PG-C30XU FINAL PDF SERVICE MANUAL S99O4XG-NV5XB LCD PROJECTOR MODEL PG-C30XU In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. CONTENTS Page • • • • • • • • • • • • SPECIFICATIONS ............................................. 2 IMPORTANT SERVICE SAFETY NOTES ......... 3 NOTE TO SERVICE PERSONNEL ................... 4 OPERATION MANUAL ......................
PG-C30XU Specifications Product type Model LCD Projector PG-C30XU Video system PAL/SECAM/NTSC 3.58/NTSC 4.43/DTV 480P/DTV 720P/DTV 1080I Display method LCD panel LCD panel × 3, RGB optical shutter method × 18.4 [W] mm) Panel size: 0.9" (13.8 [H] Display method: Translucent TN liquid crystal panel Drive method: TFT (Thin Film Transistor) Active Matrix panel × 768 [V]) × zoom lens, F1.7-2.0, f = 33-43 mm No. of dots: 786,432 dots (1,024 [H] Lens 1-1.
PG-C30XU IMPORTANT SERVICE SAFETY NOTES Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm per volt., or higher, sensitivity to measure the AC voltage drop across the resistor (See Diagram). » All checks must be repeated with the AC plug connection reversed.
PG-C30XU NOTE TO SERVICE PERSONNEL 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 NOTE POUR LE PERSONNEL D’ENTRETIEN 12345678901234567890123456789012123456789012345 UV-RADIATION PRECAUTION 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 PRECAUTION POUR LES RADIATIONS UV 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 The light source, metal halide lamp, in the
PG-C30XU 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 UV-RADIATION PRECAUTION (Continued) 1234567890123456789012345678901212345678901234 1234567890123456789012345678901212345678901234 1234567890123456789012345678901212345678901234 PRECAUTION POUR LES RADIATIONS UV
PG-C30XU WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. CAUTION The lighting flash with arrowhead within a triangle is intended to tell the user that parts inside the product are risk of electric shock to persons. RISK OF ELECTRIC SHOCK.
PG-C30XU Location of Controls Projector LAMP REPLACEMENT indicator MUTE button TEMPERATURE WARNING indicator POWER indicator VOLUME buttons (+/–) POWER buttons (ON/OFF) MENU button KEYSTONE button AUTO SYNC button INPUT button FREEZE button RESIZE button ENLARGE button GAMMA button BLACK SCREEN button UNDO button ADJUSTMENT buttons (' /" /\ /|) ENTER button Zoom knob Carrying handle Remote control sensor Kensington Security Standard connector Focus knob Foot release Front and Top View
PG-C30XU Operating the Wireless Mouse Remote Control Remote Control Front View Rear View MUTE button POWER buttons (ON/OFF) VOLUME buttons (+/–) KEYSTONE/BLACK SCREEN button LEFT-CLICK button LASER POINTER/ MENU button MOUSE/ ADJUSTMENT buttons (' / " / \ / | ) RIGHT-CLICK/ ENTER button UNDO button INPUT button AUTO SYNC button FREEZE button ENLARGE button RESIZE button TOOLS button GAMMA button MOUSE/ ADJUSTMENT switch BACKLIGHT button Top View Remote control signal transmitter Laser poi
PG-C30XU Using the Remote Control as a Wireless Mouse The remote control has the following three functions: • Projector control • Wireless mouse • Laser pointer MOUSE/ADJUSTMENT switch (Remote control) MOUSE ADJ. MOUSE Wireless mouse Laser pointer ADJ. Projector control Remote Control/Mouse Receiver Positioning • The remote control can be used to control the projector within the ranges shown below.
PG-C30XU Effective buttons in MOUSE mode Use as a Wireless Mouse Be sure the supplied remote mouse receiver is connected to your computer. Remote control (Front view) LASER POINTER (Slide the MOUSE/ADJUSTMENT switch on the remote control to the MOUSE position.) MOUSE ADJ. BLACK SCREEN MOUSE RIGHT-CLICK BACKLIGHT • The wireless mouse may not operate correctly if your computer serial port is not correctly set up.
PG-C30XU Connection Pin Assignments Analog Computer 1 and 2 Signal Input Ports: 15-pin mini D-sub female connector 1 6 11 5 10 15 Computer Input Analog 1. Video input (red) 2. Video input (green/sync on green ) 3. Video input (blue) 4. Reserve input 1 5. Composite sync 6. Earth (red) 7. Earth (green/sync on green) 8. Earth (blue) 9. 10. 11. 12. 13. 14. 15. Component Input 1. PR (CR) 2. Y 3. PB 4. Not connected 5. Not connected 6. Earth (PR) 7. Earth (Y) 8. Earth (PB) 9. Not connected 10.
PG-C30XU Dimensions /32 (23) 23 /64 (9) 3 51/64 (96.5) 105/16 (262) 147/64 (358.4) 1213/64 (310) 2 13/32 (61) 23/64 (9) 2 13/32 (61) 5 19/32 (142) 9 11/32 (237.5) 6 13/32 (163) 1 5/16 (33.5) 25/64 (10) 3 53/64 (97.5) 29 Top View 1 5/64 (27.5) Rear View /8 (16) 13 4 49/64 (121) /32 (10.5) 3 21/32 (93) Front View /32 (13) 7/16 (11) 17 1 13/16 (30) 3 17/64 (83) 9 1/64 (229) 63/64 (25) 3 17/64 (83) 5 9 19/32 (243.
PG-C30XU REMOVING OF MAJOR PARTS 1. Removing the Intake cover and lamp unit S H A R P 1-1. Detach the Intake cover. 1-2. Loosen the lamp cover screw and draw out the lamp cover in the direction of arrow (toward yourself). 1-3. Remove the two lamp unit lock screws. Detach the lamp unit. Lamp unit 1-3 1-3 1-2 Intake cover 1-1 Lamp cover Note: When replacing the lamp, make sure that there is a clearance of over 8mm between the terminal and the lamp snap-on spring (and other metallic parts).
PG-C30XU 2. Removing the top and rear cabinets 2-1. Remove the four rear cabinet lock screws. 2-2. Remove the four terminal board lock screws off the rear cabinet. Unhook and detach the rear cabinet from below. 2-3. Remove the four top cabinet lock screws from below. H S R A P Press both sides of the bottom cabinet in the directions of arrow to undo the hooks. Lift and detach the top cabinet. 2-1 2-3 Hook 2-2 2-4. Slowly lift the top cabinet and disconnect the operation key unit connector (KY).
PG-C30XU 3. Removing the PWB units 3-1. Disconnect the connectors from the output unit. 3-2. Remove the four PC I/F unit lock screws, and take out the PC I/F unit. 3-3. Remove the spacer (stud bolt) and the three screws off the output unit. Lift the output unit, together with the signal unit, off the position. 3-4. Remove the S-out/REG unit angle lock screw and take out the S-out/REG unit.
PG-C30XU 4. Removing the optical mechanism unit 4-1. Remove the six optical mechanism unit lock screws. Lift the unit off the position. 4-2. Remove the two lamp socket holder lock screws and take out the holder.
PG-C30XU 5. Removing the Power/Ballast unit assembly 5-1. Remove the Power/Ballast unit assembly lock screw. 5-2. Remove the (FG) lead lock screw. 5-3. Lift the Power/Ballast unit assembly off the position. 6. Removing the ballast unit and inlet unit 6-1. Disconnect the connector (PA) from the inlet unit. Take out the AC power switch. 6-2. Remove the Inlet unit lock screw. 6-3. Pull the inlet unit toward yourself off the position.
PG-C30XU RESETTING THE TOTAL LAMP TIMER When the lamp has been replaced, reset the total lamp timer in the following steps. Resetting procedure 1. While holding down the “ENTER”, “ADJ."” and “ADJ.|” keys on the set at the same time, turn on the main power switch (located side the AC inlet). 2. Now the total lamp timer is reset to zero. “000H” appears on the screen. LAMP POWER ON I TEMP.
PG-C30XU THE OPTICAL UNIT OUTLINE Layout of the optical system Note: Layout for positioning the optical system.
PG-C30XU CONVERGENCE AND FOCUS ADJUSTMENT » Start the convergence and focus adjustments with the top panel removed but the power on. Use the remote control to adjust the image. Take the following procedures. 1. Focusing the projection lens (A) Replacing all the 3 LCD panels 1. Before replacing all the 3 LCD panels, project an image on the screen and bring it into focus. 2. Replace the LCD panels with new ones.
PG-C30XU 4. With the G-LCD panel's screen center as refernce, adjust the R-LCD and B-LCD panels. 5. Finally tighten up the convergence lock screw "d". Notes : 1 The eccentric cam is used for convergence adjustment. This means that the cam's turning and the linear movement are not always uniform. 2 This model is not equipped with the LCD image adjustment mechanism. This is because the cross-dichroic prism is used for image formation.
PG-C30XU Convergence and Focus Adjustments at a Glance Adjustment directions Adjustment Direction X direction Convergence Y direction θZ direction Z direction Focus θX direction θY direction Definition Direction of LCD panel LCD right and left LCD top and bottom LCD turning axis LCD optical axis LCD top-to-bottom flapping LCD right-to-left flapping Rotation around Z axis Rotation around X axis Rotation around Y axis Convergence and Focus Adjustment for the Optical Mechanism Color Adjustment Converge
PG-C30XU Replacing the LCD panels Detach the top panel and the optical mechanism unit in advance. (1) Remove the four prism holder lock screws. Detach the prism holder from the optical mechanism unit. (2) Remove the LCD panel lock screws (four each for the R-, G- and B-LCD panels). Detach the LCD panels from the prism holder. (3) Mount a new LCD panel in the reverse order of the above steps (1) and (2). ~ Readjust the convergence and focus.
PG-C30XU Adjusting the optical axis of the mirrors (M1, M5 and M4/M6) The optical axis must be readjusted if an eclipse happens with the R. G or B mirrors. Generally speaking, this adjustment is needed when any of the internal optical components has been replaced. Adjustment procedure required when any of the panels has been replaced or the convergence has been adjusted (1) Disconnect the flat cables of all the LCD panels. (2) Let the lamp light up.
PG-C30XU ELECTRICAL ADJUSTMENT Hook up a signal generator, or a DOSV or Mac personal computer to the projector in order to feed the signals specified in the Adjusting conditions. No. Adjusting point Adjusting conditions Adjusting procedure 1 EEPROM initialization 1. Turn on the power (make sure the lamp lights up) and warm up the unit for 15 minutes. » Make the following settings: Press S5001 to call up the process mode and execute S2 in the SSS menu.
PG-C30XU No. 8 Adjusting point P SIGNAL Adjusting conditions Adjusting procedure 1. Connect the oscilloscope to TP1701 for red. TP1702 for green TP1703 for blue. » Adjust the PSIG waveform to the one shown below. (Adjust with PSIG-H.) PSIG 2. Make the following choice: Group : OUTPUT 2 Subject : PSIG-H : PSIG-L 7.3±0.2V DC 2.0V DC GND (Adjust with PSIG-L.) » For the green and blue colors, make sure their waveforms are similar to that of the red color.
PG-C30XU No. 11 12 Adjusting point RGB countervoltage adjustment RGB gradation regeneration adjustment Adjusting conditions Adjusting procedure 1. Feed the black-and-red (25%) stripe signal (XGA). 2. Make the following choice: Group : OUTPUT 3 Subject : RC (R) and Group : OUTPUT 3 Subject : RC-INV (R) » Using the control switches or the remote controller buttons, adjust the data in order to minimize the flicker. 1. Feed the green-only SMPTE pattern signal (XGA).
PG-C30XU No. Adjusting point Adjusting conditions Adjusting procedure 16 Video brightness adjustment 1. Feed the baseband (split color bar) signal. (The ONAIR signal is not accepted because of its too much noise.) Group : VIDEO 2 Subject : VROS/VGOS/VBOS 2. Press the control switch or the remote control’s mute button (to set the gamma correction to the process setting). » Using the control switches or the remote controller buttons, adjust the setting until the black signal becomes bit-less.
PG-C30XU No. Adjusting point Adjusting conditions Adjusting procedure 22 Video input panel signal amplitude adjustment 1. Feed the NTSC 10-step signal. 2. Select the following group and subject. Group: VIDEO2 Subject: R1-GAIN B1-GAIN 3. Connect the synchroscope to TP1101 (R) and TP1201 (G). 4. For the blue color, connect the synchroscope to TP1301 (B) and TP1201 (G). » Select R1-GAIN and adjust the setting so that the R and G signals have the same amplitude.
PG-C30XU No. Adjusting point Adjusting conditions 1. Receive the RGB signal. Adjusting procedure » In the process mode and select L4. Check the picture, brightness, red, blue, clock, phase, horizontal position, and vertical position. 30 RGB performance check 31 Off-timer performance check 32 Thermistor performance check 1. Heat the thermistor using a dryer. » Make sure the “TEMP” is displayed. 33 Automatic synchronization 1. Receive the PHASE check pattern signal.
PG-C30XU ADJUSTING THE PC BOARD (CPCi-0047CE01. PC I/F Unit) 1. Setting the oscilloscope Set the range to DC 1 V/div and 5µs/div. 2. Connecting the PC interface 1) Connect the PC interface to the projector. Make surethe CON2 (P8404), CON3 (P8502) and CON4 (P8405)connectors are all tight in position. 2) Connect the cable between the computer’s ANALOG OUTPUTterminal and the DSUB (INPUT1 on the projector)connector. 3) Set the projector’s input selector to the RGB1position.
PG-C30XU Servicing precautions (1) If the convergence gets out of spec in servicing the set, call the process mode and select the following group and subjects. Group: NOKO Subject: R-CNV-H, R-CNV-V G-CNV-H, G-CNV-V B-CNV-H, B-CNV-V (H and V are for horizontal and vertical adjustments, respectively.) Adjust the above settings to the range of 0 to 4. (2) When entering the process mode, select the following group and subjects too.
PG-C30XU TROUBLE SHOOTING TABLE Checking the PWB performance Video input in trouble RGB input in trouble Go to "Checking the video unit circuit". Feed test pattern signal from PC. Through-output in trouble Through-output circuit in trouble. No Is specified cable connected between PC and projector? Yes Use specified cable. Is supply voltage as specified? No Yes Power circuit in trouble. No Does image appear? Yes Check the connectors, starting from the PC input circuit.
PG-C30XU TROUBLE SHOOTING TABLE (Continued) Checking the video system No Is the lamp on? Yes Go to "Lamp fails to light-up". No Is specified voltage fed to EA connectors? Yes Check the power circuit and its parts. Are there signal inputs at pins (3) and (29) of P402? No Yes Are there signals at pin (4) of IC401 and pin (4) of IC402? Are there signal outputs at pins (3) and (6) of IC816? Yes Yes No Go to "Checking IC801 (RGB signal output circuit)".
PG-C30XU TROUBLE SHOOTING TABLE (Continued) Checking IC801 (RGB signal output circuit) No Are there RGB output waveforms at pins (31), (32) and (33) of IC801? No Yes Go to "No color or unusual tone", "No Y signal" or "Out of sync". Are there output waveforms at the emitters of Q1501, Q1502 and Q1503? Check the data transfer and other performance at pins (17) and (18) of video IC801.
PG-C30XU TROUBLE SHOOTING TABLE (Continued) Checking IC806 (3-D noise reduction circuit) and its peripheral circuits Are there signal inputs at pins (40) (Y signal) and (45)(chroma signal) of IC806? No Yes Are there signal outputs at pins (55) (Y signal) and (51)(chroma signal) of IC806? Check the buffer circuit of Q814 thru Q816 as well as Q903 thru Q906.
PG-C30XU TROUBLE SHOOTING TABLE (Continued) No or unusual Y signal Is there Y signal input at pin (21) of IC801? No Yes Is there Y signal output at pin (40) of IC801? Go back to the signal processing block. No Yes Is there Y signal output at pin (17) of IC803? Check IC801 and its peripheral circuits. No Yes Check IC803 and its peripheral circuits as well as IC805 (AGC). Check IC803 and its peripheral circuits.
PG-C30XU TROUBLE SHOOTING TABLE (Continued) Checking the output PWB unit No If there is no signal at SC1501 and SC1502, go to the video system block. If there is no signal at SC1404 and SC1405, go to "Trouble shooting table for PC I/F unit". Are there signal inputs at No SC1404, SC1405, SC1501 and SC1502? Are voltages applied to EA connectors and SC5502? If there is no signal at EA connector or SC5502, go to Yes Checking the power unitblock.
PG-C30XU TROUBLE SHOOTING TABLE (Continued) No audio output Are there audio signal inputs at pin (2) of IC1411? No Yes Check the input, the switching circuit of IC3303 and IC3304, and their peripheral circuit,SC3001,SC1502,etc. Are there audio signal outputs at pin (2) of P5508? No Yes Check the IC1411 control voltage,and its peripheral circuits. Are there audio signal outputs at pin (6) of IC7301? No Yes Check IC7301 and its peripheral circuits.
PG-C30XU TROUBLE SHOOTING TABLE (Continued) Power on Is the right input selected? No Yes Select the right input with remote control. Are the PC, video and LCP cables as No specified and properly connected? Yes Use the right cables or reconnect the cables. With the contrast control at maximum, Yes does the image appear? No Readjust the video system. Is the voltage at CON3 (P8502) connector as specified? No Yes Power circuit faulty. Hook up a personal computer.
PG-C30XU TROUBLE SHOOTING TABLE (Continued) Lamp fails to light-up Yes Turn on the power switch. Is discharging sound heard from the lamp? No Is the lamp out of socket? Yes No Is the ballast cooling fan running? Reconnect the lamp into socket. Replace the lamp. No Yes Check the power circuit. Is DC 360V voltage applied between PL connector pins? No Yes Yes Is 2V or higher voltage applied between pins (1) and (2) of ballast’s D connector? No Replace the ballast.
PG-C30XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-1 Checking the clock circuit and its peripheral circuits Is X8001 (6MHz) oscillating? No X8001 or its peripheral part faulty. Yes Is X8003 (1.84MHz) oscillating? No X8003 or its peripheral part faulty. Yes Is X8004 (22.165MHz) oscillating? No X8004 or its peripheral part faulty. Yes Is X8005 (16.25MHz) oscillating? No X8005 or its peripheral part faulty. Yes Does pin (162) of IC8001 function? No IC8001 or its peripheral circuit faulty.
PG-C30XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-2 Checking the PLL circuit and its peripheral circuits Are there signals at pin(111) of IC8606 and TL8606? No Yes IC8025 or its peripheral circuit faulty. Are there signals at pins (100) and (101) of IC8606? No Yes IC8606 or its peripheral circuit faulty. Check the video circuit and its peripheral circuits.
PG-C30XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-3 Checking the SXGA's red video circuit and its peripheral circuits Is there signal at pin (139) of IC8606? Checking the VGA's red video circuit and its peripheral circuits No No Is there signal at pin (139) of IC8606? Yes Yes output PWB faulty.
PG-C30XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-4 Checking the SXGA's green video circuit and its peripheral circuits Is there signal at pin (124) of IC8606? Checking the VGA's green video circuit and its peripheral circuits No No Is there signal at pin (124) of IC8606? Yes Yes output PWB faulty.
PG-C30XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-5 Checking the SXGA's blue video circuit and its peripheral circuits Is there signal at pin (133) of IC8606? Checking the VGA's blue video circuit and its peripheral circuits No No Is there signal at pin (133) of IC8606? Yes Yes outpur PWB faulty. Are there signals at pins (45) thru (49), (51), thru (53), (56) thru (58), (60) thru (64) of IC8606? No Yes Are there signals at TL8048 and TL8049? No Yes IC8606 or its peripheral circuit faulty.
PG-C30XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-6 Checking the OSD circuit and its peripheral circuits Display OSD on the screen. Yes Are there signals at pins (56), (58), (71) and (72) of IC8048? No Yes IC8029 or its peripheral circuit faulty. Are there signals at pins (12), (14) thru (17) and (20) of IC8048? No Yes IC8048 or its peripheral circuit faulty. Are there signals at pins (23) thru (42) of IC8048? No Yes IC8046, IC8047 or their peripheral circuit faulty.
PG-C30XU CHASSIS LAYOUT OUTPUT UNIT DUNTKA215FE01 H PC I/F UNIT CPCI-0047CE01 INLET UNIT RUNTK0677CEZZ G F SIGNAL UNIT DUNTKA211DE01 E S-OUT/REG UNIT DUNTKA214DE01 VIDEO UNIT DUNTK9769DE20 D C POWER UNIT RDENC0311CEZZ BALLAST UNIT RDENC0313CEZZ PC TERMINAL UNIT DUNTKA212DE01 B A 1 2 3 48 4 5 6 7 8 9 10 11 49 12
PG-C30XU BLOCK DIAGRAM H G F E D C B A 1 2 3 50 4 5 6 7 8 9 10 11 51 12
PG-C30XU OVERALL WIRING DIAGRAM H G F E D C B A 1 2 3 52 4 5 6 7 8 9 10 11 53 12
PG-C30XU DESCRIPTION OF SCHEMATIC DIAGRAM H VOLTAGE MEASUREMENT CONDITION: 1. Voltages at test points are measured at the supply voltage of AC 120V. Signals are fed by a color bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/ V tester. G WAVEFORM MEASUREMENT CONDITION: 1. Waveforms at test points are observed at the supply voltage of AC 120V. Signals are fed by a color bar signal generator for servicing purpose.
PG-C30XU WAVEFORMS 1 SC1101 7-pin 2 SC1101 8-pin (RP SIG5) H : 10µsec/div V : 2V/div (RP SIG6) H : 10µsec/div V : 2V/div 5 SC1301 7-pin 6 SC1301 8-pin (BP SIG5) H : 10µsec/div V : 2V/div (BP SIG6) H : 10µsec/div V : 2V/div 9 P801 4-pin 4 SC1201 8-pin (GP SIG5) H : 10µsec/div V : 2V/div (GP SIG6) H : 10µsec/div V : 2V/div 7 P801 1-pin 8 P801 2-pin (R) H : 10µsec/div V : 0.5V/div 0 IC604 6-pin (B-Y) H : 20µsec/div V : 1V/div 3 SC1201 7-pin (G) H : 20µsec/div V : 0.
PG-C30XU Ë SIGNAL UNIT-1/2 H G F E D C B A 1 2 3 56 4 5 6 7 8 9 10 11 57 12
PG-C30XU Ë SIGNAL UNIT-2/2 H G F E D C B A 1 2 3 58 4 5 6 7 8 9 10 11 59 12
PG-C30XU Ë PC TERMINAL UNIT H G F E D C B A 1 2 3 60 4 5 6 7 8 9 10 11 61 12
PG-C30XU Ë SOUND OUT/REGULATOR UNIT H G F E D C B A 1 2 3 62 4 5 6 7 8 9 10 11 63 12
PG-C30XU Ë OUTPUT UNIT-1/6 H G F E D C B A 1 2 3 64 4 5 6 7 8 9 10 11 65 12
PG-C30XU Ë OUTPUT UNIT-2/6 H G F E D C B A 1 2 3 66 4 5 6 7 8 9 10 11 67 12
PG-C30XU Ë OUTPUT UNIT-3/6 H G F E D C B A 1 2 3 68 4 5 6 7 8 9 10 11 69 12
PG-C30XU Ë OUTPUT UNIT-4/6 H G F E D C B A 1 2 3 70 4 5 6 7 8 9 10 11 71 12
PG-C30XU Ë OUTPUT UNIT-5/6 H G F E D C B A 1 2 3 72 4 5 6 7 8 9 10 11 73 12
PG-C30XU Ë OUTPUT UNIT-6/6 H G F E D C B A 1 2 3 74 4 5 6 7 8 9 10 11 75 12
PG-C30XU Ë VIDEO UNIT H G F E D C B A 1 2 3 76 4 5 6 7 8 9 10 11 77 12
PG-C30XU Ë POWER and INLET UNIT (POWER) H G F E D C (INLET) B A 1 2 3 78 4 5 6 7 8 9 10 11 79 12
PG-C30XU Ë PC I/F UNIT-1/9 H G F E D C B A 1 2 3 80 4 5 6 7 8 9 10 11 81 12
PG-C30XU Ë PC I/F UNIT-2/9 H G F E D C B A 1 2 3 82 4 5 6 7 8 9 10 11 83 12
PG-C30XU Ë PC I/F UNIT-3/9 H G F E D C B A 1 2 3 84 4 5 6 7 8 9 10 11 85 12
PG-C30XU Ë PC I/F UNIT-4/9 H G F E D C B A 1 2 3 86 4 5 6 7 8 9 10 11 87 12
PG-C30XU Ë PC I/F UNIT-5/9 H G F E D C B A 1 2 3 88 4 5 6 7 8 9 10 11 89 12
PG-C30XU Ë PC I/F UNIT-6/9 H G F E D C B A 1 2 3 90 4 5 6 7 8 9 10 11 91 12
PG-C30XU Ë PC I/F UNIT-7/9 H G F E D C B A 1 2 3 92 4 5 6 7 8 9 10 11 93 12
PG-C30XU Ë PC I/F UNIT-8/9 H G F E D C B A 1 2 3 94 4 5 6 7 8 9 10 11 95 12
PG-C30XU Ë PC I/F UNIT-9/9 H G F E D C B A 1 2 3 96 4 5 6 7 8 9 10 11 97 12
PG-C30XU PRINTED WIRING BOARD ASSEMBLIES H G F E Signal Unit (Wiring Side) D C PC Terminal Unit (Wiring Side) B A Video Unit (Wiring Side) 1 2 3 4 98 5 6
PG-C30XU H G F E Signal Unit (Component Side) D C PC Terminal Unit (Component Side) B A Video Unit (Component Side) 1 2 3 4 99 5 6
PG-C30XU H G F E D C B A Output Unit (Wiring Side) 1 2 3 4 100 5 6
PG-C30XU H G F E D C B A Output Unit (Component Side) 1 2 3 4 101 5 6
PG-C30XU H G F E PC I/F Unit (Wiring Side) D C B A PC I/F Unit (Component Side) 1 2 3 4 102 5 6
PG-C30XU H G F E Sound Out/Regulator Unit (Wiring Side) D C B A Sound Out/Regulator Unit (Component Side) 1 2 3 4 103 5 6
PG-C30XU H G F Power Unit (Wiring Side) E D C B Power Unit (Component Side) A 1 2 3 4 104 5 6
PG-C30XU H G F Inlet Unit (Wiring Side) E D C B Inlet Unit (Component Side) A 1 2 3 4 105 5 6
PG-C30XU Ref. No. Part No. ★ Description Code Ref. No. ★ Part No. Description PARTS LIST DUNTKA211DE01 PARTS REPLACEMENT SIGNAL UNIT INTEGRATED CIRCUITS Parts marked with "å" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. Les pieces marquées "å" sont importantes pour maintenir la sécurité de l'appareil.
PG-C30XU Ref. No. Part No. ★ Description Code Ref. No.
PG-C30XU Ref. No. ★ Part No.
PG-C30XU Ref. No. Part No. ★ Description Code Ref. No. ★ Part No.
PG-C30XU Ref. No. ★ Part No.
PG-C30XU Ref. No. Part No. ★ Description Code Ref. No. ★ Part No.
PG-C30XU Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description DUNTKA214DE01 DUNTKA215FE01 SOUND OUT/REGULATOR UNIT (Continued) OUTPUT UNIT R7311 R7312 R7313 R7315 R7316 R7317 VRS-CY1JF103J VRS-TX2HF8R2J VRS-CY1JF223J VRS-TX2HF2R2J VRS-TX2HF2R2J VRS-CY1JF102J UNT1001 FB1001 FB1002 FB1005 P1010 P1011 P7302 P7303 RCNVD0014CEZZ RBLN-0062CEZZ RBLN-0062CEZZ RBLN-0060CEZZ QPLGN0428FJZZ QPLGN0430FJZZ QPLGN0464TAZZ QPLGN0174FJZZ PRDAR1551CEFW LX-BZ3266CEFD J J J J J J 10k 8.2 22k 2.
PG-C30XU Ref. No. ★ Part No.
PG-C30XU Ref. No. Part No. ★ Description Code Ref. No.
PG-C30XU Ref. No. ★ Part No.
PG-C30XU Ref. No. Part No. ★ Description Code Ref. No. Part No.
PG-C30XU Ref. No. Part No. ★ Description Code Ref. No. Part No.
PG-C30XU Ref. No. Part No. ★ Description Code Ref. No. Part No.
PG-C30XU Ref. No. ★ Part No.
PG-C30XU Ref. No. ★ Part No.
PG-C30XU Ref. No. ★ Part No. Description Code INLET UNIT PACKAGED CIRCUIT TNR761 9FJ0F20001280 å å L761 L762 L763 J ENE471D10A AD L701 L702 L703 L704 å T701 COILS 9FJ0L05001460 9FJ0L05001460 9FJ0L08001660 C761 C762 C763 C764 C765 C766 C767 9FJ0C34001763 9FJ0C51001223 9FJ0C51001223 9FJ0C34001753 9FJ0C34001763 9FJ0C34001763 9FJ0C34001763 R761 9FJ0R11002110 J J J J J J J 0.22 1000p 1000p 0.1 0.22 0.22 0.22 250V 250V 250V 250V 250V 250V 250V M.Polyester Ceramic Ceramic M.Polyester M.
PG-C30XU Ref. No. R731 R732 R733 R734 R735 R736 R737 R738 R739 R740 R741 R742 R743 R744 R745 R746 R747 R748 R749 R750 R753 R754 R755 R756 R757 R758 R759 R770 R771 Part No. ★ Description Code Ref. No. ★ Part No.
PG-C30XU Ref. No. ★ Part No.
PG-C30XU Ref. No. ★ Part No.
PG-C30XU Ref. No. Part No.
PG-C30XU Ref. No. Part No.
1 A 2 13 58 20 3 127 G 20 36 EA D 14 9 4 41 7 F SP 8 H 43 33 5 25 3-6 3-19 3-2-14 3-7 3-23 3-8 1-5 3-9 1-3 F 3-10 3-2-5 3-17 3-5 3-16 1-6 L 3-2-2 3-2-1 3-2-9 3-2-9 3-2-13 3-2-12 1-1-6 1-1-1 6 3-2 3-2-4 3-2-7 1-1 1-1-5 3-11-2 3-11 3-20 C 3-2-10 59 2-2 3-12 3-2-8 3-22 3-2-11 A 3-21 3-2-6 1-1-3 2-1 3-11-1 3-3 3-1 3-1-2 3-1-4 3-1-3 43 3 E 3-1-1 3-1-1-1 3-1-1-3 3-1-1-4 3-1-1-2 29 57 2-1-1 2-1-2 35 H SO C B 1-6 1-4 1-1-
PG-C30XU Ref. No. Part No.
1 2 A 3 129 6-86 4 6-57 6-12 6-75 6-83 6-85 6-78 6-79 6-79 6-47 6-54 6-19 6-18 6-17 6-26 6-1 6-24 6-29 6-30 6-2 6-16 6-14 6-49 6-32 6-35 6-23 6-20 6-22 6-25 6-32 6-51 6-66 6-51 6-14 6-51 6-54 6-54 6-25 6-27 6-31 6-21 6-73 6-80 6-10 5 6-8 81 6-15-2-1 6-15-4 6-15-5 6-15-7 6-15-2-3 6-15-2 6-77 6-52 6-15-9 6-15-12 6-15-2-2 6-15-10 6-72 6-15-3 6-15-6 6-15-8 6-88 6-79 6-79 6-87 6-15-11 6-15-1 6-15 6-84 6-71 6-9 6-87 6 Part No.
PG-C30XU Ref. No. Part No.
PG-C30XU Part No. ★ Description Code POWER/BALLAST PARTS Ref. No. Ref. No. ★ Part No.
PG-C30XU Ref. No. Part No.
