PN-80TC3A LCD MONITOR OPERATION MANUAL
Information on the Disposal of this Equipment and its Batteries IF YOU WISH TO DISPOSE OF THIS EQUIPMENT OR ITS BATTERIES, DO NOT USE THE ORDINARY WASTE BIN, AND DO NOT PUT THEM INTO A FIREPLACE! Used electrical and electronic equipment and batteries should always be collected and treated SEPARATELY in accordance with local law. Separate collection promotes an environment-friendly treatment, recycling of materials, and minimizing final disposal of waste.
IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DEAR SHARP CUSTOMER Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product. SAFETY PRECAUTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety.
SAFETY PRECAUTIONS (Continued) 19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment, dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below: • Use the specified batteries only. • Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the compartment. • Do not mix old and new batteries.
TIPS AND SAFETY INSTRUCTIONS - The TFT color LCD panel used in this monitor is made with the application of high precision technology. However, there may be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from an acute angle there may be uneven colors or brightness. Please note that these are not malfunctions but common phenomena of LCDs and will not affect the performance of the monitor.
MOUNTING PRECAUTIONS • This product is for use indoors. • A mounting bracket compliant with VESA specifications is required. • Since the monitor is heavy, consult your dealer before installing, removing or moving the monitor. • Mounting the monitor on the wall requires special expertise and the work must be performed by an authorized SHARP dealer. You should never attempt to perform any of this work yourself.
Contents IMPORTANT INFORMATION.............................................3 DEAR SHARP CUSTOMER...............................................4 SAFETY PRECAUTIONS...................................................4 TIPS AND SAFETY INSTRUCTIONS................................6 MOUNTING PRECAUTIONS.............................................7 Supplied Components......................................................9 System Requirements......................................................9 Part Names.......
Supplied Components If any components are missing, please contact your dealer.
Part Names nFront view 1 1. 2. 3. 4. 2 8 8 8 8 4 3 7 5 7 5. USB port (for USB device) (USB 2.0 compliant) To use, remove the seal and connect the USB cable on the back of the tray (“31”) to the computer. (See page 13.) 6. Tray 7. Speakers 8. Handles Remote control sensor (See page 15.) Power LED (See page 17.) POWER button (See page 17.) TOUCH MENU button (See page 24.
Part Names nRemote control unit 1 2 7 3 8 4 9 10 5 1. Signal transmitter 2. POWER button (See page 17.) 3. MUTE button (See page 25.) 4. VOL +/- buttons (See page 25.) BRIGHT +/- buttons (See page 25.) Cursor control ( / / / ) buttons 5. DISPLAY button (See page 25.) 6. MODE button (See page 25.) 7. INPUT button (See page 25.) 8. MENU button (See page 25.) 9. ENTER button (See page 25.) 10. RETURN button (See page 25.) 11. SIZE button (See page 25.
Connecting Peripheral Equipment 14 13 6 2 3 17 16 10 9 11 12 15 Caution • Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/ disconnecting cables. Also, read the manual of the equipment to be connected. • Be careful not to confuse the input terminal with the output terminal when connecting cables. Accidentally reversing cables connected to the input and output terminals may cause malfunctions and the other problems.
Connecting Peripheral Equipment 7. 8. • • Audio 1 input terminal Audio 2 input terminal Use an audio cable without resistance. Set the audio input terminal to be used in each input mode in AUDIO SELECT on the SETUP menu. 9. DisplayPort output terminal • The screen displayed on the monitor and the audio output from the monitor can be output to an external device. • Use a commercially available DisplayPort cable (conforming to the DisplayPort standard).
Connecting the Power Cord Caution Main power switch • Use only the power cord supplied with the monitor. 1 1. Turn off the main power switch. 2. Plug the power cord (supplied) into the AC input terminal. 3. Plug the power cord (supplied) into the power outlet.
Preparing the Remote Control Unit Installing the batteries Remote control operation range 1. Press the cover gently and slide it in the direction of the arrow. The operation range of the remote control unit is approx. 16.4 feet (5 m) at an angle of approx 10° from the center to the top/ bottom/right/left of the remote control sensor. 2. See the instructions in the compartment and put in the supplied batteries (R-6 (“AA” size) x 2) with their plus (+) and minus (-) sides oriented correctly. 3.
Removing the Handles The handles can be removed. Handle Handle screws Caution • The removable handles and handle screws are for use with this monitor. Do not use them for any other devices. • To attach handles, be sure to use the handles and handle screws which were removed from this monitor. • Be sure the handles are attached securely.
Turning Power On/Off Caution • Turn on the monitor first before turning on the computer or playback device. • When switching the main power switch or the POWER button off and back on, always wait for at least 5 seconds. A short interval may result in a malfunction. Turning power off Turning power off with monitor buttons Turning on the main power POWER button 1. Touch the POWER button. The recognition screen appears. 2. Touch [OK]. The power is turned off.
Turning Power On/Off nOperation mode When the monitor is turned on for the first time after being shipped from the factory, the operation mode setting screen will be displayed. Set it to MODE1 or MODE2. MODE1 ����OFF IF NO OPERATION is set to ON, and STANDBY MODE is set to LOW POWER. (These settings can not be changed.) Determines whether or not to set the monitor to go into standby mode when there is no operation from the remote control unit, or LAN for over 4 hours.
Touch Panel / Touch Pen Preparations Connecting the touch pen adapter Computer preparations To use the touch pen, insert the touch pen adapter into the touch pen adapter port on the monitor. To use the touch panel, the touch pen and the eraser, install the software below. • Touch pen Management Tool • Pen Software To install the software, see the manual for each.
Touch Panel / Touch Pen Preparations Touch pen actions nTouch pen settings Only use touch pens that are used with this monitor (supplied touch pens or optional PN-ZL03A). Function button 1 Function button 2 Touch pen settings are configured using the Touch pen Management Tool. For details on the settings and how to use the utility, see the Touch pen Management Tool Operation Manual.
Touch action Touch action Touch actions that can be used with this monitor differ according to operating system and application. The functions of touch actions are also different. For details, check Windows Help and the application’s support documentation. OS Windows 8.
Touch action Drag-and-drop Same action as drag-and-drop with a mouse. Touch the screen with your finger/touch pen and move without lifting. When you have finished the movement, lift your finger/ touch pen. nFinger actions Zoom Use in a screen that is capable of enlargement/reduction. Touch the screen with two fingers and move your fingers closer together to reduce the view, or apart to enlarge the view. Flicks Flick your finger/touch pen in the direction of the function you want to use.
Touch action Rotation Use this action in a screen that is capable of image rotation. Touch the center point of the rotation with one finger. While holding that finger still, move another finger in the desired direction of rotation. Move another finger in the desired direction of rotation Eraser With one finger touching • Hold the main body of the eraser with your bare fingers. The screen will not respond if you are wearing a glove. Only use an eraser that is supplied with this monitor.
Basic Operation Using the touch menu You can touch the monitor to change input mode, volume, and other settings. (2) V olume adjustment Changes the volume. 15 Increases the volume. 1. Touch the TOUCH MENU button. Decreases the volume. Mutes the sound. Touch again to return the sound to the original volume. TOUCH MENU button 2. Touch the screen to change settings. (3) T ouch action setting Touch to disable touch action. Touch again to enable touch action.
Basic Operation Using the remote control unit 1 2 5 6 9 3 4 5. BRIGHT +/- (Backlight adjustment) or displays the BRIGHT menu when the Pressing menu screen is not displayed. BRIGHT 15 Press or to adjust the brightness. * If you do not press any buttons for about 4 seconds, the BRIGHT menu automatically disappears. 6. ENTER Confirms the setting. 7 8 10 1. INPUT (Input mode selection) The menu is displayed. Press or to select the input ENTER to enter.
Basic Operation nSwitching the screen size Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE ZOOM 1 PC input Displays image so it fills the entire screen. AV input An image with a 4:3 aspect ratio is stretched to fill the entire screen. PC input An image with a 4:3 aspect ratio is enlarged to fill the entire screen without changing the aspect ratio. The edges of the image may be cut off.
Menu Items Displaying the menu screen TIPS Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 28 to 35 for details of each menu items. Caution • Do not turn the main power switch off while the menu items are being displayed. Doing so may initialize the settings. • The menu will differ depending on the input mode. • The menu screen will close automatically if no operation is performed for about 15 seconds.
Menu Items Menu item details The menu will differ depending on the input mode. nSCREEN You can move the menu screen display position each time DISPLAY is pressed. AUTO (D-SUB1[RGB]/D-SUB2) The CLOCK, PHASE, H-POS, and V-POS are automatically adjusted. ENTER Pressing performs adjustment. Use this automatic adjustment when you use the D-SUB1[RGB] or D-SUB2 to display a computer screen for the first time or when you change the setting of the computer. (See page 38.
Menu Items nPICTURE You can move the menu screen display position each time DISPLAY is pressed. BRIGHT Adjusts the backlight brightness. (In PIP mode, the main side setting is reflected in the image.) CONTRAST Adjusts the difference between the bright and dark portions of the image. BLACK LEVEL Adjusts the entire brightness of the video signals. TINT Adjusts the hue. Selecting + changes the color towards green, and selecting - changes it towards magenta. COLORS Adjusts the color intensity.
Menu Items ADVANCED AUTO (D-SUB1[RGB]/D-SUB2) The ANALOG GAIN and ANALOG OFFSET are automatically adjusted. ENTER Pressing performs adjustment. ANALOG GAIN (D-SUB1[RGB]/D-SUB2) Adjusts the bright portions of the video input signal. ANALOG OFFSET (D-SUB1[RGB]/D-SUB2) Adjusts the dark portions of the video input signal. 3D-NR (AV input) Reduce the noise of playback images on video. Setting a higher level reduces more noise. However, it may cause blurring on an image.
Menu Items nAUDIO TREBLE Adjusts the volume of treble-level sound. BASS Adjusts the volume of bass-level sound. BALANCE Adjusts the balance of the audio sound between right and left. RESET Resets the values of the AUDIO menu items to the factory preset values. ENTER . Select ON and then press nSETUP DATE/TIME SETTING to select the date and time, and press or or Set the date and time. Press Set the date in “Day/Month/Year” order. Set the time on a 24-hour basis.
Menu Items TOUCH INPUT SELECT These settings enable use of the touch panel according to input mode selection. BOTTOM USB Sets the input mode for use of the touch panel, which is connected to the USB port at the bottom of the monitor. In the landscape orientation, select the terminal into which the video signal of the computer connected to the USB 1 port will be input. When BOTTOM INPUT TERM.
Menu Items nMONITOR MONITOR Select the installation direction of the monitor. LANDSCAPE.............Landscape orientation PORTRAIT................Portrait orientation OSD H-POSITION Adjusts the horizontal display position of menu screen. OSD V-POSITION Adjusts the vertical display position of menu screen. OPERATION MODE MODE1 ������OFF IF NO OPERATION is set to ON, and STANDBY MODE is set to LOW POWER. (These settings can not be changed.) MODE2 ������Will perform standard operation.
Menu Items nPIP/PbyP PIP MODES Sets the display method. OFF �����������Displays one screen. PIP �������������Displays a sub screen inside a main screen. PbyP ����������Displays a main screen and a sub screen in a line. PbyP2 ��������Displays a main screen which measures 1280 pixels in the longest direction and a sub screen in a line. PIP SIZE Sets the size of the sub screen in PIP mode. PIP H-POS Adjusts the horizontal position of the sub screen in PIP mode.
Menu Items nOTHERS SCREEN MOTION PATTERN Residual images are reduced by moving the screen. OFF.................. SCREEN MOTION function is disabled. PATTERN1....... The whole screen moves vertically and horizontally. PATTERN2....... A black screen spreads from the bottom of the screen and then shrinks to the bottom of the screen. If the monitor is installed in the portrait orientation, a black screen spreads from the right end of the screen and then shrinks to the right end of the screen. PATTERN3.......
Menu Items nDual screen display You can display two screens simultaneously. Set this function with “PIP MODES” in the PIP/PbyP menu. PIP A sub screen is displayed inside a main screen. Main screen Sub screen PbyP Main screen Sub screen PbyP2 Main screen Sub screen A main screen and a sub screen are displayed in a line. Displays a main screen which measures 1280 pixels in the longest direction and a sub screen in a line. * The currently selected input signal is displayed on the main screen.
Menu Items nSCHEDULE Caution You can set the time to switch the monitor on and off. Set this function with “SCHEDULE” in the SETUP menu. (See page 31.) D-SUB1[RGB] SCHEDULE (2) No.
Menu Items Adjustments for PC screen display nAutomatic adjustment When you use D-SUB1 or D-SUB2 to display a computer screen for the first time, or when you change the setting of the computer, use the automatic screen adjustment. 1. Switch the input to D-SUB1 or to D-SUB2 and display the adjustment pattern. (See the description below.) MENU 2. Press and use or to display the SCREEN menu. 3. Press ENTER and select “AUTO”. ENTER . 4. Press The automatic adjustment is complete in several seconds. 5.
Initialization (Reset)/Functional Restriction Setting (FUNCTION) You can return the settings to their factory-preset values and restrict operations. SIZE down until “F” appears in the upper left 1. Hold corner of the screen. , , , in that 2. While “F” appears, press order.
Controlling the Monitor with a PC (RS-232C) You can control this monitor from a PC via RS-232C (COM port) on the PC. TIPS • To control the monitor via RS-232C, set RS-232C/LAN SELECT to RS-232C. • When STANDBY MODE is set to LOW POWER, control is not possible in standby mode. • You cannot use RS-232C and LAN control simultaneously. PC connection Connect the RS-232C conversion cable (supplied) to the RS232C input terminal on the monitor.
Controlling the Monitor with a PC (RS-232C) nResponse code format When a command has been executed correctly O K Return code (0DH, 0AH) A response is returned after a command is executed. When a command has not been executed E R R nCommunication interval • After OK or ERR is returned, you must send the following commands. To set a timeout for the command response, specify 10 seconds or longer.
Controlling the Monitor with a PC (RS-232C) Setting of the GAMMA user data nTo transfer the GAMMA user data Use the user data transfer commands (UGRW, UGGW and UGBW). For each of the R, G and B colors, divide the total 512 pieces of user data into 16 blocks, and transfer 32 pieces of data with each command.
Controlling the Monitor with a PC (RS-232C) RS-232C command table How to read the command table Command: Command field (See page 40.) Direction: W When the “Parameter” is set in the parameter field (see page 40), the command functions as described under “Control/Response Contents”. R The returned value indicated under “Reply” can be obtained by setting “????” or “ ?” in the parameter field (see page 40). Parameter: Parameter field (See page 40.
Controlling the Monitor with a PC (RS-232C) SCREEN menu Command Direction Auto Function ASNC W CLOCK CLCK WR PHASE positioning size RESOLUTION Parameter Reply Control/Response contents 1 When the input mode is D-SUB1[RGB], D-SUB2. 0-1200 0-1200 When the input mode is D-SUB1[RGB], D-SUB2. Varies depending on the signal. PHSE WR 0-63 Position of the longest direction HPOS WR 0-100 0-100 0-800 on D-SUB1[RGB], D-SUB2. Varies depending on the signal.
Controlling the Monitor with a PC (RS-232C) ADVANCED Function Command Direction AUTO AGIN W ANALOG GAIN ANGA Parameter Reply Control/Response contents 1 When the input mode is D-SUB1[RGB], D-SUB2. WR 0-127 0-127 When the input mode is D-SUB1[RGB], D-SUB2. 0-127 When the input mode is D-SUB1[RGB], D-SUB2.
Controlling the Monitor with a PC (RS-232C) SETUP menu Command Direction Date/time setting Function DATE WR DATE DISPLAY FORMAT DTFT WR TIME DISPLAY FORMAT TMFT WR 0-1 SCHEDULE SC01SC08 WR ABCDEFFGGH SCHEDULE BRIGHTNESS SB01SB08 WR 0-31 LANG WR LANGUAGE Parameter Reply AABBCCDDEE 0-2 INPUT MODE NAME AUDIO SELECT AUDIO OPTION E 0-2 0: YYYY/MM/DD, 1: MM/DD/YYYY, 2: DD/MM/YYYY YYYY: Year, MM: Month, DD: Day 0-1 0: 24-HOUR TIME, 1: 12-HOUR TIME ABCDEFFGGH Schedule of a specified
Controlling the Monitor with a PC (RS-232C) MONITOR menu Command Direction MONITOR Function STDR WR 0-1 0-1 OSD H-POSITION OSDH WR 0-100 0-100 OSD V-POSITION OSDV WR 0-100 0-100 OPERATION MODE FNCM WR 0-1 0-1 0: MODE1, 1: MODE2 STANDBY MODE STBM WR 0-1 0-1 0: STANDARD, 1: LOW POWER When ADJUSTMENT LOCK is set to ON2, LOW POWER cannot be selected (ERR). “ERR" when SCHEDULE is effective.
Controlling the Monitor with a PC (RS-232C) OTHERS menu Function Command Direction PATTERN SCSV WR MOTION TIME1 MTIM WR 0-20 MOTION TIME2 (PATTERN1) MINT WR 10-990 MOTION TIME2 (PATTERN2-4) MINT WR 5-20 POWER MANAGEMENT (PC) PMNG WR 0-1 0-1 0: OFF, 1: ON POWER MANAGEMENT (AV) PMAV WR 0-1 0-1 0: OFF, 1: ON CONNECT AUTO INPUT SELECT AICO WR 0-1 0-1 0: OFF, 1: ON NO SIGNAL AUTO INPUT SEL.
Controlling the Monitor with a PC (RS-232C) Initialization/Functional Restriction Setting (FUNCTION) menu Command Direction ALL RESET Function RSET W Parameter 0-1 Reply Control/Response contents ADJUSTMENT LOCK ALCK WR 0-2 0-2 0: OFF, 1:ON1, 2:ON2 When STANDBY MODE is set to LOW POWER, ON2 cannot be selected (ERR). ADJUSTMENT LOCK TARGET ALTG WR 0-2 0-2 0: REMOTE CONTROL, 1: MONITOR BUTTONS, 2: BOTH “ERR” when OFF is selected for ADJUSTMENT LOCK.
Controlling the Monitor with a PC (RS-232C) Commands for setting of the GAMMA user data Function E Command Direction RED GAMMA DATA TRANSFER UGRW W GREEN GAMMA DATA TRANSFER UGGW W BLUE GAMMA DATA TRANSFER UGBW W Parameter Reply aaxxxx ··· xxxxcc (xxxx: 32 pieces) aa: 01-16 xxxx: 0000-1023 cc: 00-FF RED GAMMA DATA READ UGRR W GREEN GAMMA DATA READ UGGR W BLUE GAMMA DATA READ UGBR W USER DATA INITIALIZE UGRS W 0 Initialize the user data.
Controlling the Monitor with a PC (LAN) Your monitor can be connected to a LAN allowing you to control it from a PC on the LAN. You can also configure the monitor to send e-mail notification when it has a problem. The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through). Network (LAN) Settings to connect to a LAN Set the monitor’s IP address and subnet mask to match the settings of your LAN.
Controlling the Monitor with a PC (LAN) nTo set from a PC When the monitor is connected to a PC, LAN settings can be configured via PC. Set up process (1) Connect your monitor to a PC (2) Specify the PC’s IP address (3) Configure the monitor’s LAN settings 7. Temporarily change the IP address and subnet mask. To access the monitor as it is shipped from the factory, set as follows. • IP Address: 192.168.150.1 • Subnet Mask: 255.255.255.
Controlling the Monitor with a PC (LAN) 5. Click on “LAN SETUP” under NETWORK. Controlling with a PC TIPS • For security, set a USER NAME and PASSWORD. (See page 55.) n Basic operation 6. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc. You use Internet Explorer on a PC on the LAN to control the monitor. 1. Launch Internet Explorer on the PC. 2. In the “Address” box, type “http://” followed by your monitor’s IP address followed by “/”, then press the Enter key.
Controlling the Monitor with a PC (LAN) nINFORMATION nADJUSTMENT Information about this monitor appears. You can adjust these settings which are also available on the monitor’s menu. • SCREEN (See page 28.) • PICTURE (See pages 29 to 30.) • AUDIO (See page 31.) • SETUP (See pages 31 to 32.) • MONITOR (See page 33.) • SCHEDULE (See page 37.) • PIP/PbyP (See page 34.) • OTHERS (See page 35.) • FUNCTION (See page 39.
Controlling the Monitor with a PC (LAN) nNETWORK (LAN SETUP) This screen allows you to set the settings necessary when the monitor is connected to a LAN. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ON. To set the address manually, set this to OFF. IP ADDRESS If the DHCP CLIENT is set to OFF, specify an IP address. SUBNET MASK If the DHCP CLIENT is set to OFF, specify the subnet mask.
Controlling the Monitor with a PC (LAN) nNETWORK (GENERAL) This screen allows you to specify the general LAN settings. MONITOR NAME Specify a name for this monitor as it should appear on the Internet Explorer screen. AUTO LOGOUT TIME Specify the time (in minutes) to elapse before automatically disconnecting this monitor from the network. Specify in minutes from 1 to 65535. A value of ‘0’ will disable this function. DATA PORT Specify the TCP port number to use for exchanging data with the monitor.
Controlling the Monitor with a PC (LAN) nMAIL (RECIPIENT) This screen allows you to specify the recipients of the e-mail sent periodically or when the monitor has an error. RECIPIENT E-MAIL ADDRESSES Specify the e-mail addresses to send error notification e-mail to. CONDITION Specify the conditions to send mails. When you check PERIODICAL, specify the date and time to send the mails in the PERIODICAL setting. CONFIRMATION Sends test e-mail.
Controlling the Monitor with a PC (LAN) nSNMP You can configure settings related to SNMP. TIPS • Depending on the SNMP settings, a short delay may occur before the SNMP is usable. (About 5 minutes) • Up to 16 alphanumeric letters and symbols can be used for the community name, user name and password. n SERVICE & SUPPORT (URL INFORMATION) You can display a specific URL in the URL INFORMATION field on the INFORMATION screen when an error occurs in the monitor. (See page 54.
Controlling the Monitor with a PC (LAN) [Advanced operation] Command-based control You can control the monitor using RS-232C commands (see page 43) via terminal software and other appropriate applications. In order to use this function, enable a connection to the monitor through Internet Explorer. Read the manual for the terminal software for detailed instructions. (1) Connect the PC to the monitor. 1. Specify the IP address and data port number and connect the PC to the monitor.
Troubleshooting If you are experiencing any problem with your display, before calling for service, please review the following troubleshooting tips. There is no picture or sound. • Is the power cord disconnected? (See page 14.) • Is the main power switch off? (See page 17.) • Is the monitor in standby mode (the power LED illuminating in orange)? (See page 17.) • Is an input mode selected that is appropriate for the input terminal to which the cable is connected? (See pages 24 to 25.
Troubleshooting Power LED flashes red. “STATUS [xxxx]” appears in the corner of the screen. • Hardware has a problem. Turn off the monitor and request repair from your SHARP dealer. (When STATUS ALERT is set to OSD & LED. This varies depending on the setting.) When “AUTO DIMMING” is displayed. • When the internal temperature of the monitor rises excessively, the brightness of the backlight automatically decreases in order to prevent a further temperature rise.
Specifications nProduct Specifications Model LCD component Max. resolution Max. colors Pixel pitch Viewing angle Screen active area Computer input signal Sync signal PN-80TC3A 80" Class [80 inch (203.2cm) diagonal] TFT LCD (pixels) 1920 x 1080 Approx. 1.06 billion colors 0.923 mm (H) × 0.923 mm (V) 176° right/left/up/down (contrast ratio ≥ 10) inch (mm) 69-3/4 (W) x 39-1/4 (H) (1771.2 x 996.3) Analog RGB (0.7 Vp-p) [75 Ω], DisplayPort 1.
Specifications nDimensional Drawings Note that the values shown are approximate values.
Specifications nPower management This monitor conforms to VESA DPMS. Both your video card and computer must support the same standard in order for the monitor’s power management function to work. DPMS: Display Power Management Signaling DPMS Screen Power consumption Hsync Vsync ON STATE Display 280 W Yes Yes No Yes Yes No No No STANDBY No display SUSPEND OFF STATE 6.0 W* * When CONNECT AUTO INPUT SELECT and NO SIGNAL AUTO INPUT SEL. are set to OFF.
Specifications nCompatible signal timing (AV) Screen resolution 1920 × 1080p 1920 × 1080i 1280 × 720p 720 × 576p 720 × 480p 640 × 480p(VGA) 720(1440) × 576i 720(1440) × 480i Frequency 24Hz 50Hz 59.94Hz 60Hz 50Hz 59.94Hz 60Hz 50Hz 59.94Hz 60Hz 50Hz 59.94Hz 60Hz 59.94Hz 60Hz 50Hz 59.
Specifications nD-sub input terminal (Mini D-sub 15 pin) No. Function Function Red video signal input 9 +5V 2 Green video signal input 10 GND 3 Blue video signal input 11 N.C. 4 N.C. 12 DDC data 5 GND 13 Hsync signal input 6 GND for red video signal 14 Vsync signal input 7 GND for green video signal 15 8 GND for blue video signal No. 66 No. 1 nHDMI input terminal (HDMI Connector) E nDisplayPort input (DisplayPort 20 pin) pins Function DDC clock pins No.
Mounting Precautions (For SHARP dealers and service engineers) • When installing, removing or moving the monitor, ensure that this is carried out by at least 4 people. • Be sure to use a wall-mount bracket designed or designated for mounting the monitor. • This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials such as plaster / thin plastic board / wood before starting installation.
Mounting Precautions (For SHARP dealers and service engineers) nRemoving the Tray Back of the tray (2) (1) Pinch the locking tabs (4 places) nAttaching the speaker covers Speaker cover attachment screws (M3) If you will use the monitor in a portrait orientation, the speaker cover is not used. nRemoving the tray mount fitting If you will use the monitor in a portrait orientation or will otherwise not use the tray, remove the tray mount fitting.
PN-80TC3A M EN17J(1)
