V13.3.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place it on an unstable surface. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. • The power adapter may have either a 2-prong or a 3-prong grounded plug.
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern. • Use proper handling procedures when using polymer batteries.
Preface General Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .............................................................................................................................................................I ErP Off Mode Power Consumption Statement: ........................................................................................... II FCC Statement ............................................................................................................................................
Preface System Map: LCD Panel Open - Model A ................................................................................................1-7 System Map: LCD Panel Open - Model B ................................................................................................1-8 LED Indicators ...........................................................................................................................................1-9 Hot Key Buttons (Model B) ..............................................
Preface Storage Devices, Audio & Mouse Overview ....................................................................................................................................................2-1 Hard Disk Drive .........................................................................................................................................2-2 Optical Device ...........................................................................................................................................
Preface Shut down ..................................................................................................................................................3-7 Configuring the Power Buttons .................................................................................................................3-8 Resuming Operation ................................................................................................................................3-10 Power Conservation Modes ....................
Preface Chipset .......................................................................................................................................................4-6 Video (VGA) .............................................................................................................................................4-6 NVIDIA Video (VGA) ..............................................................................................................................4-6 LAN ...............................
Preface Main Menu .................................................................................................................................................5-6 System Time & Date (Main Menu) ...........................................................................................................5-6 SATA Port # (Main Menu) ........................................................................................................................5-7 System/Extended Memory (Main Menu) ....................
Preface Exit Menu ................................................................................................................................................5-16 Upgrading The Computer Overview ....................................................................................................................................................6-1 When Not to Upgrade ................................................................................................................................
Preface PC Camera Module ..................................................................................................................................7-11 PC Camera Audio Setup ..........................................................................................................................7-12 Camera App .............................................................................................................................................7-13 Taking Pictures/Capturing Video ..............
Preface Intel® Rapid Start Technology Driver ....................................................................................................7-63 Intel® Rapid Start Technology Configuration ........................................................................................7-64 Intel® Rapid Start Technology Driver Installation .................................................................................7-70 Intel® Wireless Display Application .....................................................
Preface Resolving the “Insert a SIM” issue with the 3G Module (Windows 8) ..................................................8-12 Interface (Ports & Jacks) Overview ...................................................................................................................................................A-1 Ports and Jacks ..........................................................................................................................................A-2 Card Reader ..........................
Preface Video (VGA) ............................................................................................................................................C-1 NVIDIA Video (VGA) .............................................................................................................................C-1 NVIDIA® Optimus™ Technology ..........................................................................................................C-2 Intel® Dynamic Video Memory Technology .......................
Preface Audio ........................................................................................................................................................D-2 Keyboard & Pointing Device ....................................................................................................................D-3 Interface ....................................................................................................................................................D-3 Card Reader .....................
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you. Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide Not Included Operating Systems (e.g. Windows 8) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module.
1 Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 8 operating system is supported. Note: In order to run Windows 8 without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM).
Quick Start Guide Model Differences This notebook series includes two different model types that mainly differ as indicated in the table below. Note that your model may appear slightly different from those pictured in this manual. Feature Model A Model B Display Type Supported 15.6” (39.62cm) HD+ (1600 * 900) / FHD (1920 * 1080) 16:9 LCD Panel 17.3” (43.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. Remove all packing materials and place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Quick Start Guide System Map: LCD Panel Open - Model A 2 1 1. 2. 3. 4. 5. 4 3 7 6 4 8 8 5 6 Figure 1 - 2 LCD Panel Open - Model A 7 9 Built-In PC Camera PC Camera LED LCD Power Button Top Case LED Indicators 6. Airplane Mode Button 7. GPU Button 8. Speakers 9. Keyboard 10. Built-In Microphone 11. Touchpad & Buttons 12. Fingerprint Reader Sensor (Factory Option) 12 10 11 12 Note that the Touchpad and Buttons valid operational area is that indicated within the red dotted lines above.
1 Quick Start Guide Figure 1 - 3 LCD Panel Open Model B System Map: LCD Panel Open - Model B 2 Built-In PC Camera PC Camera LED LCD Power Button GPU Button Speakers Top Case LED Indicators 8. Hot Key Buttons 9. Keyboard 10. Built-In Microphone 11. Touchpad & Buttons 1 1. 2. 3. 4. 5. 6. 7. 5 4 3 7 8 4 6 6 8 5 7 9 11 10 11 1 - 8 System Map: LCD Panel Open - Model B Note that the Touchpad and Buttons valid operational area is that indicated within the red dotted lines above.
Quick Start Guide LED Indicators The LED indicators on the computer display helpful information about the current status of the computer.
1 Quick Start Guide Icon Color Description Green UMA Mode Activated (GPU Button) Orange Optimus Mode Activated (GPU Button) Orange NVIDIA Discrete GPU (dGPU) Activated Green Intel Integrated GPU (iGPU) Activated White Hard Disk/ODD Activity Green Airplane Mode is ON (the WLAN, Bluetooth & 3G Modules are OFF) White The Computer is Powered On Table 1 - 3 - Top Case LED Indicators Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircr
Quick Start Guide Hot Key Buttons (Model B) Press the hot key buttons on the computer to toggle the appropriate function on/off. Icon Color Description Green UMA Mode Activated (GPU Button) Orange Optimus Mode Activated (GPU Button) 1 1 Power On/Off the (optional) PC Camera 2 Mute On/Off 3 Turn On/Off Airplane Mode 2 3 Power the Computer On/Off Table 1 - 4 - Hot Key Buttons Note that Model A supports only the GPU , Airplane Mode Map: LCD Panel Open - Model A” on page 1 - 7).
1 Quick Start Guide Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work. Keyboard The keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly.
Quick Start Guide Keyboard Shortcuts The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in Windows 8.
1 Quick Start Guide Function Keys & Visual Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. Visual indicators (see the table below) are available when the Hot Key driver is installed.
Quick Start Guide Control Center When in the Windows Desktop app (not in the Start screen) press the Fn + Esc key combination, or doubleclick the icon in the notification area of the taskbar to toggle the Control Center on/off. The Control Center gives quick access to frequently used controls and enables you to quickly turn the camera/Touch Pad on/off (see Appendix B for full details). Control Center Click on any button to turn any of the modules (e.g. TouchPad, Camera) on/off.
1 Quick Start Guide Figure 1 - 6 Front & Left Views LED Indicators Security Lock Slot USB 2.0 Port S/PDIF-Out Jack Microphone-In Jack 6. Headphone-Out Jack 7. Optical Device Drive Bay System Map: Front & Left Views 1. 2. 3. 4. 5. 1 1 2 3 4 5 6 7 CD/DVD Emergency Eject Sound Blaster Cinema Audio Note that you will need to install the Sound Blaster audio application in order to get maximum audio performance. If you need to manually eject a CD/DVD (e.g.
Quick Start Guide System Map: Right & Rear Views 1 6 2 Figure 1 - 7 Right & Rear Views 3 4 5 8 7 1. Multi-In-1 Card Reader 2. 2 * USB 3.0 Ports 3. Combined eSATA/ USB 3.0 Port 4. HDMI-Out Port 5. RJ-45 LAN Jack 6. External Monitor Port 7. DC-In Jack 8.
1 Quick Start Guide Figure 1 - 8 Bottom View Model A 1. 2. 3. 4. System Map: Bottom View - Model A Component Bay Cover Battery Primary HDD Bay Fan Outlet/Intake 1 4 4 Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 12 for full instructions. 3 2 CPU The CPU is not a user serviceable part.
Quick Start Guide System Map: Bottom View - Model B 1. 1 4 2. 3. 4. 4 2 Figure 1 - 9 Bottom View Component Bay Cover Battery Primary HDD Bay Fan Outlet/Intake 3 Battery Information CPU The CPU is not a user serviceable part. Overheating To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use. Always completely discharge, then fully charge, a new battery before using it.
1 Quick Start Guide Windows Control Panel Throughout this manual you will see an instruction to open the Control Panel. In Windows 8 right-click the lower left hot corner to bring up the context menu (or use the Windows Logo Key + X key combination) and select Control Panel. Swipe a finger from the right of the Touchpad from the Desktop (not the Start screen) to access the Charms Bar, click Settings and click Control Panel.
Quick Start Guide Windows 8 Start Screen & Desktop The Apps, control panels, utilities and programs within Windows 8 are accessed from the Start screen and/or Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination).
1 Quick Start Guide Apps & Tiles The Windows 8 Start screen will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary Apps. Accessing Pining/Unpinning All Apps You can add and remove the tiles for apps and control panels in the Start screen. Right-click on a blank area of the Start screen, and you will see the All Apps icon.
Quick Start Guide Desktop Application When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop app. To do so move your mouse to hover over the bottom left corner of the screen and click the pop-up. When you move to the lower left hot corner in the Start screen itself it will take you back to your most recently used app.
1 Quick Start Guide Display Most Recently Used Apps When the Desktop app is running you can right-click the lower left hot corner (or use the Windows Logo Key + X key combination) to bring up an advanced context menu of useful features such as Control Panel, Programs and Features, Power Options, Task Manager, Search, Windows Explorer, Command Prompt, Device Manager and Network Connections etc.
Quick Start Guide Windows 8 Charms Bar The right side of the screen displays the Windows 8 Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.
1 Quick Start Guide Charms Bar Items • Search results. • Share : You can search for any file, application, Apps and control panel settings with instantaneous : This button is used to share information with people via mail or social networks. • Start : Click to bring up the Start Menu (the same function as pressing the Windows Logo Key or clicking the bottom left of the screen). • Devices : Click this button to change connected peripheral device settings e.g. an external display.
Quick Start Guide Windows 8 Control Panel In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel can be accessed in a number of ways in Windows 8. • Click/ Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type Control Panel and select it from the results to the left.
1 Quick Start Guide • When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows Charms Bar and select Control Panel from the menu. Figure 1 - 19 - Settings Charms Bar (Desktop App Only) • Right-click on a blank area of the Start screen, or swipe a finger from the top or bottom of the touch screen. Click the All Apps icon and click Control Panel.
Quick Start Guide • Right-click the lower left hot corner to bring up the menu and select Control Panel (see Figure 1 - 14 on page 1 - 24). Keyboard Shortcut to Control Panel You can also use keyboard shortcuts to access the Control Panel. Press the Windows logo key and X to bring up the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key and R to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel.
1 Quick Start Guide Windows 8 Taskbar In many instances throughout this manual you will see an instruction to access the notification area of the taskbar. In Windows 8 the taskbar is accessed from the Desktop application. If you are in the Start screen you will need to click the Desktop app to switch to the Desktop. The taskbar is displayed at the bottom of the desktop screen, and you can see the notification area of the taskbar in the bottom right of the screen.
Quick Start Guide Video Features NVIDIA® Optimus™ Technology NVIDIA® Optimus™ technology is a seamless technology designed to get best performance from the graphics system while allowing longer battery life, without having to manually change settings. When the computer is in Optimus Mode it will automatically switch between the integrated UMA (Unified Memory Architecture) GPU (iGPU) and the discrete GPU (dGPU) when required by the applications in use.
1 Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows 8 when running the Desktop app (see “Desktop Application” on page 1 23). In Windows 8 it is possible to quickly configure external displays from the Devices menu item in the Charms Bar (see “Windows 8 Charms Bar” on page 1 - 25). To Configure Displays from Devices (Charms Bar): 1. 2. 3. 4.
Quick Start Guide To access Display (Control Panel) and Screen Resolution in Windows 8: 1. 2. 3. Go to the Control Panel. Click Display (icon) - In the Appearance and Personalization category. Adjust resolution. Right-Click Desktop App 2 1 3 1. You can right-click the desktop and select Screen resolution 1 (Figure 1 - 23). 2. Use the dropbox to select the screen Resolution 2 (Figure 1 - 23). 3. Click Advanced settings 3 (Figure 1 23) to bring up the Advanced properties tabs.
1 Quick Start Guide To access the Intel(R) Graphics Control Panel: 1. 2. Click Advanced settings 3 (Figure 1 - 23 on page 1 - 33) in the Screen Resolution control panel in Windows. Click the Intel(R)... tab and click Graphics Properties (button) 4 (Figure 1 - 24 on page 1 - 34) . OR 3. Right-click the desktop and select Graphics Properties from the menu. OR 4. Click the icon in the notification area of the Desktop taskbar and select Graphics Properties from the menu.
Quick Start Guide To access the NVIDIA Control Panel: 1. Right-click the desktop and select NVIDIA Control Panel 5 (Figure 1 - 25). OR 2. Double-click the icon 6 (Figure 1 - 25) in the Windows control panel.
1 Quick Start Guide Power Options Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Settings in the Charms Bar in Windows 8 may be used to Shut down or Restart (you can also add Hibernate/ Sleep to the menu - see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 9). Shut Down, Restart or Sleep 1. 2. 3. Go to the Charms Bar and click Settings. Click Power . Select Sleep, Shut Down or Restart.
Quick Start Guide Running Apps To run apps in Windows 8 you will need to check that the Screen Resolution and User Account Control Settings are compatible with the system requirements. Screen Resolution Settings 1. 2. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination). Right-click a blank area of the Windows Desktop and select Screen Resolution.
1 Quick Start Guide User Account Control Settings If your computer meets the minimum screen resolution requirements, and still you can't run Metro apps, then that you have to check the status of User Account Control (UAC). Metro apps may fail to open when the UAC is turned off. To check whether the UAC is on or off, follow the instructions below. 1. 2. 3. 4. Open the Control Panel.
Storage Devices, Audio & Mouse Chapter 2: Storage Devices, Audio & Mouse Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • Hard Disk Drive Optical Device Multi-in-1 Card Reader Audio Features TouchPad and Buttons/Mouse Overview 2 - 1 2
Storage Devices, Audio & Mouse 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Figure 2 - 1 Hard Disk Location 2 - 2 Hard Disk Drive Hard Disk Drive The hard disk drive(s) is(are) used to store your data in the computer.
Storage Devices, Audio & Mouse Optical Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see “Storage” on page D - 2). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 14).
Storage Devices, Audio & Mouse 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Disk Eject Warning Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.
Storage Devices, Audio & Mouse DVD Regional Codes To change the DVD regional codes: 1. 2. 3. Go to the Control Panel Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.
Storage Devices, Audio & Mouse 2 Card Reader Cover Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. Push-Push Card Reader Multi-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Storage Devices, Audio & Mouse Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, from the HD VDeck icon on the desktop or VIA HD Audio Deck control panel . The volume may also be adjusted by means of the Fn + F5/F6 key combination. Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer). Click the volume icon in the taskbar to check the setting.
Storage Devices, Audio & Mouse 2 Expert Mode will allow you to access more advanced configuration menus for Speaker, Microphone and Stereo Mix. Syncing Left & Right Volume Balance If you wish to adjust the left and right channel volume levels separately, you will need to adjust this from the VIA HD Audio Deck in Expert Mode. Click Speaker in VIA HD Audio Deck (in Expert Mode) and click the Sync Left and Right volume button (see left).
Storage Devices, Audio & Mouse TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details.
Storage Devices, Audio & Mouse 2 TouchPad Scrolling This computer model series may feature different TouchPad versions. Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 6) you can configure the functions from the Mouse control panel in Windows, or by doubleclicking the TouchPad driver icon in the notification area of the taskbar in the Desktop app. You may then configure the TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options to your preferences.
Storage Devices, Audio & Mouse Gestures and Device Settings The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the Touchpad to perform specific actions to manipulate documents, objects and applications. You can configure the settings from the Device Settings tab in Mouse Properties: 1. 2. 3. 4. Go to the Control Panel. Click Mouse (Hardware and Sound). Click Device Settings (tab) and click Settings.
Storage Devices, Audio & Mouse Disabling the Touchpad If you need to disable the Touchpad for any reason (e.g. you may find that when using the computer’s internal keyboard you accidentally trigger the Touchpad when resting your wrists or palms on it) you can do so by using Fn + F1 key combination. 2 You can also set the system to automatically disable the internal Touchpad when an external USB point device (e.g a USB mouse) is attached. 1. 2. 3. 4. Go to the Mouse Properties control panel.
Storage Devices, Audio & Mouse Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the TouchPad surface and slide both fingers in the direction required (in a straight continuous motion). 2 Figure 2 - 10 Scrolling Gesture Zooming The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality.
Storage Devices, Audio & Mouse Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 Forced Off If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off. The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options (Hardware and Sound) in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 10 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 2 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management 3 Wake On LAN Support (Windows 8) Wake-On-LAN is only supported from Sleep or Hibernate states in Windows 8. If you require your computer to wake up from network activity in Windows 8 then make sure that the computer is either in Sleep or Hibernate. Wake-On-LAN is not supported from Shutdown states in Windows 8. Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. It is recommended that you enable a password on wake up in order to protect your data.
Power Management Adding Hibernate/Sleep to the Power Menu Add Hibernate/Sleep to the Power Menu as follows. 1. 2. 3. 4. 5. Go to the Power Options (Hardware and Sound) control panel (see page 1 - 23). Click “Change settings that are currently unavailable” . Click Choose what the power buttons do. Click to put a tick in the Hibernate/Sleep box under Shutdown settings. Click Save Changes and close the control panel.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo).
Power Management Power Conservation Modes This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. Adjust Power Conservation Modes from the Control Center: 1. 2. 3. Press the Fn + Esc key combination to toggle the Control Center on/off. Click either the Performance, Balanced or Energy Star button.
Power Management Ctrl + Alt + Delete Key Combination You can use the CTRL + ALT + DEL key combination from almost any of the Windows 8 interfaces/Apps to bring up a full-screen displaying Lock, Switch User, Log off, Change a password and Task Manager options. If you click the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep, Shut down, and Restart.
Power Management Battery Information Follow these simple guidelines to get the best use out of your battery. Low Battery Warning Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure 3 - 3 on page 3 - 5).
Power Management 3 Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display.
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery” on page 6 - 4.
Power Management 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 1. 2. 3 Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management 3 How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation 1. 2. 4 3. 4. Insert the Device Drivers & Utilities + User’s Manual disc into the computer’s DVD drive. Click the message “Tap to choose what happens with this disc.” Click Run autorun.exe. Click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu. Figure 4 - 1 - Drivers Installer Screen 1 4 - 2 Driver Installation 5. 6. 7.
Drivers & Utilities Win 8 System Driver Page # Optional Page # Chipset Page 4 - 6 Setting Up SATA RAID or AHCI Mode Page 7 - 2 Video (VGA) Page 4 - 6 PC Camera Module (No driver required) Page 7 - 11 NVIDIA Video (VGA) Page 4 - 6 Wireless LAN Module Page 7 - 19 LAN Page 4 - 6 Fingerprint Reader Module (Model A Computers Only) Page 7 - 27 Card Reader Page 4 - 6 Bluetooth & WLAN Combo Module Page 7 - 51 TouchPad Page 4 - 6 Intel® Rapid Storage Technology (required for hard disks in A
Drivers & Utilities Manual Driver Installation Click Browse CD/DVD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder. 4 Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See “Windows Update” on page 4 8 for instructions.
Drivers & Utilities User Account Control If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as directed. Windows Security Message If you receive a Windows security message as part of the driver installation process. Just click “Install this driver software anyway” or “Install” to continue the installation procedure.
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu. 4 Chipset 1. Click 1.Install Chipset Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. Video (VGA) 1. Click 2.Install VGA Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. NVIDIA Video (VGA) 1. Click 3.
Drivers & Utilities Airplane 1. Click 7.Install Airplane AP > Yes. 2. Click Next. 3. Click Finish to restart the computer. Hot Key 1. Click 8.Install Hotkey AP > Yes. 2. Click Next > Next. 3. Click Finish > Finish to restart your computer. MEI Driver 1. Click 9.Install MEI Driver > Yes. 2. Click Next > Yes > Next. 3. Click Finish. Audio 1. Click 10.Install Audio Driver > Yes. 2. Click Next. 3. Click the button to agree to the license and click Next. 4. Click Next > Next > Next. 5.
Drivers & Utilities Windows Experience Index 4 After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experience Index (make sure the AC/DC adapter is plugged in): 1. Go to the Control Panel. 2. Click Performance Information and Tools (System and Security > System > Windows Experience Index). 3. Click “Rate this computer/Refresh Now/Rerun the assessment”. 4. The computer will take a few minutes to assess the system performance. 5. Close the control panel.
Drivers & Utilities Optional Drivers See the pages indicated in Table 4 - 1, on page 4 - 3 for the driver installation procedures for any modules included in your purchase option. 4 Models A & B Figure 4 - 3 - Optional Drivers Installer Screen Note that you need to install both the WLAN & Bluetooth drivers for all the Bluetooth Combo modules.
Drivers & Utilities 4 4 - 10
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities The Power-On Self Test (POST) If you enable the Boot-time Diagnostic Screen in the Setup Utility, each time you turn on the computer the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). 5 As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized distributor/supplier as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities BIOS Settings Warning 5 Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Previous Values with , or Optimized Defaults with . The Setup Utility The Aptio Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration).
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box at the bottom right side of the screen. Setup Menus The Setup menus shown in this section are for reference only.
BIOS Utilities Main Menu Figure 5 - 2 Main Menu 5 System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed. 5 MB Series / BIOS Revision / KBC/EC Firmware Revision (Main Menu) This item contains information on the BIOS version and video card etc., and is not user configurable.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu 5 Advanced Chipset Control (Advanced Menu) The sub-menu here allows you to adjust the Bluetooth Power Setting.
BIOS Utilities Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) You can adjust the Bluetooth module power setting to your preference. The default setting (Disabled) will see the Bluetooth module powered off when the system is started up or restarted. Enabling the power setting will have the module retain the last power status (on or off) before any restart or shut down. Intel(R) Rapid Start Technology (Advanced Menu) Enable/disable Intel(R) Rapid Start Technology from this menu.
BIOS Utilities SATA Mode Selection 5 If you have installed the Windows operating system with either IDE, AHCI or RAID mode enabled, DO NOT disable the set mode (if you wish to disable the set mode you will need to reinstall the Windows OS). Intel Anti-Theft Technology (Advanced Menu) Anti-Theft Technology, which is built-in to the processor of the computer, allows system administrators to render your computer useless to thieves by sending a poison pillencrypted SMS message over a 3G network etc.
BIOS Utilities Boot Logo (Advanced Menu) Use this menu item to enable/disable the Boot Logo screen at system startup if you have not enabled UEFI Boot. If you disable the Boot Logo you will not see the F2 Enter Setup or F7 Boot Options prompts on the screen, however you can still press these keys, while the boot screen is displayed, to perform the Enter Setup or Boot Option functions. When UEFI Boot is enabled, then the prompts to press F2 or F7 will not appear.
BIOS Utilities Security Menu Security Menu 5 The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Figure 5 - 4 Security Menu Set Supervisor Password (Security Menu) You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility).
BIOS Utilities Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance. Note: You can only set the user password after you have set the supervisor password. Password on boot: (Security Menu) Specify whether or not a password should be entered to boot the computer (you may only set a password on boot if a supervisor password is enabled).
BIOS Utilities Boot Menu Figure 5 - 5 Boot Menu 5 BIOS Screens Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS. BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages. 5 - 14 Boot Menu When you turn the computer on it will look for an operating system (e.g.
BIOS Utilities Boot Option Priorities (Boot Menu) Use the arrow keys to move up and down the menu, and press enter to select a device from the menu (the selected device will be highlighted in white). UEFI Boot (Boot Menu > OS Select) Enable/disable UEFI Boot from this menu. The Unified Extensible Firmware Interface (UEFI) specification provides a clean interface between operating systems and platform firmware at boot time. In contrast to BIOS, UEFI defines a set of standard boot and runtime services.
BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu 5 Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). You must also remove your battery in order to prevent accidentally turning the machine on. Before removing the battery disconnect the AC/DC adapter from the computer. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
Upgrading The Computer Warranty Warning Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty. Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. Before removing the battery disconnect the AC/ DC adapter from the computer first. 1. 2. 3. 4. Turn the computer off, remove the AC/DC adapter and turn it over.
Upgrading The Computer Removing the Component Bay Cover 1. 2. Turn off the computer, and turn it over and remove the battery. Locate the component bay cover and remove screws 1 - 3 .
Upgrading The Computer 3. 4. Slide the cover in the direction of arrow 4 , until the case markers 5 line up. Remove the component bay cover 6 .
Upgrading The Computer Replacing the Component Bay Cover 1. 2. 3. Reinsert the component bay cover by placing it on the bottom case assembly and sliding it on to the case in the direction of arrow 7 . Make sure the case markers 8 line up. Replace screws 1 - 3 (Figure 6 - 2 on page 6 - 5).
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer Removing the Hard Disk from the Primary HDD Bay 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery (see page 6 - 4). Remove screw 1 . Slide the HDD cover in the direction of arrow 2 until the case markers 3 line up. Lift the HDD cover out of the computer 4 .
Upgrading The Computer 5. HDD Insulation Plates 6 Note that the HDD insulation plates for the primary and secondary hard disks, though similar in outward appearance, are NOT interchangeable. The plates are clearly marked 1ST HDD & 2nd HDD. 6. 7. 8. Slide the hard disk assembly 5 forward, and remove the assembly from the computer. Remove screws 6 & 7 and the primary HDD insulation plate 8 . Reverse the process to install a new disk and do not forget to reinstall the insulation plate.
Upgrading The Computer Removing the Hard Disk from the Secondary HDD Bay 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery and component bay cover (see pages 6 - 4 & 6 - 5). Remove screws 1 & 2 from the secondary HDD assembly. Slide the HDD assembly in the direction of arrow 3 . Lift the HDD assembly out of the computer 4 .
Upgrading The Computer 5. Remove screws 5 & 6 and separate the case bracket 7 and the insulation plate 8 . 8 Figure 6 - 8 Secondary Hard Disk Case Bracket & Insulation Plate Removal 6 6 7 5 6. 7. 8. 9. Reverse the process to install a new disk (pay careful attention to the orientation of the hard disk in the case bracket before tightening the screws). Insert the new HDD into the case along with the insulation plate and replace the crews.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device The procedure for removing the optical device will depend upon your particular computer model: • See “Removing the Optical Device Drive for Model A Computers” on page 6 - 14. • See “Removing the Optical Device Drive for Model B Computers” on page 6 - 15.
Upgrading The Computer Removing the Optical Device Drive for Model A Computers 1. 2. Turn off the computer, and turn it over and remove the battery and primary hard disk bay cover (see pages 6 - 9 & 6 - 5). Remove the screw at point 1 , and use a screwdriver to carefully push out the optical device at point 2 . Figure 6 - 9 6 1 Removing the Optical Device (Model A) 2 3. 4. 2 Reverse the process to install the new device. Replace the component bay cover (see page 6 - 7).
Upgrading The Computer Removing the Optical Device Drive for Model B Computers 1. 2. Turn off the computer, and turn it over and remove the battery and component bay cover (see pages 6 - 4 & 6 - 5). Remove the screw at point 1 , and use a screwdriver to carefully push out the optical device at point 2 . 2 2 Figure 6 - 10 Removing the Optical Device (Model B) 1 3. 4. Reverse the process to install the new device. Replace the component bay cover (see page 6 - 7).
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDR III (DDR3) type memory modules (see “Memory” on page D - 2). The total memory size is automatically detected by the POST routine once you turn on your computer. 6 Note that three SO-DIMMs are only supported by Quad-Core CPUs; Dual-Core CPUs support two SO-DIMMs maximum (see “Memory” on page D - 2 for full details).
Upgrading The Computer 1. 2. Turn off the computer, and turn it over and remove the battery and component bay cover (see pages 6 - 4 & 6 - 5). The memory sockets will be visible at point 1 on the mainboard. Figure 6 - 11 RAM Module Location Contact Warning 1 3. Gently pull the two release latches ( 2 & 3 ) on the sides of the memory sockets) in the direction indicated below. 2 3 Be careful not to touch the metal pins on the module’s connecting edge.
Upgrading The Computer 4. Figure 6 - 13 6 The RAM module will 4 pop-up, and you can remove it. RAM Module Removal Single Memory Module Installation If your computer has a single memory module, then insert the module into the Channel 0 (JDIMM1) socket. In this case this is the lower memory socket (the socket closest to the mainboard). Contact Warning Be careful not to touch the metal pins on the module’s connecting edge.
Modules Chapter 7: Modules Overview This chapter contains the information on the various modules (some of which are optional) which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
Modules RAID Hard Disks All hard disks in a RAID should be identical (the same size and brand) in order to prevent unexpected system behavior. SATA Mode Selection 7 The SATA mode selection should be made before installing your operating system. DO NOT change your selected SATA mode unless you intend to reinstall your operating system. Make sure you have backed up all your data before doing so.
Modules RAID Level Description Table 7 - 1 RAID 0 Identical drives reading and writing data in parallel to increase performance. RAID 0 implements a striped disk array and the data is broken into blocks and each block is written to a separate disk drive. RAID Levels RAID 1 Identical drives in a mirrored configuration used to protect data. Should a drive that is part of a mirrored array fail, the mirrored drive (which contains identical data) will handle all the data.
Modules SATA RAID Setup Procedure (Windows 8) To configure your RAID (Redundant Array of Independent Disks) system in Striping (RAID 0) or Mirroring (RAID 1) modes (see Table 7 - 1, on page 7 - 3) you will require at least two identical (see sidebar) hard disks. Note that the RAID setup in Windows 8 differs from that outlined for Windows7. You need to setup a RAID before installing your Windows 8 operating system, and you will need to prepare the following in order to do so. 7 1. 2. 3. 4. 5. 6.
Modules 1. 2. 3. Go to the operable computer and insert a USB Flash drive or external USB hard disk. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive of the operable computer. Copy the f6flpy-x86 or f6flpy-x64 folder from the location below (D: denotes your DVD drive) on the Device Drivers & Utilities + User’s Manual disc to the USB flash drive or external USB hard disk. • For Windows 8 32bit = D:\Options\RAID\f6flpy-x86 • For Windows 8 64bit = D:\Options\RAID\f6flpy-x64 4.
Modules 13. You can now setup your RAID volume using any two installed disks. 14. Go to Name: and press . 15. Type a name of your choice for your RAID volume and press .
Modules 16. Go to RAID Level: and press . 17. Choose the RAID Level required (see Table 7 - 1, on page 7 - 3 for details) and press . • RAID0 (Stripe) • RAID1 (Mirror) • Recovery 18. Go to any of the disks listed under Select Disks: and select a disk name and press . 19. Move the cursor down (use the arrow keys) onto to X (o select the disk required and press .
Modules 20. You should select two identical disks to form your RAID volume. 21. If you have selected RAID0 (Stripe) then you can adjust the “Strip Size” to your requirements. 22. If you have selected Recovery then you can adjust the Synchronization to “On Request” or “Continuous”. 23. Go to Create Volume and press . 24. The RAID volume will then be created and the RAID information will be displayed under Intel(R) Rapid Storage Technology (in the Advanced menu).
Modules 25. Press to exit the menu. 26. Press and to “Save Changes and Reset”, however ensure that the two conditions in the bulleted points below are met before doing so. • Make sure the Windows 8 OS DVD is in the DVD drive. and as the computer starts up it will automatically boot from the Windows 8 OS DVD (you will be prompted to press a key to boot from the DVD). • Make sure your USB Flash drive or external USB hard disk is attached to one of the USB ports on the computer. 27.
Modules 35. Install the Windows drivers from the Device Drivers & Utilities + User’s Manual disc as per Table 4 - 1, on page 4 - 3 (make sure you install the Intel Rapid Storage Technology driver - see overleaf). 36. Run the Intel® Rapid Storage Technology application to manage your RAID volume as instructed in “Intel® Rapid Storage Technology for RAID Systems” on page 7 - 58. 7 IRST Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2.
Modules Deleting a RAID (Windows 8) If you wish to delete an existing RAID then follow the procedure below to do so. However backup up any necessary files and data before deleting a RAID, as doing so will result in the loss of all data on the RAID volumes. 1. 2. 3. 4. 5. Start-up your notebook computer and press to enter the BIOS. Go to Intel(R) Rapid Storage Technology (in the Advanced menu) and press . Go to the RAID (listed under RAID Volumes:) and press .
Modules PC Camera Module When the PC Camera application is run the LED indicator to the left of the camera will be illuminated in red (see 2 Figure 1 - 2 on page 1 - 7/Figure 1 - 3 on page 1 - 8). Note that you need to use the Camera app in Windows 8 to take pictures and capture video. Use the Fn + F10 key combination (see “Function Keys & Visual Indicators” on page 1 - 14) to toggle power to the PC Camera module.
Modules PC Camera Audio Setup If you want to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. 5. 6. Go to the Control Panel. Click Sound (Hardware and Sound) and click Recording (tab). Right-click hold and release Microphone (VIA High Definition Audio) and make sure the item is not disabled. Double-click Microphone (or select Properties from the right-click menu).
Modules Camera App 1. 2. 3. Make sure the camera is powered on (use the Fn + F10 key combination to toggle power to the camera module). Click the Camera app icon in the Start screen to run the Camera app . The camera interface is a translucent app bar with three buttons. Figure 7 - 7 Camera App Bar • Camera options:.
Modules You can also click on More to adjust Brightness, Contrast and Flicker (if you find that the video screen in the camera program is flickering, you can try to adjust the setting here). Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in Flicker under More Options.
Modules Taking Pictures/Capturing Video 1. 2. 3. 4. 5. 6. 7. Make sure the camera is powered on (use the Fn + F10 key combination to toggle power to the camera module). Click the Camera app icon in the Start screen to run the Camera app . Click to select the timer if you require a countdown before capture. Click to select either photo or video modes. Click in the main window to take a picture or start video capture (if video capture begins a timer will appear in the bottom right corner of the screen).
Modules 8. A scroll arrow will appear on the left side of the screen after any pictures/videos have been captured. 9. Click the arrows (on either side of the screen) to browse through the captured photos/video, and back to the Camera app. 10. Clicking on a captured photo will bring up an app bar with Crop and Delete buttons. Figure 7 - 11 Crop & Delete Buttons (for Still Photos) 11. Use the handles to Crop any captured picture, and click OK to save the changes made. 12.
Modules Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules Wireless LAN Module If you have included an Intel® or 3rd Party WLAN module in your purchase option make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules.
Modules 3rd Party 802.11b/g/n Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4. Click Next. 5. Click Finish to restart the computer. 6. The operating system is the default setting for Wireless LAN control in Windows (see page 7 - 21). 7 Intel® WLAN Driver Installation 1.
Modules WLAN Configuration in Windows 8 You can configure a wireless connection using one of the following options, however make sure the Wireless LAN module is turned on (and not in Airplane Mode) before configuration begins. Charms Bar 1. 2. 3. Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off). A list of available access points will appear.
Modules 4. 5. 6. 7. 8. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not. When you are connected to the network access point it will display the Connected icon . Select any connected network and click Disconnect to disconnect from a connected access point. 7 Figure 7 - 14 Networks Connected / Disconnect 9.
Modules 11. You need to either use Airplane Mode, or to turn the WLAN module off aboard aircraft.
Modules Desktop Mode 1. 2. 3. 4. 5. 6. 7. Switch to the Windows Desktop (click the app or use the Windows logo key D key combination). Click the wireless icon in the notification area of the taskbar. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not.
Modules Control Panel If you are in Category View do the following (see over for Icon View): 1. 2. 3. Open the Control Panel. Click the Network and Internet control panel. Click Connect to a network. Figure 7 - 17 Network and Internet Control Panel 4. 5. 6. 7. 8. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next.
Modules If you are in Icon View do the following: 1. 2. 3. 4. Open the Control Panel. Click Network and Sharing Center. Click Change Adapter Settings. Double-click Wi-Fi. 5. 6. 7. 8. 9. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not.
Modules Fingerprint Reader Module (For Model A Computers Only) The optional fingerprint reader application software provides a high level of security for your computer. Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. A further level of security and control is provided in the BIOS (see “Security Menu” on page 5 - 12).
Modules There are two fingerprint applications supplied with this model. Install the driver from the Device Drivers & Utilities + User’s Manual disc and follow the appropriate instructions on the following pages. • See overleaf for driver installation on the two applications. • See pages 7 - 30 to 7 - 39 for information on the AuthenTec TrueSuite application. • See pages 7 - 40 to 7 - 50 for information on the BioExcess application.
Modules AuthenTec TrueSuite Fingerprint Reader Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers. 3. Click 2.Install Finger Print Driver > Yes. 4. Click Next. 5. Click Finish to restart the computer. 6. See “AuthenTec TrueSuite Application” on page 7 - 30 for more information. BioExcess Fingerprint Reader Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2.
Modules Fingerprint Enrollment Note that it is strongly recommended that you enroll more than one finger in case of injury etc. AuthenTec TrueSuite Application The AuthenTec TrueSuite application is used in conjunction with your fingerprint reader to enroll fingerprints and manage settings etc. User Enrollment 1. 2. 3. 4. 5. 7 Figure 7 - 19 6. Run the AuthenTec TrueSuite application. Click Yes when you have identified your fingerprint reader sensor ( 12 in Figure 1 - 2 on page 1 - 7).
Modules 7. You will be prompted to select another finger for enrollment (it is recommended that you enroll a number of fingers - see sidebar). 8. Click the button to continue once you have enrolled a number of fingerprints. 9. Enter the required information and click the button to register your software, or click to register later. 10. Your fingerprints will now be enrolled (you may enroll any additional fingerprints at any time). Help Click the Help icon and select a help topic from the drop-down menu.
Modules Settings Click the Settings button on the menu bar to access the personalization settings for AuthenTec TrueSuite. Here you can choose to enable/disable Website Log On, QuickLaunch, Fast User Switching and the desktop icon. You can also select the Theme and export/import identities. Click the Save button to save any changes made.
Modules Windows Log On Windows log on allows you to gain access to your computer by swiping your finger across the fingerprint reader sensor. Use the Biometric Devices control panel (in the Hardware & Sound category) in Windows to turn Biometrics on/off when required. Access the Biometric Devices control panel and select Change biometric settings to turn the biometrics on or off, or to allow users to log on to Windows using fingerprints.
Modules Website Log On Use a fingerprint swipe to log on to websites to help you avoid having to remember user names and passwords across multiple websites (browsers supported are Internet Explorer, Firefox and Chrome). Registering a Website 1. 2. 3. 4. Use your web browser to navigate to the website required. Enter your user name and password and sign in to the website. An AuthenTec TrueStudio dialog box will pop-up. Click Save Password to register the website. 5.
Modules QuickLaunch QuickLaunch allows you to drag and drop icons (which represent websites, folders, applications and/or computer actions) to any enrolled finger and then swipe your finger to launch the icons assigned to that finger. 1. 2. 3. 4. 5. Run the AuthenTec TrueSuite application. Click Select Category (button) to group icons if required. Drag and drop an icon to an enrolled finger. To launch the website, folder, application and/or action just swipe your finger across the sensor.
Modules Adding a Website to QuickLaunch 1. 2. 3. 4. 5. 7 Run the AuthenTec TrueSuite application. Click the Add Website button on the menu bar and the dialog box will be displayed. Enter the website URL, name, icon and category as required. Click Save and an icon will be associated with the selected website. To delete an icon right-click it and select Delete Icon and it will no longer be associated with the finger.
Modules Dock View Dock View displays the website icons across the bottom of the screen. Each icon wiLl have an associated web card which displays the website information, user name and password etc. This information may be edited or deleted as required. Figure 7 - 27 Dock View Editing a Web Card 1. 2. 3. 4. 5. 6. 7. Run the AuthenTec TrueSuite application. Left-click a web card to bring up the associated information. You can click the reveal/hide password button to see or hide the password.
Modules Exporting and Importing Your Identity You can export your identity to backup your information, or to move it to another computer. Exporting Your Identity 1. 2. 3. 4. 5. 6. 7 Run the AuthenTec TrueSuite application. Click the Settings button on the menu bar. Click Export My Identity. You will be required to enter and confirm a passphrase and click Next. Browse to a location to Save the file. Swipe a finger to confirm the export. Importing Your Identity 1. 2. 3. 4. 5. 6. 7.
Modules AuthenTec KeepSafe The KeepSafe folder is an encrypted area assigned on your hard drive that allows you to store files and folders to be protected by fingerprint protection. The folder will appear on your desktop (if selected in the Personalization Settings) and in My Computer, but will not be visible to other users of your computer. To lock/unlock the KeepSafe folder right-click it to display the context menu and select Unlock/Lock.
Modules BioExcess Application The BioExcess application is used in conjunction with your fingerprint reader to enroll fingerprints and manage settings etc. User Enrollment 1. 2. 3. 4. Run the BioExcess application from the Start screen. Identify your fingerprint sensor ( 11 Fingerprint Reader Module in Figure 1 - 2 on page 1 - 6). Click Next when the Initial Wizard appears. Swipe a finger to practice enrollment (click Next to skip this step).
Modules 5. 6. 7. 8. Enter your Windows log on password, and then click Next. Click on the fingerprint diagram to select any finger to enroll. Swipe the finger until the finger is enrolled and then repeat for other fingers. Click Next to continue once you have enrolled a number of fingerprints. Fingerprint Enrollment Note that it is strongly recommended that you enroll more than one finger in case of injury etc.
Modules BioExcess Control Center Run BioExcess application and swipe a registered finger to run the Control Center (or swipe a finger across the fingerprint sensor and select Control Center from the BioExcess Menu).
Modules Use the Control Center to adjust all the BioExcess application settings. Click on any of the menu headings to access the sub-menu to adjust functions or settings including Fingerprint Management, Data Protection, Online Accounts Management, General settings and Information. Help Click the Help icon and select a help topic from the drop-down menu. Select a topic from the Contents menu or Search for help on a specific area.
Modules Fingerprint Management Fingerprint Enrollment: You can add or delete enrolled fingers by clicking in the box above any of the fingers. Application Launcher: Use any of your fingers to launch any chosen application, website, online account or use Launch Express to launch functions such as Shut Down, Windows Lock etc. Click OK to save any changes made to these settings. • Click on any of the boxes above an enrolled finger and select the item from the drop-down menu.
Modules • Simply drag and drop an executable file onto any enrolled fingers to launch an application, or click and select Launch Application and then browse to the executable file. • Select Launch Web Site and then input the URL to use a finger to go to any website. • Auto Login will prompt you to choose an account to select to login to when a finger is swiped. • Launch Express will allow you select one of a number of functions (e.g. shutting down the computer) when the appropriate finger is swiped.
Modules Data Protection File Encryption/Decryption: Click Add or drag and drop any file for encryption/ decryption. Click Encrypt and you will be asked for a backup pass ow rd for the file. You can right-click any file and select Decrypt/Encrypt File from the BioExcess item in the menu. See the Help file for further information. Secure Drive Access: You can access your secure drive here.
Modules Online Accounts Management You can store user IDs and passwords for websites and/or applications and the software will then automatically fill in your log on and password information for you when you swipe your finger. When you visit a registered website or program you will see a BioExcess icon in the top left of the screen prompting you to swipe a finger to log on. See Help for more information on registering and managing online accounts.
Modules General Settings User Settings: Fast User Switch enables multiple users to switch to their own Windows environment with the swipe of a finger. Use Pre-Boot Authentication to prevent the Windows OS from loading until the password has been confirmed. Password Settings: You can change your backup password and Windows password settings from this menu. Secure Drive Settings: You can open/close, change drive location and change the capacity of the secure drive from this menu.
Modules Data Backup Settings: Use this menu to set the location of the back up data (click Browse and set location), manage the backup password and to select which items are backed up (enrolled fingerprints and online accounts data). Figure 7 - 38 Control Center Data Backup Settings 7 Data Restore Settings: If you need to restore previously backed up data then do so from this menu. Click Browse and go the location of the original backup, and input the password.
Modules Information These menu items provide online information on your software version, support and any new features. You can also access the animated Tutorial on Online Accounts, Swipe One and Secure Drive.
Modules Bluetooth & WLAN Combo Module If your purchase option includes the Combination Wireless LAN & Bluetooth module (either Intel® or 3rd Party) then install the driver as instructed overleaf. Make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver. Bluetooth Data Transfer Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported).
Modules High Speed Bluetooth Data Transfer 7 The Combination Wireless LAN & Bluetooth module supports high speed data transfer. However to achieve such transfer speeds, both devices must support high speed data transfer. To obtain high speed data transfer make sure that both the WLAN and Bluetooth modules are powered on. Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer. 3rd Party Bluetooth (V4.0) Combo Driver Installation 1.
Modules Bluetooth Configuration in Windows 8 You can configure a Bluetooth connection as below, however make sure the Bluetooth module is on (i.e. not in Airplane Mode) before configuration begins. Desktop Mode 1. 2. 3. Switch to the Windows Desktop (click the App or use the Windows logo key D key combination). Click the notification area of the taskbar and double-click the Bluetooth icon click and select Show Bluetooth Devices). The Devices item in PC Settings will appear. OR + (or \ Charms Bar 1. 2.
Modules 4. 5. Click Add a Device. Double-click the device you want to pair with the computer. 6. On first connection the computer will provide you with a pairing code to be entered onto the device. 7. Enter the code into your Bluetooth enabled device and click Yes on the computer to complete the pairing.
Modules 8. You need to either use Airplane Mode, or to turn the Bluetooth module off aboard aircraft.
Modules To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. 4. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination). Click the notification area of the taskbar, click the Bluetooth icon and click Open Settings. Click Options, and make sure that Allow Bluetooth devices to find this computer check box (Discovery) has a tick inside it.
Modules Intel® Rapid Storage Technology The Intel Rapid Storage Technology application provides high-performance SATA and SATA RAID capabilities. Install the Intel Rapid Storage Technology application (after installing all necessary drivers in the correct order) to support your RAID system or SATA drive if set up in AHCI mode in the BIOS (see “SATA Mode (Advanced Menu)” on page 5 - 10). IRST Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2.
Modules Intel® Rapid Storage Technology for RAID Systems Intel® Rapid Storage Technology application displays status information on your RAID configuration. Run the Intel® Rapid Storage Technology application from the item in the Start menu. When the Intel® Rapid Storage Technology application is launched the system will open the Status window. Here you can view the general health of the storage system. Various volume creation and management options are available depending on the system’s status.
Modules Intel® Rapid Storage Technology Help If a hard drive member of a RAID volume is reported as “Degraded” or “Failed” it may be possible to recover the volume. If the volume cannot be restored then you will need to recreate the RAID volume and restore the data from a back up. Click the Help menu (or press F1) for instructions on how to recover or recreate RAID Volumes. Help Click the Help (or press F1) menu button at the top of the Intel® Rapid Storage Technology application.
Modules RAID Volume Data Verification and Repair The RAID volume data verification process identifies any inconsistencies or bad data on a RAID 0 or RAID 1 volume. The table outlines what occurs for each RAID level: Table 7 - 2 RAID Level Verification & Repair Status 7 RAID Level Verify RAID 0 Bad blocks are identified. Verify & Repair N/A Bad blocks are reassigned. Bad blocks are identified. RAID 1 Data on the mirrored drive is compared to data on the source drive.
Modules Verifying and Repairing RAID Volume Data 1. 2. 3. 4. 5. 6. Before verifying the volume data you will need to initialize the volume. Run the Intel® Rapid Storage Technology application. Click to select the RAID in the pane on the right side of the window. Click Manage and click Advanced. Click Initialize and click Yes (button) to begin the process. The completion percentage will be listed under Status.
Modules 7. 8. 7 Click Advanced and click Verify, then click Verify (button) to begin the process. The completion percentage will be listed under Status (verifying and repairing).
Modules Intel® Rapid Start Technology Driver Intel(R) Rapid Start Technology can resume power from Hibernation within 5 to 6 seconds and can remember your computer's previous state with zero power. System Requirements to support Intel® Rapid Start Technology: • Rapid Start Technology should be enabled in the BIOS (see ““Intel(R) Rapid Start Technology (Advanced Menu)” on page 5 - 9). • Intel Rapid Storage Technology software installed. • A Solid State Drive (SSD) with a minimum capacity of 18.6GB.
Modules Intel® Rapid Start Technology Configuration 1. 2. 3. 7 Enable/disable Intel(R) Rapid Start Technology from the BIOS (see “Intel(R) Rapid Start Technology (Advanced Menu)” on page 5 - 9). Go the Windows control panel and double-click Administrative Tools (System and Security)> Computer Management > Storage > Disk Management Right-click the SSD and select Shrink Volume from the menu.
Modules 4. Enter the figure, which should be equal to amount of system memory (RAM) in your computer, in “Enter the amount of space to shrink in MB”. Figure 7 - 50 Shrink Volume Size 7 5. Click Shrink (any unallocated file space may be formatted for storage use). Memory Size (Amount of Space to Shrink) The figure entered in the “Enter the amount of space to shrink in MB” field above should be equal to the amount of system memory in your computer.
Modules 6. Run the Desktop app and right-click the lower left hot corner (or use the Windows Logo Key + X key combination) and select Command Prompt (Admin). 7. 8. Type “DISKPART”. At the DISKPART command type “list disk”.
Modules 9. Type “select disk #” (# is disk number where you want to create the store partition, so refer to the results obtained from "list disk" for exact disk number). 10. The message “Disk # is now the selected disk.” will appear. Figure 7 - 53 Diskpart - Select Disk # 7 11. Type “create partition primary”. 12. A “DiskPart succeeded in creating the specified partition.” message should appear.
Modules 13. Type “detail disk”. Figure 7 - 55 Diskpart - Detail Disk 14. Type “select Volume #” (# is volume of your storage partition so refer to results obtained from "detail disk" for the exact volume number). 15. The message “Volume # is now the selected volume.” will appear.
Modules 16. Type the following, depending on the format of the SSD. • For MBR formatted SSD’s: “set id=84 override” (the id must be set to 84). • For GPT formatted SSD’s: “set id=D3BFE2DE-3DAF-11DF-BA40-E3A556D89593”. Figure 7 - 57 Diskpart - Set id= 7 17. The message “DiskPart successfully set the partition ID.” will appear. 18. Close the CMD window.
Modules 19. Go the Windows control panel and double-click Administrative Tools (System and Security)> Computer Management > Storage > Disk Management. 20. The disk partition should read Healthy Hibernation Partition. Figure 7 - 58 Computer Management (Healthy Hibernation Partition) 7 Healthy (Hibernation Partition) 21. Restart the computer. 22. Install the driver (see below). Intel® Rapid Start Technology Driver Installation 1.
Modules Intel® Wireless Display Application The Intel® Wireless Display Application (requires Intel® Centrino WLAN/ Combo module), in conjunction with a compatible video adapter (purchased separately), allows you to display the contents of the notebook display on another display (e.g. HDTV) without the need to have cables stretching across a room. You can then play games, browse the internet, display videos or photo slide shows on your TV/external display without using HDMI or A/V cables.
Modules Intel® WiDi Application Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 7.Install Intel WiDi AP > Yes. 4. Click Next. 5. Click the button to accept the license and click Next. 6. Click Finish.
Modules Intel® WiDi Application Configuration 1. 2. 3. Run Intel(R) Wireless Display from the Start screen. Click I agree to the terms of this license (button). The application will scan for any connected compatible adapters (or you can click the Scan for available adapters button to enable Intel My WiFi Technology).
Modules 4. 5. 6. Click to select and detected adapters, and click Connect. The system will then prompt you to enter the 4-digit security code which will be displayed on the external TV Screen (or press the connect button on the wireless speaker adapter). Enter the code for the video adapter and click Continue.
Modules 7. 8. You will then be prompted to enter a name for the video adapter and click Continue. Click Finished to complete the setup. Test Audio Adapter To verify a successful audio connection (for Intel® Wireless Music), select the “Test your audio connection” link or select “Finished” to bypass the test. You can select “Play Sample” to play an audio test sample from your adapter to the connected speaker set.
Modules Creative Software AutoUpdate 7 Run the application from the shortcut in the Start screen and make sure you are connected to the internet, then click Next and follow the on screen instructions to update the software. Sound Blaster Cinema EQ Install the Sound Blaster Cinema EQ to allow you to configure the audio settings to your requirements for the best performance in games, music and movies. Sound Blaster Cinema EQ Installation 1.
Modules Sound Blaster Cinema Application Run the Sound Blaster Cinema control panel from the notification area of the taskbar (or from the item in the Start menu). Click on the tabs to access the any of the control panel menus. Power On/Off Sound Blaster Cinema & HDMI Note that the Sound Blaster Cinema audio effects do not apply to audio generated through an HDMI connection.
Modules Sound Blaster Cinema Settings Sound Blaster Cinema selects the built-in speakers by default and this setting may cause some sound quality issues when using headphones. To adjust the settings for headphones do the following: 1. 2. 3. 4. Run the Sound Blaster Cinema application. Select Settings from the menu. Select Headphones from the drop-down menu (you can adjust the slider for crossover frequency). Click OK and close the application.
Modules Sound Blaster Cinema Controls Each control has an On/Off button to allow you to enable/disable the control, and most controls feature a slider to adjust the levels. Settings You can use the drop down menu to use presets for Music, Movie or Games. Alternatively you can use a Custom setting. Menu Figure 7 - 64 Sound Blaster Cinema Controls • • • • Surround: Provides virtual sound channels to control the level of immersion. Crystalizer: Enhances audio to make it sound livelier.
Modules Sound Blaster Cinema & HDMI 1. 2. 3. When you connect an HDMI display to the HDMI-Out port, the Sound Blaster Cinema controls will be disabled. A warning box will pop-up and will prompt “...Do you want to select another audio device now?”. Click No to continue using the HDMI audio output from your external display (do not attempt to select another audio device when connected to the external HDMI display).
Modules 3G Module If you have included an optional UMTS/HSPDA+ based 3G Module (Universal Mobile Telecommunications System or High Speed Packet Access) module (see “Communication” on page D - 4 for specification details) in your purchase option, you do not require a driver/application installation for Windows 8.
Modules Power Safety Warning 7 Before you undertake any installation procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. USIM Card Orientation Note that the USIM card’s readable side (with the gold-colored contacts) should face upwards as illustrated.
Modules 3G Configuration in Windows 8 You can configure a 3G connection as below, however make sure the system is not in Airplane Mode before configuration begins. Charms Bar 1. 2. 3. Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off). A list of available access points will appear.
Modules 4. 5. Any 3G service provider (connection information is usually stored on the USIM card) will appear under Mobile Broadband. Double-click any connection icon under Mobile Broadband (or click and click Connect). Figure 7 - 68 Mobile Broadband (Connect) 7 6. 7. Figure 7 - 69 Mobile Broadband (Disconnect) 7 - 84 3G Module The system will connect to your network.
Modules 8. You can then access the internet, download e-mail etc. as per any internet connection. 9. To disconnect you can select the connection and click Disconnect . 10. You need to either use Airplane Mode, or to turn the Mobile Broadband module off aboard aircraft. Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the system is in Airplane Mode if you are using the computer aboard aircraft.
Modules EM820W 3G Module PIN Code & Power-Saving Note that there may be some issues when a PIN Code is set for the EM820W 3G module (if you are unsure of your module version contact your distributor/supplier) in Windows 8, Mobile Broadband has been turned off, and the system has resumed from a power-saving state. To prevent any issues it is recommended that you simply do not enable a PIN for the EM820W 3G module.
Modules 4. 5. 6. Click Security (tab) and click Disable PIN. Enter the PIN number and click Disable PIN and click OK to confirm. It is recommended that you do not Enable a PIN for the EM820W 3G module.
Modules 7 7 - 88
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power Indicators (see “LED Indicators” on page 1 - 9) to see the computer’s power status. • Connections - Check all the cables to make sure that there are no loose connections anywhere.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Don’t over complicate things. The less you have to deal with then the easier the source of the problem may be found; Example - if your computer has many devices plugged into its ports, and a number of programs running, then it will be difficult to determine the cause of a problem. Try disconnecting all of the devices and restarting the computer with all the peripheral devices unplugged.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator blinking orange. , is Low Battery. Plug in the DC power source.
Troubleshooting Problem The computer feels too hot. Possible Cause - Solution Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 18). Make sure you’re using the correct adapter.
Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Possible Cause - Solution Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work. 8 The system freezes or the screen goes dark. The system’s power saving features have timed-out.
Troubleshooting Problem Possible Cause - Solution The Wireless LAN/Bluetooth modules cannot be configured. The driver(s) for the module(s) have not been installed. Make sure you have installed the driver for the appropriate module (see the instructions for the appropriate module in “Wireless LAN Module” on page 7 - 19 and/or “Bluetooth & WLAN Combo Module” on page 7 - 51). A file cannot be copied connected Bluetooth device.
Troubleshooting Resolving the “Insert a SIM” issue with the 3G Module (Windows 8) 1. If a PIN was set for the EM820W 3G module, you have then switched Mobile broadband off (or put the system in Airplane Mode) under Wireless in PC Settings, and the system has just resumed from a power-saving state the following error may occur. 8 Figure 8 - 1 - PC Settings (Charms Bar) - Wireless (Mobile Broadband Off) 2.
Troubleshooting 3. 4. 5. 6. Go to the Charms Bar. Select Settings and you will then note that the WiFi icon will read Unavailable. Standard procedure would be to click the connection and enter the PIN number to unlock the connection. In this instance you will note that the Mobile broadband connection will read Insert a SIM. 8 Figure 8 - 2 - Mobile Broadband (Insert a SIM) 7. 8. 9. In this case you will need to restart the computer.
Troubleshooting 8 8 - 14
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the ports & jacks which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Ports and Jacks Item Card Reader Description The card reader allows you to use the following digital storage cards: MMC (MultiMedia Card) / RSMMC SD (Secure Digital) / Mini SD / SDHC / SDXC MS (Memory Stick) / MS Pro / MS Duo Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer.
Interface (Ports & Jacks) Item Description HDMI-Out Port The HDMI-Out (High-Definition Multimedia Interface) port is an audio/video connector interface for transmitting uncompressed digital streams. This allows you to connect an external monitor, TV or Flat Panel Display etc. as a display device by means of a HDMI cable. Note that HDMI carries both audio and video signals (see “HDMI Audio Configuration” on page C 35). Headphone-Out Jack Headphones or speakers may be connected through this jack.
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB (Universal Serial Bus) 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Control Center Appendix B: Control Center Overview The following chapter will give a quick description of the functions of the Control Center. The Control Center gives quick access to frequently used controls, power management features and enables you to quickly turn modules on/off. Click the Control Center icons to toggle the appropriate function, or hold the mouse button down and move the slider where applicable. Certain functions will automatically be adjusted when a power mode is selected.
Control Center Power Modes You can set a Power Mode by clicking the appropriate icon at the top of the Control Center. Each power mode will affect screen brightness, Touchpad and PC camera power etc. You can click a Control Center icon to set an overall power mode and then click individual icons in the Control Center to power on/off the Touchpad and PC camera.
Control Center Power Status The Power Status icon will show whether you are currently powered by the battery, or by the AC/DC adapter plugged in to a working power outlet. The power status bar will show the current battery charge state. Brightness The Brightness icon will show the current screen brightness level. You can use the slider to adjust the screen brightness or the Fn + F8/F9 key combinations, or use the Fn+ F2 key combination to turn off the LED backlight (press any key to turn it on again).
Control Center Sleep Click the Sleep button to bring up the Hibernate or Sleep buttons, and click either button to have the computer enter the appropriate power-saving mode (see “Power-Saving States” on page 3 - 6). Display Switch Click the Display Switch button to access the menu (or use the priate attached display mode (see page C - 24). + P key combination) and select the appro- Time Zone Clicking the Time Zone button will access the Date and Time Windows control panel.
Video Driver Controls Appendix C: Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 32. Video Driver Installation Video Card Options Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). Note that card types, specifications and drivers are subject to continual updates and changes.
Video Driver Controls NVIDIA® Optimus™ Technology iGPU or dGPU Most notebook computers come with either a discrete or integrated graphics solution. Note the NVIDIA control panel refers to Highperformance NVIDIA processor (which is the discrete GPU) and Integrated graphics (which is the integrated GPU). Discrete graphics solutions feature a dedicated Graphics Processing Unit (GPU) which are capable of playing games, watching HD video or running GPU-based applications.
Video Driver Controls How Optimus Technology works When the system is powered up and is displaying just the desktop, the dGPU will be powered off. In this case the system is running in the same way as a system without a discrete graphics solution. However when an application that requires use of the dGPU is run (e.g, a game or HD Video), the dGPu is powered on and takes over the processing duties. If the program is closed, then the dGPU will be powered back down again until required.
Video Driver Controls GPU Button This computer also features a button that allows the user to switch between Optimus Mode and UMA Mode (Unified Memory Architecture). UMA Mode will use only the integrated GPU; Optimus Mode will allow the system to automatically determine whether the dGPU or iGPU is used. Thus the user can completely control how the graphics system operates. Press the GPU button, and the button color will indicate the current mode.
Video Driver Controls Intel® Dynamic Video Memory Technology Intel® DVMT automatically and dynamically allocates as much (up to 1748MB) system memory (RAM) as needed to the integrated video system (the video driver must be installed). DVMT returns whatever memory is no longer needed to the operating system.
Video Driver Controls Intel® Graphics & Media Control Panel Advanced video configuration options are provided by the Intel® HD Graphics Control Panel. To access the control panel see below and overleaf: 1. Click the Intel® Graphics and Media Control Panel icon in the Start screen.
Video Driver Controls OR 2. Right-click the Desktop and select Graphics Properties from the menu. OR 3. 4. 5. Click Advanced settings in the Screen Resolution control panel in Windows. Click the Intel(R) HD Graphics Control Panel tab and click Graphics Properties (button). Double-click the Intel(R) HD Graphics control panel in the Windows Control Panel.
Video Driver Controls You may make changes to any of the graphics properties by clicking the appropriate menu panel and adjusting the settings on the right.
Video Driver Controls Sub-Menus Some of the menu panels will also have sub-menus (in the top left corner of the menu alongside the icon ) to display further configuration options.
Video Driver Controls Multiple Display Display Click either Display Settings or Color to make display adjustments, including configuration for any attached external displays. At least one other display must be attached in order to view multiple display selection options.
Video Driver Controls Click the Display menu at the top of the screen to display the sub-menus. The Multiple Displays menu allows you to configure the display mode of any attached displays (see “Attaching Other Displays” on page C - 22). Multiple Display At least one other display must be attached in order to view multiple display selection options.
Video Driver Controls The Audio sub-menu allows you to configure the capability mode of any attached displays if applicable (i.e. the attached display supports audio). Enable Audio Without Video to keep audio on when the display blanks out for power saving purposes.
Video Driver Controls 3D This menu allows you to choose how 3D images are displayed. Quality displays the most detail, Balanced provides better computer performance with good quality and Custom allows you to configure the Anisotropic Filtering, Vertical Sync and Anti-Aliasing features to your preferences. Click Apply to save changes.
Video Driver Controls Options Options allows you to Customize Hot Keys (for opening the application, rotating the display, scaling etc.,) to your preferences. Click Apply to save changes.
Video Driver Controls Click the Options menu at the top of the screen to display the sub-menus. The Information Center provides details on System Information, the Built-In Display and any attached displays. Preferences Go to the Preferences sub-menu in Options to configure the preferences for the Intel® HD Graphics Control Panel. Make sure you turn Tray Icon On to display the Intel® HD Graphics Control Panel icon in the notification area of the taskbar (as below).
Video Driver Controls Video The Video Profiles menu allows you to brighten or darken movies, or to switch to vivid colors. Click Basic or Advanced to adjust the video settings based on the Application Settings or Driver Settings. The Preview image will display a sample image using the current settings. You can Save Profile and name the Profile to recall the settings at any time. Click Apply to save changes.
Video Driver Controls Click the Video menu at the top of the screen to display the sub-menus.The Image Enhancement menu allows you to adjust the Sharpness, Skin Tone Enhancement, Noise Reduction etc.Click Apply to save changes.
Video Driver Controls The Image Scaling and Gamut Mapping menus allow you to adjust these items.
Video Driver Controls Power Choose a Power Plan for when the computer is Plugged in or On battery. When turned on, the Display Power Saving Technology (which adjusts the backlight intensity) battery settings may be adjusted by means of the slider towards Maximum Quality or Maximum Battery. Click on Apply to save changes.
Video Driver Controls Support Click Support and select an item from the menus to bring up the help and support topics. You will need to be connected to the Internet to access the key resource links.
Video Driver Controls Display Devices & Options Note that you can use external displays connected to the HDMI-Out port and/or external monitor port. See your display device manual to see which formats are supported. Attaching Displays When you first attach an external display you may find that the desktop does not occupy the full screen area. Use either the display’s auto adjust/configure controls, or the Intel(R) HD Graphics Control Panel to configure the full screen display.
Video Driver Controls Multiple Display At least one other display must be attached in order to view Multiple Display selection options. Attaching Other Displays To Clone Displays: 1. 2. 3. 4. 5. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Clone from the Select Multiple Display Mode menu. Click Apply, and OK to confirm the settings change.
Video Driver Controls To Enable Extended Mode: 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Extended from the Select Multiple Display Mode menu. Click Apply, and OK to confirm the settings change. Click the appropriate monitor icon and drag it to match the physical arrangement you wish to use (e.g.
Video Driver Controls Windows Logo Key + P Key Combination You can use the +P key combination to quickly bring up the Second Screen menu. Attaching Other Displays - Devices (Charms Bar) You can configure attached displays from Devices (in the Windows 8 Charms Bar). 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go the Charms Bar and select Devices. Click Second Screen.
Video Driver Controls Configuring an External Display In Windows 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go to the Screen resolution control panel (see page 1 - 32) in the Desktop app. Click the Detect button. The computer will then detect any attached displays.
Video Driver Controls 5. You can configure the displays from the Multiple Displays menu. Figure C - 20 Screen Resolution Multiple Display Options C • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) • Extend these displays - Treats both connected displays as separate devices • Show desktop only on 1/2 - Only one of your displays is used.
Video Driver Controls NVIDIA Control Panel More advanced video configuration options are provided in the NVIDIA Control Panel tab. 1. 2. Go to the Control Panel. Double-click NVIDIA Control Panel (click to view the control panel in either Large icons or Small icons if you are in Category view). NVIDIA Control Panel To access the GeForce..... control panel from the desktop; rightclick the desktop, then click NVIDIA Control Panel.
Video Driver Controls Navigating the Control Panel The NVIDIA Control Panel provides additional video configuration controls and tools which allow quick access to features such as image settings, 3D Settings and video configuration. Navigate through the control panels in much the same way as you would a web page. Click on the sub-heading tasks in the left menu (and on the highlighted links) for information. Use the buttons on the top left to go back, forward etc.
Video Driver Controls Optimus™ Customization Options One of the most important aspects of Nvidia® Optimus™ technology is that it will switch between the integrated GPU and discrete GPU seamlessly and automatically, and does not require any input from the user. However customization options are offered for users who prefer to set their own parameters for GPU usage.
Video Driver Controls iGPU or dGPU Note the NVIDIA control panel refers to High-performance NVIDIA processor (which is the discrete GPU) and Integrated graphics (which is the integrated GPU). 3. 4. 5. 6. Close the NVIDIA Control Panel. Find the executable file icon of the application you want to run. Right-click the icon and select Run with graphics processor from the context menu.
Video Driver Controls Global Settings Global settings allows you to set the preferred graphics processor for overall use. Ideally this would be the iGPU for battery life, but this can be set to the dGPU if preferred. 1. 2. 3. 4. 5. Go to the NVIDIA Control Panel (see page C - 27). Click Manage 3D Settings (3D Settings) and select Global Settings (tab). Select either Integrated graphics (iGPU) or High performance NVIDIA Processor (dGPU) from the drop-down menu.
Video Driver Controls Program Settings Program settings allows you to make specific adjustments for installed applications. 1. 2. 3. 4. 5. 6. Run the NVIDIA Control Panel (see page C - 27). Click Manage 3D Settings (3D Settings) and select Program Settings (tab). Select a program to customize from the drop-down menu, or click Add to add any program that does not appear in the menu. Select the preferred graphics processor for the program from the drop-down menu.
Video Driver Controls Set PhysX® Configuration NVIDIA® PhysX® is a physics engine that can use the GPU to accelerate game and 3D application performance. You can select the GeForce video card or CPU as a PhysX® processor, or configure the computer to auto-select a PhysX® processor (recommended default setting). 1. 2. 3. 4. Go to NVIDIA Control Panel (see page C - 27). Click Set PhysX configuration. Click to Select a PhysX processor from the menu; Auto-select (recommended) is the default setting.
Video Driver Controls Video Settings Click the sub-menus under Video to adjust the video color or image settings.
Video Driver Controls HDMI Audio Configuration HDMI (High-Definition Multimedia Interface) carries both audio and video signals. In some cases it will be necessary to go to the Sound control panel and manually configure the HDMI audio output as per the instructions below. 1. 2. 3. 4. Go to the Control Panel.
Video Driver Controls 5. 6. Adjust the HDMI settings from the control panel tabs. Click OK to close the Sound control panel.
Video Driver Controls HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device. • To play audio sources through your external display’s (TV or LCD) speakers you will need to go to the audio configuration control panel on the display and configure the audio input accordingly (see your display device manual). HDMI Video Configuration 1. 2. 3. 4. Connect an HDMI cable from the HDMI-Out port to your external display.
Video Driver Controls C C - 38
Specifications Appendix D: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your distributor/supplier for details.
Specifications Processor Memory Intel® Core i7-4900MQ (2.8GHz) Mobile Processor 8M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 47W Dual Channel DDR3L Intel® Core i7-4800MQ (2.7GHz) Mobile Processor 6M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 47W Intel® Core i7-4700MQ (2.4GHz) Mobile Processor 6M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 47W Core Logic Mobile Intel® HM87 Lynx Point Express Chipset Display Model A: 15.6" (39.
Specifications Keyboard & Pointing Device Card Reader Communication Full Size Isolated Winkey Keyboard with Numeric Keypad Built-In TouchPad (with Multi Gesture Functionality) GPU Mode Button (UMA/Optimus Mode) Embedded Multi-In-1 Push-Push Card Reader - MMC / RSMMC - SD / Mini SD / SDHC / SDXC - MS / MS Pro / MS Duo Built-In 10/100/1000Mb Base-TX Ethernet LAN Model A: One Instant Button for Airplane Mode Model B: Three Instant Buttons for Airplane Mode, Mute & Camera On/Off Note: Some of these cards
Specifications For Model A Only: UMTS/HSPA+ based 3G Module with Full Size Mini-Card Interface (Factory Option) Quad-band GSM/GPRS (850 MHz, 900 MHz, 1800 MHz, 1900 MHz) UMTS WCDMA FDD (2100 MHz) Note that UMTS modes CAN NOT be used in North America BIOS One 48Mb SPI Flash ROM AMI BIOS Security Security (Kensington® Type) Lock Slot BIOS Password For Model A Only: Fingerprint Reader Module (Factory Option) Operating System Windows® 8 D D - 4 Specifications Features Power Management IMR (Injected Molde
