Introduction MODEL PG-F261X PG-F211X Quick Start DATA PROJECTOR Setup OPERATION MANUAL Connections Basic Operation Useful Features Appendix
IMPORTANT • For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information. • Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 10. Model No.: Serial No.: SPECIAL NOTE FOR USERS IN THE U.K.
Introduction Introduction Before using the projector, please read this operation manual carefully. ENGLISH There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. 1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase. 2.
INFORMATION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications.
Introduction How to Read this Operation Manual ■ The specifications are slightly different, depending on the model. However, you can connect and operate all models in the same manner. • In this operation manual, the illustration and the screen display are simplified for explanation, and may differ slightly from the actual display.
Contents Preparing Introduction Setup How to Read this Operation Manual .... 3 Contents ............................................... 4 IMPORTANT SAFEGUARDS ............... 6 How to Access the PDF Operation Manuals .............................................. 9 Accessories ........................................ 10 Part Names and Functions ................. 11 Setting up the Projector ...................... 18 Inserting the Batteries .......................... 14 Usable Range ......................
Introduction Reference Appendix Maintenance ....................................... 47 Maintenance Indicators ...................... 48 Regarding the Lamp ........................... 50 Lamp ..................................................... 50 Caution Concerning the Lamp ............ 50 Replacing the Lamp ............................. 50 Removing and Installing the Lamp Unit .................................... 51 Resetting the Lamp Timer .................... 52 Connecting Pin Assignments ............
IMPORTANT SAFEGUARDS CAUTION: Please read all of these instructions before you operate this product and save these instructions for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing. 1.
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 16. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 17.
Observe the following safeguards when setting up your projector. Caution concerning the lamp unit ■ Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for replacement. See “Replacing the Lamp” on page 50.
Using the projector in other countries ■ If you are not to use the projector for a long time or before moving the projector, make certain you unplug the power cord from the wall outlet, and disconnect any other cables connected to it. ■ If the power cord is unplugged while the cooling fan is running, some parts of the projector may still be hot. Use caution when handling the projector. ■ Do not carry the projector by holding the lens.
Accessories Supplied accessories Two R-6 batteries RGB cable Lens cap (attached) (“AA” size, UM/SUM-3, (10' (3.0 m)) HP-7 or similar) Remote control Power cord (6' (1.8 m)) DIN-D-sub RS-232C adaptor (5 57/64" (15 cm)) Storage case • Operation manual (this manual and CD-ROM ) Note • Codes in “< >” are Replacement parts codes.
Numbers in Z refer to the main pages in this operation manual where the topic is explained. Projector Top View Power indicator 25, 48 STANDBY/ON button For turning the power on and putting the projector into standby mode. 25 ENTER button For setting items selected or adjusted on the menu. 37 25, 48 48 Temperature warning indicator 32 ECO+QUIET button For lowering the noise of the cooling fan and extending the lamp life. 29 VOL (Volume) buttons (–O/Q+) For adjusting the speaker sound level.
Part Names and Functions (Continued) Numbers in Z refer to the main pages in this operation manual where the topic is explained. Rear View Terminals AUDIO 1 input terminal 23 DVI-I input terminal Terminal for DVI digital, computer RGB, and component signals. 21 22 COMPUTER/ 21 COMPONENT input terminal 22 Terminal for computer RGB and component signals. AUDIO OUT 23 terminal Audio output terminal of equipment connected to the audio input terminal.
25 COMPUTER, DVI, S-VIDEO, VIDEO buttons For switching to the respective input modes. 29 BREAK TIMER button For displaying the break time. 32 Introduction STANDBY button For putting the projector into the standby mode. 25 ON button For turning the power on. 33 FREEZE button For freezing images. 29 AV MUTE button For temporarily displaying a black screen and turning off the sound.
Part Names and Functions (Continued) Inserting the Batteries 1 Pull down the tab on the cover and remove the cover towards the direction of the arrow. 2 Insert the batteries. 3 Insert the lower tab of the cover into the opening, and lower the cover until it clicks in place. • Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment. Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Introduction Usable Range Remote control sensor The remote control can be used to control the projector within the ranges shown in the illustration. Note • The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material. 30° When using the remote control • Ensure that you do not drop it or expose it to moisture or high temperature. • The remote control may malfunction under a fluorescent lamp.
Quick Start This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step. Setup and Projection In this section, connection of the projector and the computer is explained using one example.
4. Adjust the projected image with the Setup Guide 1 After the projector turns on, the Setup Guide appears. (When “Setup Guide” is set to “On”. See page 42.) 2 Follow the steps in the Setup Guide and adjust the focus, picture size, and height (angle). 3 After adjusting the focus, height (angle) and picture size, press ENTER to finish the Setup Guide. Quick Start _PP. 26, 27 5. Correct trapezoidal distortion Correcting trapezoidal distortion using Keystone Correction. On the projector Shrinks upper side.
Setting up the Projector Setting up the Projector For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. (See page 28.) Standard Setup (Front Projection) ■ Place the projector at the required distance from the screen according to the desired picture size. (See page 20.
Projection (PRJ) Mode The projector can use any of the 4 projection modes shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-ADJ” menu. See page 42.
Setting up the Projector (Continued) Screen Size and Projection Distance NORMAL Mode (4:3) Picture (Screen) size Diag. [χ ] Width Height Projection distance [L] Minimum [L1] Maximum [L2] Distance from the lens center to the bottom of the image [H] 300 (762 cm) 610 cm (240 ) 457 cm (180 ) 11.2 m (36 10 ) — 19 cm (7 9/16 ) 270 (686 cm) 549 cm (216 ) 411 cm (162 ) 10.1 m (33 2 ) 11.7 m (38 4 ) 17 cm (6 51/64 ) 250 (635 cm) 508 cm (200 ) 381 cm (150 ) 9.4 m (30 9 ) 10.
Connecting the Projector to Other Equipment Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off the equipment to be connected. After making all connections, turn on the projector and then the other pieces of equipment. When connecting a computer, ensure that it is the last equipment to be turned on after all the connections are made.
Connecting the Projector to Other Equipment (Continued) Equipment Video equipment Terminal on Cable connected equipment HDMI to DVI cable HDMI (commercially available) output terminal DVI digital output terminal Terminal on the projector DVI-I DVI Digital cable (commercially available) 3 RCA to mini D-sub 15 pin cable (optional, AN-C3CP2) COMPUTER/ COMPONENT S-video output terminal S-video cable (commercially available) S-VIDEO Video output terminal Video cable (commercially available) VIDEO C
Equipment Audio equipment Terminal on connected equipment Cable ø3.5 mm stereo or mono audio cable ø3.5 mm audio output (commercially available or available as Sharp service part QCNWGA038WJPZ) terminal RCA audio output terminal Terminal on the projector AUDIO 1 RCA audio cable (commercially available) AUDIO 2 Cables for a camera or a video game Audio output terminal Monitor RGB input terminal ø3.5 mm audio input terminal RCA audio input terminal MONITOR OUT ø3.
Controlling the Projector by a Computer When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS232C adaptor and an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector. See page 56 for details.
Turning the Projector On/Off Info Turning the Projector on Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages 21 to 24.) Remove the lens cap and press STANDBY/ON on the projector or ON on the remote control.
Image Projection Setup Guide screen About the Setup Guide After turning on the projector, the Setup Guide screen appears to assist you with projector setup. Guidance items 1 FOCUS 2 HEIGHT ADJUST 3 ZOOM Press ENTER to exit the Setup Guide screen. Note • The Setup Guide screen automatically highlights the items in the following order: 1 FOCUS 4 ENTER 2 HEIGHT ADJUST 3 ZOOM However, you can adjust the focus, height (angle), or zoom regardless of the highlighted item.
3 Adjusting the Height The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector. When the screen is above the projector, the projection image can be made higher by adjusting the projector. 1 Lift the projector to adjust its height while lifting the HEIGHT ADJUST lever. 2 Remove your hands from the HEIGHT ADJUST lever of the projector after its height has been finely adjusted. HEIGHT ADJUST lever • The angle of projection is adjustable up to approx.
Image Projection (Continued) Correcting Trapezoidal Distortion Adjustment buttons (P/R/O/Q) When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction.
COMPUTER, DVI, S-VIDEO, VIDEO buttons Switching the Input Mode Select the appropriate input mode for the connected equipment. AV MUTE button Press COMPUTER, DVI, S-VIDEO or VIDEO on the remote control to select the input mode. VOL +/– (Volume) buttons • When you press INPUT on the projector or DVI on the remote control, the INPUT list appears. Press P/R to switch the INPUT mode. Adjusting the Volume Press VOL +/– on the remote control or –O/Q+ on the projector to adjust the volume.
Image Projection (Continued) Resize Mode This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose “NORMAL”, “BORDER” or “STRETCH” image. Press RESIZE. • See page 41 for setting on menu screen.
VIDEO • “STRETCH” is fixed when 540P, 720P, 1035I or 1080I signals are entered. Input Signal DVD / Video Output screen image Image type NORMAL STRETCH BORDER * * * * 4:3 aspect ratio 480I, 480P, 576I, 576P, NTSC, PAL, SECAM Letter box * Squeezed 16:9 image * Squeezed 4:3 image * * Basic Operation 16:9 aspect ratio 540P, 720P, 1035I, 1080I 16:9 aspect ratio (4:3 aspect ratio in 16:9) * Mode for projecting an image with the original aspect ratio without cutting any portions.
Operating with the Remote Control BREAK TIMER button POINTER button Displaying the Pointer 1 Press POINTER and press P/R/ O/Q on the remote control to move the pointer. 2 Press POINTER again. SPOT button • The pointer will disappear. Adjustment buttons (P/R/O/Q) ECO+QUIET button Displaying and Setting the Break Timer 1 Press SPOT and press P/R/O/Q on the remote control to move the spot area. 2 Press SPOT again. • The spot area will disappear. • The timer starts to count down from 5 minutes.
Selecting the Picture Mode FREEZE button You can select the appropriate picture mode for the projected image, such as movie or video game. Press PICTURE MODE. • When pressing PICTURE MODE, the picture mode changes in the following order: STANDARD PICTURE MODE button AUTO SYNC button PRESENTATION MOVIE GAME sRGB * Note • See page 39 for details on the picture mode. * “sRGB” is displayed only when RGB signal is input.
Operating with the Remote Control (Continued) Using the Remote Control as the Wireless Computer Mouse When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse. If the computer is placed too far away from the projector to be connected via the USB cable, the remote receiver (optional, AN-MR2) makes it possible to operate the projector with the remote control. For details, see the operation manual of the receiver.
Menu Items The following shows the items that can be set in the projector.
Menu Items (Continued) “Projector adjustment (PRJ-ADJ)” menu Picture SCR - ADJ PRJ - ADJ Auto Power Off Auto Restart STANDBY Mode System Sound Speaker Audio Input RS-232C Fan Mode System Lock Lamp Timer(Life) Help 0 h Main menu PRJ - ADJ On On Standard On On Audio 1 9600bps Normal Disable Page 43 Sub menu Auto Power Off [On/Off] Page 43 Auto Restart [On/Off] Page 43 STANDBY Mode Page 43 Standard Eco System Sound [On/Off] 0 min 100% Page 43 Speaker [On/Off] SEL./ADJ.
Using the Menu Screen ENTER button Adjustment buttons (P/R/O/Q) MENU/HELP button ENTER button Adjustment buttons (P/R/O/Q) RETURN button • Press RETURN to return to the previous screen when the menu is displayed. MENU/HELP button Menu Selections (Adjustments) Example: Adjusting “Bright”. • This operation can also be performed by using the buttons on the projector. 1 Press MENU/HELP. 2 Press Q or O and select “Picture” to adjust. • The “Picture” menu screen for the selected input mode is displayed.
Using the Menu Screen (Continued) 3 Press P or R and select “Bright” to adjust. • The selected item is highlighted. Picture SCR - ADJ PRJ - ADJ Picture Mode Contrast Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset SEL./ADJ. Help Standard 0 0 0 0 0 1 Bright Single ADJ END Items to be adjusted Picture To adjust the projected image while watching it SCR - ADJ Resize Image Shift Keystone OSD Display PRJ - ADJ Help Border 0 0 On Press ENTER. • The selected item (e.g.
Picture Adjustment (“Picture” Menu) Menu operation n Page 37 Q Example: “Picture” screen menu for COMPUTER (RGB) input Picture SCR - ADJ Picture Mode Contrast Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset SEL./ADJ. PRJ - ADJ Q Example: “Picture” screen menu for S-VIDEO input Help Picture 0 0 0 0 0 1 Bright ENTER SCR - ADJ Picture Mode Contrast Bright Color Tint Sharp CLR Temp Bright Boost Progressive Lamp Setting Reset Standard Help Standard 0 0 0 0 0 0 1 3D Progressive Bright SEL.
Picture Adjustment (“Picture” Menu) (Continued) Menu operation n Page 37 2 Adjusting the Image Adjustment items O button Q button 4 Progressive Selectable items Description Contrast For less contrast. For more contrast. 2D Useful to display fast-moving images Progressive such as sports. Bright For less brightness. For more brightness. Useful to display relatively slow3D Progressive moving images such as drama and documentary more clearly. Red*1 For weaker red. For stronger red.
Adjusting the Projected Image (“SCR - ADJ” Menu) Menu operation n Page 37 Picture 1 2 3 4 5 6 7 8 SCR - ADJ Resize Image Shift Keystone OSD Display Background Setup Guide PRJ Mode Language SEL./ADJ. 1 Setting the Resize Mode Note • For details of the Resize mode, see pages 30 and 31. • You can also press RESIZE on the remote control to set the resize mode. (See page 30.
Adjusting the Projected Image (“SCR - ADJ” Menu) (Continued) Menu operation n Page 37 4 Setting the On-screen Display Selectable items Description On All on-screen displays are displayed. Off INPUT/VOLUME/AV MUTE/FREEZE/ AUTO SYNC/RESIZE/PICTURE MODE/ “An invalid button has been pressed.” are not displayed.
Adjusting the Projector Function (“PRJ - ADJ” Menu) Menu operation n Page 37 Picture SCR - ADJ PRJ - ADJ Auto Power Off Auto Restart STANDBY Mode System Sound Speaker Audio Input RS-232C Fan Mode System Lock Lamp Timer(Life) SEL./ADJ. Help 3 STANDBY Mode On On Standard On On Audio 1 9600 bps Normal Disable 0 h When set to “Eco”, power consumption is reduced in standby mode.
Adjusting the Projector Function (“PRJ - ADJ” Menu) (Continued) Menu operation n Page 37 7 Selecting the Transmission Speed (RS-232C) Make sure that both the projector and computer are set for the same baud rate. Selectable items 9600bps Description 9 System Lock Function This function prevents unauthorized use of the projector. Once this function is activated, users must enter the correct keycode each time the projector is turned on.
4 Press the 4 buttons on the remote control or on the projector to enter the new keycode in “New Code”. Note • You cannot use the following buttons for keycode: • STANDBY/ON • ON • STANDBY • ENTER • L-CLICK • R-CLICK/RETURN • MENU/HELP • System lock function recognizes each button on the remote control or on the projector as an individual button, even if they share the same button name. If you used the buttons on the projector in setting your keycode, the keycode cannot be canceled with the remote control.
Troubleshooting with the “Help” Menu This function advises you to solve the problems during usage. Utilizing the “Help” Menu Functions ENTER button Adjustment buttons (P/R/O/Q) Example: When image flickering appears Operation to solve image flickering when projecting the computer RGB signal. 1 Press MENU/HELP. 2 Press O or Q to select “Help”, then press ENTER. 3 Press P or R to select “Vertical stripes or flickering image appears” on Help menu, then press ENTER.
Maintenance Cleaning the projector ■ Ensure that you have unplugged the power cord before cleaning the projector. ■ The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet. ■ Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods. The effects of some of the agents in the plastic may cause damage to the quality or finish of the projector.
Maintenance Indicators ■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector. ■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter standby mode. After the projector has entered standby mode, follow the procedures given below.
Maintenance indicator Temperature warning indicator Lamp indicator Power indicator Normal Abnormal Off Red on (Standby) Red on Problem The internal temperature is abnormally high. Cause • Blocked air intake • Relocate the projector to an area with proper ventilation. (See page 8.) • Cooling fan breakdown • Internal circuit failure • Clogged air intake • Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 64) for repair. The lamp does not illuminate.
Regarding the Lamp Lamp ■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (See page 44.) ■ Purchase a replacement lamp of type AN-XR30LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center. IMPORTANT NOTE TO U.S.
Removing and Installing the Lamp Unit Warning! • Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury. Lamp unit AN-XR30LP Optional accessory Info • Do not touch the glass surface of the lamp unit or the inside of the projector. • To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below. • Do not loosen other screws except for the lamp unit cover and lamp unit.
Regarding the Lamp (Continued) 4 Remove the lamp unit. 5 Insert the new lamp unit. 6 Replace the lamp unit cover. • Loosen the securing screws from the lamp unit. Hold the lamp unit and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it. • Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws. Securing screws • Align the tab on the lamp unit cover (1) and place it while pressing the tab (2) to close it.
Storing the Projector How to Use the Storage Case When storing the projector, attach the lens cap to the lens, and place it in the supplied storage case. 1 Open the cover of the storage case. 2 Place the projector into the storage case. Lens cap Info • Ensure the projector has cooled down sufficiently before placing it in the case. • Ensure the lens cap is attached to the lens for protection. • Place the projector into the storage case with the lens facing the handle.
Connecting Pin Assignments COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals:mini D-sub 15 pin female connector COMPUTER Input/Output COMPONENT Input/Output Pin No. Signal Pin No. Signal 1. Video input (red) 1. PR (CR) 2. Video input (green/sync on green) 2. Y 15 11 3. Video input (blue) 3. PB (CB) 4. Not connected 4. Not connected 5. Not connected 5. Not connected 6. Earth (red) 6. Earth (PR) 7. Earth (green/sync on green) 7. Earth (Y) 8. Earth (blue) 8. Earth (PB) 9. Not connected 9.
RS-232C Terminal: mini DIN 9 pin female connector 8 I/O Reference Name Pin No. Signal Not connected 1. 9 7 Receive Data Input Connected to internal circuit RD 2. Output Send Data Connected to internal circuit SD 3. Not connected 4. 6 3 5. Signal Ground Connected to internal circuit SG Not connected 6. Request to Send Connected to CS in internal circuit 7. RS 4 5 Clear to Send Connected to RS in internal circuit 8. CS Not connected 9.
RS-232C Specifications and Command Settings Computer control A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, sold separately) to the projector. (See page 24 for connection.) Communication conditions Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard.
Commands Example: When turning on the projector, make the following setting.
RS-232C Specifications and Command Settings (Continued) RETURN CONTROL CONTENTS Resize S-Video Video ALL Reset Computer INPUT Picture Mode Contrast Bright Red Blue Color Tint Sharp CLR Temp Bright Boost Progressive Picture Reset Signal Type Audio Input DVI INPUT Picture Mode Contrast Bright Red Blue Color Tint Sharp CLR Temp Bright Boost Progressive Picture Reset Signal Type COMMAND Normal Stretch Border Normal Stretch Border Standard Presentation Movie Game sRGB -30 – +30 -30 – +30 -30 – +30 -30
RETURN CONTROL CONTENTS S-Video INPUT Picture Mode Contrast Bright Color Tint Sharp CLR Temp Bright Boost Progressive Picture Reset Audio Input Video INPUT Picture Mode Contrast Bright Color Tint Sharp CLR Temp Bright Boost Progressive Picture Reset Audio Input -150 – +150 Clock -30 – +30 Phase -150 – +150 H-position -60 – +60 V-position Fine Sync Adjustment Reset -96 – +96 Image Shift On OSD Display Off Auto Video System PAL SECAM NTSC4.43 NTSC3.
RS-232C Specifications and Command Settings (Continued) RETURN CONTROL CONTENTS Auto Power Off Auto Restart STANDBY Mode PRJ Mode On Off On Off Standard Eco Reverse Invert Language English Deutsch Español Nederlands Français Italiano Svenska Português Setup Guide System Sound Internal Speaker RGB Frequency Check Fan Mode Lamp Timer Reset *3 60 polski Türkçe On Off On Off On Off Horizontal Vertical Normal High COMMAND On Off On Off A A A A M M I I I I M M M M M M M M M M M M M M M S S S S A A T T H
Computer Compatibility Chart Computer • Multiple signal support Horizontal Frequency: 15-70 kHz, Vertical Frequency: 45-85 Hz, Pixel Clock: 12-108 MHz Sync signal: Compatible with TTL level • Compatible with sync on green signal The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.
Troubleshooting Problem Check Projector power cord is not plugged into the wall outlet. Power to the external connected devices is off. The selected input mode is wrong. Cables are incorrectly connected to the projector. Remote control battery has run out. External output has not been set when connecting notebook computer. The lamp unit cover is not installed correctly.
Problem Maintenance indicator on the projector illuminates or blinks in red. The projector cannot be turned on or put into the standby mode using STANDBY/ON on the projector. Picture is green on COMPUTER (Component)/ DVI (Component). Picture is pink (no green) on COMPUTER (RGB)/ DVI (RGB). Picture is too bright and whitish. The cooling fan becomes noisy. The lamp does not light up even after the projector turns on. The lamp suddenly turns off during projection. The image sometimes flickers.
For SHARP Assistance If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 62 and 63. If this operation manual does not answer your question, please contact the SHARP Service departments listed below. U.S.A. Sharp Electronics Corporation 1-888-GO-SHARP (1-888-467-4277) lcdsupport@sharpsec.com http://www.sharpusa.com Canada Sharp Electronics of Canada Ltd. (905) 568-7140 http://www.sharp.
Specifications Model Display device Resolution Lens Input terminal Output terminal Control, others F number Zoom Focus DVI-I (Compatible with HDCP) RGB/Component (mini D-sub 15 pin) S-Video (mini DIN 4 pin) Video (RCA) Audio (ø3.5 mm stereo minijack) Audio (RCA) RGB/Component (mini D-sub 15 pin) Audio (ø3.
Dimensions 3 33/64 (89) 1 31/64 2 5/8 (66.35) (37.
Index Accessories ............................................................. AC socket ................................................................ Adjustment buttons ................................................. Aspect ratio ............................................................. Audio Input .............................................................. AUDIO 1, 2 terminal ................................................ AUDIO OUT terminal ..............................................
