User Manual

ManualsBrandsSharp ManualsMonitorsPN-70TA3

３.

Turn on the power

Power button/Power LED

(1) Turn on the main power

switch.

Set a AAA battery in the touch pen and the AA

battery in the Remote Control Unit.

Connect the touch pen adapter

２.

Prepare the touch pen and the Remote

control Unit

Insert the touch pen adapter into the touch

pen adapter port on the backside of the

monitor.

(２) Push the power button.

４.

Set the operation mode

Easy Setup Guide for PN-70TA3/PN-60TA3

LED Status

Status of the monitor

Green

Power on

Orange

Power off(Standby mode)

Orange flashing

Power off

(Whiteboard standby mode)

Green flashing

Input signal waiting mode

Set the date/time of the monitor

Set the date and time by the remote control

unit.

Set the operation mode by the remote control

unit.

Enable the system mode

(1) Touch a toolbar

in the launcher.

(３) Enter password.

(２) Touch “Settings”

in the launcher menu.

Enter the password set in admin password.

If a password is not set , enter “00000”

Summary of content (7 pages)

PAGE 1
Easy Setup Guide for PN-70TA3/PN-60TA3 1. Connect the touch pen adapter Insert the touch pen adapter into the touch pen adapter port on the backside of the monitor. ４. Set the operation mode by the remote control unit. 5. ２. Prepare the touch pen and the Remote control Unit Set the operation mode Set the date/time of the monitor Set the date and time by the remote control unit. Set a AAA battery in the touch pen and the AA battery in the Remote Control Unit. ３.
PAGE 2
(4) Touch “System mode” on “System Settings” tab. (2) Touch “Change time zone...” on “Date and Time” tab. (5) Enter system password. Enter the password set in system password. If a password is not set , enter “00000” Enter system password The monitor is automatically restarted in System mode. 7. (3) Touch “Change date and time...” on “Date and Time” tab. Date and Time setting (1) Touch “Date and Time” on “System Settings” tab. Set date, time, and time zone. Set the date and time.
PAGE 3
and Language” settings 8. “Region for the Operation System (1) Touch “Region and Language Settings” on “System Settings” tab. (5) Select the system locale according to your language. (2) Select the format. When the following message is displayed, click “Apply” button to continue. When the following dialog is displayed, select your own language. (3) Select the location. After touching “OK” button, the following message is displayed and touch “Cancel” button. (4) Select the keyboards and languages.
PAGE 4
9. “Language” settings of SHARP Software (1) Touch “Language” button. (2) Select your language. 10. Return to “Normal mode” (1) Touch “Normal mode” button. (2) Enter system password. Enter the password set in system password. If a password is not set , enter “00000” Enter system password If you select “English”, please select “SHARP Cloud Portal Office” location settings. Whiteboard will be started. (3)Touch “Apply” button.
PAGE 5
11. Printer settings (by using discovery function) (5) When selecting Printer by using discovery function, touch “Search” button. (1) Touch “Printer Settings” button. A search dialog is displayed. (2) Select a Universal Printer “SHARP UD2_PCL6_FS2”, and show Printer properties by opening the right-click menu. (3)Touch “Settings” tab. (4) Touch “Printer Selection” button. Available printers are shown on the search result list. (6) Select one from the result list. (ex.) [SHARP MX-4100F….
PAGE 6
12. Printer settings (Select printer manually) Before the installation of the printer, please confirm that the white board connected to the same network. (1) Touch “Manually Add >” button. (6) Select necessary item on check box, and touch “OK” button. (*)The initial values are all check OFF. Please tap “Defaults” button to reset to their initial values. (2) Input printer settings properly and touch “OK” Button. (7) Regarding Punch Module, touch “Punch Module” list box.
PAGE 7
13. Scanner settings (Network Scanner Tool Lite) (4) Check scanners from which you want to scan. Before the installation of the scanner, please confirm that the white board connected to the same network. (1) Touch “NST-Lite Setup” on “BASIC Setting” tab. You can confirm scanners’ IP address from “Properties” to identify them. (2) Touch “Scanners” tab. (5) Touch “Apply” to save profile to the scanner. Then touch “OK” to close. (3) Touch “Auto Detect” to automatically find scanners.