LCD MONITOR TOUCH PEN UTILITY OPERATION MANUAL Version 2.0 Applicable models (as of December 2015) PN-60TA3*/PN-60TB3/PN-60TW3/PN-70TA3*/PN-70TB3/PN-70TW3/PN-80TC3/ PN-L603A*/PN-L603B/PN-L603W/PN-L703A*/PN-L703B/PN-L703W/PN-L803C/ PN-ZL01/PN-ZL02/PN-ZL03 * Excluding WHITEBOARD mode (Available models differ according to region.
Contents Introduction.......................................................................3 System Requirements...................................................3 Setting up the PC..............................................................4 Install.............................................................................4 Showing active pen information.....................................5 Active pen settings...........................................................6 How to configure settings.....
Introduction This software enables a touch pen to be used on a computer connected to the video input terminal of an applicable model. To use a touch pen with a computer, this software must be installed on the computer. The touch pen (3 button pen) that is included with an applicable model is referred to as “active pen” in this manual. System Requirements OS Windows 7 (32-bit or 64-bit version), Windows 8 (32-bit or 64-bit version), Windows 8.
Setting up the PC Install Caution • Connect the touch panel, and then install the Touch Panel Settings Tool. • Insert the touch pen adapter into the LCD monitor before installing the Touch Pen Utility. • If an older version of the Touch Pen Utility is installed, remove (uninstall) the old version before installing the Touch Pen Utility. (See page 10.) • This can only be done by a user with administrator authority. 1. 2. 3. 4. 5. 6. Start your PC. Exit all applications that are running.
Showing active pen information The Touch Pen Utility starts automatically. You can view information on the active pen that is being used. 1. Click the Touch Pen Utility icon ( ) on the taskbar. • Touch pen information : Shows the registration number, the battery level and the signal strength of the active pen being used. • Touch pen settings : See page 6. • Operation settings : See page 9. • Version Information : Shows the version of this software. • Exit : Exit this software.
Active pen settings How to configure settings Settings that can be changed are as follows. • Registering/canceling an active pen: See page 7. • Advanced: See page 7. - Touch pen setting: See page 7. -F unction buttons: See page 8. - Test Information: Shows the active pen function buttons, pen pressure levels, and other information. (For service technicians.) 1. Click the Touch Pen Utility icon ( ) on the taskbar. 2. Click [Touch pen settings]. 3. Change the settings. (See page 7.
Active pen settings Registering/canceling an active pen To use the optional active pen, you must register the active pen (pairing). You can also cancel the registration of an active pen. nRegistering an active pen See the operation manual for the LCD monitor. nCanceling the registration of an active pen 1. Click the active pen you want to cancel in the touch pen settings screen. 2. Click [Release]. Advanced 1. Click the active pen whose settings you want to change in the touch pen settings screen. 2.
Active pen settings nCustomize touch pen pressure You can adjust the pen pressure in the Pen Software. Touch pen pressure table setting You can manually adjust the touch pen pressure and stroke thickness. Preset The touch pen pressure table can be selected and set from the presets. Preset settings The set touch pen pressure table can be assigned a name and saved. (Up to 10.) In addition, saved presets can be deleted.
Operation settings Input mode Set the action for touch by finger or active pen. It is normally recommended that you use “Standard”. • Standard : The touch action takes place when the screen is touched by active pen or finger. : The touch action takes place only when the screen is touched by active pen. The touch action does not takes • Pen place when the screen is touched by finger. • Pen Digitizer : You can use an active pen as a digitizer pen in Windows.
Uninstall Caution • This can only be done by a user with administrator authority. 1. Click the Touch Pen Utility icon ( ) on the taskbar and click “Exit”. • If a confirmation window appears, click “Yes”. 2. Remove the touch pen adapter. 3. Select “Control Panel” from the “Start” menu. 4. Click “Uninstall a program”. • If you are using icon view, click “Programs and Features”. 5. Select “SHARP Touch pen utility” and click “Uninstall”. • Follow the on-screen instructions.
PU V2.
