PN-R706 PN-R606 PN-R556 PN-R496 PN-R426 LCD MONITOR OPERATION MANUAL
Information on the Disposal of this Equipment and its Batteries IF YOU WISH TO DISPOSE OF THIS EQUIPMENT OR ITS BATTERIES, DO NOT USE THE ORDINARY WASTE BIN, AND DO NOT PUT THEM INTO A FIREPLACE! Used electrical and electronic equipment and batteries should always be collected and treated SEPARATELY in accordance with local law. Separate collection promotes an environment-friendly treatment, recycling of materials, and minimizing final disposal of waste.
IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DEAR SHARP CUSTOMER Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product. SAFETY PRECAUTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety.
SAFETY PRECAUTIONS (Continued) 19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment, dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below: • Use the specified batteries only. • Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the compartment. • Do not mix old and new batteries.
TIPS AND SAFETY INSTRUCTIONS - The TFT color LCD panel used in this monitor is made with the application of high precision technology. However, there may be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from an acute angle there may be uneven colors or brightness. Please note that these are not malfunctions but common phenomena of LCDs and will not affect the performance of the monitor.
MOUNTING PRECAUTIONS • This product is for use indoors. • A mounting bracket compliant with VESA specifications is required. • Since the monitor is heavy, consult your dealer before installing, removing or moving the monitor. • Mounting the monitor on the wall requires special expertise and the work must be performed by an authorized SHARP dealer. You should never attempt to perform any of this work yourself.
Contents IMPORTANT INFORMATION.............................................3 DEAR SHARP CUSTOMER...............................................4 SAFETY PRECAUTIONS...................................................4 TIPS AND SAFETY INSTRUCTIONS................................6 MOUNTING PRECAUTIONS.............................................7 Supplied Components......................................................8 Part Names........................................................................
Part Names [PN-R706/PN-R606] nFront view 23 nRear view 14 13 15 23 16 17 13 1 18 19 20 21 22 23 4* 13 5 23 6 2 7 [PN-R556/PN-R496/PN-R426] nFront view nRear view 8 3 9 14 10 11 12 15 16 17 13 1 18 19 20 21 22 13 4* 2 5 6 7 8 9 10 11 12 3 * How to pull out the power LED/remote control sensor Pull out Lever Store Power LED / Remote control sensor • Slide the lever on the rear of the monitor to pull out the power LED/remote control sensor.
Part Names 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. LCD panel Power button (See page 17.) Input button (See page 20.) Power LED (See page 17.) / Remote control sensor (See page 15.) AC input terminal (See page 13.) Main power switch (See page 13.) DisplayPort output terminal (See page 11.) HDMI1 input terminal (See page 12.) HDMI2 input terminal (See page 12.) DisplayPort input terminal (See page 12.) DVI-D input terminal (See page 12.) D-sub input terminal (See page 12.) Vents Speakers 15.
Connecting Peripheral Equipment 7 8 9 10 11 12 1 Caution • Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/ disconnecting cables. Also, read the manual of the equipment to be connected. • Be careful not to confuse the input terminal with the output terminal when connecting cables. Accidentally reversing cables connected to the input and output terminals may cause malfunctions and the other problems.
Connecting Peripheral Equipment 2. HDMI1 input terminal 3. HDMI2 input terminal • Use a commercially available HDMI cable (conforming to the HDMI standard). • Select the audio input terminal to be used in HDMI1 or HDMI2 of AUDIO SELECT on the SETUP menu. When HDMI is selected, connection to the audio input terminal is unnecessary. 4. DisplayPort input terminal • Use a commercially available DisplayPort cable. • Select the audio input terminal to be used in DisplayPort of AUDIO SELECT on the SETUP menu.
Connecting the Power Cord Caution • Use only the power cord supplied with the monitor. 1. Turn off the main power switch. 2. Plug the power cord (supplied) into the AC input terminal. 3. Plug the power cord (supplied) into the AC power outlet. Main power switch 1 AC input terminal Power cord (Supplied) 2 3 For power outlet Binding Cables The supplied cable clamps (affixing type) can be used to clamp the power code and cables connected to the back of the monitor.
Removing the Handles (PN-R706/PN-R606 only) The handles can be removed. Caution Handle Handle screws • The removable handles and handle screws are for use with this monitor. Do not use them for any other devices. • To attach handles, be sure to use the handles and handle screws which were removed from this monitor. • Be sure the handles are attached securely. • Do not attach the handle screws with the handles removed. Doing so may damage the inside of the monitor.
Attaching the logo sticker You can attach the supplied logo sticker on the monitor. Refer to the following example to attach the sticker as necessary. Example for landscape orientation Example for portrait orientation Preparing the Remote Control Unit Installing the batteries 1. Place your finger on the part marked with the ▲, and then pull the cover off. 2.
Preparing the Remote Control Unit [PN-R556/PN-R496/PN-R426] For the monitor in landscape orientation For the monitor in portrait orientation 10º 10º 9.8 feet (3m) Remote control sensor 9.8 feet (3m) 20º 9.8 feet (3m) Remote control sensor 10º 10º 9.8 feet (3m) 20º 10º10º 10º10º Remote control sensor out Point the remote control toward the remote control sensor on the front of the monitor. [PN-R706/PN-R606] For the monitor in landscape orientation 16.
Turning Power On/Off Caution • Turn on the monitor first before turning on the computer or playback device. • When switching the main power switch or the POWER button off and back on, always wait for at least 5 seconds. A short interval may result in a malfunction. Turning power on/off Press the POWER button to turn the power ON/OFF. You can also turn the power ON/OFF by pressing the MONITOR ON button/MONITOR OFF button on the remote control unit.
Turning Power On/Off nMode setting When the monitor is turned on for the first time after being shipped from the factory, the mode setting screen will be displayed. (1)Press or to select YES or NO. (2)Press the ENTER button. YES: • OPERATION MODE is set to MODE1. • OFF IF NO OPERATION is set to ON, and POWER SAVE MODE is set to ON. (These settings can not be changed.) • If there is no operation for 4 hours or more, the monitor automatically enters standby mode.
Basic Operation 5. VOLUME +/- (Volume adjustment) 1 11 12 13 2 Pressing + or - displays the VOLUME menu. VOLUME 15 Press + or - to adjust the volume of the sound. * If you do not press any buttons for about 4 seconds, the VOLUME menu automatically disappears. 6. INFORMATION Displays monitor information. INFORMATION1 3 14 4 5 6 15 16 17 7 8 9 18 19 20 10 LAN 1920x1080 2.
Basic Operation 12. OPTION Switch the input mode to OPTION. 13. DP (DisplayPort) Switch the input mode to DisplayPort. 14. SIZE (Screen size selection) The menu is displayed. Press or to select the screen size. (See page 21.) 15. PIP/PbyP Each time you press the button, PIP MODES switches in the following order: OFF → PIP → PbyP → PbyP2 → OFF. 16. BRIGHT +/- (Brightness adjustment) Pressing + or - displays the BRIGHT menu. BRIGHT 15 Press + or - to adjust the brightness.
Basic Operation nSwitching the screen size Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE Displays image so it fills the entire screen. ZOOM 1 The image is enlarged to fill the entire screen without changing the aspect ratio. The edges of the image may be cut off. ZOOM 2 Use this size if ZOOM 1 cuts off the subtitles. NORMAL Displays the image so it fills the screen without changing the aspect ratio.
Menu Items Displaying the menu screen Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 23 to 33 for details of each menu items. Caution • Do not turn the main power switch off while the menu items are being displayed. Doing so may initialize the settings. TIPS • The menu will differ depending on the input mode. • The menu screen will close automatically if no operation is performed for about 15 seconds.
Menu Items Menu item details The menu will differ depending on the input mode. nSCREEN You can move the menu screen display position each time the INFORMATION button is pressed. AUTO (D-SUB[RGB]) The CLOCK, PHASE, H-POS, and V-POS are automatically adjusted. Pressing the ENTER button performs adjustment. Use this automatic adjustment when you use the D-SUB[RGB] to display a computer screen for the first time or when you change the setting of the computer. (See page 33.
Menu Items nPICTURE You can move the menu screen display position each time the INFORMATION button is pressed. BRIGHT Adjusts the backlight brightness. CONTRAST Adjusts the difference between the bright and dark portions of the image. BLACK LEVEL Adjusts the entire brightness of the video signals. TINT Adjusts the hue. Selecting + changes the color towards green, and selecting - changes it towards magenta. COLORS Adjusts the color intensity. SHARPNESS Adjusts the sharpness of the image.
Menu Items ADVANCED AUTO (D-SUB[RGB]) The ANALOG GAIN and ANALOG OFFSET are automatically adjusted. Pressing the ENTER button performs adjustment. ANALOG GAIN (D-SUB[RGB]) Adjusts the bright portions of the video input signal. ANALOG OFFSET (D-SUB[RGB]) Adjusts the dark portions of the video input signal. NR Reduce the image noise. Setting a higher level reduces more noise. However, it may cause blurring on an image. RGB INPUT RANGE (DVI-D/HDMI/D-SUB[RGB]/DisplayPort/OPTION) Sets the RGB input signal range.
Menu Items nSETUP DATE/TIME SETTING Set the date and time. Press or to select the date and time, and press or Set the date in “Day/Month/Year” order. Set the time on a 24-hour basis. (Factory default) DATE/TIME FORMAT Sets the date/time display format. DATE...................MM/DD/YYYY, DD/MM/YYYY, YYYY/MM/DD (YYYY: Year, MM: Month, DD: Day) TIME....................Select 12- or 24-hour time. SCHEDULE (See page 32.) You can turn the power on/off and change the screen brightness at a specified time.
Menu Items START INPUT MODE You can set the input mode that will be in effect when the power is turned on. When this is set to LAST INPUT MODE, the input mode when the power was last turned off will appear. COMMUNICATION SETTING RS-232C/LAN SELECT Selects the method with which to control the monitor from the computer. BAUD RATE Selects the communication speed used for RS-232C communication. LAN SETUP Configures the settings to control the monitor from the computer via LAN. (See page 47.
Menu Items nMONITOR PORTRAIT/LANDSCAPE INSTALL LANDSCAPE.......Landscape orientation PORTRAIT..........Portrait orientation HORIZONTAL INSTALLATION OFF.....................Portrait/landscape installation UPWARD.............The display screen faces up. DOWNWARD......The display screen faces down. ROTATE 180° If video is upside down when the monitor is installed in portrait orientation, you can rotate the video 180 degrees. Interlaced signals may not be displayed properly.
Menu Items nMULTI/PIP MULTI ENLARGE (See page 31.) Sets whether or not to use the enlarge function. ADVANCED (ENLARGE) ENLARGE H / ENLARGE V ........... Sets the number of screen splits (number of monitors) in the horizontal/vertical direction used for the enlargement. ENLARGE-POS ........... Specify the split screen to be displayed when the enlargement function is used. H-POS / V-POS ...........Adjust the horizontal/vertical position of the enlarged screen.
Menu Items nOTHERS SCREEN MOTION PATTERN Residual images are reduced by moving the screen. OFF.................. SCREEN MOTION function is disabled. PATTERN1....... The whole screen moves vertically and horizontally. PATTERN2....... A black screen spreads from the bottom of the screen and then shrinks to the bottom of the screen. If the monitor is installed in the portrait orientation, a black screen spreads from the right end of the screen and then shrinks to the right end of the screen. PATTERN3.......
Menu Items nDual screen display nEnlarge You can display two screens simultaneously. Set this function with PIP MODES of PIP/PbyP in the MULTI/ PIP menu. PIP A sub screen is displayed inside a main screen. Main screen Sub screen PbyP Main screen Sub screen PbyP2 Main screen Sub screen • You can align several monitors and integrate them into a single large screen to display. • Up to 5 monitors can be aligned in both the horizontal and vertical directions.
Menu Items nSCHEDULE You can set the time to switch the monitor on and off. Set this function with SCHEDULE in the SETUP menu. (See page 26.) D-SUB[RGB] SCHEDULE – –/– –/– – – – (2) No.
Menu Items nAbout remote control numbers If there is the chance that you will operate the wrong set from the remote control, you can prevent this from happening by changing the remote control numbers to different values in advance. You have to make changes on the monitor and on the remote control. TIPS • You can set remote control numbers to values from 0 to 9. • When the remote control batteries become exhausted and when you replace the batteries, the number on the remote control may be reset to 0.
Initialization (Reset)/Functional Restriction Setting (FUNCTION) You can reset the settings to the factory default settings or restrict operations. 1. Press the FUNCTION button, and then press the MENU button within 10 seconds. ▲ OFF ▲ ▲▲▲▲▲▲ UNLOCKED ON 1 ON LED OFF MONITOR ▲▲▲▲ ▲ ▲ 1 ▲ ALL RESET ADJUSTMENT LOCK ADJUSTMENT LOCK TARGET RS-232C/LAN OSD DISPLAY LED TEMPERATURE ALERT STATUS ALERT POWER BUTTON EXTERNAL CONTROLLER INPUT SIGNAL RESPONSE LEVEL ▲ FUNCTION OK:[ENTER] END:[RETURN] 2.
Controlling the Monitor with a PC (RS-232C) You can control this monitor from a PC via RS-232C (COM port) on the PC. You can also connect multiple monitors via a daisy chain by using a PC. By assigning ID numbers to each monitor (see page 36), you can make input mode selection/adjustment or can check the status of a specific monitor. TIPS • To control the monitor via RS-232C, set RS-232C/LAN SELECT to RS-232C. • You cannot use RS-232C and LAN control simultaneously.
Controlling the Monitor with a PC (RS-232C) nResponse code format When a command has been executed correctly O K Return code (0DH, 0AH) A response is returned after a command is executed.
Controlling the Monitor with a PC (RS-232C) nCommands for ID control The command examples shown on this page assume the following connection and ID number set up. ID number: 1 ID number: 2 ID number: 3 ID number: 4 IDST ��������. A monitor receiving this command sets its own ID number in the parameter field. Example: IDST0001 OK 001 ← The ID number of this monitor is set to 1. IDLK ��������The parameter of this command sets the ID number of the monitor.
Controlling the Monitor with a PC (RS-232C) nRepeater control This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. You can use Repeater control function without assigning ID numbers. [Example] Set 1 Set 2 Set 3 Set 4 Setting of the GAMMA user data nTo transfer the GAMMA user data Use the user data transfer commands (UGRW, UGGW and UGBW).
Controlling the Monitor with a PC (RS-232C) RS-232C command table How to read the command table Command: Command field (See page 35.) Direction: W When the “Parameter” is set in the parameter field (see page 35), the command functions as described under “Control/Response Contents”. R The returned value indicated under “Reply” can be obtained by setting “????”, “ ?” or “???+” (repeater control) in the parameter field. (See page 35.) Parameter: Parameter field (See page 35.
Controlling the Monitor with a PC (RS-232C) SCREEN menu Command Direction Auto ASNC W CLOCK CLCK WR Function PHASE positioning size RESOLUTION SETTING Reply Control/Response contents 1 When the input mode is D-SUB[RGB]. 0-1200 0-1200 When the input mode is D-SUB[RGB]. Varies depending on the signal. PHSE WR 0-63 Position of the longest direction HPOS WR 0-100 0-100 0-800 on D-SUB[RGB]. Varies depending on the signal.
Controlling the Monitor with a PC (RS-232C) PICTURE menu Command Direction BRIGHT VLMP WR 0-31 0-31 CONTRAST CONT WR 0-60 0-60 BLACK LEVEL BLVL WR 0-60 0-60 TINT TINT WR 0-60 0-60 COLORS COLR WR 0-60 0-60 SHARPNESS SHRP WR 0-24 0-24 BMOD WR 0 0 STD 2 2 VIVID 3 3 sRGB (sRGB cannot be used when input mode is D-SUB[COMPONENT].
Controlling the Monitor with a PC (RS-232C) AUDIO menu Command Direction TREBLE AUTR WR BASS AUBS WR -5-5 -5-5 BALANCE AUBL WR -10-10 -10-10 RESET ARST W Function Parameter Reply -5-5 Control/Response contents * -5-5 ○ 3 - SETUP menu Command Direction Date/time setting DATE WR DATE FORMAT DTFT WR TIME FORMAT TMFT WR SCHEDULE SC01SC08 WR SCHEDULE BRIGHTNESS SB01SB08 WR LANG WR Function LANGUAGE Parameter Reply AABBCCDDEE 0-2 0-1 ABCDEFFGGH 0-31 0-1 0: 24-H
Controlling the Monitor with a PC (RS-232C) Command Direction ID No. SET IDST W ID NO. SETTING (ONCE) IDSL W 1-255 ID NO. SETTING (SUBSEQUENT) IDLK W 1-255 ID CHECK IDCK W 0 ID DISPLAY IDDP W 0-2 Function ID SETTING Parameter Reply Control/Response contents 0-255 R 0-255 Clears the ID number if one has been designated. Set a monitor’s ID number to send a command. This ID number is effective for the next and all subsequent commands after this command.
Controlling the Monitor with a PC (RS-232C) MULTI/PIP menu Command Direction ENLARGE ENLG WR ENLARGE MODE EMAG WR 1-4 EMHV WR 12(21)-55 IMAGE POSITION (M x N) EPHV WR 11-55 IMAGE POSITION (2 x 2) EPOS WR 0-3 IMAGE POSITION (3 x 3) EPOS WR 0-8 0-8 IMAGE POSITION (4 x 4) EPOS WR 0-15 0-15 IMAGE POSITION (5 x 5) Function ENLARGED SCREEN POSITIONING BEZEL WIDTH Reply 0-1 Control/Response contents * 0-1 0: OFF, 1: ON 1-4 1: 2 x 2, 2: 3 x 3, 3: 4 x 4, 4: 5 x 5 12(21)-55 1 x 2
Controlling the Monitor with a PC (RS-232C) Function PIP MODES PIP SIZE PIP POS Command Direction MWIN WR MPSZ WR The longest direction MHPS W The shortest direction MVPS PIP POS LD+SD BATCH Parameter Reply 0-3 1-64 W 1-64 0-100 0-100 R MPOS * 0-100 R W Control/Response contents 0-3 0: OFF, 1: PIP, 2: PbyP, 3: PbyP2 0-100 0-100,0-100 R Specify the position in MPOSxxxyyy format. (xxx: Longer side, yyy: Shorter side position) 0-100,0-100 Returns a response in (xxx,yyy) format.
Controlling the Monitor with a PC (RS-232C) Others Command Direction SCREEN SIZE WIDE WR 1-5 VOLUME VOLM WR 0-31 0-1 Function MUTE AUDIO INFORMATION Parameter Reply Control/Response contents 1-5 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2 0-31 MUTE WR MODEL INF1 R Value SERIAL NO SRNO R Value DSTA R TEMPERATURE SENSOR 0-1 0: OFF, 1: ON * ○ - 0 Internal temperature normal 1 Internal temperature abnormal has occurred and the monitor is in standby mode 2 Internal tempe
Controlling the Monitor with a computer (LAN) Your monitor can be connected to a LAN allowing you to control it from a computer on the LAN. You can also configure the monitor to send e-mail notification when it has a problem. The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through). Network (LAN) Settings to connect to a LAN Set the monitor’s IP address and subnet mask to match the settings of your LAN.
Controlling the Monitor with a computer (LAN) nTo set from a computer When the monitor is connected to a computer, LAN settings can be configured via computer. Set up process (1) Connect your monitor to a computer (2) Specify the computer’s IP address (3) Configure the monitor’s LAN settings 7. Temporarily change the IP address and subnet mask. To access the monitor as it is shipped from the factory, set as follows. • IP Address : 192.168.150.1 • Subnet Mask : 255.255.255.
Controlling the Monitor with a computer (LAN) 6. Click on “LAN SETUP” under NETWORK. Controlling with a computer n Basic operation You use the web browser on a computer on the LAN to control the monitor. 1. Launch the web browser on the computer. 2. In the “Address” box, type “http://” followed by your monitor’s IP address followed by “/”, then press the Enter key. You can confirm the IP address with the INFORMATION function. 7. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc.
Controlling the Monitor with a computer (LAN) nINFORMATION nADJUSTMENT Information about this monitor appears. You can adjust these settings which are also available on the monitor’s menu. • SCREEN (See page 23.) • PICTURE (See page 24.) • PICTURE (ADVANCED) (See page 25.) • AUDIO (See page 25.) • SETUP (See page 26.) • MONITOR (See page 28.) • OTHERS (See page 30.) • SCHEDULE (See page 32.) • MULTI (See page 29.) • PIP/PbyP (See page 29.) • FUNCTION (See page 34.
Controlling the Monitor with a computer (LAN) nNETWORK (LAN SETUP) This screen allows you to set the settings necessary when the monitor is connected to a LAN. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to “ON”. To set the address manually, set this to “OFF”. IP ADDRESS If the DHCP CLIENT is set to “OFF”, specify an IP address. SUBNET MASK If the DHCP CLIENT is set to “OFF”, specify the subnet mask.
Controlling the Monitor with a computer (LAN) nNETWORK (GENERAL) This screen allows you to specify the general LAN settings. MONITOR NAME Specify a name for this monitor as it should appear on the web browser screen. AUTO LOGOUT TIME Specify the time (in minutes) to elapse before automatically disconnecting this monitor from the network. Specify in minutes from 1 to 65535. A value of ‘0’ will disable this function. DATA PORT Specify the TCP port number to use for exchanging data with the monitor.
Controlling the Monitor with a computer (LAN) nMAIL (RECIPIENT) This screen allows you to specify the recipients of the e-mail sent periodically or when the monitor has an error. RECIPIENT E-MAIL ADDRESSES Specify the e-mail addresses to send error notification e-mail to. CONDITION Specify the conditions to send mails. When you check PERIODICAL, specify the date and time to send the mails in the PERIODICAL setting. CONFIRMATION Sends test e-mail.
Controlling the Monitor with a computer (LAN) nSNMP You can configure settings related to SNMP. Caution • After you set SNMP, click [Switch the main power of monitor off and on now.] or turn off the monitor and then turn it on again with the main power switch. When the monitor restarts, wait about 30 seconds and then start the next operation. • If the IP address is changed while the SNMP function is operational, turn off the monitor and then turn it on again with the main power switch.
Controlling the Monitor with a computer (LAN) nCrestron Connected 1. Display below information. • Display Name Display the Crestron Connected control menu. Control Menu 5 • Mac Address • Resolution 2. Display below status. 1 • Power Status • Input 2 4 Help 3 Sends or receives messages to the administrators who uses “Crestron Connected”. 1. Operate below functions. • Power…….. Turn the power ON/OFF. • Mute………. Turns off the volume temporarily. • Vol-/Vol+...... Adjust the volume of the sound.
Troubleshooting If you are experiencing any problem with your display, before calling for service, please review the following troubleshooting tips. There is no picture or sound. • Is the power cord disconnected? (See page 13.) • Is the main power switch off? (See page 17.) • Is the monitor in standby mode (the power LED illuminating in orange)? (See page 17.) • Make sure correct input mode is selected. (See page 20.
Troubleshooting The Power LED is flashing in red and green alternately. When “TEMPERATURE” is displayed in the corner of the screen. • When the internal temperature of the monitor rises excessively, the brightness of the backlight decreases automatically in order to prevent high-temperaturerelated problems. When this occurs, “TEMPERATURE” is displayed on the screen and the Power LED flashes red and green alternately. (When TEMPERATURE ALERT is set to OSD & LED. This varies depending on the setting.
Specifications nProduct Specifications Model LCD component Max. resolution Max. colors Pixel pitch Max.
Specifications Model LCD component Max. resolution Max. colors Pixel pitch (pixels) Max.
Specifications nDimensional Drawings Note that the values shown are approximate values. [PN-R706] Unit: inch [mm] 3-3/16 [81] VESA holes * 62-3/16 [1579] 2-9/16 [65] 31-1/16 [789.5] 7-7/8 [200] 7-7/8 [200] 15/16 [24] 3/4 [19] 3/4 [19] Opening height (34-1/4 [870]) 18-1/16 [459] 7-7/8 [200] 36-1/8 [918] 7-7/8 [200] Opening width (60-11/16 [1541]) 15/16 [24] [PN-R606] Unit: inch [mm] 2-13/16 [72] 2-3/8 [60] VESA holes * 53-1/8 [1349] 26-9/16 [674.
Specifications [PN-R556] Unit: inch [mm] 2-1/4 [57] VESA holes * 48-7/16 [1231] 7-7/8 [200] 7-7/8 [200] 5/16 [7.8] 3/16 [5] 24-1/4 [615.5] 7-7/8 [200] 5/16 [7.8] 5/16 [7.8] Opening width (47-7/8 [1215.4]) Opening height (27 [686.4]) 13-13/16 [351] 7-7/8 [200] 27-5/8 [702] 1/16 [2] 5/16 [7.8] 11/16 [17] 2-11/16 [69] [PN-R496] Unit: inch [mm] 2-1/4 [57] VESA holes * 43-1/8 [1095] 7-7/8 [200] 5/16 [7.8] 3/16 [5] 21-9/16 [547.5] 7-7/8 [200] 5/16 [7.8] 7-7/8 [200] 5/16 [7.
Specifications nPower management This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in order for the monitor’s power management function to work. DMPM: Digital Monitor Power Management DPMS: Display Power Management Signaling DPMS Screen ON STATE Display STANDBY SUSPEND OFF STATE No display Power consumption*1 230 W 190 W 175 W 155 W 135 W 2.5 W*2 2.5 W*2 2.5 W*2 2.5 W*2 2.
Specifications nCompatible signal timing (AV) Screen resolution 1920 × 1080p Frequency 24Hz 50Hz 59.94Hz 60Hz 50Hz 59.94Hz 60Hz 50Hz 59.94Hz 60Hz 50Hz 59.94Hz 60Hz 59.94Hz 60Hz 50Hz 59.94Hz 60Hz 1920 × 1080i 1280 × 720p 720 × 576p 720 × 480p 640 × 480p(VGA) 720(1440) × 576i 720(1440) × 480i nHDMI input terminal pins Function Component Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes nD-sub input terminal pins (HDMI Connector) No.
Specifications nRS-232C output terminal pins nDVI-D input terminal pins (DVI-D 24 pin) No. Function No. (D-sub 9 pin) Function No. Function 13 N.C. 1 N.C. 6 N.C. 2 TMDS data 2+ 14 +5V 2 Received data 7 N.C. 3 TMDS data 2/4 shield 15 GND 3 Transmitted data 8 N.C. 4 N.C. 16 Hot-plug detection 4 N.C. 9 N.C. 5 N.C. 17 TMDS data 0- 5 GND 6 DDC clock 18 TMDS data 0+ 7 DDC data 19 TMDS data 0/5 shield 8 N.C. 20 N.C. 9 TMDS data 1- 21 N.C.
Mounting Precautions (For SHARP dealers and service engineers) • When installing, removing or moving the monitor, ensure that this is carried out by at least 3 people. (PN-R556/PN-R496/PN-R426: at least 2 people.) • Be sure to use a wall-mount bracket designed or designated for mounting the monitor. • This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials such as plaster / thin plastic board / wood before starting installation.
PN-R706-R606-R556-R496-R426 Me EN17C(1)
