FRANÇAIS 1} Enlever tous les matériaux d’emballage & Inintérêt rieur du four, ainsi que !'étiquette publicitaire de la porte du four. 2) Vérifier que le four n’a pas 6té endommagé pendant le transport. En particulier, s assurer que: a) La porte n'est pas décalée ou fausse. b} Les charnières et logues de sécurité de la 4) porte ne sont pas cassés ou desserrés. ¢) Rejoint de porte et la surface de contact du joint ne sont pas endommagés.
précautions A OBSERVER ) 1) Contrôle d’aspect — Ne pas utiliser ce four s'il présente des signes d’endommagement. Voir la rubrique 2} du chapitre INSTALLATION, page F1. 2) Porte — Ne jamais faire fonctionner le four avec un objet pris entre fe four et la porte. 3) Plateau tournant Avant d’utiliser ie four, vérifier que le support de plateau est bien en place et le plateau tournant bien centré sur son support. 4) Ventilation — Ne kamis obstruer les ouvertures de ventilation du four.
Répartiteur du guide d'ondes Élément chauffant du gri! Support du plateau tournant Porte Trappe d’accès a la lampe Ouvertures de ventilation Plateau tournant Support du plateau tournant . Poser le plateau tournant sur son Cordon d’alimentation support.
W PLATEAU TOURNANT S’utilise dans tous les modes de cuisson. {(En cuisson par CONVECTION, on plats superposés et pour ia cuisson &u Gril. EMBROCHAGE ET MISE EN ' PLACE DE LA BROCHE: Mettre en place le support en céramique (A} sur les appuis {C} contre la paroi gauche du four. 2. Embrocher 'aliment bien au centre de la broche D). Mettre en place les fourches (E) de part et d’autre de I’aliment et bien serrer les vis de blocage (F} des fourches. 3.
Nous présentons ci-après le mode opératoire de base et nous vous renvoyons au Livre de Recettes pour tout ce qui concerne |‘aspect proprement culinaire. Généralités 1. Le four ne doit jamais être utilisé sans le plateau 1 son support. Veillez 2 ne pas bloguer t ot son support qui doivent pouvoir tourner librement. . Vérifiez que le minuteur est en position ¢’ et branchez le four dans une prise murale [courant alternatif 220V seulement). .
RECTION [ Mettez le sélecteur de mode de cuisson en position (CONVECTION]. Réglez la température. Réglez le minuteur sur le temps de cuisson désiré, Appuyez sur la touche de mise en marche & * Le témoin de cuisson par convection s’allume et reste allumé jusqu'a ce que la température intérieure du four atteigne la température de réglage.
ccrvry &l LOUISON L om binée four permet la cuisson combinée, 'utilisation simultanée des résistances chauffantes et des micro-ondes. L aliment étant simultanément doré en surface par la chaleur rayonnante et cuit en profondeur par les micro-ondes, le temps de cuisson est ainsi plus court qu’en procédant par étapes successives. Mettez le sélecteur de mode de cuisson en position {cuisson combinée microsondes et gril}.
Cuisson 2 la ratissoire: &= Ce four est équipé d'un tourne-broche permettant de cuire de délicieux rôtis ou grillades uniformément dorés, comme en plein air avec un barbecue, sans qu’il soit nécessaire de retourner |'aliment. Le tournebroche peut s’utiliser en cuisson au gril cu en cuisson combine {micro-ondes et griffer, 1. Embrochez I'aliment et mettez la broche en place dans le four {cf. page F-4). Refermez la porte du four. 2. Appuyez sur Interrupteur du tourne-broche. 3.
ENTRETIEN ET NETTOYAGE NE PAS UTILISER LES PRODUITS VENDUS DANS LE COMMERCE POUR LE NETTOYAGE DES FOURS CAR CERTAINS SONT TRÈS DÉCAPANTS OU ABRASIFS. LES TAMPONS DE RÉCURAGE RISQUENT DE RAYER ET TERNIR LE TABLEAU DES TOUCHES DE COMMANDES ET LES PEINTURES DU FOUR A MICRO-ONDES. Extérieur du four Nettoyer Extérieur du four au savon doux et & F'eau. Rincer pour éliminer F'eau savonneuse et sécher avec un chiffon doux.
“AVANT D'APPELER LE DÉPANNEUR Avant de faire appui a un dépanneur, commencez par effectuer vous-même les vérifications suivantes: 1. Alimentation Vérifiez que le four est convenablement raccordé a une prise murale. Vérifiez le fusible et le disjoncteur. 2. Ramenez le minuteur en position ‘' ', placez une tasse pleine d’eau dans le four et refermez la porte.