User Manual Software version F1 D13356.
Table Of Contents User Manual .............................................................................................................................. 1 Trademarks and Copyright ........................................................................................................ 1 Environmental Issues ................................................................................................................ 2 Operator Safety Summary..............................................................
Table Of Contents 3.12.5 Assign Floor and Release Floor from Participant ............................................... 51 3.12.4 Chair Control ....................................................................................................... 50 3.12.6 View Site and End View ...................................................................................... 51 3.12.7 Disconnect Participant......................................................................................... 51 3.12.
TANDBERG 770_880_990MXP User Manual 4.5.6 Alert Tones and Volume........................................................................................ 85 4.6 Video .............................................................................................................................. 86 4.6.1 Camera Tracking Mode......................................................................................... 86 4.6.2 MCU Status Line ..........................................................................
Trademarks and Copyright All rights reserved. This document contains information that is proprietary to TANDBERG. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, electronically, mechanically, by photocopying, or otherwise, without the prior written permission of TANDBERG. Nationally and internationally recognized trademarks and tradenames are the property of their respective holders and are hereby acknowledged.
TANDBERG 770_880_990MXP User Manual Environmental Issues Thank you for buying a product, which contributes to a reduction in pollution, and thereby helps save the environment. Our products reduce the need for travel and transport and thereby reduce pollution. Our products have either none or few consumable parts (chemicals, toner, gas, paper). Our products are low energy consuming products.
User Manual Operator Safety Summary For your protection, please read these safety instructions completely before operating the equipment and keep this manual for future reference. The information in this summary is intended for operators. Carefully observe all warnings, precautions and instructions both on the apparatus and in the operating instructions.
TANDBERG 770_880_990MXP User Manual Servicing - Do not attempt to service the apparatus yourself as opening or removing covers may expose you to dangerous voltages or other hazards, and will void the warranty. Refer all servicing to qualified service personnel.
1 Introduction The TANDBERG 770/880/990 MXP system offers superior audio and video quality in a fully featured unit. MXP stands for Media Experience and indicates the new TANDBERG platform. Main Features: Supports videoconferencing via both IP and ISDN networks. Selection of up to 2 Mbps call quality per call, and up to 2,3 Mbps for a MultiSite call totally. Built-in MultiSite *: A maximum of 4 sites + 3 additional telephone calls can participate in joint meetings.
TANDBERG 770_880_990MXP User Manual 1.1 At a Glance Camera The built-in camera includes a high quality colour camera with a fast pan/tilt/zoom action. The camera is controlled by the system’s infra-red remote control and operates pan/tilt, focus and zoom. Codec The Codec is the heart of the system. The main task for the Codec is the compression of outgoing video, audio and data, the transmission of this information to a remote site and the decompression of the incoming information. Hence the name Codec.
1 Introduction Table microphone The high quality table microphone is designed to use on a table during a videoconference. You can connect up to three microphones. The ideal location for the microphone is on a flat surface at least 2m (6.5 ft) from the front of the system. The microphone cable should always point towards the system. The system will automatically equalize sound levels. Loud and soft voices are picked up and transmitted to the far end at approximately the same level.
TANDBERG 770_880_990MXP User Manual 1.2 Menu Structure The menu structure is divided in two. The Main Menu is available for all users and contains all functionality of the system. The Administrator Menu contains all the settings of the system. Enter Administrator Settings from Main Menu - Control Panel. Making changes to the Administrator Settings will change the behavior of the system. The menu structure for Main Menu and Administrator Settings is shown below.
1 Introduction 9
2 Installation Precautions: Never install communication wiring during a lightning storm. Never install jacks for communication cables in wet locations unless the jack is specifically designed for wet locations. Never touch uninstalled communication wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying communication lines. Avoid using communication equipment (other than a cordless type) during an electrical storm.
2 Installation 2.1 Unpacking and Mounting Unpacking The TANDBERG 7700/ 8800/990 MXP consists of the following items: Videoconferencing system with built-in camera Table Microphone Remote Control Batteries User Manual on CD Cables Place the system centrally, on top of the monitor, close to the front and ensure it is stable.
TANDBERG 770_880_990MXP User Manual 2.
2 Installation 1. Microphone cable Connect the microphone to the microphone cable. Connect the microphone cable to microphone input 1 on the system. 2. Monitor cable(s) Scart (Europe): Connect the Scart adapter to one of the Scart connectors on your monitor.
TANDBERG 770_880_990MXP User Manual Note! Make sure you insert the card in the right direction (with the product logo pointing upwards). Push the card into the slot until the Eject button pops up. See chapter 4.8.2.4 Wireless LAN Settings for configuration.
2 Installation 2.3 Monitor Configuration Power on Power on the monitor and use the monitor remote control to select the Audio/Video input used (refer to your monitor manual). If you are using S-video from the system, remember to select S-Video input to avoid a black and white picture. Select Audio/Video input on monitor Selection of Audio/Video input used is generally performed by pressing the 0/AV button on the TV remote control several times.
TANDBERG 770_880_990MXP User Manual 2.4 System Configuration The system must be configured for each installation. Configuration settings can be made via the system menu. Navigate through the menu system using the arrow keys and OK. Remember to press the Save button on the bottom of each menu to save your changes. Press Cancel (x) to return to the previous Menu. See next section for more information about how to use the menus and the remote control. General configuration: 1.
2 Installation 6. Screen Settings When using wide screen (16:9) monitors, set TV Monitor Format to Wide (16:9). TANDBERG also recommends setting Picture Layout to Picture outside Picture when using 16:9 monitors. Picture outside Picture provides a display layout optimized for wide screen monitors. The display layout may be changed at any time using the Layout button on the remote control. 7.
3 General Use Wake up the system When the system is not in use, it is in standby mode and the screens are black. Wake up the system by picking up the remote control. An incoming call or pressing any key on the remote will also wake up the system. If the system does not respond: Make sure that the system is switched on by using the On/Off switch located at the rear of the Codec (see figure below). Verify that your monitor is switched on.
3 General Use 3.1 The Welcome Screen When the system is switched on, you will see the welcome screen. The welcome screen presents the Main Menu and displays your Main Camera image in the background (Main Camera is system default). Your dial in numbers and system name are displayed in the upper right corner. Your ISDN Number and IP Number are the numbers that your contacts need to place a video call to you.
TANDBERG 770_880_990MXP User Manual 3.2 Using the Remote Control The system is controlled with a remote control. Think of the remote control as a mobile phone with number keys and call keys. Use the arrow keys and OK to navigate the menu. The system’s most commonly used functions are also accessible directly from the remote control. The Infra Red (IR) sensor for the remote control is located in front of the WAVE II Camera.
3 General Use 3.2.1 Navigation Arrow keys and OK Navigate in the menu with arrow keys. The yellow selector on screen shows the selected item. Press OK to select. Cancel key In the main menu, pressing Cancel (X) will hide the menu. If the menu is hidden, bring it back with OK. In other menus, pressing Cancel (X) takes you one step back. In an input field, pressing Cancel (X) will delete characters/numbers to the left. Back/Cancel button The X button in the menu corresponds with the X key on the remote.
TANDBERG 770_880_990MXP User Manual How to use Layout with Picture in Picture: 1. 2. 3. 4. Press Layout once to bring up a picture in picture. Press Layout three more times to move it around in the corners of the screen. The fourth time you press Layout, it will disappear. Pressing and holding Layout for 1 second will hide the small picture directly from any position. Example of PIP 3.2.3.
3 General Use Example of Side by Side 3.2.4 Mic Off To mute your microphone during a call, press Mic off. An on-screen indicator appears when the microphone is off. In a call, if audio is detected, the on-screen symbol will start to flash. Pressing Mic off one more time will activate the microphone again. Mic off will mute microphone inputs, but will not mute audio from the AUX and VCR inputs.
TANDBERG 770_880_990MXP User Manual 3.2.6 Number and Letter keys Pressing a number key when you are outside a call will take you to the call menu. When you are in a call, the number keys are used for Camera Presets. Press a number and you go to the corresponding Camera Preset (see chapter 3.10.3 Camera Presets). However, when you are in an input field where numbers are required, the system automatically goes to number mode and you can dial numbers with the number keys as usual.
3 General Use 3.3 On Screen Indicators The system has a number of icons signaling different settings: Volume Off This indicator is shown when the volume is turned off. Press Volume + to turn the volume back on. Microphone Off This indicator is shown when the microphone is turned off. The indicator will start to flash if audio is detected in the room during a call and the microphone is turned off. Press the Mic off button again to turn the microphone back on.
TANDBERG 770_880_990MXP User Manual 3.4 Using the Menu Main menu outside a call and in a call. The menu is the Interface you will use to control the system. The main menu contains: Make a Call, Standby, Phone Book, Move Camera, Presentation, MultiSite Services and Control Panel. When you are in a call, Add another Call and End Call will be available via the green and red buttons. (See pictures below) The menu automatically times out after 15 seconds (see chapter 4.2.1 Menu timeout).
3 General Use 3.5 Make a Call To make a call, choose Make a Call from the main menu. If you are already in a call, choose Add another Call from the main menu to call another participant (if your system has MultiSite capabilities). Pressing the green key on the remote has the same effect as pressing the green button in the menu. You can enter a number manually in the input field or select the book icon to select a contact from the phone book.
TANDBERG 770_880_990MXP User Manual 3.5.2 Telephone Call The TANDBERG system has great audio- as well as video performance. Use the system both as a videophone and a telephone! How to make a telephone call: 1. Press the green key on the remote or choose Make a Call from the Main Menu to open the Call menu. 2. Dial a telephone number with the number keys. 3. Move the yellow selector down to the Place Telephone Call icon and press OK to start the telephone call.
3 General Use 2. Choose Add Video Call or Add Telephone Call from the menu line. An extra number field appears. Press the Add button until you have the desired number of participants (press Cancel inside an empty input field to delete the field). 3. Dial Numbers with the number keys. 4. Press Make Video Call to start the videoconference. If you have a mixed conference with both video and telephone participants, press Make Video Call.
TANDBERG 770_880_990MXP User Manual Call Type Call Type can be set to Video Call (default) or Telephone Call. Using Video, the system will try to connect as a video call. Some network configurations will cause the fallback to a telephone call to fail. In these cases, you should set the call type to telephone and the call will be placed as a telephone type only. For MultiSite calls, Call Type enables you to specify both telephone calls and video calls in the same conference.
3 General Use Type of calls* Auto: Max: 384 kbps on ISDN/768 kbps on LAN 512 kbps on ISDN-BRI 2Mbps (1920 kbps, IP only) 1472 kbps = 23B, IP only 1152 kbps = 18B, IP only 768 kbps = 12B, IP only 512 kbps = 8B 384 kbps = 6B 320 kbps = 5B 256 kbps = 4B 192 kbps = 3B 128 kbps = 2B, Bonding/H.221 64 kbps = 1B, H.221 *Some software versions and networks do not support all channel selections. H.221 or 2x64 (2x56) Calling Some older or low end video systems do not have the ability to make bonded ISDN calls.
TANDBERG 770_880_990MXP User Manual 3.6 Answer an incoming Call You can receive calls anytime, even when the system is in standby mode. But remember to switch the system on using the On/Off switch located at the rear of the system as described in chapter 3 General Use. How to answer an incoming call: 1. To accept an incoming call, press OK or the green key on the remote control. 2. Press the red key on the remote control to reject the incoming call. 3.
3 General Use 3.7 End Call The remote control works much like a mobile/cellular phone. Press End Call from the main menu or the red key on the remote control. In the End Call dialog box, press End Call again. Press Cancel (x) to continue the call. How to end a call: 1. Press the red key on the remote control or End Call from the main menu. 2. Press the red key on the remote control again or OK to confirm that you want to end the call. How to end a multipoint call: 1.
TANDBERG 770_880_990MXP User Manual 3.8 Standby The system will automatically go to Standby mode when it is not in use. You can also choose Standby from the main menu (outside a call) to put the system to standby. In standby mode, the screen(s) are black. It is however still possible to receive incoming calls. The monitors should always remain powered on and the stand-by mode of the system should be used if the system is to be left idle.
3 General Use 3.9 Phone Book The local Phone Book stores up to 200 contacts including the last numbers dialed. Using the Phone Book is time saving and makes sure you do not inadvertently call the wrong number. The contacts are sorted alphabetically. Navigate the phone book with arrow keys or letter keys, searching on the first letter (like on a mobile/cellular phone). Press arrow to the left to select a button. You will see that the last selected contact will be marked.
TANDBERG 770_880_990MXP User Manual 3.9.1 Global Phone Book If your system is connected to an external management system like the TANDBERG Management Suite (TMS), it is possible to use a central contact list from the management system. These contacts can not be changed locally by the system, only from the management system. If you need to modify a number before dialing it, you can do so by hitting ok after selecting the entry, and modifying the number before placing the call.
3 General Use 3.9.3 MultiSite (optional feature) It is possible to pre-define MultiSite meetings using the phone book. You can have up to 6 video participants (including yourself) and 5 telephone participants in a meeting. All sites will then be connected automatically instead of having to add sites one by one. You can store up to 50 MultiSites in the phone book. MultiSite entries consist of contacts that are already stored in the phone book.
TANDBERG 770_880_990MXP User Manual 3.9.4 Edit To edit a contact, highlight the contact and press arrow left. Press arrow key down to select the Edit button. In the edit window you can edit Name, Call Type, Number, Network, Bandwidth and Restrict (56k). Press OK to save. When you edit a contact that is part of a MultiSite entry, the contact will be updated in the MultiSite entry automatically. 3.9.5 Delete To delete a contact, highlight the contact and press arrow left.
3 General Use 3.10 Move Camera There are several ways to move the camera: Choose Move Camera from the main menu. Use the arrow keys to pan and tilt the camera. Press OK when done. When the menu is hidden, the arrow keys will work on the camera. Hide the menu with the Cancel (X) key and adjust the camera with the arrow keys. Use Camera Presets. Press a number and the camera will move to a predefined position (when you are in a call). See chapter 3.10.3 Camera Presets.
TANDBERG 770_880_990MXP User Manual Example: You cannot see what the far end is writing on their whiteboard. Choose Move Camera from the main menu. Choose Far End from the dialog box. Use Zoom and arrow keys to move the far end camera. Press OK when done to go back to normal. See also 3.13.3 Far End Control for more about Far End Control functionality. 3.10.3 Camera Presets Use Camera Presets to easily vary between specific camera positions.
3 General Use Saving Presets for the TANDBERG Tracker: (see separate TANDBERG Tracker instructions included with the tracker): 1. Select which Camera Preset to be used on the TANDBERG Tracker. 2. Move the camera to the position you want to save on the tracker. 3. Save Camera Presets 10-14 from the Save Camera Preset menu (as described in 3 above). It is not possible to save presets 10-14 directly from the remote control. 4. Press the single button on the tracker to activate the Camera Preset.
TANDBERG 770_880_990MXP User Manual 3.11 Presentation The Presentation Functionality in the system enables you to show PC, Document Camera, VCR, AUX and VNC in addition to your Main Camera. This is perfect for meetings where you would like to show a PowerPoint presentation for instance. You can even use arrow keys up and down on the remote control to activate Page Up/Down on the PC (this only applies when using VNC).
3 General Use 3.11.2 Presentation Menu The Presentation menu offers you all available video sources; Main Camera, PC, Document Camera, VCR, AUX and VNC. All these sources can be used as Main Video or Presentation (Duo Video). Press the Main Video button to change Main Video, press the Presentation button to choose Presentation Video. How to change your main video source: 1. Choose Main Video from the Presentation menu. 2. In the Main Video dialog box, choose your desired video source and press OK.
TANDBERG 770_880_990MXP User Manual How to stop a Presentation (Duo Video): 1. Choose Stop Presentation from the Presentation menu. 2. Press OK to stop the presentation. 3.11.3 PC Presenter (DVI/XGA Input) (Optional feature) Users often have their presentations on a laptop that is brought into the meeting room. Remember to connect your PC to the codec before you press the Presentation button.
3 General Use VGA-formats supported on 'DVI-I in'. (VESA compliant) SVGA 800X600 60,72,75,85 Hz XGA 1024X768 60,70,75 Hz SXGA 1280x1024 60Hz 3.11.4 PC Soft Presenter and VNC (Optional feature) PC SoftPresenter is used to display PC images on your system without using a VGA cable (PC Presenter). The system and your PC must be connected to the same LAN. In addition, VNC (Virtual Network Computing) server software must be installed on the PC. Free software can be downloaded from http://www.realvnc.com.
TANDBERG 770_880_990MXP User Manual 3.11.5 Duo VideoTF/H.239 (Optional feature) With Duo Video you have the opportunity to show two different live video streams simultaneously, main video and Duo Video. This is handy when showing a presentation. You see the live presentation and the live video of the presenter simultaneously. When you start a presentation, Duo Video starts automatically if both local and remote system supports Duo Video.
3 General Use 3.11.6 Take New Snapshot The system can take a snapshot of your live video. Snapshot is handy when you are in a call with a system that does not support Duo Video. Use Snapshot to show a snapshot of your presentation and continue the meeting with main camera. How to use snapshot: You find Take New Snapshot in the Presentation menu. Press OK to take a snapshot. Snapshot is found on the Star key on the remote control.
TANDBERG 770_880_990MXP User Manual 3.12 MultiSite Services A Multipoint Control Unit (MCU) enables several sites to participate in the same conference. See chapter 3.5.3 Add Call for how to make a MultiSite call. In TANDBERG's embedded MCU, MultiSite, you can have a maximum of 4 video- and 3 telephone-participants including yourself (the host). The participants are tiled up on the screen and are on display simultaneously in a Split Screen.
3 General Use View Participant/End View Chair Control If you take Chair control, you get the following services: Release Chair Assign Floor To Participant/Release Floor From Participant Disconnect Participant Terminate Meeting Using an external MCU that does not support Chair Control With an external MCU that does not support H.243, you have the following services: Request/Release Floor Terminal Names 3.12.
TANDBERG 770_880_990MXP User Manual Continuous Presence layout 4 split Advanced continuous Precense Layout (3+1) Voice Switched mode 3.12.3 Terminal Names Choose Terminal Names to see a list of the participants of the mulitpoint conference. Press Cancel to go back. 3.12.4 Chair Control (Not supported by TANDBERG MCU or MultiSite) As chairman, you have access to more MultiSite Services. Select Chair Control to assume the role of chairman of the conference.
3 General Use 3.12.5 Assign Floor and Release Floor from Participant Assign Floor allows the chairman to select which of the conference participants that is to be broadcasted to all other participants. 3.12.6 View Site and End View (Not supported by TANDBERG MCU or MultiSite) View Site allows you to view any participant in the conference regardless of whom having floor and chair. Choose End View to go back to normal. 3.12.
TANDBERG 770_880_990MXP User Manual The MultiSite has specific numbers for each call that participates in the conference. To find the dial-in numbers for the MultiSite, choose Information from the main menu and open System Information from the bottom menu line. Site 2 must dial MultiSite Number 2. Site 3 must dial MultiSite Number 3. Site 4 must dial MultiSite Number 4. And so forth Receiving calls to a MultiSite When the MultiSite receives incoming calls you can accept or reject it.
3 General Use By connecting MultiSite systems together, it is possible to connect even more sites in a cascaded MultiSite (see example below). All connections can use any combination of ISDN/IP. The host can connect up to 5 other video systems with MultiSite functionality. The cascaded systems can connect to 4 other video sites. These systems will automatically run Voice Switched mode and transmit a full screen image to the host. In this case you get 20 participants in the cascaded MultiSite conference.
TANDBERG 770_880_990MXP User Manual 3.13 Control Panel The Control Panel contains the features: User Guide Streaming Far End Control Camera Preset Camera Tracking Text Chat System Information Administrator Settings Restart 3.13.1 User Guide The on screen user guide takes you through a quick step-by-step introduction to videoconferencing. It gives the user basic skills in how to use the system.
3 General Use 3.13.2 Streaming Streaming lets you broadcast your meeting to participants on web. The web participants can listen to the meeting, see snapshots, but not participate themselves. Snapshots of current stream (if MultiSite), selfview, far end and DuoVideo streams are accessible via http. See Appendix 6 for descriptions of the possible snapshot files. How to use Streaming: 1. Choose Streaming from the Control Panel to open the Streaming menu. 2. Press Start Streaming from the menu line. 3.
TANDBERG 770_880_990MXP User Manual Remote: Only the far end video will be streamed. Local and far end audio is always streamed. Allow Remote Start Announcements On: Streaming can be started from external user interfaces like the Web-browser or Telnet session. Off: Streaming can only be started from the Video Conferencing System using the remote control, or by using the Data port. This will prevent activation of streaming using Web browser or Telnet sessions.
3 General Use Far End Camera Presets works just like your own camera presets. When Far End is on, use the number keys to activate far end camera presets. You are however not allowed to save far end camera presets. Far End Presentation Pressing the Presentation key or choosing a presentation from the presentation menu while Far End is on, will result in opening a far end presentation. Be aware of that the far end video sources may not correspond with the buttons in the presentation menu.
TANDBERG 770_880_990MXP User Manual The camera position stored at Preset 7 must be related to Microphone 1. Therefore all participants who are located closest to Mic1 should be included in the Preset 7 camera position etc. When camera tracking is activated and a person close to Mic1 speaks, Preset 7 will be automatically selected. When activating another video source (for instance document camera), camera tracking will be temporarily disabled until you re-select Main Camera or a Main Camera Preset.
3 General Use Channel Status View Administrator Settings For more information, see chapter 4.9 Diagnostics. 3.13.8 Administrator Settings Administrator Settings contains the configuration of the whole system. It is recommended to password protect Administrator Settings to prevent occasional users to make changes to the system. See Chapter 4 Administrator Settings for further details. 3.13.9 Restart Restart the system by pressing the Restart button.
4 Administrator Settings Administrator Settings contain all the settings of the system. Making changes to Administrator Settings will change the behavior of the system. It is recommended to password protect the access to Administrator Settings to prevent occasional users from making crucial changes to the system, see chapter 4.2.9 Administrator Password.
4 Administrator Settings 4.1 General Settings When installing the system, go through the General Settings menu to ensure that you have the right settings for your system, see chapter 2.4 System Configuration. General Settings contain: Language System Name Dual Monitor Autoanswer Max Call Length Global Phone Book Settings Permissions Screen Settings Software Options 4.1.
TANDBERG 770_880_990MXP User Manual 4.1.2 System Name System Name identifies the system: on the welcome page. during an MCU conference call. when using the Web-interface. when the codec is acting as an SNMP Agent. towards a DHCP server. as an H323 ID. Other systems can call in using this name instead of IP-number/IPaddress. System Name is blank by default. System name can be alphanumeric and up to 50 characters long. Follow the installation procedure to enter a System Name. 4.1.
4 Administrator Settings 4.1.5 Max Call Length This feature will automatically end both incoming and outgoing calls when the call time exceeds the specified Max Call Length. Max Call Length can have the following values: 0-999 (minutes), where 0 means off. 4.1.6 Global Phone Book Settings Global On Global Phone Book is available in the menu. Off Global Phone Book is hidden from the menu and is unavailable for users. IP address Enter the IP address of the management system that provides the Phone Book.
TANDBERG 770_880_990MXP User Manual Far End Control On The far end will be able to: • Control your camera • Select your video sources • Activate your camera presets • Request snapshots Off The far end can access none of the four features above on the local system. You will however still be able to control the camera on the far end.
4 Administrator Settings Pressing the Layout button on the remote will result in one large image and one or two smaller pictures placed outside the big picture. Press Layout once more to get a side by side view. Press Layout again to go back to normal full screen view. Example of Picture in Picture. Example of Picture outside Picture (wide screen). Example of Side by Side view (wide screen).
TANDBERG 770_880_990MXP User Manual VGA Monitor Format To fully leverage your wide screen display, activate the Native 16:9 format by setting the VGA Monitor Format to Wide. Note that you should only change this setting if your VGA monitor is a wide screen (16:9) monitor or projector. The VGA and DVI output will then be optimized for Wide Screen VGA display.
4 Administrator Settings Auto VGA output format will be optimized dependant of the video source format, refresh and of the EDID information available.
TANDBERG 770_880_990MXP User Manual 4.1.9 Software Options The system requires a valid option key to activate MultiSite and/or Presenter functionality. In order to activate additional bandwidth, you need to enter a bandwidth key. A restart of the system is required after entering a new option and/or bandwidth keys. If the key is invalid, the original key will be used. The following options are available: 1. 2. 3. 4.
4 Administrator Settings 4.2 Menu Settings Menu Settings contain the settings: Menu Timeout In Call Welcome Menu Welcome Picture Logo Menu on TV Menu on PC Display Welcome Text Welcome Text Administrator Password 4.2.1 Menu Timeout In Call Main menu appears on the bottom line of the screen. Set Menu Timeout In Call to On if you want the menu to time out automatically when you are in a call.
TANDBERG 770_880_990MXP User Manual 4.2.2 Welcome Menu The Welcome Menu contains the Main Menu, System Status, your System Name and dial in numbers. On The Welcome Menu is shown when the system wakes up from standby mode. Off The Welcome Menu is not shown when the system wakes up from standby mode. Press the OK button to open the welcome menu. 4.2.3 Welcome Picture The Welcome Picture is what you see in the background of the welcome menu.
4 Administrator Settings 4.2.5 Menu on TV The Menu on TV setting decides if the menu shall be displayed on the TV screen or not. For optimal layout of the menu, 'Menu on TV' should be Off if 'Menu on PC' is On and vice versa. On The menu is available on the TV screen. Off The menu is not available on the TV screen. 4.2.6 Menu on PC The Menu on PC setting decides if the menu shall be displayed on the PC (VGA screen) screen or not.
TANDBERG 770_880_990MXP User Manual 4.2.9 Administrator Password It is recommended to put an Administrator Password on the system. The Administrator Password can be maximum 5 digits long. The Administrator Password dialog box will pop up when you choose Administrator Settings from the Control Panel. This will prevent occasional users from going in to administrator settings.
4 Administrator Settings 4.3 Presentation Settings Presentation Settings contain: Presentation Start H.239 Startup Video Source Presentation Source Snapshot Source Auto-Display Snapshot PIP Appearance PIP Placing VNC Settings 4.3.1 Presentation Start If your system has Duo Video capabilities, you can show two video streams at the same time (see also chapter 3.11.5 Duo Video). Presentation Start is Auto by default.
TANDBERG 770_880_990MXP User Manual Manual When starting a presentation, a dialog box appears asking if you want to start Duo Video. In this way you can choose manually if you want to use Duo Video or not. 4.3.2 H.239 H.239 supports transmission of two video streams. It combines elements of Duo Video and People+Content. If H.239 is disabled you will still be able to start TANDBERG Duo Video. Enabled: Enables H.239 Disabled: Disables H.239 4.3.
4 Administrator Settings 4.3.6 Auto-Display Snapshot Select Auto to automatically display a received snapshot. Turn Auto-Display Snapshot Maual if you wish not to have them displayed on the screen when they are sent or received. The snapshots will be sent and received, but not displayed. With Auto-Display Snapshot set for Manual, you must enter the Presentation menu to display a snapshot. Auto A sent or received snapshot will automatically be displayed on the screen.
TANDBERG 770_880_990MXP User Manual 4.3.9 VNC Settings VNC Settings is necessary when using a VNC presentation. See chapter 3.11.4 PC Soft Presenter and VNC for more about how to use VNC. Address The IP-address of the PC with the VNC software installed. To find the IPaddress of the PC, place the mouse pointer on the VNC program icon in the lower right corner of the Windows taskbar. You can also select Command Prompt from the Startup-menu\Run and type cmd then enter.
4 Administrator Settings 4.4 Call Quality Call Quality contains the settings: Video Algorithm Audio Algorithm AAC-LD 128kbps Natural Video Video Quality Default Call Settings 4.4.1 Video Algorithm The system will automatically select the best video algorithm based on the video source and the capabilities of the remote system. Use this menu to disable video algorithms in case you have interoperability issues calling other systems. H.
TANDBERG 770_880_990MXP User Manual 4.4.2 Audio Algorithm The system will automatically select the best audio algorithm based on the call rate and the capabilities of the remote system. Use this menu to disable audio algorithms in case you want to remove “low quality” audio, or if you have interoperability issues calling other systems. G.722 High quality audio (7 kHz at 48kbps, 56kbps or 64kbps) G.728 Compressed normal quality audio (telephone quality, 3.1 kHz at 16kbps) G.
4 Administrator Settings 4.4.3 AAC-LD 128kbps (stereo audio) Specify a call rate for 128kbps AAC-LD. From this call rate and above, "128kbps AAC-LD" is available. On lower call rates "64kbps AAC-LD" is available. Stereo audio requires twice the bandwidth as mono CD-quality audio. Therefore we recommend to enable stereo audio on high call rates only. To enable stereo CD-quality audio you need to specify a call rate for when stereo automatically should be enabled.
TANDBERG 770_880_990MXP User Manual 4.4.6 Default Call Settings Default Call Settings are connected with Call Settings in the call menu. If you leave Call Settings unchanged when making a call, the system will use the Default Call Settings in the call. See chapter 3.5.4 Call Settings for more information. In addition to the call Settings Call Type, Net, Bandwidth and Restrict (56k), you also find settings for H.320 Auto bandwidth and H.323 Auto bandwidth in Default Call Settings.
4 Administrator Settings 4.5 Audio Audio contains the settings: Inputs Outputs Echo Control Stereo Settings Audio Leveling (AGC) Alert Tones and Volume 4.5.1 Inputs Mic 1- 2 and Audio input 3-4 By default, all inputs are enabled. Just plug in an audio source and it is active. Audio inputs that are On will automatically be mixed. Unconnected inputs will automatically be muted. Select Off to prevent audio/noise from connected but unused inputs.
TANDBERG 770_880_990MXP User Manual Mix Mode Auto The adjustment of each microphone signal is done automatically to obtain the best possible audio and minimize the background noise. Fixed Fixed will maintain a constant weighting of all microphones. VCR Ducking If VCR Ducking is activated, the VCR audio level will be attenuated if someone talks into the microphone or at the far end. Level Settings It is possible to adjust the audio input levels according to which external audio equipment is connected.
4 Administrator Settings If Out 1 Mode is set to Auto, the system will select analog or digital (SPDIF) mode dependent on the detected Audio Module. If a TANDBERG Digital NAM is detected, SPDIF mode will be selected, otherwise analog mode will be selected. Setting the Out 1 Mode to either Analog or SPDIF will override the auto-detected mode. Audio Module Select Audio Module according to the type of Audio Module installed if this is not automatically detected.
TANDBERG 770_880_990MXP User Manual Tips for improving the echo canceller performance: Place all microphones as far as possible from the loudspeaker. Minimum loudspeaker-microphone distance should be 2 meters. It is recommended to place the microphones between 1 and 2 meters away from the persons speaking. By using several microphones, the ratio distance loudspeaker-tomic/mic-to-speaker can be increased. Increasing this ratio improves the echo canceller performance.
4 Administrator Settings Example: In most conferences, the participants will speak at different levels, and be at different distances from the microphones. As a result, some of the participants would be harder to hear than others. The AGC corrects this problem by automatically increasing the microphone levels when “quiet” or “distant” people speak, and by decreasing the microphone levels when “louder” people speak. 4.5.
TANDBERG 770_880_990MXP User Manual 4.6 Video Video contains the settings: Camera Tracking Mode MCU Status Line Floor to Full Screen Web Snapshots MultiSite Picture Mode Picture Control Video Name 4.6.1 Camera Tracking Mode Slow: The system waits a while before zooming in on a single person speaking. Suitable when wide-angle images are preferred over close-up images. Normal: Should be used in regular meetings. Fast: The system quickly zooms in on a single person speaking.
4 Administrator Settings 4.6.2 MCU Status Line On The MultiSite/MCU/DuoVideo indicators will be displayed and provide information about the conference. Off The MultiSite/MCU/DuoVideo indicators will not be displayed. Auto The MultiSite/MCU/DuoVideo indicators will be displayed for a few seconds and then timed out. When grabbing the remote control, the indicators will be shown again. 4.6.
TANDBERG 770_880_990MXP User Manual 4.6.5 MultiSite Picture Mode MultiSite Picture Mode decides the default layout of a multipoint call. Choose between the layouts: Auto Split, Voice Switched, 4 Split and 3 +1 Split. You can change the layout during a call using the layout option in Multipoint Services. Auto Split Auto Split displays all participants on the screen simultaneously. A multipoint call with 3 and 4 video participants is displayed with 4 Split.
4 Administrator Settings 4.6.6 Picture Control Focus, Brightness and White balance are set for auto focus, auto brightness and auto white balance by default. If you need to set focus, brightness and white balance manually, go to Picture Control in Video Settings. Focus Auto In Auto mode the focus is continuously updated. When moving the camera, the system will use auto focus for 5 seconds to set the right focus of the new camera position.
TANDBERG 770_880_990MXP User Manual 4.7 Security Security contains the settings: Encryption Encryption Mode Passwords 4.7.1 Encryption (Country specific) Auto The system will try to set up calls using encryption. Point to point calls: If the far end system supports encryption (AES or DES), the call will be encrypted. If not, the call will proceed without encryption. MultiSite calls: In order to have encrypted MultiSite calls, all sites must support encryption.
4 Administrator Settings On The system will only send and receive encrypted data. The call will not be established if not all participants support encryption. Off The system will not send or receive encrypted data. Technical encryption information like encryption algorithm and encryption check code can be found in the Call Status menu. 4.7.2 Encryption Mode Auto The system will try to use the most secure encryption - AES, dependent on the capabilities of the other sites.
TANDBERG 770_880_990MXP User Manual 4.8 Network The network menu contain: ISDN-BRI Settings LAN Settings Network Profiles Data Port 4.8.1 ISDN-BRI Settings To make sure your system will work properly using ISDN-BRI, make the following settings: 1. Set ISDN switch type 2. Enter ISDN line numbers (+ SPIDs if required) 3. Disable unused lines Some software versions do not support 6 ISDN lines, therefore some of the Line Setup entries may be grayed out. 4.8.1.
4 Administrator Settings Example: Numbers SPIDS ISDN BRI 1: 67838498 67838498 016783849800 016783849810 ISDN BRI 2: 23478060 23478070 012347806000 012347807000 ISDN BRI 3: 23478420 23478430 012347842000 012347843000 ISDN BRI 4: 23478520 23478530 012347852000 012347853000 4.8.1.3 Advanced ISDN Settings Sub address Using a sub address enables you to connect up to eight ISDN terminals to the same ISDN telephone number and line. The terminals are addressed by using different sub addresses.
TANDBERG 770_880_990MXP User Manual Off The system will not send Sending Complete. 4.8.2 LAN Settings LAN Settings contain: IP Settings H.323 Settings SNMP Settings Wireless LAN Settings 4.8.2.1 IP Settings Remember to restart the system after making changes to IP Settings. Changes in IP Settings menu will not have any effect before the system is restarted. IP-assignment DHCP (Dynamic Host Configuration Protocol) can be selected when a DHCP server is present.
4 Administrator Settings 10/Full 10 Mbps speed/Full Duplex. 100/Half 100 Mbps speed/Half Duplex. 100/Full 100 Mbps speed/Full Duplex. IP Access Password By setting an IP Access Password on the system, all access to the system using IP (Telnet, FTP and WEB) requires a password. The default IP Access Password is “TANDBERG”. 4.8.2.2 H.323 Settings 4.8.2.2.1 E.164 alias This is the E.164 address of the system. The E.
TANDBERG 770_880_990MXP User Manual 4.8.2.2.4 Gatekeeper IP-address This is the gatekeeper IP-address that is used if you specify H.323 Call Setup: Gatekeeper and Gatekeeper Discovery: Manual. 4.8.2.2.5 Call Manager Address This is the call manager IP-address that is used if you specify H.323 Call Setup: Call Manager. 4.8.2.2.6 H.323 Prefix When dialing a number prefixed with digits specified by H.323 Prefix, and with Net: Auto, an H.323 call will be placed. Example: H.323 Prefix is "555".
4 Administrator Settings RSVP Auto Resource Reservation Protocol enables the systems to request the optimal amount of bandwidth for the duration of an IP videoconference. Off Resource Reservation Protocol is switched off. QoS Type Off No QoS is used. Diffserv Diffserv QoS method is used. Please see below for details. IP Precedence IP Precedence QoS method is used. Please see below for details.
TANDBERG 770_880_990MXP User Manual Diffserv Video Used to define which priority Audio, Video, Data and Signaling packets should have in an IP network. The priority ranges from 0 to 63 for each type of packets. Diffserv Telephony Used to define which priority Audio packets should have in an IP network for telephone calls. The priority ranges from 0 to 63 for each type of packets. H.323 Ports Static When selecting static H.323 ports for TCP connections the ports 5555 or 5556 will be used for Q.931 and H.
4 Administrator Settings WLAN Mode AdHoc: Used when not communicating with an access point. Managed: Used when communication is made through an access point. Make sure the corresponding settings are programmed into the access point. Press “Restart” from Control Panel in order to activate the settings. Required cards • Compaq WL110 11 Mbps Wireless LAN • Lucent Orinoco 11 Mbit/s SILVER • Lucent Orinoco 11 Mbit/s GOLD • Cisco Aironet 350 series (AIR-PCM 350 series) • Enterasys Networks RoamAbout 802.
TANDBERG 770_880_990MXP User Manual Using the three last profiles you can enter the name of a profile, prefix and network selection. This is useful if you have a fixed prefix for your service provider. 4.8.4 Data Port The system provides two standard RS232 serial ports to allow a computer to be connected for data transfer and control purposes. Note that when connecting to a PC the connecting cable must be a straight through RS232 cable.
4 Administrator Settings 4.9 Diagnostics Diagnostics allows testing of individual system components and displays the current system settings. Diagnostics contain: System Information Call Status Channel Status System Selftest View Administrator Settings Restore Default Settings IP Address Conflict Check 4.9.1 System Information Select System Information to view system numbers, line status, software version and other useful information.
TANDBERG 770_880_990MXP User Manual 4.9.2 Call Status Comprehensive information about the call is available through the Call Status window. The menu has two columns, one for transmitted and one for received audio/video/data information. If Duo Video or MultiSite is used, pressing the UP/DOWN keys will show one page per connected site. Some of the information fields will vary dependent on if H.320 (ISDN calls) or H.323 (IP calls) are made. 4.9.
4 Administrator Settings PRI Red Alarm Red alarm or Loss of signal (LOS) means that there is no signal and thus no framing info received (this has same effect as pulling out the PRI cable). PRI Yellow Alarm Yellow alarm or Remote Alarm Indicator (RAI) means that the system is receiving framing info, but in this framing info the other side tells the system that it is not reading the system’s transmitted framing info. Typically, this may be a broken connector in the TX part of the system PRI cable.
TANDBERG 770_880_990MXP User Manual Fallback to Telephony Screen Settings TV Monitor Format Picture Layout VGA Monitor Format VGA Out Quality PC Picture Format Allow VGA 50Hz Software Options Options Installed Hardware Serial Number Current Option Key Menu Settings Menu Timeout in Call Welcome Menu Welcome Picture Logo Display Welcome Text Welcome Text Administrator Password Presentation Settings Duo Video Mode Start up Video Source Presentation Source Snapshot Source Auto Display Snapshot PIP Appea
4 Administrator Settings Mic2 Mic3 Audio4 Audio Leveling (AGC) Mic1-3, Audio4 Audio5 (AUX) Audio6 (VCR) Received Audio Alert Tones & Volume Video Call Alert Tone Telephone Alert Tone Alert Speaker Key Tones Video Settings Camera Tracking Mode MCU Status Line Web Snapshot MultiSite Picture Mode Picture Control Focus White balance Brightness Video Name Main Cam AUX Doc Cam VCR PC VGA VNC Network Type ISDN-BRI\PRI\Leased E1\T1\Enternal H331 ISDN Switch Type ETSI (Euro ISDN),… Line1 Setup On Number1
TANDBERG 770_880_990MXP User Manual E1 CRC-4 Advanced ISDN PRI Settings NSF Code Video NSF Code Telephone Call Leased E1/T1 Settings Call Control Network Interface Max Channels Start Channels T1 Line Coding Line Settings External network configuration Call Control RS66 RS449/V.35 Compatible IP Settings IP assignment IP address IP subnet mask Gateway Ethernet Speed H.323 Settings E.164 Alias Use Gatekeeper Gatekeeper IP H.323 Prefix Advanced H.
4 Administrator Settings Mode Data Port 2 Baud rate Parity Databits Stopbits Mode 4.9.6 Restore Default Settings Restore Default Settings will restore all administrator settings. Note that this will not affect your Call Directory information, Network Type, Line Setup numbers or your SPID numbers. 4.9.7 IP Address Conflict Check The system will give a warning if there is an IP conflict. The user may initiate this check by selecting IP Address Conflict Check.
5 Peripheral Equipment Using the optional peripheral devices outlined in this chapter and the many others available, you will be able to build your own applications for use with the system, thereby better integrating the system into your business environment. This chapter will explain how to connect peripheral equipment to your system. First of all however, we recommend you examine the figure below detailing the available connectors on the back of the system Codec.
5 Peripheral Equipment 5.1 Interfaces 5 Video Inputs 1 video input used by the built-in camera. 1 video input supporting S-Video through a Mini-DIN connector. 2 video inputs supporting composite signals through RCA connectors. 1 VGA/DVI-I (DVI = Digital Video Interface, I = Integrated Digital & Analog) input supporting resolutions VGA (640x480), SVGA (800x600), XGA (1024x768) and SXGA (1280x1024), analog or digital. The system will automatically adapt to a PAL or NTSC input.
TANDBERG 770_880_990MXP User Manual 1 VCR output (line level) via RCA connector providing a mixed signal between audio from the local side (except from the VCR input) and audio from the far end. This output is intended for connection to a VCR.
5 Peripheral Equipment 5.2 Document Camera A document camera can be used for showing text, diagrams and a variety of graphical material as well as small three-dimensional objects. How to use a document camera with your system: 1. Connect the document camera to the Doc Cam input on the system. 2. Open the Presentation menu from Main menu and choose Doc Cam. 3. You can also program the Presentation key on the remote to activate document camera. See chapter 3.11.1 Presentation Key for more information.
TANDBERG 770_880_990MXP User Manual 5.3 Video Cassette Recorder (VCR) VCR/DVD - Playback Mono For playback, connect a cable between Video Out on the VCR and Video In (VCR) on the system. Connect a cable between Audio Out on the VCR and the Audio In (VCR) on the system. Choose VCR from the Presentation menu to activate the VCR input. Make sure that Audio In (VCR) is On (see chapter 4.5 Audio). If audio from VCR is too low, this level can be adjusted in Audio Settings, Inputs, Level Settings.
5 Peripheral Equipment 5.4 Telephone Add-On The system have a built in audio bridge* that can bring in Voice over IP (VoIP) telephony or normal telephone sites using ISDN. It can bridge upto 3 telephony sites in any mix.
TANDBERG 770_880_990MXP User Manual 5.5 Additional Cameras Extra fixed Cameras You can connect extra fixed cameras to your system, for example, a whiteboard camera. Connect the video output of the additional camera to one of the available Video inputs on the system.
5 Peripheral Equipment 5.6 Additional Microphones If your environment is such that you require more than one microphone for your room, e.g. you have a whiteboard at a distance from your table microphone; it is possible to connect additional microphones to your system. See Appendix 5 for more information. If your environment is such that you require more microphones for your room, e.g.
TANDBERG 770_880_990MXP User Manual 5.7 Web Interface It is possible to access and maintain the system remotely via a local area network (LAN) using a standard Web-browser. Connect your system to a LAN with a Network cable. How to configure your system for web interface: 1. Open Administrator Settings and choose Network\LAN Settings 2. Specify IP-assignment DHCP or Static. If DHCP is selected, no other settings are needed. If Static is selected, IP-address, IP-subnet mask and Gateway must be specified. 3.
5 Peripheral Equipment 5.8 Dual Monitor It is possible to install the system in a Dual Monitor configuration. The Dual Monitor can be used to show full screen selfview, still images and Duo Video. To use the system in the Dual Monitor configuration: 1. Connect "Video Out 3" (composite video output) on the system to a video input on the dual monitor. 2. Set "Dual Monitor: On" in General Settings menu. Alternatively you can use a PC monitor as your second monitor: 1.
TANDBERG 770_880_990MXP User Manual 5.9 XGA Monitors and Projectors (Optional) The system can be delivered with optional single or dual TV/XGA monitors. It can also be connected to any DVI/VGA/PAL or NTSC display. Note that the unit supports VESA Display Power Management on the DVI/VGA output (see chapter 5.10 VESA Display Power Management) and can be used to put your VGA monitors/projectors to standby when the system goes into screensaver mode.
5 Peripheral Equipment 5.10 VESA Display Power Management Because of the tremendous amount of energy consumed by monitors when operating, the system will reduce power consumption and extend monitor lifecycle by suspend (switch off) monitors and projectors when the system goes into sleep/standby.
TANDBERG 770_880_990MXP User Manual 5.11 Extended Display Identification Data (EDID) Extended Display Identification Data (EDID) is a VESA standard data format that will allow the system to communicate its capabilities, including vendor information like the supported VGAformats and frequency range limits to a PC connected to the XGA/DVI input. This means that the PC always* will be able to output a valid VGA/DVI signal to the system with no manual reconfiguration of the PC screen settings.
6 Appendix Appendixes: Appendix 1: Connecting the system to ISDN using NT1 network adapters Appendix 2: Connecting the system to the Switched 56 network Appendix 3: Connecting the system to PRI/T1 Appendix 4: Environmental considerations Appendix 5: Guidelines for setting up videoconferencing rooms Appendix 6: Using the file system Appendix 7: Security Appendix 8: Pinouts and Connectors Appendix 9: Cisco CallManager registration Appendix 10: Diagnostic Tools for IP Appendix
TANDBERG 770_880_990MXP User Manual 6.1 Appendix 1 Connecting the system to ISDN using NT1 network adapters Connecting Connect the first ISDN cable from ISDN 1 on the system to the S-interface on your first NT1 network adapter. Connect the other ISDN cables to the appropriate NT1 network adapters. Connect the U-interface of your NT1 adapter to the line provided from your network provider. For convenience the NT1 adapters could be placed inside the cabinet.
6 Appendix 6.2 Appendix 2 Connecting the system to the Switched 56 network Using Telesync TS-256 SW56/ISDN adapter Connecting the system to the SW56 network using a Telesync Adapter is described below. There are different Telesync Adapters for different configurations of SW56 networks. The network types tested with the system are SW56 2Wire and 4Wire. Connecting Connect the system ISDN1 cable to the BRI S/T interface on the Telesync Adapter.
TANDBERG 770_880_990MXP User Manual 6.3 Appendix 3 Connecting the system to PRI/T1 Using CSU adapter Connecting the system to the ISDN network via the E1/T1interface using an Adtran T1 ESF CSU ACE or equivalent CSU, will allow up to 1.54 Mbps connection. The E1/T1-interface must be connected to a CSU approved according to IEC 60950, UL 1950 or equivalent standard. The PRI-line will run the AT&T 4ESS, 5ESS and National ISDN protocols in addition to Euro ISDN (E1).
6 Appendix 6.4 Appendix 4 Environmental considerations This section explains how to carry out basic adjustments and simple tests to ensure that you send and receive the best possible image and audio quality when using your system. Iris control and lighting By default the system camera will use an automatic iris to compensate for changes in lighting.
TANDBERG 770_880_990MXP User Manual 6.5 Appendix 5 Guidelines for setting up videoconferencing rooms The following are a set of guidelines to consider when either building a videoconferencing room, or using an existing room for videoconferencing. Lighting: Low Contrast desired for light intensity. No dark spots. Intensity @ table 800 - 1400 Lux as measured with an Incident light meter. Block sunlight from entering room. Seating Area (Table): Should allow all participants to see Monitors.
6 Appendix The microphone should be placed at the front of the table to ensure that all speech will be detected. The best position for the microphone is at least 2 meters (6.5 feet) in front of the system on a plain, flat table with at least 0.3 meters (12 inches) of table in front of the microphone.
TANDBERG 770_880_990MXP User Manual 6.6 Appendix 6 Using the file system It is possible to access a file system within the TANDBERG system by using ftp: DOSwindow: ftp , or Webbrowser: ftp:// Description of the different files: all.prm all settings in the system (including directory) dir.prm directory entries (up to 200 entries) event.log logs fault situations etc. sw.pkg the system software globdir.prm file containing up to 400 entries.
6 Appendix Enter password: Go to the remote folder, type “cd remote” Upload the software file, type put Wait until the following is shown: 226 Closing data connection. 5437569 bytes sent in 808.01 seconds (6.73 Kbytes/sec) ftp> Restart the far end system. The far end system should now be upgraded. For further information, please contact your TANDBERG representative. Custom logos Go to the folder where your logo is located.
TANDBERG 770_880_990MXP User Manual 6.7 Appendix 7 Security The system has several features both to protect from unauthorized use and system access: Access Code: When Access Code is enabled, the user will be asked to enter an access code before he/she is able to make a call. The system will verify if the entered access code is valid by checking the code with the allowed codes listed in the access.txt file on the ftp-server in the system. If no access.
6 Appendix To remove this password, use the command: "ippassword ”. From telnet, this is only possible by first entering the correct password. Services The different IP services on the system - FTP, Telnet, Telnet Challenge, HTTP, HTTPS, SNMP and H.323 can be disabled to prevent access to the system.
TANDBERG 770_880_990MXP User Manual The TANDBERG AES implementation is validated as conforming to the Advanced Encryption Standard (AES) Algorithm, as specified in Federal Information Processing Standard Publication 197, Advanced Encryption Standard, by The National Institute of Standards and Technology (NIST).
6 Appendix 6.8 Appendix 8 (Not for set top systems) Pinouts and Connectors WAVE II Camera: 8-PIN RJ (shielded modular jack): This connector is used for the power and control signals to the main camera. Pin-8 +12V (presence when connected in daisy chain) Pin-7 GND Pin-6 GND Pin-5 RXD (in) Pin-4 TXD (out) Pin-3 +12V Pin-2 GND Pin-1 + 12V Standard Phono: Used for composite video signal Power: 2.
TANDBERG 770_880_990MXP User Manual Multiple Camera support: The figure below is an example of how multiple cameras should be connected: Ethernet: To connect the system to a LAN, use the Ethernet cable provided by TANDBERG (or a standard Ethernet cable). If no LAN is available and the codec is connected directly to a computer, use a crossover cable.
6 Appendix PRI ISDN Interface: To connect the system to PRI, use the ISDN cable provided by TANDBERG (or a standard PRI cable).
TANDBERG 770_880_990MXP User Manual 6.9 Appendix 9 Cisco CallManager registration Configuring an H.323 client on the CallManager 4.0 The registration of a H.323 client in CallManager is supported on the CallManager (CCM) 4.0 software and forward. 1. To configure the CallManager with an H.323 client, log on to the administration web interface and go to the phone configuration page. 2. The Phone configuration page is located on: device (top menu) -> Add a New device -> Phone -> H.323 Client. 3.
6 Appendix 6.10 Appendix 10 Diagnostic Tools for IP To use these tools, will require using a PC and setting up a telnet session towards the system. Q.931 To show Q.931 trace during a call you need to issue the command ‘syslog on’.One can get traces for RAS, Q.931 and H.245 with this command. It is a complex trace and requires an extensive knowledge in H.323 signalling to be understood. Ping Ping is used to see if the system is able to reach a specific IP-address, using a mechanism in IP called ICMP.
TANDBERG 770_880_990MXP User Manual (*) Note: While using MultiSite, if a site is disconnected and reconnected without terminating the entire conference, the next site to be connected will have a H.245 port outside of the specified range. If this functionality is required through a firewall, the range of TCP ports can be extended past 5564. However, if a site is disconnected and reconnected, without ending the conference enough times one can quickly end up outside of this range again.
6 Appendix 6.11 Appendix 11 Declaration of Conformity Contact your TANDBERG representative for a Declaration of Conformity.
Glossary # 199 AV1: External input for the TANDBERG/LOEWE monitor. 2nd monitor: The second monitor of your videoconferencing system. The second monitor is normally placed on the right side of the first monitor. 4CIF: 4 times CIF, 704x576 pixels 4SIF: 4 times SIF, 704x480 pixels A AACLD: Advanced Audio Coding Low Delay Access code: Use Access code to password protect outgoing calls. Accessories box: The cabinet contains the following: W.A.V.E.
Glossary Call control Data Triggered: Uses TxData, RxData and clock signals only. Use Data Triggered when no handshake signal is available. Call control Leased Line: Is a non-dialing protocol and should be used when two systems are connected in a point-to-point connection. Use Leased Line when the handshaking signals DTR and CD are available. Call control Manual: Should be used when no handshake signals are available, and the external equipment requires a constantly connected line.
TANDBERG 770_880_990MXP User Manual Disconnect site: As a Chairman, you get the option Disconnect site. Disconnect site allows you to disconnect any participant in the conference. Do Not Disturb: When Do Not Disturb is active the system will not accept any incoming calls. The caller will hear a busy tone when calling the unit. Document Camera: A document camera is an additional camera that is used for showing text, diagrams as well as physical objects.
Glossary Gateway: The gateway enables sites on IP and sites on ISDN to participate in meetings with each other. Global Phone Book: A phone book provided by TMS. H H.261: Video algorithm for legacy video compression and decompression. The system will always transmit H.261 H.263: Video algorithm for normal video compression and decompression H.264: Video algorithm for bandwidth-efficient video compression and decompression Humfilter: A highpass filter which reduces very low frequency noise.
TANDBERG 770_880_990MXP User Manual Modem mode: (Dataport) Supports external control of the system via a PC as in Control Mode. Once a call is established, Dataport 1 will automatically switch to Data mode. When the call disconnects, Dataport 1 switches back to Control Mode. MSN: Multiple Subscriber Number. Possible to attach different ISDN terminals, with different numbers, to the same physical ISDN telephone line. The service can be ordered from the telephone company.
Glossary Parallel dial: Channels will be dialed and connected in parallel when setting up a bonding call. PC PresenterTF: An easily accessible PC connection plug. When connected the PC image is displayed on the monitor. PC SoftPresenterTF: Shows PC images via the LAN connection. PIP: Picture-In-Picture point-to-point call: A call with two participants including your self POP: Picture Outside Picture.
TANDBERG 770_880_990MXP User Manual SNMP traps: Generated by the agent to inform the manager about important events. SoftMux: Ensures high reliability and includes the unique Downspeeding feature. It also makes it possible to dial to another videoconferencing equipment, phones and mobile phones in a uniform way, and provides an on-screen, real-time feedback on the progress of a call. Split Screen: All the participants in a MultiSite conference are displayed on the screen.
Glossary TMS: TANDBERG Management Suite Touch Tones: To dial extension numbers ect. during a call, use touch tones in order to get tones instead of preset on the number keys. Tracker: The tracker is a small infrared remote control device made to steer the camera to any desired location within the room. TSC-1: TCS-1 is used for H243 password on H320 MCU's V VCR: Video Cassette Recorder VGA: Video Graphics Array.
Index A Add Another Call.....................................28 Additional microphone ..........................114 Administrator Password..........................71 Alert Tones and Volume .........................85 Answer an incoming Call ........................31 Assign Floor to Participant......................50 Audi Algorithm ........................................77 Audio Inputs ..................................................81 Outputs................................................
TANDBERG 770_880_990MXP User Manual Z 150 Zoom ......................................................
