Instruction manual

22
E
n
AUDIO
TREBLE
Adjuststhevolumeoftreble-levelsound.
BASS
Adjuststhevolumeofbass-levelsound.
BALANCE
Adjuststhebalanceoftheaudiosoundbetweenrightandleft.
RESET
ResetsthevaluesoftheAUDIOmenuitemstothefactorypresetvalues.
Select “ON” and then press
MENU
.
n
SETUP
OSD H-POSITION
Adjuststhehorizontaldisplaypositionofmenuscreen.
OSD V-POSITION
Adjuststheverticaldisplaypositionofmenuscreen.
SCREEN MOTION
Residual images are reduced by moving the screen.
PATTERN1 ......... The whole screen moves vertically and
horizontally.
PATTERN2 ......... A black screen spreads from the bottom of
the screen and then shrinks to the bottom
of the screen. If the monitor is installed
in the vertical orientation, a black screen
spreads from the left end of the screen and
then shrinks to the left end of the screen.
PATTERN3 ......... A black bar moves from the left end to the
right end of the screen. If the monitor is
installed in the vertical orientation, a black
bar moves from the top to the bottom of
the screen.
PATTERN4 .........Blackscreensappearfromboththe
top and bottom of the screen, and the
displayed image is compressed into the
centraleld.Ifthemonitorisinstalled
in the vertical orientation, the screen is
compressed from the left and right ends.
PATTERN1 PATTERN2
PATTERN4PATTERN3
MOTION TIME 1
Specifyatimeperiod(operatinginterval)untilSCREEN
MOTION starts.
MOTION TIME 2
SpecifyatimeperiodduringwhichSCREENMOTION
operates (time period during which the screen will move).
MONITOR
Select the installation direction of the monitor.
LANDSCAPE ............Horizontalorientation
PORTRAIT ...............Verticalorientation
MONAURAL AUDIO
Outputs audio signals as monaural.
LANGUAGE
Sets the display language for the menu screen.
POWER ON DELAY
You can delay the screen display after the monitor is turned
on. The period can be set up to 60 seconds in units of one
second.Whenthisfunctionisactivated,thepowerLED
ashes(atapprox.1secondinterval)inorange.Thisfunction
isdisabledwhen0isspecied.
STANDBY MODE
WhenSTANDARDisselected,startuptimefromstandby
mode is reduced. Note, however that, more power will be
consumed in standby mode.
WhenLOWPOWERisselected,currentconsumption
is reduced while the monitor is in standby mode. Note,
however, that the startup time from standby mode becomes
longer.Also,certainRS-232Ccommandscannotbeused
in standby mode, and control via LAN will be disabled. (See
pages 32 and 38.)
OFF IF NO OPERATION
Determineswhetherornottosetthemonitortogointo
standby mode when there is no operation from the remote
controlunit,RS-232Ccommands,orLANforover4hours.
HDMI SETTING
HDMIAUTOVIEW
.........................WhenONisselected,thescreensizeis
adjustedautomaticallyaccordingtothe
screensizecontrolsignalincludedinthe
videosignalinputfromtheAVHDMIinput
terminal.
HDMIRGBINPUTRANGE
.........................SetsthetypeofHDMIsignalswhenusing
theAVHDMIinputmode.
WhenAUTOisselected,thetypeisset
automatically.
HOT PLUG CONTROL
SetswhethertousehotplugcontrolforthePC/AVHDMI
andPC/AVDVI-Dinputterminals.
RS-232C/LAN SELECT
Selects the method with which to control the monitor from
the computer.
ID No. SET
AssignsIDnumberstomonitorsconnectedinadaisychain
(seepage29),usingRS-232cables.
Thenumbers1to255areavailableforIDnumbers.
If“0”isset,thesystemregardsthisasthestatewherenoID
number is set.
BAUD RATE
SelectsthecommunicationspeedusedforRS-232C
communication.
Menu Items