REALITY 9200 TCR+ R9001390 OWNER'S MANUAL
BARCO PROJECTION SYSTEMS REALITY 9200 TCR+ R9001390 OWNER'S MANUAL Date : 020798 Art. No.
Federal communication commission (FCC statement) This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Table of Contents TABLE OF CONTENTS ........................................................................................................................................................................... i-1 UNPACKING AND DIMENSIONS .......................................................................................................................................................... 1-1 Unpacking ..........................................................................................................
Table of Contents Options ........................................................................................................................................................................................ 8-11 INSTALLATION MODE ........................................................................................................................................................................... 9-1 Starting up the Installation Mode ....................................................................
Unpacking and Dimensions 1 UNPACKING AND DIMENSIONS Unpacking To open the banding, pull on the clip as shown in the first drawing. Pull To open Take the projector out of its shipping carton and place it on a table. For transportation, the projector is mounted on a wooden board with 3 bolts. Use a 13 mm wrench to remove these bolts. When using the projector as a table mounted configuration, always mount the 3 supporting feet (see drawing below). These feet are mounted on the same wooden board.
Unpacking and Dimensions Battery installation in the RCU. A battery (not yet installed to save the battery life time) is delivered inside the plastic bag with the power cord. To install the battery, remove the battery cover on the backside of the remote control by pushing the indicated handle a little towards the bottom of the RCU. Lift up the top side of the cover at the same time (fig. 1).
Installation Guidelines 2 INSTALLATION GUIDELINES Installation Guidelines Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system. Max. ambient temperature : 40 °C. Min. ambient temperature : 0 °C. The projector will not operate if ambient air temperature falls outside this range (0°C- 40°C).
Installation Guidelines * Where to install the projector? Inputs and computer video format input compatibility : Definitions of the Abbreviation on drawings Some examples : B = Distance between ceiling and top of the screen or between floor and bottom of the screen. A = Correction value, distance between bottom side of projector (without feet) and middle of the lens. Value to be subtracted from B to obtain the correct installation position.
Location and Functions of Control 3 LOCATION AND FUNCTIONS OF CONTROL Front Panel Terminology 9 0I T h i s d e v i c e co m p l i e s w i t h P a rt 1 5 o f t h e F C C r u l e s .
Location and Functions of Control b. Remote control This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This remote control is used for source selection, control, adaptation and set up. It includes automatic storing of : - picture controls (Brightness, Sharpness...) - settings Other functions of the remote control are : - switching between standby and operational mode.
Installation Set Up 4 INSTALLATION SET UP The projector can be installed to project images in four different configurations : front/table, front/ceiling, rear/table and rear/ceiling. 5HDU &HLOLQJ )URQW &HLOLQJ 5HDU 7DEOH )URQW 7DEOH To change the Configuration, enter the adjustment mode by pushing ADJUST or ENTER. Highlight Installation by pushing the control disc forward or backward and press ENTER to select. The installation menu will be displayed. ENTER displays the Installation menu.
Installation Set Up 4-2 5975938 BARCOREALITY 9200TCR+ 020798
Connections 5 CONNECTIONS AC Power (mains) cord connection Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the front of the projector. The power input is auto-ranging from 200 to 240 VAC. This projector may be connected to an IT-power system. T h i s d e vic e co m p lie s w it h P a r t 1 5 o f th e F C C r u le s .
Connections Lamp Run Time When the total run time of the lamp is 970 hours or more, the following warning message will be displayed for 1 minute. This warning message will be repeated every 30 minutes. Press EXIT to remove the message before the minute is over. When the total run time of the lamp is 1000 hours or more, the following warning message, with the exact run time is displayed on the screen. Lamp run time 980 h Lamp run time is 1000 hours.
Connections Fixed RGB analog input (slot 1) Slot 1 has RGB analog input terminals (BNC) with separate Horizontal and Vertical sync (RGBHV) or with composite sync input (RGBS). PROJECTORMODE : GREEN - OPERATION RED- STANDBY COMMUNICATION PORT RS232 IN RS232 OUT (800-PERIPHERALS) DIAGNOSTICS IR-ACKNOWLEDGED CODE IR-RECEIVER REMOTE SDI IN SDI O UT Always use an interface when a computer and local monitor have to be connected to the projector.
Connections Fixed 5-Input Slot (slot 2) Slot 2 has 5 BNC input terminals.
Connections S-VIDEO On To the Video input : R Composite video signals from a VCR, OFF air signal decoder, etc... 1 x BNC 1.0Vpp ± 3 dB On 9,'(2 6 9,'(2 ,1387 To the S-Video input : S-Video input Separate Y-luma/C-chroma signals for higher quality playback of Super VHS-signals.
Connections RGB Analog Input Module. PROJECTOR MODE : GREEN - OPERATION RED- STANDBY COMMUNICATION PORT RS 232 IN RS232 OUT (800-PERIPHERALS) DIAGNOSTICS IR-ACKNOWLEDGED CODE IR-RECEIVER REMOTE SDI IN SDI OUT IR-RECEIVED R G B V H R G B H/ C V 6 9,'(2 R 9,'(2 G B V H/ C On Always use an interface when a computer and local monitor have to be connected to the projector. See 'slot 1' for interfaces to be applied.
Connections Push the control disc up or down to select Installation and press ENTER. ADJUSTMENT MODE Select a path from below : GUIDED RANDOM ACCESS INSTALLATION SERVICE Use the control disc to select Input Slots by pushing up or down and press ENTER. The internal system will scan the inputs and displays the result in the Input Slots menu. Select with or then to return.
Connections Straps on module level : Floating or non-floating input. R-Y : J3 : strap "yes" : non floating Y: J4 : strap "yes" : non floating B-Y : J5 : strap "yes" : non floating S: J6 : strap "yes" : non floating )ORDWLQJ RU QRQ IORDWLQJ LQSXW Non-Floating strap strap strap strap "no" "no" "no" "no" : : : : floating floating floating floating Floating Factory preset : strap "yes", non floating input Sync selection. J8 : strap "no" : separate sync strap "yes" : sync on Y.
Connections Straps on Module Level : - 6 \ Q F V H OH F WLR Q Floating or non-floating input. Red : J3 : strap "yes" : non Green : J4 : strap "yes" : non Blue : J5 : strap "yes" : non H/C : J6 : strap "yes" : non V: J7 : strap "yes" : non 6 HS D UDW H V \Q F floating floating floating floating floating strap strap strap strap strap "no" "no" "no" "no" "no" : : : : : 6 \Q F R Q J UH HQ floating floating floating floating floating Factory preset : strap "yes", non floating input Sync selection.
Connections Connecting a Computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS 232 input of the projector. PROJECTORMODE : GREEN - OPERATION COMMUNICATION PORT RS 232 IN RS232 OUT (800-PERIPHERALS) RED - STANDBY DIAGNOSTICS IR-ACKNOWLEDGED CODE IR-RECEIVER REMOTE SDI IN SDI OUT IR-RECEIVED R G B H V R G B H/ C V 6 9,'(2 R 9,'(2 G B On Applications : remote control and data communications.
Controlling 6 CONTROLLING The projector can be controlled with a. The RCU b. The hardwired RCU (cable is not included) c. The local keypad. c) Point the front of the RCU directly at one of the IR sensors of the projector. IR sensor IR sensor Controlling the projector with the RCU and the hardwired RCU is equal. How to Use the RCU? 0I 9 T hi s d ev ic e c om pl i es w it h P ar t 1 5 of t he F C C r ul es .
Controlling How to Display a Projector Address? Press the ADDRESS key (recessed key on the RCU) with a pencil. The projector's address will be displayed in a 'Text box'. This text box disappears after a few seconds. To continue using the RCU, it is necessary to enter the same address with the digit buttons (address between 0 and 9). For example : if the Address key displays projector address 003, then press "3" digit button on the RCU to set the RCU's address to match the projector's address.
Start up of the Adjustment Mode 7 START UP OF THE ADJUSTMENT MODE Adjustment Mode All source parameters, picture tuning and geometry are made while in the 'Adjustment Mode' . Press the ADJUST or ENTER key to enter the 'Adjustment mode'. You are now in the 'Adjustment Mode'. The control disk (RCU) or '+ or '-' keys (local keypad) are used to make menu selections and also for adjustments. The ENTER and EXIT keys are used to move forward and backward through the menu structure.
Start up of the Adjustment Mode 7-2 5975109 BARCOREALITY 9200TCR+ 020798
Random Access Adjustment Mode 8 RANDOM ACCESS ADJUSTMENT MODE Starting up the Random Access Adjustment Mode ADJUSTMENT MODE Push the control disc up or down to highlight 'Random Access' and then press ENTER. Select a path from below : LOAD RANDOM ACCESS INSTALLATION SERVICE EDIT Source 01 Select with or then to return.
Random Access Adjustment Mode Highlight File Service by pushing the control disc up or down and press ENTER to select. The File service menu will be displayed. ENTER displays the File Service menu; EXIT returns to the Path selection menu. ADJUST returns to operational mode. The following file manupulations are possible : - Load : installation of a file for a new source. - Edit : editing a loaded file to the source specs. - Rename : renaming a file. - Copy : copying a file to a new file.
Random Access Adjustment Mode The file name will be displayed in the upper right corner.
Random Access Adjustment Mode Options Source Number : The source number of a non-active source can be changed to any other source number. This makes it possible to create a file for future source numbers. EDIT FILE OPTIONS Source number 1 Clamp position [leading] Clamp delay 0 Clamp width 10 Field polarity [pos] Field select [both] Vertical refresh [sync] Vert. sync polarity [leading] Clamp Position : Clamping determines the black level of the signal.
Random Access Adjustment Mode Rename To change the name of a selected file. Use the control disc to select RENAME and press ENTER. The Rename selection menu will be displayed. Use the control disc to select a file name and press ENTER to select. The Rename menu will be displayed with the selected file name already filled in, leave in the 'From file name :' area and in the 'To file name :' area. FILE SERVICE LOAD EDIT RENAME COPY DELETE Select with or RENAME FILE then to return.
Random Access Adjustment Mode Delete To delete a selected file out of the list of files. Use the control disc to select DELETE and press ENTER. The delete selection menu will be displayed. Push the control disc up or down to select a file and press ENTER. If [All] is selected, your password has to be entered before all files will be deleted. FILE SERVICE LOAD EDIT RENAME COPY DELETE OPTIONS Select with or then to return.
Random Access Adjustment Mode CTI ON/OFF CTI : Color Transient Improvement. To improve the transition from one color to another. Highlight CTI by pushing the control disc up or down and press ENTER to toggle between ON and OFF. This function applies to PAL and NTSC video or S-video inputs only. PICTURE TUNING CTI [ON] STILL VIDEO [ON] COLOR TEMPERATURE GAMMA DECODING [EBU] DYNAMIC COLOR DEPTH NOISE REDUCTION EDGE ENHANCEMENT Select with or then to return.
Random Access Adjustment Mode Gamma With the gamma correction adjustment, it is possible to accurately set the gamma of the projector image. To change the gamma value, highlight Gamma by pushing the control disc up or down and press ENTER. PICTURE TUNING SYNC [SLOW] STILL VIDEO [ON] COLOR TEMPERATURE GAMMA DECODING [EBU] GAMMA = 2.2 3 Decoding EBU/IRE Only for NTSC signals. The possibility is offered to decode the NTSC video signals via the default American IRE standard or via the European EBU standard.
Random Access Adjustment Mode Edge Enhancement Increases edge sharpness on all video and data sources. Highlight Edge enhancement by pushing the control disc up or down and press ENTER to select. OFF : off MIN : half normal setting MED : normal setting MAX : 1.5 times normal setting PICTURE TUNING CTI [ON] STILL VIDEO [ON] COLOR TEMPERATURE GAMMA DECODING [EBU] DYNAMIC COLOR DEPTH NOISE REDUCTION EDGE ENHANCEMENT Select with or then to return.
Random Access Adjustment Mode Size GEOMETRY Highlight Size by pushing the control disc up or down and press ENTER to select. SHIFT SIZE SIDE KEYSTONE BLANKING OPTIONS The size can be adjusted in a vertical or horizontal way. When adjusting the vertical size, The upper side of the image is fixed (table and ceiling mounted configurations) and only the lower side can be moved to its exact position.
Random Access Adjustment Mode Blanking Highlight Blanking by pushing the control disc up or down and press ENTER to select. Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information (or noise). A '0' on the bar scale indicates no blanking. GEOMETRY SHIFT SIZE SIDE KEYSTONE BLANKING OPTIONS Select with or then to return.
Random Access Adjustment Mode 8-12 5975938 BARCOREALITY 9200TCR+ 020798
Installation Mode 9 INSTALLATION MODE Starting up the Installation Mode Push the control disc up or down to highlight Installation and then press ENTER. ENTER continues to the Installation mode selection menu. EXIT returns to operational mode. The following item can be selected in the Installation mode : ADJUSTMENT MODE Select a path from below : RANDOM ACCESS INSTALLATION SERVICE Source 01 Input slots : to set up the input priority.
Installation Mode 800 Peripheral When a RCVDS05 is connected to the projector, the type of output module of this RCVDS05 has to be defined in the 800 peripheral menu. The type of output module can be : - standard output module or - 5 cable output module. To define the output module, highlight "800 Peripheral" by pushing the control disc up or down and press ENTER to display the 800 peripheral menu. Use the ENTER key to toggle between [standard] and [5 cable].
Installation Mode Green to Midposition Only in case all panels have been removed and replaced by others or when the convergence is totally misaligned. For normal convergence adjustment, this step can be skipped. To set Green in Midposition, highlight 'Green to midposition' by pushing the control disc up or down and press ENTER to select.
Installation Mode Red on Green convergence 1 Highlight 'Red on Green' by pushing the Control disc up or down and press ENTER to display the Red on green test pattern. The drawings and digit will be displayed in red. 2 Adjust position 1, 2 and 3 to obtain an optimal focus for these lines. 3 Due to interaction, it will be necessary to repeat step 2. CONVERGENCE GREEN TO MIDPOSITION GREEN BLUE ON GREEN RED ON GREEN HATCH ABOUT MOCA Select with or then to return.
Installation Mode Configuration Highlight "Configuration" by pushing the control disc up or down and press ENTER to select. INSTALLATION INPUT SLOTS 800 PERIPHERALS CONVERGENCE CONFIGURATION OSD COLOR NO SIGNAL [BLACK] INTERNAL PATTERNS For more information, see Projector configuration in chapter 4 : 'Installation Set Up'. Select with or then to return. OSD color (On-Screen Display) The highlighted items on the menus can be displayed in red, green or yellow.
Installation Mode 9-6 5975938 BARCOREALITY 9200TCR+ 020798
Service Mode 10 SERVICE MODE Starting up the Service Mode ADJUSTMENT MODE Push the control disc up or down to highlight Service and then press ENTER. Select a path from below : RANDOM ACCESS INSTALLATION SERVICE Some items in the Service mode are password protected (when the password function is active). Enter your password to continue. All other password protected items are now available if you stay in the adjustment mode. Select with or then to return.
Service Mode SERVICE PANEL ADJUSTMENT PRESET INPUT BALANCE IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY LAMP DRIVE MODE MORE... Select the color temperature WHITE BALANCE BLACK BALANCE Select with or then to return. PROJECTOR WHITE 6500 Select with or then to return.
Service Mode Change Password This item is password protected when the password strap is installed. Loosen the locking screws. How to enable or disable the password function ? The password function is enabled when the password strap on the controller module is installed. T h is d e v ic e c o m p l ie s w it h P a r t 1 5 o f th e F C C r u le s .
Service Mode SERVICE IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY Select with or then to return. Select with or then to return. Change Projector Address Change Language Every projector requires an individual address between 0 and 255. Highlight Language by software pushing the control disc up or down and press This address can be installed. ENTER to select the Language Selection menu.
Service Mode Lamp Run Time History To get an overview of the different lamp run times, highlight Lamp Run Time History by pushing the control disc up or down and press ENTER. A listing with the lamp serial number and the corresponding run time will be displayed. The actual installed lamp will be marked. Press EXIT to return to the service mode selection menu. SERVICE IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ.
Service Mode Panel Adjustments Changing these settings may seriously affect the performance of the projector. All panel adjustments are factory adjusted. If not really necessary, do not touch any of these adjustments. They are useful when a new panel is installed. SERVICE BARCO LOGO PANEL ADJUSTMENTS PRESET INPUT BALANCE I2C DIAGNOSIS MORE...
Appendix A : Standard Source Set Up Files A STANDARD SOURCE SET UP FILES NAME RESOLUTION FVERT FHOR FPIX Hz kHz MHz PTOT PACT LTOT LACT 1600-48V 1600 X 600 48,040 62,500 135,000 2160 1600 651 1600-60V 1600 X 1200 60,000 75,000 162,000 2160 1600 1250 1200 1600-65V 1600 X 1200 65,000 81,250 175,500 2160 1600 1250 1200 1600-70V 1600 X 1200 70,000 87,500 189,000 2160 1600 1250 1200 8514-A 1024 X 384I 43,479 35,522 44,900 1264 1024 409 384 CGA 640 X 200 59,924 15,700 14,318 9
Appendix A : Standard Source Set Up Files A-2 NAME RESOLUTION FVERT FHOR FPIX Hz kHz MHz PAM500 640 X 400 PAM800 PTOT PACT LTOT LACT 60,000 26,400 22,810 864 840 440 400 1120 X 375I 89,872 36,443 50,000 1372 1120 406 375 PC98_1 640 X 400 56,416 24,823 21,050 848 640 440 400 PC98_2 1120 X 375I 79,987 32,835 47,840 1457 1120 411 375 PC98_3 1120 X 750 60,000 50,000 78,569 1571 1120 833 750 S1152_66 1152 X 900 66,004 61,846 94,500 1528 1152 937 900 S1152_76 1152 X 90
Lenses B LENSES Focusing the lens Lens holder Fastener ring Loosen the fastener ring of the lens by turning counter clockwise. Focus the image by turning the lens barrel to the left or the right. Attention : Do not turn out the lens too far, otherwise it will fall out of the lens holder. Lens When the image is focused, secure the correct position of the lens with the fastener ring by turning this ring clockwise. Lens Cleaning Procedure Cleaning procedure for HD(1.5-3:1) lens.
Lenses Lenses N ame Len gth len s mm (in ch ) diam. len s mm (in ch ) w eigh t kg (lbs) order n u mber QHD (1.2:1) 253 (9.96) 189 (7.44) 8.7 (19.2) R9829760 HD (2.2:1) 235 (9.25) 137 (5.39) 7.5 (16.5) R9829060 HD (3.3:1) 149 (5.87) 152 (5.98) 4.3 (9.5) R9829075 HD (4.0:1) 165 (6.50) 152 (5.98) 3.5 (7.7) R9829145 HD (5:1) 238 (9.37) 164 (6.46) 5.1 (11.2) R9829180 HD (7:1) 373 (14.68) 196 (7.72) 12.0 (26.4) R9829090 QHD (1.5-3:1) 460 (18.11) 260 (10.24) 13.0 (28.
Source Numbers 80 - 89 and 90 - 99 C SOURCE NUMBERS 80 - 89 AND 90 - 99 Projector without any 800 peripheral connected. The source numbers 80 - 89 and 90 - 99 do not correspond to physical inputs. An additional adjustment file can be created for these source numbers. This file can contain different settings. The relationship between sources 0 - 9 and 90 - 99 or between 0 - 9 and 80 - 89 is shown in the diagram below.
Source Numbers 80 - 89 and 90 - 99 Source numbers 81 - 85 Only valid if no input module is connected to slot 81 - 85 of a RCVDS05. The source numbers 81 - 85 correspond to the physical inputs 1 - 5 of the projector. e.g. When slot 1 of the projector has to be selected, key in source number 81. The relationship between the sources of slot 1 - 5 of the projector with 800 peripheral is shown in the table below.
5&8 5&8 ,1 3 8 7 62 8 5 & (6 ,1 3 8 7 62 8 5 &(6 352-(&725 ,1387 62 8 5&(6 5975938 BARCOREALITY 9200TCR+ 020798 5&9'6 352-(&725 3 3 ,1387 62 8 5&(6 5&9'6