Introduction MODEL PG-F320W Quick Start DATA PROJECTOR Setup OPERATION MANUAL Connections Basic Operation Useful Features Appendix
IMPORTANT • For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information. • Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 11. ii Model No.: Serial No.
SPECIAL NOTE FOR USERS IN THE U.K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
The supplied CD-ROM contains operation instructions in English, German, French, Spanish, Italian, Dutch, Swedish, Portuguese, Chinese and Korean. Carefully read through the operation instructions before operating the projector. Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Spanisch, Italienisch, Niederländisch, Schwedisch, Portugiesisch, Chinesisch und Koreanisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.
Introduction Introduction Before using the projector, please read this operation manual carefully. ENGLISH There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. 1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase. 2.
INFORMATION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications.
Introduction How to Read this Operation Manual ■ The specifications are slightly different, depending on the model. However, you can connect and operate all models in the same manner. • In this operation manual, the illustration and the screen display are simplified for explanation, and may differ slightly from the actual display.
Contents Preparing Introduction Useful Features How to Read this Operation Manual .... 3 Contents ............................................... 4 IMPORTANT SAFEGUARDS ............... 6 How to Access the PDF Operation Manuals ............................................ 10 Accessories ........................................ 11 Part Names and Functions ................. 12 Operating with the Remote Control .... 33 Projector ............................................... 12 Rear View ..................
Introduction Setting up the Projector Network Environment (“Network” menu) ........ 49 Setting a Password .............................. 49 DHCP Client Setting ............................. 50 TCP/IP Setting ...................................... 50 Confirming the Projector Information ... 50 Troubleshooting with the “Help” Menu ...................................... 51 Utilizing the “Help” Menu Functions .... 51 Reference Appendix Maintenance .......................................
IMPORTANT SAFEGUARDS CAUTION: Please read all of these instructions before you operate this product and save these instructions for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing. 1.
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 16. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 17.
Observe the following safeguards when setting up your projector. Caution concerning the lamp unit ■ Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for replacement. See “Replacing the Lamp” on page 57.
■ If you are not to use the projector for a long time or before moving the projector, make certain you unplug the power cord from the wall outlet, and disconnect any other cables connected to it. ■ If the power cord is unplugged while the cooling fan is running, some parts of the projector may still be hot. Use caution when handling the projector. ■ Do not carry the projector by holding the lens. ■ When storing the projector, ensure you attach the lens cap to the projector. (See page 12.
How to Access the PDF Operation Manuals PDF operation manuals in several languages are included in the CD-ROM. To utilize these manuals, you need to install Adobe® Reader® on your computer (Windows® or Macintosh®). Please download Adobe® Reader® from the Internet (http://www.adobe.com). Accessing the PDF Manuals For Windows®: 1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “My Computer” icon. 3 Double click the “CD-ROM” drive.
Introduction Accessories Supplied accessories Two R-6 batteries RGB cable Lens cap (attached) (“AA” size, UM/SUM-3, (10' (3.0 m)) HP-7 or similar) Remote control DIN-D-sub RS-232C adaptor (5 57/64" (15 cm)) Power cord* (1) (2) (3) Storage case (4) For U.S. and For Europe, For U.K. and For Australia, New Canada, etc. except U.K. Singapore Zealand and Oceania (6' (1.8 m)) (6' (1.8 m)) (6' (1.8 m)) (6' (1.
Part Names and Functions Numbers in Z refer to the main pages in this operation manual where the topic is explained. Projector Top View Power indicator 26 55 STANDBY/ON button For turning the power on and putting the projector into standby mode. 26 ENTER button For setting items selected or adjusted on the menu. 39 26 55 Lamp indicator 55 Temperature warning indicator 30 VOL (Volume) buttons (–O/Q+) For adjusting the speaker sound level. 30 INPUT buttons (P/R) For switching input mode.
Rear View Terminals MONITOR OUT terminal 23 (Output terminal for computer RGB, component and DVI analog signals. Shared for COMPUTER/COMPONENT and DVI-I) Terminal for connecting a monitor. DVI-I input terminal 21 Terminal for DVI 22 digital, computer RGB, and component signals. 22 S-VIDEO input terminal Terminal for connecting video equipment with an S-video terminal. USB terminal Terminal connecting with the USB terminal on the computer for using the supplied remote control as the computer mouse.
Part Names and Functions (Continued) STANDBY button 26 For putting the projector into the standby mode. COMPUTER, DVI, 30 S-VIDEO, VIDEO buttons For switching to the respective input modes. BREAK TIMER button 33 For displaying the break time. MAGNIFY buttons 34 For enlarging/reducing part of the image. PAGE UP/PAGE 35 DOWN buttons Same as the [Page Down] and [Page Up] keys on a computer keyboard, when with the USB connection (using a USB cable or the optional remote receiver).
1 Pull down the tab on the cover and remove the cover towards the direction of the arrow. 2 Insert the batteries. 3 Insert the lower tab of the cover into the opening, and lower the cover until it clicks in place. Introduction Inserting the Batteries • Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment. Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Quick Start This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step. Setup and Projection In this section, connection of the projector and the computer is explained using one example.
4. Adjust the projected image with the Setup Guide 1 After the projector turns on, the Setup Guide appears. (When “Setup Guide” is set to “On”. See page 45.) 2 Follow the steps in the Setup Guide and adjust the focus, picture size, and height (angle). 3 After adjusting the focus, height (angle) and picture size, press ENTER to finish the Setup Guide. Quick Start _PP. 27, 28 5. Correct trapezoidal distortion Correcting trapezoidal distortion using Keystone Correction.
Setting up the Projector Setting up the Projector For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. (See page 29.) Standard Setup (Front Projection) ■ Place the projector at the required distance from the screen according to the desired picture size. (See page 20.
Projection (PRJ) Mode The projector can use any of the 4 projection modes shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-ADJ” menu. See page 45.
Setting up the Projector (Continued) Screen Size and Projection Distance 16:10 Signal Input (Normal Mode) Picture (Screen) size Diag. [χ ] Width Height Projection distance [L] Minimum [L1] Maximum [L2] Distance from the lens center to the bottom of the image [H] 300" (762 cm) 646 cm (254") 404 cm (159") 8.8 m (28' 11") 10.3 m (33' 8") 32 cm (12") 250" (635 cm) 538 cm (212") 337 cm (132") 7.4 m (24' 2") 8.6 m (28' 1") 27 cm (10") 200" (508 cm) 431 cm (170") 269 cm (106") 5.9 m (19' 6") 6.
Connecting the Projector to Other Equipment Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off the equipment to be connected. After making all connections, turn on the projector and then the other pieces of equipment. When connecting a computer, ensure that it is the last equipment to be turned on after all the connections are made.
Connecting the Projector to Other Equipment (Continued) Equipment Video equipment Terminal on Cable connected equipment HDMI to DVI cable HDMI (commercially available) output terminal DVI digital output terminal Terminal on the projector DVI-I DVI Digital cable (commercially available) 3 RCA to mini D-sub 15 pin cable (optional, AN-C3CP2) COMPUTER/ COMPONENT S-video output terminal S-video cable (commercially available) S-VIDEO Video output terminal Video cable (commercially available) VIDEO C
Equipment Audio equipment Terminal on connected equipment Cable ø3.5 mm stereo or mono audio cable ø3.5 mm audio output (commercially available or available as Sharp service part QCNWGA038WJPZ) terminal RCA audio output terminal Terminal on the projector AUDIO 1 RCA audio cable (commercially available) AUDIO 2 Cables for a camera or a video game Audio output terminal Monitor RGB input terminal ø3.5 mm audio input terminal RCA audio input terminal MONITOR OUT ø3.
Controlling the Projector by a Computer When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS232C adaptor and an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector. Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for “RS-232C Specifications and Commands”.
When connecting to the LAN terminal using a LAN cable TX/RX LED (yellow) Illuminates when transmitting/receiving data. LINK LED (green) Illuminates when linked. * To ensure safety, do not connect the LAN terminal with any cables that may cause excessive voltage such as a telephone line. Hub or Computer To LAN terminal Connections LAN cable (Category 5 type, commercially available) Note • When connecting to a hub, use a straight-through Category 5 (CAT.5) type cable (commercially available).
Turning the Projector On/Off Info Turning the Projector on Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages 21 to 25.) Remove the lens cap and press STANDBY/ON on the projector or ON on the remote control.
Image Projection Setup Guide screen About the Setup Guide After turning on the projector, the Setup Guide screen appears to assist you with projector setup. Guidance items 1 FOCUS 2 HEIGHT ADJUST 3 ZOOM Press ENTER to exit the Setup Guide screen. Note • The Setup Guide screen automatically highlights the items in the following order: 1 FOCUS 4 ENTER 2 HEIGHT ADJUST 3 ZOOM However, you can adjust the focus, height (angle), or zoom regardless of the highlighted item.
Image Projection (Continued) 3 Adjusting the Height The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector. When the screen is above the projector, the projection image can be made higher by adjusting the projector. 1 Lift the projector to adjust its height while lifting the HEIGHT ADJUST lever. 2 Remove your hands from the HEIGHT ADJUST lever of the projector after its height has been finely adjusted.
Correcting Trapezoidal Distortion Adjustment buttons (P/R/O/Q) When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. Note • The Keystone Correction can be adjusted up to an angle of approximately ±40 degrees and the screen can also be set up to an angle of approximately ±40 degrees (when the resize mode is set to “NORMAL” (see page 31)).
Image Projection (Continued) COMPUTER, DVI, S-VIDEO, VIDEO buttons Switching the Input Mode Select the appropriate input mode for the connected equipment. AV MUTE button Press COMPUTER, DVI, S-VIDEO or VIDEO on the remote control to select the input mode. VOL +/– (Volume) buttons • When you press INPUT on the projector or DVI on the remote control, the INPUT list appears. Press P/R to switch the INPUT mode.
Resize Mode This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose a desired image. Press RESIZE. • See page 44 for setting on menu screen.
Image Projection (Continued) VIDEO VIDEO/DTV Input signal Video/DTV Output screen image Image Type NORMAL AREA ZOOM V-STRETCH STRETCH *1 4:3 aspect ratio 480I, 480P, 576I, 576P, NTSC, PAL, SECAM *1 Squeeze *1 Letter box *1 720P, 1035I, 1080I, 1080P 16:9 aspect ratio *1 16:9 aspect ratio — *2 *1 16:9 aspect ratio 540P *1 16:9 aspect ratio (4:3 aspect ratio in 16:9) : Cutout area on which images cannot be projected : Area on which the image is not included in the original signals *1 The
Operating with the Remote Control BREAK TIMER button FREEZE button MAGNIFY buttons Displaying the Pointer 1 Press POINTER and press P/R/ O/Q on the remote control to move the pointer. 2 Press POINTER again. POINTER button SPOT button Adjustment buttons (P/R/O/Q) PICTURE MODE button ECO+QUIET button AUTO SYNC button Displaying and Setting the Break Timer 1 Using the Spot Function 1 Press SPOT and press P/R/O/Q on the remote control to move the spot area. 2 Press SPOT again.
Operating with the Remote Control (Continued) Auto Sync (Auto Sync Adjustment) Displaying an Enlar ged Portion of an Image Auto Sync function works when detecting input signal after the projector turns on. Press AUTO SYNC to manually adjust with Auto Sync function. Graphs, tables and other portions of projected images can be enlarged. This is helpful when providing more detailed explanations. 1 Note Press control. MAGNIFY on the remote • Enlarges the image.
Using the Remote Control as the Wireless Computer Mouse When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse. If the computer is placed too far away from the projector to be connected via the USB cable, the remote receiver (optional, AN-MR2) makes it possible to operate the projector with the remote control. For details, see the operation manual of the receiver.
Menu Items The following shows the items that can be set in the projector. Main menu “Picture” menu Picture Page 41 PAGE 1 Picture SCR Picture Mode Contrast Bright Color Tint Sharp Red Blue PRJ Net. Sub menu Standard Presentation Movie Game sRGB*1 Picture Mode Page 41 Help Standard 0 0 0 0 0 0 0 Contrast -30 +30 Bright -30 +30 Color -30 +30 *2 Tint -30 +30 *2 Sharp -30 +30 *2 Red -30 +30 Blue -30 +30 Page 42 SEL./ADJ.
“Screen adjustment (SCR-ADJ)” menu Pict. SCR-ADJ PRJ Resize Image Shift Keystone Auto Keystone OSD Display Background Setup Guide PRJ Mode Language Net. Help Main menu SCR - ADJ Stretch Page 44 0 0 Sub menu Resize Page 44 Image Shift On On Logo On Front English -40 +40 Page 44 Keystone -80 +80 Page 44 Normal Full Dot By Dot Area Zoom V-Stretch Stretch Normal Area Zoom V-Stretch Stretch VIDEO/ S-VIDEO COMPUTER/ DTV Auto Keystone [On/Off] Page 44 OSD Display [On/Off] Page 45 SEL./ADJ.
Menu Items (Continued) Main menu “Network” menu Pict. SCR PRJ Network Network Password Disable DHCP Client Off Help Page 49 Password [Enable/Disable] Page 49 DHCP Client [On/Off] Page 50 TCP/IP Page 50 TCP/IP MAC Address MAC Address X X : X X : X X : X X : X X : X X Projector Page 50 Projector XX-XXXX Page 50 SEL./ADJ. ENTER END The items you can set with the “Help” menu “Help” menu Pict. SCR PRJ Net.
Using the Menu Screen ENTER button Adjustment buttons (P/R/O/Q) MENU/HELP button ENTER button Adjustment buttons (P/R/O/Q) RETURN button • Press RETURN to return to the previous screen when the menu is displayed. MENU/HELP button Menu Selections (Adjustments) Example: Adjusting “Bright”. • This operation can also be performed by using the buttons on the projector. 1 Press MENU/HELP. 2 Press Q or O and select “Picture” to adjust. • The “Picture” menu screen for the selected input mode is displayed.
Using the Menu Screen (Continued) 3 Press P or R and select “Bright” to adjust. • The selected item is highlighted. Picture SCR PRJ Picture Mode Contrast Bright Red Blue CLR Temp BrilliantColor TM C.M.S. Setting C.M.S. Lamp Setting Reset SEL./ADJ. Net. Help Standard 0 0 0 0 0 1 On Bright Single ADJ END Items to be adjusted Pict. To adjust the projected image while watching it Press ENTER. • The selected item (e.g. “Bright”) is displayed by itself at the bottom of the screen.
Picture Adjustment (“Picture” Menu) Menu operation n Page 39 Q PAGE1 Q PAGE2 Picture 1 2 SCR Picture Mode Contrast Bright Color Tint Sharp Red Blue SEL./ADJ. PRJ Net. Help Picture Standard 0 0 0 0 0 0 0 ENTER SCR PRJ Picture Mode 3 2 4 5 6 END Net. Help Standard CLR Temp BrilliantColor TM C.M.S. Setting C.M.S. Progressive Lamp Setting Reset SEL./ADJ.
Picture Adjustment (“Picture” Menu) (Continued) Menu operation n Page 39 2 Adjusting the Image Adjustment items Contrast Bright Color*1 Tint*1 Sharp*1 2 Red* Blue*2 BrilliantColor™*2 *3 O button Q button For less contrast. For less brightness. For less color intensity. For making skin tones purplish. For less sharpness. For weaker red. For weaker blue. For making the effect weaker. For more contrast. For more brightness. For more color intensity. For making skin tones greenish. For more sharpness.
Menu operation n Page 39 5 Progressive Selectable items Description Useful to display fast-moving images 2D Progressive such as sports. Useful to display relatively slow3D Progressive moving images such as drama and documentary more clearly. Film Mode Reproduces the image of film source* clearly. Displays the optimized image of film transformed with three-two pull down (NTSC and PAL60Hz) or two-two pull down (PAL50Hz and SECAM) enhancement to progressive mode images.
Adjusting the Projected Image (“SCR - ADJ” Menu) Menu operation n Page 39 Pict. 1 2 3 4 5 6 7 8 SCR-ADJ Resize Image Shift Keystone Auto Keystone OSD Display Background Setup Guide PRJ Mode Language SEL./ADJ. 1 Setting the Resize Mode Note • For details of the Resize mode, see pages 31and 32. • You can also press RESIZE on the remote control to set the resize mode. (See page 31.) PRJ Net.
Menu operation n Page 39 4 Setting the On-screen Display Selectable items Description On All on-screen displays are displayed. Off INPUT/VOLUME/AV MUTE/FREEZE/ AUTO SYNC/RESIZE/PICTURE MODE/ ECO+QUIET/MAGNIFY/ “An invalid button has been pressed.” are not displayed.
Adjusting the Projector Function (“PRJ - ADJ” Menu) Menu operation n Page 39 Pict. 1 2 3 4 5 6 7 8 9 0 SCR Auto Sync Auto Power Off Auto Restart STANDBY Mode System Sound Speaker Audio Input RS-232C Fan Mode System Lock Lamp Timer(Life) SEL./ADJ. PRJ-ADJ 0 h Net. Help On On On Standard On On Audio 1 9600bps Normal Disable 0 min 100% ENTER Description Auto Sync adjustment will occur when the projector is turned on or when the input signals are switched, when connected to a computer.
Menu operation n Page 39 7 Audio Input 6 Monitor Output This function allows you to select an appropriate combination of audio input terminals for each input mode. Selectable items Description Audio 1 The AUDIO 1 input terminal is used as an audio input terminal. Audio 2 The AUDIO 2 input terminal is used as an audio input terminal. a Setting/Changing the keycode 1 Select “System Lock”, then press ENTER or Q. 2 Select “Next”, then press ENTER.
Adjusting the Projector Function (“PRJ - ADJ” Menu) (Continued) 5 Enter the same keycode in “Reconfirm”. Locking the Operation Buttons on the Projector Note To cancel the keycode that you have already set • Press R on the projector for four times in steps 4 and 5 above. When the System Lock is set • When System Lock is set, the keycode input screen appears after the power is turned on. When it appears, enter the right keycode to start projection.
Setting up the Projector Network Environment (“Network” menu) Menu operation n Page 39 Pict. SCR PRJ Network 1 Password Disable 2 DHCP Client Off 3 TCP/IP Help MAC Address X X : X X : X X : X X : X X : X X 4 Projector XX-XXXX SEL./ADJ. ENTER END 1 Setting a Password If you do not want others to change the setting for the “Network” menu, set a password. a Setting a Password 1 Select “Password”, then press ENTER or Q. • The screen for entering the password appears.
Setting up the Projector Network Environment (“Network” menu) (Continued) Menu operation n Page 39 2 DHCP Client Setting Connect the LAN cable before turning the projector on. If not, the DHCP Client function does not work. Selectable items Selectable items Factory default setting: 192.168.150.002 Enter an IP address appropriate for the network. Subnet Mask Factory default setting: 255.255.255.000 Set the subnet mask to the same as that of the computer and equipment on the network.
Troubleshooting with the “Help” Menu This function advises you to solve the problems during usage. Utilizing the “Help” Menu Functions ENTER button Adjustment buttons (P/R/O/Q) Example: When image flickering appears Operation to solve image flickering when projecting the computer RGB signal. 1 Press MENU/HELP. 2 Press O or Q to select “Help”, then press ENTER. 3 Press P or R to select “Vertical stripes or flickering image appears” on Help menu, then press ENTER. Pict. SCR PRJ Net.
Maintenance Cleaning the projector ■ Ensure that you have unplugged the power cord before cleaning the projector. ■ The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet. ■ Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods. The effects of some of the agents in the plastic may cause damage to the quality or finish of the projector.
Cleaning and Replacing the Dust Filters Cleaning the Dust Filters Info • The dust filters should be cleaned every 100 hours of use. Clean the filters more often when the projector is used in a dusty or smoky location. 1 Press STANDBY/ON on the projector to put the projector into standby mode. STANDBY/ON button • Wait until the cooling fan stops. • Disconnect the power cord and unplug the power cord from the AC socket. AC socket 2 Remove the filter holders.
Cleaning and Replacing the Dust Filters (Continued) 4 Replace the filter holders. • Align the tabs on the filter holders while replacing them, and then press down on the tabs to lock them in place. Note • Be sure the filter holders are securely installed. The power will not turn on unless it is correctly installed. Replacing the Dust Filters Info • If the filters become too dirty to clean effectively, purchase new ones (PFILDA025WJZZ) from your nearest Sharp Authorized Projector Dealer or Service Center.
Maintenance Indicators ■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector. ■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter standby mode. After the projector has entered standby mode, follow the procedures given below.
Maintenance Indicators (Continued) Maintenance indicator Temperature warning indicator Lamp indicator Power indicator Normal Abnormal Off Red on (Standby) Red on Problem The internal temperature is abnormally high. Cause • Blocked air intake • Relocate the projector to an area with proper ventilation. (See page 8.
Regarding the Lamp Lamp ■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (See page 48.) ■ Purchase a replacement lamp of type AN-F310LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center. IMPORTANT NOTE TO U.S.
Regarding the Lamp (Continued) Removing and Installing the Lamp Unit Warning! • Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury. Lamp unit AN-F310LP Optional accessory Info • Make sure that you remove the lamp unit by the handle. Do not touch the glass surface of the lamp unit or the inside of the projector.
4 Remove the lamp unit. 5 Insert the new lamp unit. 6 Handle • Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it. • Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws. Securing screws Replace the lamp unit cover. • Align the tab on the lamp unit cover (1) and place it while pressing the tab (2) to close it.
Storing the Projector How to Use the Storage Case When storing the projector, attach the lens cap to the lens, and place it in the supplied storage case. 1 Open the cover of the storage case. 2 Place the projector into the storage case. Info • Ensure the projector has cooled down sufficiently before placing it in the case. • When you place the projector into the storage case, make sure that the cooling fan has stopped. • Ensure the lens cap is attached to the lens for protection.
Computer Compatibility Chart Computer • Multiple signal support Pixel Clock: 12-170 MHz Horizontal Frequency: 15-110 kHz, Sync signal: Compatible with TTL level Vertical Frequency: 45-85 Hz, • Compatible with sync on green signal The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.
Troubleshooting Problem Check Projector power cord is not plugged into the wall outlet. Power to the external connected devices is off. The selected input mode is wrong. Cables are incorrectly connected to the projector. Remote control battery has run out. External output has not been set when connecting notebook computer. The lamp unit cover is not installed correctly.
Problem An unusual sound is occasionally heard from the cabinet. Maintenance indicator on the projector illuminates or blinks in red. The projector cannot be turned on or put into the standby mode using STANDBY/ON on the projector. Picture is green on COMPUTER (Component)/ DVI (Component). Picture is pink (no green) on COMPUTER (RGB)/ DVI (RGB). Picture is too bright and whitish. The cooling fan becomes noisy. The lamp does not light up even after the projector turns on.
For SHARP Assistance If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 62 and 63. If this operation manual does not answer your question, please contact the SHARP Service departments listed below. U.S.A. Sharp Electronics Corporation 1-888-GO-SHARP (1-888-467-4277) lcdsupport@sharpsec.com http://www.sharpusa.com Canada Sharp Electronics of Canada Ltd. (905) 568-7140 http://www.sharp.
Specifications Model Display devices Resolution Lens F number Zoom Focus DVI-I (Compatible with HDCP) Input terminals Computer/Component (mini D-sub 15 pin) S-Video (mini DIN 4 pin) Video (RCA) Audio (ø3.5 mm stereo minijack) Audio (RCA) Output terminals Computer/Component (mini D-sub 15 pin) Audio (ø3.
Dimensions 23 64 / (9) 11 1/32 (280) 13 64 / (5) Units: inches (mm) 7 16 / (11) 4 19/64 (109) 2 7/8 (73) 1 55/64 (47) ø9 7/64 (69.2) 3 5/32 (80) 3 1/16 (77.5) 7 16 / (11) 1 7/8 (47.5) 4 7/64 (104) 12 13/32 (315) 1 11/32 (33.8) 2 61/64 (75) 66 1 53/64 (46.2) 2 19/32 (65.
Index Accessories ............................................................. AC socket ................................................................ Adjustment buttons ................................................. AREA ZOOM ........................................................... Aspect ratio ............................................................. Audio Input .............................................................. AUDIO 1, 2 terminal ................................................
