Beam 200W Moving Head Light USER MANUAL
200W Beam Light Manual 1．Safety Information……………………………………………3 2．Installation and Startup……………………………………5 3．Menu settings …………………………………………………9 4．Technical Information………………………………………10 5．Channel function………………………………………………11 Unpacking Inspection 1、Unpacking First of all, thank you for choosing a product from the factory, please read this manual completely and carefully and keep it for reference.
the right to update the relevant parts of the specification at any time without prior notice. Pictures of this manual and the actual product differences, original structure, is subject to the physical.
To drag the power cord to pull the plug . ◆ This level of protection of the equipment for Class I , so please connect the yellow / green wire grounded . ◆ line connection , maintenance and service must be carried out by specialized technical staff . ◆ Do not connect the device in the dimming device . ◆ Do not use in very short time intervals to continuously turn the device on or off, otherwise it will shorten the bulb Life. ◆ the first use of the equipment, there may be some smoke or smell .
◆ maximum ambient temperature This device uses a maximum ambient temperature does not exceed 40 ℃ (104 ℉). ◆ Protection class IP20 This equipment can prevent the infiltration of a diameter of more than 12mm of solid , but not water proof , water droplets splashing into ◆ anti-lightning The level of protection for this equipment for Class I , so please connect the yellow / green wire grounded .
Installation and Startup Figure 1: X -axis its lock and release mechanisms, every 90 ° locking and releasing 5
Figure 2: Y -axis its lock and release mechanisms, every 45 ° locking and releasing 6
Figure 3 : The lamps can be installed in the rubber feet , the floor trusses , ceiling or wall .
Figure 5: Connecting to power Figure 6 : Connecting to the control signal line ( DMX ) Note: Please use meets specifications shielded 2-pole twisted pair signal lines, characteristic impedance of 120 ohms , do not use the microphone Cable or other specified uses signal line.
XLR 3-pin male and female connector Canon. Important Note: 2-pole line can not be with each other or in contact with the metal shell of the connector. Shield to pin 1 must sleeve wrapped. Menu settings Using the menu: 1. Boot display the main screen, press the black knob center once, the main menu appears on the display , enter the main menu setting items , the main Menu set of nine, are: 1. Exit ; 2.dmx address ; 3 . Parameter settings; 4 options; 5 display settings; Manual control; 7.
(2) ON vii effect round the shortest distance (1) NO (2) YES viii. allow DMX reset (1) NO (2) YES e) Display Settings i. return ii display language 1. English 2 Chinese f) manual control i. return ii. CH1 (0-255) ... CH32 (0-255) g) test run i. return ii. voice self-propelled iii. h) to restore the factory model i. return ii. confirmation i ) lamp reset i. return ii.
governor (0.5-14 seconds) The level scan: 540 degrees, Resolution 8Bit/16Bit , automatic correction The scan vertical: 250 degrees, Resolution 8Bit/16Bit, auto-correction beam angle : parallel beam angle : 0 - 3.
CH5: X/Y scan speed 0-255 high - slow CH6: Dimmer 0-255 OFF - ON CH7: Strobe 0 1--50 51--240 241--255 OFF ON Strobe slowly -- highly OFF CH8: Fog Filter 0-255 None - Fog CH9: Color 0-8 8-15 16-23 24-31 32-39 40-47 48-55 56-63 64-71 72-79 80-87 88-95 96-103 104-111 112-127 128-191 192-255 White Color 1 Color 2 Color 3 Color 4 Color 5 Color 6 Color 7 Color 8 Color 9 Color 10 Color 11 Color 12 Color 13 Color 14 Rainbow effect positive rotation highly -- slowly Rainbow effect reversal rotation highly --
28-34 35-41 42-48 49-55 56-62 63-69 70-76 77-83 84-90 91-97 98-104 105-111 112-118 119-127 128-191 192-255 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Gobo 8 Gobo 9 Gobo 10 Gobo 11 Gobo 12 Gobo 13 Gobo 14 Gobo 15 Gobo 16 Gobo 17 Rainbow effect positive rotation highly -- slowly Rainbow effect reversal rotation highly -- slowly CH12: Gobo Shaking 0-255 0--400° CH13: Prism 0-31 32-255 None Prism Prism CH14: Prism Rotation 0-127 Angle 128-191 positive rotation highly -- slowly 192-255 reversal rotation highly -- slowly CH
