Addendum to the Sharp Limited Servicer Maintenance Manual Including models: PG-D100U XG-E1200U XG-E3000U XG-E3500U XG-NV1U XG-NV2U XG-NV3XU XG-NV3XB XG-NV4SU XG-NV5XU XG-NV6XU XG-NV7XU XV-C10U XV-C10U(P) XV-H37VUA Ver.
Table of Contents Subject Convergence PG-D100U, XG-E1200U, XG-E3000U, XG-E3500U, XG-NV1U, XG-NV2U, XG-NV3XU, XG-NV3XB XG-NV4SU, XG-NV5XU XG-NV6XU Page 1-1 1-4 1-7 Lamp Replacement PG-D100U, XG-NV1U XG-E1200U, XG-E3000U, XG-E3500U XG-NV2U, XG-NV3XU, XG-NV3XB XG-NV4SU, XG-NV5XU XG-NV6XU XG-NV7XU XV-C10U, XV-C10U(P) 2-1 2-3 2-5 2-7 2-9 2-11 2-13 Filter / Cleaning / Replacement PG-D100U, XG-NV1U XG-E1200U, XG-E3000U, XG-E3500U XG-NV2U, XG-NV3XU, XG-NV3XB XG-NV4SU, XG-NV5XU, XG-NV6XU XV-C10U, XV-C10U(P) 3-
HOW TO CONVERGE THE LCD PANELS For the models XG-NV1U, XG-E1200U, PG-D100U, XG-E3000U, XG-NV2U, XG-NV3XU, XG-NV3XB, and XG-E3500U Tools and equipment needed: • Pattern Generator that can produce a crosshatch pattern (grid pattern) • Eccentric Cam Adjustment Wrench. (Sharp Part # 9DASPN-XGNV1U) • L-shaped Hex Wrench (Sharp part # 9EQLNC-XGNV1U) • Philips Screwdriver NOTE: Confirm focus before performing the convergence procedure.
HOW TO CONVERGE THE LCD PANELS (continued) Step Procedure Ref. # 2. Removal of body panels. 1. To remove the cabinet, refer to the service manual for the specific model. 3. Adjustment of the blue panel. 1. Supply the projector with a blue and green crosshatch signal from the pattern generator (on most video signal generators, it is possible to remove one or more of the 3 colors making up the crosshatch signal. In this case red must be removed.
Step Procedure 4. Adjustment of the red panel 1. Supply the projector with a red and green crosshatch signal from the pattern generator (turn blue off and red on). 2. Repeat same adjustment procedure as the blue panel. Convergence adjustment is complete. Y Direction Adjustment (Up & Down) X Direction Adjustment (Side To Side) Lock Screw θ Direction Adjustment (Tilt) Lock Screw fig. 1 Ver.
HOW TO CONVERGE THE LCD PANELS For the models XG-NV4SU and XG-NV5XU Tools and equipment needed: • • • • • Pattern Generator that can produce a crosshatch pattern (grid pattern) Eccentric Cam Adjustment Wrench. (Sharp Part # 9DASPN-XGNV1U) 2mm Hex Wrench (Sharp part # 9EQLNC-XGNV4U) 1.27mm Hex Wrench (available at most hardware stores) Philips Screwdriver NOTE: Confirm focus before convergence procedure.
HOW TO CONVERGE THE LCD PANELS (continued) Step Procedure Ref. # 2. Removal of body panels. 1. To remove the cabinet, refer to the service manual for the specific model. 3. Adjustment of the blue panel. 1. Supply the projector with a blue and green crosshatch signal from the pattern generator (on most video signal generators, it is possible to remove one or more of the 3 colors making up the crosshatch signal. In this case red must be removed.
fig. 2-1 Y Direction Adj. (1.27mm Hex) fig. 2-2 Ver.
HOW TO CONVERGE THE LCD PANELS For the model XG-NV6XU Tools and equipment needed: • • • • • Pattern Generator that can produce a crosshatch pattern (grid pattern) Eccentric Cam Adjustment Wrench. (Sharp Part # 9DASPN-XGNV1U) 2mm Hex Wrench (Sharp part # 9EQLNC-XGNV1U) 1.27mm Hex Wrench (available at most hardware stores) Philips Screwdriver NOTE: Confirm focus before convergence procedure.
Continued on next page. HOW TO CONVERGE THE LCD PANELS (continued) Step Procedure Ref. # 2. Removal of body panels. 1. To remove the cabinet, refer to the service manual for the specific model. 3. Adjustment of the blue panel. 1. Supply the projector with a blue and green crosshatch signal from the pattern generator (on most video signal generators, it is possible to remove one or more of the 3 colors making up the crosshatch signal. In this case red must be removed.
X Direction Adjustment Y Direction Adjustment θ Direction Adjustment Lock Screw "D" Lock Screw "D" R,B Adjusting Plate fig. 2-3 Ver.
HOW TO CHANGE THE LAMP ASSEMBLY For The Models PG-D100U and XG-NV1U Step Procedure Ref. # 1. Removal of the old Lamp Assembly. Refer to safety notes on page S-1 in the Main Limited Servicer Maintenance Manual before attempting to change the lamp 1. Remove the lamp cover. fig. 3 2. Remove the screws securing the lamp assembly. fig. 3 3. Pull the lamp assembly out of the projector. fig. 3 Safety notes: Be sure to wear Safety Glasses when removing the lamp.
Lamp Cover Lamp Assembly fig. 3 Ver.
HOW TO CHANGE THE LAMP ASSEMBLY For the models XG-E1200U, XG-E3000U, and XG-E3500U Step Procedure Ref. # 1. Removal of the old Lamp Assembly. Refer to safety notes on page S-1 in the Main Limited Servicer Maintenance Manual before attempting to change the lamp 1. Remove the lamp cover. fig. 4 2. Remove the screws securing the lamp assembly. fig. 4 3. Pull the lamp assembly out of the projector. fig. 4 Safety notes: Be sure to wear Safety Glasses when removing the lamp.
Lamp Assembly Lamp Cover fig. 4 Ver.
HOW TO CHANGE THE LAMP ASSEMBLY For the models XG-NV2U, XG-NV3XU, and XG-NV3XB Step Procedure Ref. # 1. Removal of the old Lamp Assembly. Refer to safety notes on page S-1 in the Main Limited Servicer Maintenance Manual before attempting to change the lamp 1. Remove the lamp cover. fig. 5 2. Remove the screws securing the lamp assembly. fig. 5 3. Pull the lamp assembly out of the projector. fig. 5 Safety notes: Be sure to wear Safety Glasses when removing the lamp.
Lamp Cover Lamp Assembly fig. 5 Ver.
HOW TO CHANGE THE LAMP ASSEMBLY For the models XG-NV4SU and XG-NV5XU Step Procedure Ref. # 1. Removal of the old Lamp Assembly. Refer to safety notes on page S-1 in the Main Limited Servicer Maintenance Manual before attempting to change the lamp fig. 6 1. Remove the lamp cover. 2. Remove the screws securing the lamp assembly. 3. Pull the lamp assembly out of the projector. fig. 6 fig. 6 Safety notes: Be sure to wear Safety Glasses when removing the lamp.
fig. 6 Lamp Assembly Lamp Cover fig. 6 Ver.
HOW TO CHANGE THE LAMP ASSEMBLY For the model XG-NV6XU Step Procedure Ref. # 1. Removal of the old lamp assembly. Refer to safety notes on page S-1 in the Main Limited Servicer Maintenance Manual before attempting to change the lamp fig. 6-1 1. Remove the lamp cover. 2. Remove the three screws securing the lamp assembly. 3. Pull the lamp assembly out of the projector. fig. 6-1 fig. 6-1 Safety notes: Be sure to wear Safety Glasses when removing the lamp.
Lamp Unit Fig. 6 Lamp Cover fig. 6-1 Ver.
HOW TO CHANGE THE LAMP ASSEMBLY For the model XG-NV7XU Step Procedure Ref. # 1. Removal of the old Lamp Assembly. Refer to safety notes on page S-1 in the Main Limited Servicer Maintenance Manual before attempting to change the lamp fig. 6-2 1. Remove the Lamp Cover. 2. Remove the three screws securing the lamp assembly. 3. Pull the lamp assembly out of the projector. fig. 6-2 fig.
Lamp Unit Lamp Cover fig. 6-2 Fig. 6-1 Ver.
HOW TO CHANGE THE LAMP ASSEMBLY For the model XV-C10U and XV-C10U(P) Step Procedure Ref. # 1. Removal of the old Lamp Assembly. Refer to safety notes on page S-1 in the Main Limited Servicer Maintenance Manual before attempting to change the lamp 1. Remove the lamp cover. fig. 7 2. Remove the two screws securing the lamp assembly. fig. 7 3. Pull the lamp assembly out of the projector. fig. 7 Safety notes: Be sure to wear Safety Glasses when removing the lamp.
Lamp Cage Cover Lamp Assembly fig. 7 Ver.
HOW TO CLEAN OR REPLACE AIR FILTER For the Models PG-D100U and XG-NV1U Step Procedure Ref. # 1. Removal of the Filter Cover. 1. To remove the fan cover, refer to the service manual for the specific model. The fan cover will either slide out or snap into place from the unit. 2. Removal of the Filter. 1. Separate the plastic filter cover from the fan cover by slightly flexing the fixed retaining tabs away from the inner perimeter of the fan cover, remove filter. 3. Inspecting the Filter. 1.
Press the arrow mark on the air filter cover and pull straight out. Grasp the air filter between your fingers and lift it out of the filter cover. POWER indicator goes off. Unplug the power cord. Clean the dust off the air filter and cover with a vacuum cleaner. Place the filter underneath the tabs on the filter frame. Return the air filter to its original position in the filter cover.
HOW TO CLEAN OR REPLACE AIR FILTER For the Models XG-E1200U, XG-E3000U, and XG-E3500U Step Procedure Ref. # 1. Removal of the Filter Cover. 1. To remove the fan cover, refer to the service manual for the specific model. The fan cover will either slide out or snap into place from the unit. 2. Removal of the Filter. 1. Separate the plastic filter cover from the fan cover by slightly flexing the fixed retaining tabs away from the inner perimeter of the fan cover, remove filter. 3. Inspecting the Filter.
• The air filter should be cleaned every 100 hours of use. Clean the filter more often when the projector is used in a dusty or smoky location. • Have your nearest Authorized Sharp Industrial LCD Products Dealer or Service Center exchange the filter (PFILD0055CEZZ) when it is no longer possible to clean it. Press the tab in the direction of the arrow and lift open the filter cover. Grasp the air filter between your fingers and lift it out of the filter cover. Turn off the MAIN POWER switch.
HOW TO CLEAN OR REPLACE AIR FILTER For the Models XG-NV2U, XG-NV3XU, and XG-NV3XB Step Procedure Ref. # 1. Removal of the Filter Cover. 1. To remove the fan cover, refer to the service manual for the specific model. The fan cover will either slide out or snap into place from the unit. 2. Removal of the Filter. 1. Separate the plastic filter cover from the fan cover by slightly flexing the fixed retaining tabs away from the inner perimeter of the fan cover, remove filter. 3. Inspecting the Filter. 1.
• The air filter should be cleaned every 100 hours of use. Clean the filter more often when the projector is used in a dusty or smoky location. • Have your nearest Authorized Sharp Industrial LCD Products Dealer or Service Center exchange the filter (PFILD0059CEZZ) when it is no longer possible to clean it. Press the tab in the direction of the arrow and lift open the filter cover. Grasp the air filter between your fingers and lift out the filter cover.
HOW TO CLEAN OR REPLACE AIR FILTER For the Models XG-NV4SU, XG-NV5XU and XG-NV6XU Step Procedure Ref. # 1. Removal of the Filter Cover. 1. To remove the fan cover, refer to the service manual for the specific model. The fan cover will either slide out or snap into place from the unit. 2. Removal of the Filter. 1. Separate the plastic filter cover from the fan cover by slightly flexing the fixed retaining tabs away from the inner perimeter of the fan cover, remove filter. 3. Inspecting the Filter. 1.
Press the tab in the direction of the arrow and lift open the filter cover. Grasp the air filter between your fingers and lift out the filter cover. Place the filter underneath the tabs on the filter frame. Return the air filter to its original position in the filter cover opening. Insert the tab on the end of the cover into the filter cover opening and press the filter cover into position. POWER indicator goes off. Unplug the power cord.
HOW TO CLEAN OR REPLACE AIR FILTER For the Model XV-C10U and XV-C10U(P) Step Procedure Ref. # 1. Removal of the Filter Cover. 1. To remove the fan cover, refer to the service manual for the specific model. The fan cover will either slide out or snap into place from the unit. 2. Removal of the Filter. 1. Separate the plastic filter cover from the fan cover by slightly flexing the fixed retaining tabs away from the inner perimeter of the fan cover, remove filter. 3. Inspecting the Filter. 1.
Remove Filter From Fan Cover & And Clean Fan Cover fig. 12 Ver.
HOW TO CLEAN THE LCD PANELS For the Model XV-C10U Tools and equipment needed: • Philips screw driver • Dry lens cleaning tissue, bleached cotton cloth, or lens brush Step 1. Removing the necessary Body Panels. Procedure Refer to safety notes on page S-1 in the Main Limited Servicer Maintenance Manual before attempting to clean the panels. Ref. # 1. To remove the Body Panel, first remove the Upper Cabinet Body to gain access to the components. ( Refer to the specific service manual.) 2.
fig. 13 Ver.
