automatic configuration fails • You can check the options that are installed and the tray settings by printing out the "All Custom Setting List" in the system settings of the machine. (However, note that "Input Tray Options" must be set to the number of trays on the machine.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER X When the PPD driver is installed 1 Click the [Start] button ( ), click [Control Panel], and then click [View devices and printers]. • In Windows XP/Server 2003, click the [start] button and then click [Printers and Faxes]. • For Windows 8, right-click in the Start screen (or swipe upward from the bottom edge), then click the App Bar ➞ [All apps] ➞ [Control Panel] ➞ [Hardware and Sound] ➞ [Devices and Printers] ➞ [Printers].
INSTALLING THE PRINTER STATUS MONITOR Printer Status Monitor is a printer utility that allows general users to check the current status of the machine on their computer screen, such as whether or not the machine is ready to print. The Printer Status Monitor shows error information such as paper misfeeds, printer configuration information (whether or not a finisher is installed, etc.) as an image, the paper sizes that can be used, and the amount of paper remaining.
INSTALLING THE SCANNER DRIVER The scanner driver (TWAIN driver) can only be used when the machine is connected to a network. When the scanner driver is installed, PC scan mode of the image send function can be used. Supported operating systems: Windows XP/Server 2003/Vista/Server 2008/7/8/Server 2012 Administrator's rights are required to install the software. After performing step 1 through step 5 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 7), continue the steps below.
INSTALLING THE SCANNER DRIVER 7 Select the IP address of the machine from the "Address" menu and click the [OK] button. • Be sure to ask your system administrator (network administrator) for the IP address of the machine. • The name (host name) or IP address of the machine can be directly entered in "Address". • If the port number used by the scanner function of the machine has been changed, enter a colon ":" following the IP address and then enter the port number.
CHANGING THE PORT When using the machine in a Windows environment, follow the steps below to change the port when you have changed the IP address of the machine or have installed the PC-Fax driver when the machine is connected with a USB cable. If the machine is being used on an IPv6 network, follow the steps 1 to 3 below and see "Changing to a Standard TCP/IP Port" (page 31) for the remaining steps of the procedure to change the port.
CHANGING THE PORT 4 Select [SC2 TCP/IP Port] and then click the [New Port] button. 5 • The "SC2 TCP/IP Port" is added when the printer driver is installed using a "Custom installation" with "LPR Direct Print (Specify Address/Auto Search)" selected. • If the printer driver is installed using a "Custom installation" with "IPP" selected, the [SC-Print2005 Port] is added.
CHANGING THE PORT 3 Click the [Next] button. 4 Enter the machine's IPv6 address in [Printer Name or IP Address] and click the [Next] button. 6 Configure the port settings. (2) (3) (1) (1) Select [LPR]. 5 (2) Enter [lp]. Select [Custom] and click the [Settings] button. (3) Click the [OK] button. 7 Click the [Next] button in the screen of step 5. 8 Click the [Finish] button. 9 Click the [Close] button in the screen of step 2.
3 SETUP IN A MACINTOSH ENVIRONMENT This chapter explains how to install the PPD file to enable printing from a Macintosh and how to configure the printer driver settings. ☞ MAC OS X: this page (10.4 / 10.5 / 10.6 / 10.7 / 10.8) • The printer expansion kit and PS3 expansion kit are required to use the machine as a printer in a Macintosh environment. In addition, the machine must be connected to a network. A USB connection cannot be used.
MAC OS X 7 The License Agreement window will appear. Make sure that you understand the contents of the license agreement and then click the [Continue] button. A message will appear asking you if you agree to the terms of the license. Click the [Agree] button. If the license appears in the different language, change the language in the language menu. 8 Select the hard drive where the PPD file will be installed and click the [Continue] button.
MAC OS X + 14 Configure thlr driver. • The machine can print using the IPP function. If you wish to use the IPP function, see "Printing using the IPP function" (page 37) to configure the printer driver settings. (3) Make sure that the PPD file of your model is selected. (1) (2) (3) The PPD file of the machine is automatically selected. (4) Click the [Add] button.
MAC OS X 15 Display printer information. (2) (1) (1) Click the machine's name. If you are using Mac OS X 10.5 / 10.6 / 10.7 / 10.8, click the [Options & Supplies] button, click the [Driver] tab and go to step 16. (2) Click [Show Info]. 16 Select the machine configuration. If you selected [Auto Select] in (3) of step 14, the machine configuration is detected and automatically configured. Check the configured settings to make sure they are correct. (1) Select [Installable Options].
MAC OS X X Printing using the IPP function The machine can print using the IPP function. When the machine is in a remote location, this function can be used in place of the fax function to print a higher quality image than a fax. If you wish to use the IPP function, follow these steps to select the PPD file when configuring the printer driver (step 14 on page 35). (1) (2) (3) (4) (1) Click the [IP Printer] icon. If you are using Mac OS X 10.5 / 10.6 / 10.7 / 10.8, click the [IP] icon.
4 TROUBLESHOOTING WHEN INSTALLATION WAS NOT SUCCESSFUL This section provides solutions to possible installation problems. See the following table of contents to locate the appropriate page for your question or problem. • The software cannot be installed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 • The machine is not detected (when connected to a network). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WHEN INSTALLATION WAS NOT SUCCESSFUL Problem The machine is not detected (when connected to a network). The plug and play screen does not appear (USB connection in Windows). Point to check Solution Is the machine power on? If the machine is powered off, it will not be detected. Switch on the main power switch and the [POWER] key ( ) in that order. (In Windows, search again after powering on the machine.
WHEN INSTALLATION WAS NOT SUCCESSFUL X The printer driver cannot be installed (Windows XP/Server 2003) If the printer driver cannot be installed on Windows XP/Server 2003, follow the steps below to check your computer settings. 1 Click the [start] button and then click [Control Panel]. 2 Click [Performance and Maintenance] and then [System]. 3 Click the [Hardware] tab and then the [Driver Signing] button. 4 Check the settings in "What action do you want Windows to take?".
REMOVING THE SOFTWARE To remove the printer driver or software installed using the installer, follow the steps below. Windows Mac OS X 1 1 Click the [start] button and then click [Control Panel]. To show the printer list, see step 11 and 12 of "MAC OS X" (page 33). For Windows 8, right-click in the Start screen (or swipe upward from the bottom edge), then click the App Bar ➞ [All apps] ➞ [Control Panel]. 2 2 Click [Uninstall a program]. Select the program or driver that you wish to delete.
Software Setup Guide SSG-ALL-EX-Z1
