Guillotines IDEAL 7260 GB Operating Instructions
• Safety precautions • IDEAL 7260 D GB F NL I E S FIN N PL Bitte lesen Sie vor Inbetriebnahme der Maschine unbedingt diese Betriebsanleitung und beachten Sie die Sicherheitshinweise. Die Betriebsanleitung muss jederzeit verfügbar sein. Please read these operating instructions before putting the machine into operation and observe the safety precautions. The operating instructions must always be available.
• Safety precautions • D GB F NL I E S FIN N PL RUS H TR DK CZ P GR SLO SK EST CHI UAE Keine Bedienung durch Kinder! Children must not operate the machine! Pas d‘utilisation par un enfant! Geen bediening door kinderen! Non lasciare utilizzare il tagliacarte a bambini! No dejar que la utilicen los niños! Installera maskinen utom räckhåll för barn! Asentakaa laite lasten ulottumattomiin ! Installer maskinen utenfor rekkevidde for barn! Dzieciom nie wolno obsługiwać urządzenia ! D GB F NL I E S FIN N PL RUS
• Safety precautions • IDEAL 7260 D Messer nie lose liegen lassen! Messer nur mit Messerwechselvorrichtung oder im Messertransportkasten befördern! (siehe Seite 29 und 31). Warnung! Verletzungsgefahr! GB Never leave the blade unattended! Do not extract or transport the blade without protection! (See page 29 and 31). Danger! Risk of injury! F Ne jamais laisser la lame sans protections ! Elle ne doit être démontée qu’à l’ aide du dispositif de changement de lame (cf.
• Safety precautions • DK Knivbladet må aldrig efterlades uden opsyn. Forsøg ikke at afmontere eller transportere knivbladet uden beskyttelse! (Se side 29 og 31) FARE! Risiko for legemlig beskadigelse. CZ Nikdy nenechávejte nůž bez krytu. Nikdy nevyjímejte nebo neprepravujte nuz bez ochranného krytu (viz. strany 29 a 31) Nebezpecí! Riskujete zranení P Deixar a faca sempre em local seguro! Não retirar ou transportar a faca sem protecção! (Ver pág.
• Safety precautions • IDEAL 7260 D GB F Keine harten und splitternden Materialien schneiden! Do not cut hard materials or materials which may splinter! La coupe de matériaux trop durs ou risquant des projections est interdite ! NL Snij geen harde materialen of materiaal dat kan splinteren! I Utilizzare il tagliacarte esclusivamente per il taglio di risme di carta o materiali analoghi! E ¡No cortar materiales duros o materiales que puedan astillarse! S Förstör inte hârt material eller material som kan spli
• Safety precautions • The machine is designed for cutting stacks of paper to a specified size. This machine is constructed for "one-man operation" only! Warning! Clips or similar damage the cutting blade.
• Safety precautions • IDEAL 7260 A B A B All components which may endanger the operator are covered by a guard (A). Do not operate the machine without the following safety devices: • Panels, tightly screwed (A). • Safety beam guard (B). A The cutting action, which is dangerous to the operator, is protected by a two-handed control system (C) and safety beam guard (D).
• Safety precautions • Protect mains cable against heat, oil and sharp edges! A Standard machines are factory-set as follows: • Voltage 400 V (220 V) 3 phase • Frequency 50 Hz (60 Hz). Machine does not function • Is the machine switched on? • Is the key-switch on. pressed? • Is the green overload switch • Is the black overload switch pressed? • Check on-site fuse. If the machine still does not function then the rotation must be reversed. The machine is wired according to the IEC standards.
• Safety precautions • IDEAL 7260 Ensure free access to mains! When not in use for a longer period switch off. (Main switch to "0").
• Installation • The machine is delivered ready for operation. 6 strong people are required to lift the machine from the pallet. Side tables, left and right, (A) are available as accessories. Attach the side tables to the front table so that the upper surface is level. (Screws and nuts are in a plastic bag in the tool set (B). Reassemble the safety light beam. For transport through narrow doors: • Remove side tables A Danger! The machine must not be put into operation without the safety light beam.
• Installation • IDEAL 7260 Plug into socket.
• Operation • A B A B It is forbidden to operate the machine if the operating and safety instructions have not been understood. Please check the safety devices are functioning and complete before use. • All covers have to be mounted (A). • Safety beam guard must be mounted (B). • The release for cutting is allowed only if the two-hand safety device is operated at the same time (C) • Safety light beam: The machine stops immediately if anyone reaches into the cutting area (D).
• Operation • IDEAL 7260 Position the main switch to "I" (A). Insert the key for the control system and turn it to the right (B). Press button (D) machine will automatically go to 72 cm or 28,346 inches. C S The machine is now ready for use. B A The measurement is set as follows: • manually with the electric hand-wheel or button and • by programming the cutting dimensions (A). Dimension is shown on the display in inches or cm (B).
• Operation • CA B Optical cutting line indicator: Optical cutting red line (A), indicates the position of the cut. Blade cuts on the front edge (B) of the light beam. Mechanical cutting line indicator: The clamp (C) can be used as cutting line indicator for cutting. Pre-clamping can be performed using the foot pedal (D). Only use the optical cutting line indicator and mechanical cutting line indicator when no exact cut is required.
• Operation • IDEAL 7260 False clamp plate: A clamp plate (A) is fitted to the machine to prevent pressure marks on sensitive material. LED illuminates. V A B To dismount: • Remove the clamp plate (A) by turning the screwdriver (found in tool box) in the space between the clamp and clamp plate. • Store the clamp plate in the provided holder (C) LED deletes.
• Operation • The clamp moves automatically when cutting is activated. The paper can be pressed in advance, with the foot pedal. Cutting is activated by pressing both actuators (A) on the front table. B Symbols for cutting activation: Cutting sequence with automatic clamping. + A Cutting activation: Press both actuators of the two-handed control system (A) simultaneously and keep them pressed until the paper is completely cut. The safety area (B) must be free.
• Operation • IDEAL 7260 Operating elements two-handed control system A - Safety pre-clamping and cutting B - Backgauge control C - Backgauge D - Key switch E - Main switch F - Side lay left and right G - Clamp pressure adjustment H - Foot pedal I - Airtable switch J - Program number K - Program step L - LED "M" display memory M - LED "E" display eject N - LED "S" display error indication O - Display cutting size (cm or inch) P - Backgauge, backwards fast hand-wheel for fine Q - Electronical adjustment R -
• Operation • Start machine to position "I", insert the key • Main switch for the control panel and turn it to the right. button backgauge moves to • Press the rear and searches for the reference position, wait until a measurement is shown in the display (72 cm or 28,346 inches). D E C S O Warning! Before storing or cutting a measurement please check if the correct measurement scale (72 cm or 28,346 inches) see above is stored. For information on how to store see bottom picture on page 24.
• Operation • IDEAL 7260 Eject function is pressed the backgauge will If button advance to the preset measurement, ejecting the material to be cut, then automatically return to the position shown on the display. zU Adjust the eject-dimension and hold + press • Press e on display. • Insert the desired dimension. Store dimension. • p z g Multiple cut • Enter the multiple cut size on the display • Advance to the measurement with the button. • Push the paper to the backgauge . • Release the cut.
• Operation • Programming This control system enables you to store 99 programs with 99 programmable steps. One step represents one measurement or max. 9 multiple cuts. After entering the program numbers you are able to change between several program steps with the button b and j. Program on display = program number. Step on display = program step. K J The indicated program step can be overwritten at any time. These programs remain stored when the machine is off.
• Operation • IDEAL 7260 Entering a program P appears on the display. • Press ... • Enter program number . The number will be shown on the display • If measurement is shown on the display the program is reserved. • Enter a measurement or advance with the hand-wheel . Store the dimension next program step • appears. • Enter the next dimension. Store the dimension • + Escape the program mode.
• Operation • Multiple cut program • Press Q until the multiple cut size is reached (E, F usw. max. 9 mal). • Enter multiple cut size. Store the dimension. • g Example of a program with multiple cut program 09 • delete previous program • step 1 on 50 cm • •Q first multiple cut size E •Q second multiple cut size F e.g.
• Operation • IDEAL 7260 Delete a step • Choose a step number with button b or j • Press button Z twice. Delete a program • Enter program number twice. • Press button c 0 1 ... 9 9. Changing the basic settings Frequently used dimensions are stored in the control system. • w Basic setting 21 cm (8,267"). • x Basic setting 14,85 cm (5,846"). • y Basic setting 10,50 cm (4,133"). (Eject) Basic setting 20 cm (7,87"). • Changing a basic setting: • Press and hold + press w Setting blinks. • Enter new setting.
• Operation • Working with programs P appears on the display. • Press ... Enter program number. • button dimension is approached. • Press Insert paper and move by means of the paper knock-up block to the backgauge and side lay on the left . after every cut the • Release the cut backgauge advances to the next position. Release a cut see page 17. p 01 99 S b PROGRAMM P STEP S F1 F2 D I CP AM F3 E I J Correcting a measurement When a dimension has to be corrected during cutting (e.g.
• Blade and cutting stick replacement • IDEAL 7260 If the cutting quality decreases: • Check the cutting depth (see page 34). • Check the cutting stick (see page 30). • Replace or grind the blade (see page 26 - 34). The blade cannot be ground if the blade height is less than 83 mm/3,29 inches. A new blade must be used. The blade may only be ground by a qualified supplier or from the manufacturer Krug & Priester, D-72336 Balingen. Danger! Risk of injury! The blade is extremely sharp.
• Blade and cutting stick replacement • Turn the blade depth adjustment (A) towards the top until the blade screw recess corresponds with the frame recess (B). (Spanner found in tool set (C). A Remove spanner Danger! Risk of injury B C Lower the blade by pressing both cutting buttons (1.). Keep one button pressed and turn off the main switch (2.). 1. 2.
• Blade and cutting stick replacement • IDEAL 7260 The 3 eccentrics are now exposed and should be turned counter clockwise to position "0" with the special wrench and attachable extension pipe (A) (in the tool set). The slot must correspond to position "0" (B). A B Remove the special wrench and turn on the main switch until the blade returns to the home position.
• Blade and cutting stick replacement • Position the main switch to "0" (1.) Remove the 2 blade screws on the elongated holes (2.). Then put the blade changing tool (A) into place and fasten it to the blade (3.). A 3. 1. 1. 3. A Remove 4 blade screws (1.) Loosen the grips (2.) of the blade changing tool (A) lightly and allow the blade to be taken downwards out of the machine (3.). Place the blade into the blade carrier (B) and screw it into place (4). 2. B 4.
• Blade and cutting stick replacement • IDEAL 7260 Take out the cutting stick with a small screwdriver. If needed the cutting stick can be turned or exchanged. (The cutting stick can be used eight times). 1. 2. A 3. A Replacing the cutting stick (not the blade) • Turn the blade depth adjustment (A) towards the top until the blade screw recess corresponds with the frame recess. See page 27. (Otherwise the first cut will be too deep). • Remove spanner • Remove the cutting stick according to top picture.
• Blade and cutting stick replacement • Take the exchange blade carefully out of the blade box and screw it to the blade changing tool (A) • Make sure there is a space ot 10 mm or 0.39 inches! (B). • Blade must be covered! (C). Danger! Risk of injury! A 10 mm 0.39 inch B B C C Place the blade to be exchanged with the blade changing tool (A) mounted (1.), into the blade carrier and push it up to the top and screw it into place with the grips (2.). 1. A 2.
• Blade and cutting stick replacement • IDEAL 7260 Lightly tighten 4 of the 6 blade screws with washers (1.). Remove the blade changing tool (A) (2.). Lightly tighten the remaining blade screws with washers (3.). 1. 2. 3. Remove all tools and distribute paper along the entire cutting length (1.). Turn main switch to position "I" (2.). 1. 2.
• Blade and cutting stick replacement • Lower the blade by pressing both cutting buttons (1.). Keep one button pressed and turn off the main switch (2.). 1. 2. With the special wrench (A) the 3 eccentrics should be screwed down until the paper is cut along the entire length of the blade (3.) (The blade must remain parallel, not too deep into cutting stick). A 3.
• Blade and cutting stick replacement • IDEAL 7260 Turn main switch to position "I" (1.). Blade will return to upper position. Tighten 6 blade screws (2.) firmly. 2. 1. A Paper cutting test. If the last sheet or several sheets are not completely cut, gradually turn the blade depth adjustment (A) 1/12 downwards until all the paper is completely cut. Do not set too low as blade will become blunt sooner.
• Maintenance and cleaning • Danger! • Maintenance work may only be performed by trained staff. • Disconnect the mains before starting any service work or before removing the cover. Grease the backgauge (A) control weekly with a grease gun. Advance the backgauge as far as possible to the front. (Use non-resinous oil or grease).
• Maintenance and cleaning • IDEAL 7260 D E A Grease the remaining parts twice a year (see picture). The main switch must be on "0" (B). Disconnect from the mains. Remove the front upper housing (E) taking care of the cable. Remove lower panel and rear wooden panel (C). Tools in tool set. • Check oil (F). If oil is below minimum contact your dealer. • Remove any paper. D B F max C min C • Grease the machine. • Check the 4 joining bolts and 2 pushing bars for wear (D).
• Possible malfuntions • Machine does not function! Is the machine plugged in? Main switch to position "I"? (A) Control system activated? (B) (Turn key to the right) Check the units fuse and the on-site circuit breaker! Release a cut see page 17.
• Possible malfuntions • IDEAL 7260 The machine does not funktion after being moved to another position. A If the machine still does not function then the rotation must be reversed. The machine is wired according to the IEC standards. We recommend that alterations to the rotary direction be made in the socket. It is also possible to make alterations in the plug by exchanging "L1" and "L2". Danger! Incorrect exchanging of the connections will endanger the operator.
• Possible malfuntions • A B Machine turns off: • Machine overloaded. Safety button (A) ejects. Reset the safety button (A). • Machine blocked. • Blade is blunt. Eliminate the cause, and push the safety button (A). • Backgauge blocked Safety button (B) ejects. Eliminate the cause, and push the safety button (B).
• Possible malfuntions • IDEAL 7260 A Does not cut through the last sheet: • Turn or turn around the cutting stick (A), readjust the blade by means of blade depth adjustment (B) (see page 34). Poor cutting quality or blade stays in the paper stack. • Change the blade (C) (see pages 26 - 34).
• Possible malfuntions • Motor runs but blade does not move downwards. • Security brake has been activated! Inform the Service Team! • www.ideal.de "Service" service@krug-priester.
• Possible malfuntions • IDEAL 7260 No clamp pressure. • Hydraulic oil needs refilling. Contact your dealer. F max min Sender A Receiver D C B D Trouble shooting-light beam • During normal operation the LED (A) must iluminate orange and LED (B) green. • Display (C) is permanently on orange when the sender and/or receiver require cleaning. Clean the glass (D) from the sender and receiver.
• Possible malfuntions • None of the above mentioned methods helped to solve the problem: Contact Service Team under • www.ideal.de "Service" service@krug-priester.
• Accessories • IDEAL 7260 Recommended accessories: HSS - Blade • Nr. 9000 141 Cutting stick (6 pieces) • Nr. 9000 039 Blade changing tool 1 • Nr. 9000 514 Paper knock-up block 1 • Nr. 9000 521 Grease gun 1 • Nr. 9004 683 Side tables left and right • Nr. 9000 550 USB - Connection cable • Nr. 9000 557 CD - Software "Visioncut" • Nr.
• Technical data • A Technical data: • Power supply: 400V/50Hz/3~, 220V/60Hz/3~ • Cutting length: 720 mm • Cutting height: 80 mm • Table depth: 720 mm • Sound level EN 13023: 72 dB (A) • Minimum space requirement (width x depth x height) 1305/21001mm x 1500/16001mm x 1355 mm • Leakage current < 3,5mA • Power cord gauge min. 1,5mm2 (400V) • Power cord gauge AWG 14 (20A) (220V) • Clamping pressure: min.
• Technical data • IDEAL 7260 This machine is approved by independent safety laboratories and is in compliance with the EC-regulations 2006/42/EG and 2004/108/EG. Sound level information: The sound level is 72 db (A) as defined by EN 13023. Subject to alteration without notice.
D GB F EG-KONFORMITÄTSERKLÄRUNG EC-declaration of conformity Déclaration de conformité CE - Hiermit erklären wir, daß die Bauart von - Herewith we declare that - Par la présente, nous déclarons que 7260 GS- IDENT. Nr. 11072101 UL- IDENT. Nr. 10072101 - folgenden einschlägigen Bestimmungen entspricht - complies with the following provisons applying to it - sont conformes aux dispositions pertinentes suivantes 2006/42/EG: Maschinenrichtline, EC Machinery directive, EC Directives machines.
IDEAL • Made in Germany • Document Shredders • • IDEAL • 72336 Balingen • Germany • www.ideal.
