Service manual

QT-CD210/C
– 2 –
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
BEFORE RETURNING THE AUDIO PRODUCT
(Fire & Shock Hazard)
Before returning the audio product to the user, perform the
following safety checks.
1. Inspect all lead dress to make certain that leads are not
pinched or that hardware is not lodged between the chassis
and other metal parts in the audio product.
2. Inspect all protective devices such as insulating materials,
cabinet, terminal board, adjustment and compartment
covers or shields, mechanical insulators etc.
3. To be sure that no shock hazard exists, check for leakage
current in the following manner.
* Plug the AC line cord directly into a 120 volt AC outlet.
* Using two clip leads, connect a 1.5k ohm, 10 watt resistor
paralleled by a 0.15µF capacitor in series with all exposed
metal cabinet parts and a known earth ground, such as
conduit or electrical ground connected to earth ground.
* Use a VTVM or VOM with 1000 ohm per volt, or higher,
sensitivity to measure the AC voltage drop across the
resistor (See diagram).
* Connect the resistor connection to all exposed metal parts
having a return path to the chassis (antenna, metal cabinet,
screw heads, knobs and control shafts, escutcheon, etc.)
and measure the AC voltage drop across the resistor.
IMPORTANT SERVICE NOTES (FOR QT-CD210 ONLY)
All check must be repeated with the AC line cord plug connection
reversed.
Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp.
AC.) or more is excessive and indicates a potential shock
hazard which must be corrected before returning the audio
product to the owner.
SPECIFICATIONS
Specifications for this model are subject to change without
prior notice.
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
TEST PROBE
0.15 µ F
1.5k ohms
10W
VTVM
AC SCALE
● General
Power source: AC 120 V, 60 Hz
DC 9 V [ "D" size (UM/SUM-1, R20
or HP-2) battery × 6]
Power
consumption: 12 W
Output power: FTC; 2.0 W min. RMS per channel
into 4 ohms from 150 Hz to 20
kHz, with no more than 10 % total
harmonic distortion.
RMS; 2.3 W/CH
(DC operation, 10 % T.H.D.)
Speakers: 4" (10 cm) full-range speaker x 2
Dimensions: Width; 15-3/4" (400 mm)
Height; 6-1/4" (158 mm)
Depth; 8-3/8" (212 mm)
Weight: 6.0 lbs. (2.7 kg) without batteries
● Compact disc player
Type: Compact disc
Signal
readout:
Non-contact, 3-beam semi-
conductor laser pickup
Audio
channels: 2
Filter: 8-times oversampling digital filter
D/A
converter: 1-bit D/A converter
Wow and
flutter:
Unmeasurable
(less than 0.001% W. peak)
● Radio
Frequency
range:
FM; 87.6 - 108 MHz
AM; 530 - 1,720 kHz
● Tape recorder
Frequency
response: 50 - 14,000 Hz (Normal tape)
Signal/noise
ratio: 50 dB
Wow and
flutter: 0.25 % (WRMS)
Motor: DC 9 V electric governor
Bias system: AC bias
Erase
system: Magnet erase
Output power: RMS; 2.3 W/CH
(DC operation, 10 % T.H.D.)
Speakers: 10 cm (4") full-range speaker x 2
Dimensions: Width; 400 mm (15-3/4")
Height; 158 mm (6-1/4")
Depth; 212 mm (8-3/8")
Weight: 2.7 kg (6.0 lbs.) without batteries
(For QT-CD210)
(For QT-CD210C)