Installation Instructions

ManualsBrandsSharp ManualsMicrowave/Micro Hood AccessoriesSharp 27" Stainless Steel Built-In Trim Kit

For Sharp Built-in Kit Models RK-94S27 or RK-94S30

THIS KIT IS UL APPROVED TO ALLOW CERTAIN MICROWAVE OVENS TO BE INSTALLED

ABOVE ANY ELECTRIC WALL OVEN. PLEASE SEE THE OPERATION MANUAL

REGARDING APPROVED BUILT-IN APPLICATIONS.

IMPORTANT:

This Built-in Kit is designed for and approved only for those Sharp

Microwave Ovens specifying Built-In Kit RK-94S27 or RK-94S30.

Refer to operation manual for approved models or www.sharpusa.

com\trimkits

PLEASE READ THESE INSTRUCTIONS

THOROUGHLY BEFORE

BEGINNING INSTALLATION!

• Always DISCONNECT THE PLUG of the microwave oven from the

electrical outlet before installing the Built-in Kit. Remove the Carou-

sel turntable from the oven cavity.

• Because the kit includes metal parts, due caution should be used

in handling and installation to avoid the possibility of injury.

INSTALLATION INSTRUCTIONS

ITEM PART NAME QTY

A DUCT (A)-1

PDUC-0259WRW0

B DUCT (A)-2

PDUC-B127MRP0

C DUCT (A)-3

PDUC-A734WRW0

D DUCT (B)

PDUC-0260WRW0

E DUCT (C)

PDUC-A274WRW0

F BOTTOM DUCT ASSEMBLY

FDUC-B099MRK1A

G M3.9-16MM PAN HEAD TAPPING

SCREW, ZINC

XOPS740P16000

H WOOD SCREW

XTSS740P20000

I CABINET SCREW/ CLEAR

XOTS740P12000

J FRONT FRAME

RK-94S27: FDECAB229MRK0

RK-94S30: FDECAB227MRK0

K BACK FRAME

RK-94S27: FDECAB230MRK0

RK-94S30: FDECAB226MRK0

L CUSHION SHEET

PCUSGB059MRP0

Check list for parts when unpacking. Note J. Front

Frame and K. Back Frame are shipped attached.

Snap apart before installation.

DUCT (A)-1

DUCT (A)-2

DUCT (A)-3

DUCT (B)

DUCT (C)

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS For Sharp Built-in Kit Models RK-94S27 or RK-94S30 THIS KIT IS UL APPROVED TO ALLOW CERTAIN MICROWAVE OVENS TO BE INSTALLED ABOVE ANY ELECTRIC WALL OVEN. PLEASE SEE THE OPERATION MANUAL REGARDING APPROVED BUILT-IN APPLICATIONS. IMPORTANT: This Built-in Kit is designed for and approved only for those Sharp Microwave Ovens specifying Built-In Kit RK-94S27 or RK-94S30. Refer to operation manual for approved models or www.sharpusa.
PAGE 2
STEP 1 CABINET OR WALL OPENING Outlet should NOT be in the shaded area as indicated on Figure 1. Provide an opening in the wall or cabinet as indicated in Figure 1. The depth should be a minimum of 20-1/8". If the Depth (E) dimension is greater than 21", the outlet location may be in any area on the rear wall. The floor of the opening should be constructed of plywood strong enough to support the weight of the oven (approximately 100 lbs.) and should be level for proper operation of the oven.
PAGE 3
E. Carefully turn over exhaust assembly. Remove adhesive backing from CUSHION L. The cushion should be applied to the flanges of the duct assembly as indicated by arrows. See Figure 5A. F. Remove SCREW from the upper right and left corners at the rear of the oven. Place duct assembly on the top of the unit as shown and secure the duct assembly to the oven using the two screws just removed from the oven. See Figure 5B. SCREW SCREW CUSHION L Figure 5B Figure 5A STEP 3 SURFACE INSTALLATION B.
PAGE 4
C. CABINET INSTALLATION: Avoid pinching the cord between the oven and the wall. Adjust the position of the oven so that the feet of the oven are fitted into the holes of the Bottom Duct Assembly. See Figure 8. E. FRONT FRAME INSTALLATION: Place the FRONT FRAME onto the BACK FRAME and align ball studs and receivers. Secure the FRONT FRAME to the BACK FRAME by firmly pushing the front frame onto the back frame engaging the four (4) snap attachments. See Figure 10.
PAGE 5
INSTRUCTIONS D'INSTALLATION Pour les ensembles de modèles Sharp à encastrer RK-94S27 ou RK-94S30 CETTE TROUSSE EST CONFORME AUX NORMES UL EN CE QUI CONCERNE LA POSSIBILITÉ D'INSTALLER CERTAINS FOURS À MICRO-ONDES AU-DESSUS DE TOUT FOUR ENCASTRÉ ÉLECTRIQUE. VEUILLEZ CONSULTER LE MODE D'EMPLOI CONCERNANT LES TYPES D'INSTALLATIONS ENCASTRÉES APPROUVÉES.
PAGE 6
ÉTAPE 1 OUVERTURE DE L'ARMOIRE OU DU MUR Faire une ouverture dans le mur ou l'armoire comme illustré à la Figure 1. La profondeur doit être d'une longueur minimum de 51,1 cm (20 1/8 po). Si la profondeur (E) dépasse 53,3 cm (21 po), l'emplacement de la prise peut être situé n'importe où sur le mur arrière.
PAGE 7
E. Tourner avec précaution sur l'assemblage d'échappement. Retirer support adhésif COUSSIN L. Appliquer les coussins aux brides de l'ensemble conduit comme indiqué par les flèches. Voir schéma 5A. F. Retirer la VIS des coins supérieurs droit et gauche à l'arrière du four. Placer l'ensemble conduit au-dessus de l'appareil comme illustré et fixer l'ensemble conduit sur le four à l'aide des deux vis qui viennent d'être retirées. Voir schéma 5B.
PAGE 8
C. INSTALLATION DANS L'ARMOIRE : Éviter de pincer le cordon entre le four et le mur. Ajuster la position du four de façon à ce que ses pattes entrent dans les trous de l'assemblage de conduit inférieur. Voir schéma 8. E. INSTALLATION DU CADRE DE FAÇADE : Poser le CADRE DE FAÇADE sur le CADRE ARRIÈRE et aligner les pivots à rotule avec les agrafes. Fixer le CADRE DE FAÇADE en le poussant fermement contre le CADRE ARRIÈRE et en engageant les quatre (4) fixations encliquetables. Voir schéma 10.