LCD MONITOR Touch pen Management Tool OPERATION MANUAL Applicable models (as of August 2017) PN-60TB3/PN-60TW3A/PN-70TB3/PN-70TW3A/PN-80TC3A/PN-L603B/PN-L603WA/PN-L703B/ PN‑L703WA/PN-L803CA PN-ZL01A/PN-ZL02A/PN-ZL03A (Available models differ according to region.) Version 3.
Contents Introduction.......................................................................3 System Requirements...................................................3 Setting up the computer..................................................4 Install.............................................................................4 Showing touch panel / touch pen information...............5 Touch panel settings........................................................6 Touch pen settings.............................
Introduction This software can be used to configure settings for touch action when using a touch pen or touch action on a computer connected to the video input terminal of an applicable model. To use a touch pen or touch action with a computer connected to applicable model, this software must be installed on the computer. The touch pen (3 button pen) that is included with an applicable model is referred to as “active pen” in this manual.
Setting up the computer Install Caution • Insert the touch pen adapter into the LCD monitor before installing this software. • If an older version of this software is installed, remove (uninstall) the old version before installing this software. (See page 11.) • This can only be done by a user with administrator authority. 1. Start your computer. 2. Exit all applications that are running. 3. Connect the USB cable. After it has been connected, the touch panel will be automatically recognized.
Showing touch panel / touch pen information This software starts automatically. You can view information on the operation mode being set and active pen being used. 1. Click the Touch pen Management Tool icon ( ) on the taskbar. Touch Panel Device: Shows the connected monitor. Touch Panel Settings: Shows the current touch operation mode. To change the touch operation mode, click this part. (See page 6.
Touch panel settings 1. Click the Touch pen Management Tool icon ( ) on the taskbar. 2. Click the place on the “Touch Panel Settings” that shows the touch operation mode. 3. Change the settings. nTouch Operation Mode Setting Select operation mode of the touch panel. Standard Touch Mode: The touch action takes place when the screen is touched by active pen or finger. Pen dedicated Mode: The touch action takes place only when the screen is touched by active pen.
Touch pen settings Change the active pen settings 1. Click the Touch pen Management Tool icon ( ) on the taskbar. 2. Click the active pen that you want to set in the touch pen list of the “Touch Pen Settings”. 3. Click the tab of the item you want to set and change the settings. nBasic Showing information Shows the firmware version and ID of the selected active pen. Unregister Release the registration (pairing) of the selected active pen.
nPen Input pen pressure Shows the current amount of pen pressure. Start value of pen pressure detection Set how hard the active pen must be pressed to be recognized. Saturation value (100%) of pen pressure Set the amount of active pen pressure that is treated as the maximum pressure. Automatic setting Normally not used. If pen pressure is detected when the pen tip is not being pressed, the pen pressure will be automatically adjusted. Do not press the pen tip during automatic setting.
nFunction buttons Functions can be assigned to the function buttons 1 to 3 of an active pen. After selecting a function button, select the function to be assigned to the button. Function button 3 Function button 2 Function button 1 Functions that can be assigned to function buttons 1 to 3 are as follows.
Registering(pairing)/unregistering an active pen Up to 4 active pens can be used simultaneously. To use the optional active pen, you must register the active pen (pairing). Up to 8 active pens can be registered. You can also cancel the registration of an active pen. nRegistering an active pen Perform active pen pairing for one pen at a time. 1. Click the Touch pen Management Tool icon ( ) on the taskbar. 2. Click “Touch pen registration” in the “Touch pen settings”. 3. Click “Registration”. 4.
Uninstall Caution • This can only be done by a user with administrator authority. 1. Click the Touch pen Management Tool icon ( ) on the taskbar and click “Exit tool”. • If a confirmation window appears, click “Yes”. 2. Select “Control Panel” from the “Start” menu. 3. Click “Uninstall a program”. • If you are using icon view, click “Programs and Features”. 4. Select “SHARP Touch pen Management Tool” and click “Uninstall”. • Follow the on-screen instructions.
PM V3.
