LM10V332 Color STN LCD Module (Model Number: LM10V332) Specifications Spec No.: LC99213A Dated: May 31.
NOTICE This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party.
RECORDS OF REVISION DATE JUL.12.1999 REF.PAGE PARAGRAPH DRAWING No. P5,P6 REVISED SUMMARY NO. １ P5 /Table5 １ P10 /Table7 １ P16 /Fig7 １ P21 /Fig11 １ P25 １ Ambient temperature Supply current, Power comsumption, Rush current Data set up time VDD on/off cycle, Regulation “d”,”g”,”h” Applicable inspection standard DOC.FIRST ISSUE FEB.17.
SPEC No. MODEL No. LC99213A Contents LM10V332 Page 1.Application 2 2.Construction and Outline 2 3.Mechanical Specifications 3 4.Absolute Maximum Ratings 3 4-1.Electrical absolute maximum ratings 3 4-2.Enviroment Conditions 4 5.Electrical Specifications 5 5-1.Electrical characteristics 5 5-2.Interface signals 6 6.Module Driving Method 12 6-1.Circuit configuration 12 6-2.Display face configuration 12 6-3.Input data and control signal 12 7.Optical Characteristics 14 8.
SPEC No. LC99213A PAGE MODEL No. LM10V332 2 1. Application This data sheet is to introduce the specification of LM10V332, Passive Matrix type Color LCD module. 2. Construction and Outline Construction: 640×480 dots color display module consisting of an LCD panel, PWB(printed wiring board) with electric components mounted onto, TCP(tape carrier package) to connect the LCD panel and PWB electrically, and plastic chassis with CCFT back light and bezel to fix them mechanically.
SPEC No. PAGE MODEL No. LC99213A LM10V332 3. Mechanical Specification Table1 Parameter Outline dimensions Specifications Unit 264±0.5(W)×193.6±0.5(H)×8.5MAX(D) Mm Bezel opening area 215.2±0.3(W)×162.4±0.3(H) mm Display format 640(W)×480(H) full dots mm Dot size 0.09×RGB(W)×0.31(H) － Dot spacing 0.02 mm Normally black *2 － Approx. 450 g *1 Base color Weight *1 Due to the characteristics of the LC material, the colors vary with environmental temperature.
SPEC No. PAGE MODEL No. LC99213A LM10V332 4 4-2.Environment Conditions Table 3 Tstg Item Ambient temperature Topr MIN. MAX. MIN. -25 ℃ +60 ℃ 0 ℃ Remark MAX. １ +50 ℃ +40℃ Note 4) Humidity Note 1) Note 1) No condensation Vibration Note 2) Note 2) 3 directions(X/Y/Z) Shock Note 3) Note 3) 6 directions(±X±Y±Z) Note 1) Ta≦40 ℃ Ta＞40 ℃ 95 % RH Max. Absolute humidity shall be less than Ta=40 ℃/95 % RH. Note 2) Table 4 Frequency 10 Hz～57 Hz 57 Hz～500 Hz Vibration level - 9.
SPEC No. PAGE MODEL No. LC99213A LM10V332 5 5.Electrical Specifications 5-1. Electrical charasteristics Table 5 Parameter Symbol Supply voltage (Logic) VDD-VSS Ta=25 ℃ Conditions １ VDD= 5.0 V±10 % Min. Typ. Max. Unit 4.5 5.0 5.5 V 0.8 1.95 2.8 V 0.8VDD － VDD V 0 － 210 90 １ 1050 450 0.2VDD １ 320 135 １ 1600 680 １ 2A×2 1A×2 １ 1A×10 0.
SPEC No. LC99213A PAGE MODEL No. LM10V332 5-2.Interface signals LCD Pin No.
SPEC No. PAGE MODEL No. LC99213A LM10V332 CCFT Pin No Symbol Description Level 1 HV High voltage line (from Inverter) - 2 NC NC - 3 GND Ground line (from Inverter) - LCD Used connector : DF9B-31P-1V(HIROSE) Mating connector : DF9B-31S-1V(HIROSE) CCFT Used connector : BHR-03VS-1(JST) Mating connector : SM02(8.0)B-BHS(JST) Except above connector shall be out of guaranty.
SPEC No. LC99213A (1,1) (1,2) PAGE MODEL No.
SPEC No. PAGE MODEL No.
SPEC No. LC99213A Table 7 Item PAGE MODEL No. LM10V332 Interface timing ratings Symbol Rating MIN. TYP. MAX. tFRM 8.33 YD signal “H” level set up time tHYS 100 ns “H” level hold time tHYH 100 ns “L” level set up time tLYS 100 ns “L” level hold time tLYH 40 ns tWLPH 200 ns tCK 80 ns “H” level clock width tWCKH 30 ns “L” level clock width tWCKL 30 5 15 ns XCK signal clock cycle 16.
SPEC No. PAGE MODEL No. LC99213A LM10V332 t FRM t HYH t HYS t t LYS LYH YD t WLPH LP LP ｔ ＣＫ tr t LS XCK tf tW C K H tW C K L t LH t DH t DS D U 0～ 7 D L 0～ 7 V IH = 0 .8 V D D V IL = 0 .2 V D D F ig .
SPEC No. MODEL No. LC99213A PAGE LM10V332 12 6. Module Driving Method 6-1. Circuit configuration Fig.9 shows the block diagram of the module’s circuitry. 6-2. Display face configuration The display consists of 640×3(R,G,B)×480 dots as shown in Fig. 1. The interface is single panel with double drive to be driven at 1/240(1/244) duty ratio. (1/240:an odd number frame, 1/244:an even number frame) 6-3.
SPEC No. MODEL No. LC99213A PAGE LM10V332 13 Because of the characteristics of CMOS driver LSI, the power consumption of the display module goes up with the clock frequency of XCK. To minimize data transfer speed of XCK clock the LSI has the system of transferring 8 bit parallel data through the 8 lines of shift registers. Thanks to this system the power consumption of the display module is minimized. In this circuit configuration, 8 bit display data shall input to data input pins of DU0-7 and DL0-7.
SPEC No. PAGE MODEL No. LC99213A LM10V332 14 7. Optical Characteristics Following spec are based upon the electrical measuring conditions, on which the contrast of perpendicular direction(θx = θy = 0°) will be MAX.. Ta=25℃,VDD=5.0V,VCON-VSS=Vmax Table 8 Parameter Symbol Condition θx Viewing angle range Co>5.0 θy Contrast ratio MIN. TYP. MAX. Unit θy = 0 ° -30 － 30 deg. θx = 0 ° -15 － 25 deg.
SPEC No. PAGE MODEL No. LC99213A LM10V332 +θy 15 TOPCON BM-7 +θy -θx -θx normal Measuring Field: 2 ﾟ +θx -θy Measuring Spot Size : φ10 mm θx : Angle from “normal” to viewing surface rotated about the horizontal axis. θy : Angle from “normal” to viewing surface rotated about the vertical axis. Fig.5 Optical Characteristics Test Method Ⅰ Comax. Vmax. Fig.
SPEC No. PAGE MODEL No. LC99213A LM10V332 16 (Response Measurement) Ta = 25 ℃ In dark room θy(+) １ 85mm 350mm Computer LCD Control θx(-) circuit LCD Module A/D θx(+) Converter normal θy(-) θx=θy= 0° １ TOPCON BM7 + quartz fiber (Measuring spot size :φ10 mm, Measuring Field : 2°) Fig.
SPEC No. LC99213A PAGE MODEL No. LM10V332 17 [Drive waveform] Driving voltage 1/244 Duty Ratio Non-select waveform Select waveform Non-select waveform 10 % 90 % 100 % Photo detector output [Responce waveform] τr τd Fig.
SPEC No. LC99213A Resister DU0-DU7 DL0-DL7 XCK LP LM10V332 Chip inductor Buffer I.C YD PAGE MODEL No. DISP SEG Drivers (Upper) M general circuit (1,1)(1,2) (2,1)(2,2) COM Drivers Sequence control circuit DISP (1,640) (2,640) ＲＧＢ (240,1) (241,1) (240,640) (241,640) 640 X RGB X480 DOTS LCD Bias generator & Protection circuit (480,1) (480,640) SEG Drivers (Lower) V SS V DD DC/DC Converter Vcon Tempareture Compensation Circuit CCFT Inverter Fig.
SPEC No. PAGE MODEL No. LC99213A LM10V332 19 8.Characteristics of Backlight The ratings are given on condition that the following conditions are satisfied. 1) Rating(Note) Parameter MIN. TYP. MAX. Unit Brightness 120 160 － cd/m2 2) Measurement circuit : CXA-M10L(TDK) (at IL = 5.5 mArms) 3) Measurement equipment : BM-7 (TOPCON Corporation) 4) Measurement conditions 4-1. Measurement circuit voltage : DC = 10.6 V, at primary side 4-2.
SPEC No. PAGE MODEL No. LC99213A LM10V332 20 5-2) Operating life The operating life time is 25 000 hours or more at 5.5 mA , at 25℃. (Operating life with CXA-M10L or equivalent.) The inverter should meet the following conditions to keep the specified life time of used lamp; Since, symmetric waveform without spike in positive and negative Output frequency range : 30 kHz-70 kHz Make sure the operating conditions by executing the burn-in enough time.
SPEC No. PAGE MODEL No. LC99213A LM10V332 21 9. Supply voltage sequence condition １ 500 1500ms MIN. (NOTE 1) a (NOTE 2) e VDD YD Interface timing active operation LP XCK c (NOTE 3) １ h f DATA DISP b １ １ 4.5 V 3V １ 3.0V 3.5 V １ 2.0V 2.0V 3V 1.0V VDD VSS d g Fig.11 Supply voltage sequence condition POWER ON Symbol POWER OFF Allowable value Symbol a 0 ms MIN. 1 s MAX. ｅ b － 100 ns MAX. ｆ c 50 ms MIN. - d - 10 ms MAX. 0 ms MIN. 1 s MAX. 0 ms MIN. 10 ms MIN.
SPEC No. MODEL No. LC99213A LM10V332 PAGE 22 10. Cautions 1) Industrial(Mechanical) design of the product in which this LCD module will be incorporated must be made so that the viewing angle characteristics of the LCD may be optimized. This module’s viewing angle is illustrated in Fig.12. θy MIN. < viewing angle <θy MAX. (For the specific values ofθy MIN., andθy MAX., refer to the table8) Please consider the optimum viewing conditions according to the purpose when installing the module.
SPEC No. LC99213A MODEL No. PAGE LM10V332 23 1. Operator Electrostatic shielding clothes shall be had because it is feared that the static electricity is electrified to human body in case that operator have a insulating garment. 2. Equipment There is a possibility that the static electricity is charged to equipment which have a function of peeling or mechanism of friction(EX: Conveyer, soldering iron, working table), so the countermeasure (electrostatic earth:1×108Ω) should be made. 3.
SPEC No. MODEL No. LC99213A PAGE LM10V332 24 13) Procedure insert mating connector When the mating connector is inserted, it should be parallel to the used connector of LCD module and it should be inserted on horizontal firm base. When the mating connector is attempted to be fixed to LCD connector, it should be inserted properly in order not to create a gap as shown following diagram 2). Please insert the connector as both edge is placed to the connect position of LCD connector.
SPEC No. MODEL No. LC99213A 14) This specification PAGE LM10V332 25 describes display quality in case of no gray scale. Since display quality can be affected by gray scale methods, display quality shall be carefully evaluated for the usability of LCD module in case gray scale is displayed on the LCD module. 15) The module should be driven according to the specified ratings to avoid permanent damage.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP’s product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED.
