Operation Manual

ManualsBrandsSharp ManualsSolarPNVC651B

Disposal of Old Equipment and Batteries Only for European Union and countries with recycling systems

The above mark is in compliance with the Waste Electrical and Electronic Equipment

Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose the

equipment including any spent or discarded batteries as unsorted municipal waste, but use

the return and collection systems available. If the batteries or accumulators included with

this equipment display the chemical symbol Hg, Cd, or Pb, then it means that

the battery has a heavy metal content of more than 0.0005% Mercury, or more than

0.002% Cadmium or more than, 0.004% Lead.

Note for the battery symbol (bottom symbol): This symbol might be used in

combination with a chemical symbol. In this case it complies with the requirement set by

the Directive for the chemical involved.

Summary of content (26 pages)

PAGE 1
Disposal of Old Equipment and Batteries Only for European Union and countries with recycling systems The above mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries as unsorted municipal waste, but use the return and collection systems available.
PAGE 2
IMPORTANT INFORMATION WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. FOR CUSTOMERS IN U.K. IMPORTANT The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW: Earth BLUE : Neutral BROWN: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markins identifying the terminals in your plug proceed as follows.
PAGE 3
DEAR SHARP CUSTOMER Thank you for your purchase of a SHARP interactive monitor. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product. SAFETY PRECAUTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety.
PAGE 4
SAFETY PRECAUTIONS (Continued) 15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in fire, electric shock and/or other danger. 16.
PAGE 5
SAFETY PRECAUTIONS (Continued) Especially for child safety  Don’t allow children to climb on or play with the monitor.  Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.  Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.
PAGE 6
MOUNTING PRECAUTIONS          This product is for use indoors. A mounting bracket compliant with VESA specifications is required. Since the monitor is heavy, consult your dealer before installing, removing or moving the monitor. Mounting the monitor on the wall requires special expertise and the work must be performed by an authorized SHARP dealer. You should never attempt to perform any of this work yourself.
PAGE 7
Content Table Caution ................................................................................................................................. 2 System Features.................................................................................................................. 9 PACKING LIST ....................................................................................................................10 INTRODUCTION .................................................................................
PAGE 8
NOTE Depending on the model you have bought, the appearance of your INTERACTIVE MONITOR may not be the same as the one displayed in this manual. As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
PAGE 9
System Features Model Name Installation LCD Panel Video PN-VC651B Landscape Edge 1920 × 1080 pixels 1.07 B 0.744 mm 360cd/m² 4000:1 178˚/ 178˚ 1428.48(H)x803.52(V)(mm) (56.24" x 31.63") 8 ms (Gray to Gray, Ave.) IR Touch Screen (6-point simultaneous touch screen support) USB 6 points 4mm anti-glare glass. 4mm tempered, anti-reflective glass(optional) HDMI1.
PAGE 10
PACKING LIST Remote Controller x 1 Additional battery x1 Power Cord x 2 (Euro / UK) HDMI Cable x 1 USB Cable Touch Screen Pen x 1 INTRODUCTION This instruction manual is intended to help you to get the best out of " INTERACTIVE MONITOR " Chapter 1 Introduction to your INTERACTIVE MONITOR Chapter 2 Using your INTERACTIVE MONITOR . Instructions for using the and its functions. Chapter 3 Power management. Information about power management. Chapter 4 Addition of other devices to your INTERACTIVE MONITOR.
PAGE 11
Signs used in this manual Some words and phrases are written in a different format to get your attention. Note: It is being used to put emphasis on useful information and critical points regarding the product . Important! Important instructions are to be read carefully in order to prevent any damage to yourself, stored data and computer parts. SAFETY PRECAUTIONS Power plug must be at a point that can be easily accessible and close to product.
PAGE 12
Cleaning Important! Disconnect your from the power supply before cleaning it. Do not clean your INTERACTIVE MONITOR while it is switched on. Use a soft and damp cloth to clean the surface of. Do not use chemical cleaners to clean the screen. Do not apply cleanser directly on your computer. Vent holes of your Vent holes on the cabin of your INTERACTIVE MONITOR ensures stable performance of your computer without overheating. Do not block these openings in any way.
PAGE 13
CHAPTER 1: INTRODUCTION TO INTERACTIVE MONITOR Congratulations for buying our INTERACTIVE MONITOR 65”(165cm) (165cm)/165cm ! We believe that you will be extremely satisfied with this and hope that you will have pleasant and productive times with your INTERACTIVE MONITOR . Your INTERACTIVE MONITOR provides a modern design that is compatible with most working conditions by combining a 65”(165cm) (165cm)/165cm TFT-LCD monitor, touch screen and a desktop computer.
PAGE 14
CHAPTER 2: USING AND ITS FUNCTIONS. Panel Panel type Active area Visual Horizontal angle Vertical Max. brightness Max. contrast Response time Max. resolution H - frequency V - frequency TFT LCD 1428.48 (H) x 803.52 (V) 178° 178° 360 cd/m2 4000:1 8 ms G2G 1920 * 1080 60 KHz ~ 73 KHz 47Hz ~ 63Hz (typical: 60Hz) Controlling the Monitor with a PC (RS-232C) You can control this interactive monitor from a PC via RS-232C (COM port) on the PC.
PAGE 15
Command field (12 byte Hexadecimal) Parameter field (1 byte Hexadecimal) Example1: Volume set command: BE EF 03 06 00 31 D3 03 00 01 20 01 15 This command is used for setting volume value as 21 out of 100. Example2: Backlight get command: BE EF 03 06 00 89 D2 02 00 03 20 00 00 This command is used for getting backlight value. Be sure that the command include exactly 13 Bytes data.  Response Code 3 type of response codes are exist.
PAGE 16
 Compatible signal timing (PC) Screen Resolution Hsync Vsync Dot frequency Digital HDMI VESA 31.5kHz 35.1kHz 37.9kHz 48.4kHz 44.7kHz 65.5kHz 48.3kHz 60Hz 56Hz 60Hz 60Hz 60Hz 60Hz 60Hz 25.175MHz 36.0MHz 40.0MHz 65.0MHz 74.4MHz 148.5MHz 64.13MHz Yes*1*2 Yes Yes Yes Yes Yes Yes 640x480 800x600 Wide Sun*4  1024x768 1280x720 1920x1080 1024x768 Compatible signal timing (AV) Screen resolution 1920x1080P 1280x720P 720x576P 720x480P 640x480(VGA) Frequency 50Hz 59.94Hz 60Hz 50Hz 59.
PAGE 17
 RS232 Command Table Function Name OPS Power Source Backlight Volume Screen Auto Adjust Keypad Lock Remote Controller Lock OSD Menu Contrast Monitor Mute Auto Position Color Temperature Clock Phase H-Position V-Position Color Get Gain R Color Get Gain G Color Get Gain B Function Type Command Data (HEX) Additional Information OFF ON GET OPS HDMI VGA BE EF BE EF BE EF BE EF BE EF BE EF 03 03 03 03 03 03 06 00 06 00 06 00 06 00 06 00 06 00 2A D3 BA D2 19 D3 FE D2 0E D2 6E D2 01 0
PAGE 18
Important! Install the sound drivers included in your system before using the sound function of your “ INTERACTIVE MONITOR ” In case of any sound distortions during recording, please decrease microphone volume. The methods of playing and recording sound depend on the operating system in use. Please refer to the instructions in your operating system’s support points for these methods. Function Buttons and Remote Controller There are 7 function buttons on “ INTERACTIVE MONITOR ” .
PAGE 19
CAUTION : RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Used correctly, domestic batteries are a safe and dependable source of portable power. Problems can occur if they are misused or abused resulting in leakage or, in extreme cases, fire or explosion. Here are some simple guidelines to safe battery use designed to eliminate any such problems.
PAGE 20
4.1.1. Touch screen Installation instructions The INTERACTIVE MONITOR is supplied with USB Stick which contains drivers and the Touch Service calibration application. 4.1.2. Touch screen Installation instructions 1. Double-click the installation file of "setup.exe" 2. To exit the installation, please click "Cancel"; to continue, click "Next", directly go to step.
PAGE 21
3. Start the installation by clicking "Install". 4. When completed, click "Finish" and exit. 5.
PAGE 22
CALIBRATING THE TOUCH SCREEN Function Description 1) The coordinates of the touch panel and display screen should be accurately matched by calibration. 2) When will calibration be needed? a) The first time you have installed touch panel bundled software. b) Inconsistency occurred between the mouse and your finger action. c) After changing the touch panel or monitor. d) Having moved the touch panel or there is a change in monitor resolution.
PAGE 23
3) Having touched the four calibration points, a dialogue box will pop up. Click "Yes" to save the calibration data and "No" not to. If you don’t click yes or no within 10s, you will automatically exit the calibration process without saving the data.
PAGE 24
CHAPTER 3: • Turn on the monitor first before turning on the computer or playback device. Troubleshooting If you are experiencing any problem with your display, before calling for service, please review the following troubleshooting tips. Computer resolution changes automatically. There is no picture or sound. • If you turn the power switch off and then back on again connecting the computer with a graphic card, the resolution may change to 640 x 480.
PAGE 25
- When touch pens are moved near each other. The monitor makes a cracking sound. • You may occasionally hear a cracking sound from the monitor. This happens when the cabinet slightly expands and contracts according to change in temperature. This does not affect the monitor’s performance. - When a pen is held at an angle while writing. Power LED flashes red. • The monitor has no signal input. If signal input is connected, the monitor will restart(LED is off) and display the picture.
PAGE 26
Specifications  Dimensional Drawings Note that the values shown are approximate values. When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method. SHARP recommends using M6 screws and tighten the screws. Mounting Precautions (For SHARP dealers and service engineers)    When installing, removing or moving the monitor, ensure that this is carried out by at least 3 people.