Monogram. Use & Care Guide and Installation Instructions for ZDIB50 ZDIW50 Automatic Icemaker Monogram.":" Automatic h:emaker General Electric Company Louisville, KY40225 Pub. No. 49-6857 Parl No.
Introduction Your new Monogram icemaker makes an eloquent statement of style, convenience and kitchen planning flexibility. Whether you chose it for its purity of design, practical features or assiduous attention to detail--or for all of these reasons--you'll find that your Monogram icemaker's superior blend of form and function will delight you for years to come. The Monogram icemaker was designed to provide the flexibility to blend in with your kitchen cabinetry.
HELP US HELP YOU... Read this guide carefully. Write It is intended to help you operate and maintain your new icemaker properly. You'll see them on a plate on the left side of the ice bin. These numbers are also on the Consumer Product Ownership Registration Card that came with your icemaker. Keep it handy for answers to your questions. If you don't understand something more help, call: GE Answer Center _"_ 800.626.2000 24 hours a day, 7 days a week or need If you received icemaker...
IMPORTANT SAFETY INSTRUCTIONS Read All Instructions Before Using This Appliance. _ ARNING--To reduce risk using of fire, electrical shock, or injurythewhen your icemaker, follow basic precautions including the following: • Never allow children to operate, play with, or crawl inside the icemaker. • Never clean icemaker parts with flammable fluids.
OPERATING How the Icemaker YOUR ICEMAKER Works 1. Water is constantly circulated over a freezing plate. As the water freezes into ice, the minerals in the water are reiected. This produces a sheet of ice with a low mineral content. NOTE: The icemaker is designed to make clear ice from the maiority of water sources on a daily basis. If your results are unsatisfactory, water may need to be filtered or treated. See Filtering and Treating Water in the Care and Cleaning section. 2.
OPERATING YOUR ICEMAKER (continued) Setting the Controls 1. Select ice thickness. The icemaker has been preset to produce ice approximately 1/2" (13 mm) thick, while operating in a room temperature of 70°F. (21°C.). Operation in different room temperatures may require readjusting the control toward either the "THICK" or "TH1N" setting. ON I NORMAL THIN THICK OFF -_- Best operation will be obtained with ice 1/2" (13 mm) to 5/8" (16 mm) thick.
CARE AND CLEANING Periodically inspect and clean the icemaker to keep it operating at peak efficiency and to prevent premature failure of system components. Both the icemaking system and the air-cooled condenser need to be cleaned regularly. A dirty or clogged The minerals reiected from the circulating water during the freezing cycle will eventually form a hard scaly deposit in the water system which prevents a rapid release of the ice from the freezing plate.
CARE AND CLEANING (continued) Cleaning the Icemaker System A are WARNING: citric or phosphoric Most ice machine acid which cleaners can cause irritation even after dilution. In case of contact with eyes, flush eyes thoroughly with fresh water and contact a physician immediately. In case of contact with skin, rinse well with water. If swallowed, give large amounts of water and contact a physician immediately. Do not induce vomiting. KEEP OUT OF REACH OF CHILDREN. .
Cleaning the Inside Parts of the Icemaker WARNING: Water Distlributor • Do not operate the icemaker with the lower access panel or control panel removed. Electrical shock or personal injury could result. o Do not wash plastic parts in dishwasher. They cannot withstand temperatures above 145°E (63°C.). . . 3. Turn the Cycle Control Knob to "OFF" and disconnect the electrical power supply to the machine. Open the storage bin door and remove any ice that is in the bin. .
CARE AND CLEANING (continued) Filtering and Treating Water In most areas it will be beneficial to filter or treat the water being supplied to the icemaker. It can improve the reliability of the icemaker, reduce water system maintenance and produce the best quality of ice. The installation of a polyphosphate feeder will generally reduce scale build-up and the icemaker will require less frequent cleaning.
PREPARATION Unpacking the Icemaker 1. Lay the carton on rear face and break open the bottom flap. 2. Set the carton upright with all four flaps outward. . ° 3. Lift carton up and off icemaker. "2 Remove all tape and packaging material from the outside and inside of the cabinet. Remove the front grille; take out the screws securing the grille at the bottom and lift it free of the cabinet. Remove Interior Packing 6. Turn the fan by hand to make certain it moves freely.
PREPARATION (continued) Changing the Bin Door Panel You can easily change the color of the front panel on the storage bin door. Two colors are available: black and white. Handle To change the panel: Insert 1. Open the storage bin door. Remove the two screws on the top of the door which hold the handle. 2. Loosen the screws in both of the side trim pieces. 3. Remove the handle and the handle insert. 4. Carefully slide the panel out. You will find the reverse side is black.
Changing the Lower Access Panel control panel removed. Electrical shock 1. Remove the screw from the top of the lower access panel and the two screws in the bottom grille area. Pull forward at the bottom, then down to remove the panel. Grill Area Screws 2. Remove the two screws from the top panel trim and remove the top trim. / 3. Carefully slide the panel out. 4. Choose the color you want to show and carefully slide the panel back into the lower access panel.
DOOR AND ACCESS PANELS CUSTOM Custom Door and Access Panels--I/4" Thick Door Bin Lower Panel Cut panels to the same size as the production metal panel. t 11//4" Wood Panel Dimensions 11W_o" 17" Custom Door and Access Panels--3/4" Thick These door and access panels--both raised and flat design--should be constructed in the same manner as typical cabinet doors or drawers. Storage II, 17" 91 -f Storage Bin Door Panel 11//4" bin door panel: • Cut the panel 17" wide x 111/4"high.
Vacation and Moving "WARNING: Make sure the icemaker is disconnected from the main power supply before removing the lower access panel. Failure to do so could result in electric shock or personal injury. To shut down the icemaker: NORMAL 0 \ THIN - 1. Disconnect the electrical power supply to the icemaker and turn the Cycle Control Knob to "OFF." 2. Remove all ice from the storage I / - THICK OFF - ICE "_ CYCLE bin. 3. Shut off the water supply. 4.
FREE For STANDING INSTALLATION the Installer When this icemaker is installed free standing (not under a counter) we strongly recommend that the bottom rear comers of the icemaker be fastened to the floor to prevent accidental tipping. INSTALLATION IMPORTANT...Please For the Electrician--Electrical REQUIREMENTS Read Carefully Requirements A 115 Volt, 60 Hz, AC only, 15 Amp fused electrical supply is required (time delay fuse or circuit breaker is recommended).
3/4" -'_ Right end view 237/8" _ t1 Water inlet solenoid valve 1/4" O.D. water line. compression fitting at water valve \ \ _ / / ,,/_ _ ._'--------..... _L _" _, , _J 33/Z' /'/2" -i'-. ..... Figure l , r'_?" / 34I/2" 9" TF_ / '-_1 [_NJr d --11/4" Min. 1 y__ -- Hole for field supplied water line 41/2"t0 i 0o\ center line \ /, 2V2" -_'_" ["_/4- "_ 3/4" _ ,%,_- ., open drain L [. \k i _ 1,1.' ,, /' _ .2,T 4" tong 5/8" I.D.
DRAIN PUMP CHECKOPERATION • When the drain connection is below the level of the icemaker, a drain pump may be used to lift the water to an available drain. Use only an approved drain pump kit ZDK50 from your dealer. • Start the icemaker by turning the service switch to "ON" and opening the line water valve. • NOTE: Left is "OFF"--Middle is "ON"--Right is "CLEAN." In "CLEAN" position, only the pump operates. • Check the condenser fan to make sure it is revolving.
QUESTIONS? USE THIS PROBLEM SOLVER PROBLEM ICEMAKER NOT RIfN POSSIBLE DOES CAUSE • Cycle Control Knob must be in the "ON" position. • Check to see that the power • Have you checked cord is plugged your home's in. main fuses or circuit breaker box? • Room temperature must be above 55°F. (13°C.). Otherwise, the bin thermostat may sense the cold room temperature and shut off even though the bin is not full of ice. Also. the icemaker may not restart once it does shut off.
We'll Be There With the purchase of your new GE appliance, receive the assurance that if you ever need information or assistance from GE, we'll be there. All you have to do is call-toll-free! GEAnswerCenter® 800.626.2000 ® Whatever your question about any GE major appliance, GE Answer Center information setsTice is m_ailable to help. Your call-and your questionwill be answered promptly and courteously. And you can call any time. GE Answer Center ®sets_ice is open 24 hours a day, 7 days a week.
YOUR GEICEMAKER Staple sales slip or cancelled check here. Proof of original purchase date is needed to obtain service under warranty. WARRANTY WHAT IS COVERED FULL ONE-YEAR WARRANTY For one year from date of original purchase, we will provide, free of charge, parts and service labor in your home to repair or replace any part of the icemaker that fails because of a manufacturing defect.
NOTES 22
Monogram. Manual del usuario e instrucciones para la instalaci6n para ZDIB50 ZDIW50 M_tquina para hacer hielo Monogram.":" Mdquina Pub. General Electric Company Louisville, KY40225 Parl No. No.
Introducci6n Su nueva mfiquina para hacer hielo Monogram es una afirmacidn elocuente de estilo, comodidad y flexibilidad en la planeaci6n de su cocina. Ya sea que la elija por la pureza de su disefio, por las caracteristicas fisicas o por la constante atenci6n al detalleIO por todas estas razonesIencontrarfi que la conbinaci6n de forma y funci6n de su maquina para hacer hielo Monogram es superior y darfi una gran satisfacci6n durante los afios venideros.
AYUDENOS Lea cuidadosamente este folleto. A AYUDARLE... Anote el modelo y los nfimeros de serie. Es nuestra intencidn ayudarle a operar y mantener adecuadamente su nuevo mfiquina para hacer hielo. Los verfi en la placa del lado izquierdo almacenamiento. Mantenga este folleto a la mano para responder sus preguntas. Estos nfimeros se encuentran tambidn en la Tarjeta de registro de propiedad del producto del consumidor que se proporciona junto con su mfiquina para hacer hielo.
INSTRUCCIONES DE SEGURIDAD Lea todas las instrucciones antes de usar este electrodom stico. A ADVERTENCIA--Para reducir el riesgo de incendio, choque el6ctrico o lesiones cuando est_ usando su mfiquina para ......... nacer nlelO, slga precanclones oaslcas incluyendo las siguientes: • Nunca permita que los nifios operen, jueguen con la mfiquina o se metan al interior de la mfiquina. • Nunca limpie las partes de la mfiquina para hacer hielo con liquidos inflamables.
OPERACION DE SU MAQUINA PARA HACER HIELO C6mo funciona la mfiquina para hacer hielo 1. E1 agua circula constantemente sobre una placa de congelacidn. A medida que el agua se enfria para llegar a congelarse, los minerales que contiene el agua son expulsados. Esto produce una capa delgada de hielo con baio contenido de minerales. NOTA: La mfiquina para hacer hielo estfi disefiada para fabricar hielo transparente con la mayoria de las fuentes de suministro de agua todos los dias.
OPERACION DE SU MAQUINA PARA HACER HIELO (pase) Ajustando los controles 1. Elija el espesor de hielo que desee. La milquina para hacer hielo ha sido ajustada en la filbrica para producir hielo de aproximadamente 1/2" (13 mm) de espesor, siempre que estd operando a una temperamra ambiente de 70 °F. (21 °C.). ON I NORMAL THIN THICK La operacidn a una temperamra ambiente distinta puede requerir un reajuste del control ya sea hacia la posicidn "THICK" (grueso) o "THIN" (delgado).
CUIDADO Y LIMPIEZA Inspeccione y limpie periddicamente la mfiquina para hacer hielo de modo que siga funcionando a su mfixima eficiencia y para prevenir una falla premamra de los componentes del sistema. Tanto el sistema de fabricacidn de hielo como el condensador enfriado por aire necesitan ser limpiados de manera regular.
CUIDADO Y LIMPIEZA (pase) Limpieza del sistema de la mfiquina para hacer hielo . A DVERTENCIA: La mavoriase hacen de los a limpiadores para mfiquinas base de ficido citrico o fosf6rico y pueden causar irritaci6n incluso despu6s de ser diluidos. En el caso de contacto con los ojos, enjuague los ojos meticulosamente con agua y llame a un m6dico de inmediato. En caso de contacto con la piel, enjuague bien con agua. Si se ingiere, d61e a la persona grandes cantidades de agua y llame a un m6dico de inmediato.
Limpieza de los componentes interiores Distribuidor de agua si quit6 el panel inferior de acceso o el tablero de control. Puede sufrir un choque el_ctrico o lesiones en su persona. • No lave las partes plfisticas en la mfiquina lavavajillas. Las partes no resisten temperaturas superiores a 145 °E (63 0C.). Haga girar la perilla de Control de ciclo hasta la posicidn de "OFF" (apagado) y desconecte el suministro de corriente eldctrica que alimenta la mfiquina.
CUIDADO Y LIMPIEZA (pase) Filtrado y tratamiento del agua En la mayoria de las fireas seria beneficioso filtrar o tratar el agua que alimenta la mfiquina para hacer hielo. Esto puede mejorar la confiabilidad de la mfiquina, reducir el mantenimiento del sistema de agua y producir la mejor calidad de hielo. La instalacidn de un alimentador de polifosfato por lo general reducirfi la formacidn de acumulaciones de sales y la mfiquina para hacer hielo requerirfi de limpiezas menos frecuentes.
PREPARACION C6mo desempacar la mfiquina para hacer 1. Coloque la caia sobre la parte inferior tapas del fondo. y abra las hielo o 2. Coloque la caia derecha con las cuatro tapas abiertas hacia afuera. o 3. Levante la caia de cartdn hasta deiar al descubierto la mfiquina para hacer hielo. ° / Quite toda la cinta adhesiva y los materiales de empaque del exterior y del interior del gabinete.
PREPARACION (pase) C6mo cambiar el panel de la puerta del dep6sito Usted puede cambiar con facilidad el color del panel delantero de la puerta del depdsito de almacenamiento. Hay dos colores disponibles: negro y blanco. Manija Para cambiar el panel: de la manija 1. Abra la puerta del depdsito de almacenamiento. Quite los dos tomillos que se encuentran en la parte superior de la puerta y que sostienen la manija. 2. Afloje los tomillos guamiciones. en ambos lados de las 3.
C6mo cambiar el panel inferior de acceso ADVERTENCIA: No opere la mfiquina para hacer hielo si ha quitado el panel _l inferior de acceso o el panel de control. Puede sufrir un choque el6ctrico o lesiones personales. I A 1. Quite el tornillo de la parte superior del panel inferior de acceso y los dos tornillos que estfin en la parte de abaio del firea de la reiilla cortadora. Tire hacia el frente en la parte de abaio, entonces tire hacia abaio para quitar el panel. 2.
PUERTA Y PANELES DE ACCESO A LA MEDIDA Puerta y paneles de acceso a la medida de 1/4" de espesor Corte los paneles de metal. Dep6sito de Panel la puerta inferior Tt del mismo tamafio que el panel 11 VY' 11 WEJ' Dimensiones del panel de madera _1€/1!4" 17" 4' Ranure a una Puerta y paneles de acceso a la medida de 3/4" de espersor 17" La puerta y los paneles de acceso--ambos con disefios en relieve y plano--se deberfin armar de la misma manera que el gabinete, las puertas o los cajones tipicos.
Vacaciones y mudanzas A ADVERTENCIA: Asegfirese de que la mfiquina para hacer hielo est_ desconectada del suministro principal de corriente el_ctrica antes de quitar el panel inferior de acceso. Si no lo hace asi, corre el riesgo de recibir un choque el_ctrico o lesiones a su persona. Para apagar NORMAL 0 \ THIN - I 2. Retire todo el hielo del depdsito almacenamiento. 3. Cierre el suministro - THICK OFF - ICE la mfiquina para hacer hielo: 1.
INSTALACION Para INDEPENDIENTE el instalador Cuando se (no debajo posteriores para evitar instala esta mfiquina para hacer hielo de manera independiente de un mostrador) recomendamos fuertemente que las esquinas del fondo de la mfiquina para hacer hielo se suieten al suelo que se vuelque por casualidad. INSTRUCCIONES PARA LA INSTALACION IMPORTANTE...Leer Para el electricista--Requerimientos detenidamente el6ctricos Se requiere un suministro eldctrico de 115 voltios, 60 Hz y 15 amperes.
Vista del lado derecho Linea de compresi6n de 1/4" de diametro exterior que se conecta a la valvula de agua _ Vista posterior 4- 237/8" 3/4" -_ I <_ Valvula de solenoide de admisi6n de agua _ / _/'...... -_ £j 1 - "it, 33/4"_ Tubo de desagOe de 4" de largo y 5/8" de diametro interior--corre hacia el drenaje abierto 34W=" ,' I I ',¢ I -_- 7/_ ÷ 1_,-........ i_-_L. [ Figura 1 17%" --i,.- I -- _ - "_x i /' -- 11/4"Min. . 1_÷_.
NIVELACION BOMBA DE DESAGUE • Despu_s de colocar la mS.quina para hacer hielo en posicion, revise para cerciorarse que est_ nivelada de lado a lado y del frente hacia atras. • Cuando se instala la conexion de drenaje debajo de la m_.quina para hacer hielo, puede usarse una bomba de desagtie para llevar el agua hasta un drenaje disponible. Use solo un juego de bomba de desagtie aprobado ZDK50 de su distribuidor. • Una nivelacion precisa es esencial para una operacion adecuada. • La m_.
i,ALGUNA PREGUNTA? CONSULTE ESTAS SOLUCIONES PROBLEMA CAUSA POSIBLE LA MAQUINA PARA HACER HIELO NO FLrNCIONA • La perilla de control de ciclo debe estar en la posicion • Revise que el cable de corriente • LRevis6 la caia de fusibles de "ON" (encendido). estd conectado. o el interruptor de circuito? • La temperatura ambiente debe ser mayor que 55 °F. (13 °C.). De otro modo.
Estaremos Con Usted Con la compra de su nuevo aparato GE recibifft la seguridad de que si alguna vez necesita informaci6n o asesoria de GE, estaremos a su disposici6n. Todo lo que fiene que hacer es llamar-isin costo! En GE Answer Center se habla espafiol. GEAnswerCenter® 800.828.2000 Cualquiera que sea su pregunta sobre alguno de los grandes aparatos de GE, el smsTicio de informacidn de GE Answer (;enter sera dispuesto a a?al(tar. Usted llama y su pregunta ser;t contestada inmediatamente y con cortesia.
GARANTIA DE SU MAQUINA PARA HACER HIELO GE LO QUE ESTA CUBIERTO Engrape aqui la nota de caja o el cheque cancelado. Es necesario mostrar la fecha original de la compra para obtener servicio bajo garantia. GARANTIA COMPLETA POR ~ UN ANO Durante un afio a partir le de la fecha de la compra original le proporcionaremos sin cargo alguno partes y servicio de mano de obra en su hogar para reparar o reponer cualquier parte de la maquina para hacer hielo Monogram que falle a causa de alg_n defecto de fabricaci6n.
NOTAS 22