Datasheet

ManualsBrandsSHARP ManualsSolid State RelaysSolid State Relays

S102T01/S102T02

S202T01/S202T02

S102T01/S102T02/S202T01/S202T02

1. Programmable controllers

2. Air conditioners

3. Copiers

4. Automatic vending machines

■ Features

■ Applications

Low Profile Type

Solid State Relays

1. Low profile type (height:16mm)

2. Built-in zero-cross circuit (S102T02/S202T02)

3. RMS ON-state current I

(rms) : MAX. 2A (T

≤40˚C)

4. Recognized by UL, file No.E94758

Approved by CSA, No.LR63705

Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP

devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.

Internet Internet address for Electronic Components Group http://sharp-world.com/ecg/

■ Outline Dimensions

(Unit : mm)

(3.8)

(5.08) (10.16)

(2.54)

1 2 3 4

∼

★

+−

1.8

4.511.5

3.8

MAX.

0.2

MAX.

6.2

MIN.

1.6

3-1.2

6.4

Common to pin No.2

3-1.4

(3.5)

(0.8)

(25.8)

Zero cross circuit

0.4

Lot No.

(DIN Standard)

Epoxy resin

(1.8)

4-0.8

1.8

0.1

MIN.

Common to pin No.2

φ3.7

4321

Output (Triac T1)

Output (Triac T2)

Input (+)

Input (−)

S102T02/S202T02S102T01/S202T01

Internal connection diagram

A(Model No.) B

S102T01

S102T02

S202T01

S202T02

2A125VAC

2A265VAC

0.5

★ : Do not allow external connection.

❈( ) : Typical dimensions

■ Model line-up

For 100V lines For 200V lines

No zero-cross circuit

Built-in zero-cross circuit

S102T01

S102T02

S202T01

S202T02

■ Absolute Maximum Ratings

*1 Refer to Fig.2, Fig.3

*2 60Hz sine wave, start at T

=25˚C

*3 Isolation voltage measuring method

(1) Dielectric withstand voltage tester with zero cross circuit shall be used

(2) The applied voltage waveform shall be sine wave

(3) Voltage shall be applied between input and output

(Input and output terminals shall be shorted respectively)

(4) 40 to 60%RH, AC 60Hz, for 1minute

*4 For 10s

Parameter Symbol Rating Unit

A/µs

Input

Output

400

600

400

600

/dt

T(rms)

DRM

surge

DSM

45 to 65

3.0

260

iso (rms)

Repetitive

peak OFF-state

voltage

Forward current

RMS ON-state current

Peak one cycle surge current

Reverse voltage

opr

−30 to +125

−25 to +100

sol

stg

˚C

=25˚C)

S102T01

S102T02

S202T02

S202T01

S102T01

S102T02

S202T01

S202T02

Non-repetitive

peak OFF-state

voltage

Critical rate of rise of ON-state current

Operating frequency

Operating temperature

Storage temperature

Isolation voltage

Soldering temperature

Summary of content (5 pages)

PAGE 1
S102T01/S102T02/S202T01/S202T02 S102T01/S102T02 S202T01/S202T02 Low Profile Type Solid State Relays ■ Features ■ Outline Dimensions 1. Low profile type (height:16mm) 2. Built-in zero-cross circuit (S102T02/S202T02) 3. RMS ON-state current IT (rms) : MAX. 2A (Ta≤40˚C) 4. Recognized by UL, file No.E94758 Approved by CSA, No.LR63705 Common to pin No.2 IT(rms) Isurge Output 0.1MIN. 4.5 IF VR 11.5 A B ∼ ★ 50 6 *1 2 20 0.2MAX. 3.8MAX. 6.2MIN. Rating (Ta=25˚C) Unit mA V A A 2 3 (1.8) 4 (10.
PAGE 2
S102T01/S102T02/S202T01/S202T02 Transfer characteristics Output Input ■ Electro-optical Characteristics Parameter Forward voltage Reverse current Repetitive peak OFF-state current ON-state voltage Holding current Critical rate of rise of OFF-state voltage Symbol VF IR IDRM VT (rms) IH dV/dt Conditions IF=20mA VR=3V VD=VDRM IT (rms)=2A, Resistance load, IF=20mA − VD=2/3VDRM MIN. − − − − − 30 TYP. 1.2 − − − − − 1×10−4 1×10−4 1.
PAGE 3
S102T01/S102T02/S202T01/S202T02 Fig.3 Forward Current vs. Forward Voltage Fig.4 Surge Current vs. Power-on Cycle 50 25 f=60Hz Tj=25˚C start Ta=75˚C 50˚C 20 25˚C 0˚C −25˚C 5 Surge current Isurge (A) Forward current IF (mA) 10 1 0.5 15 10 5 0.1 0 0.6 0.8 1.0 1.2 1.4 1.6 1.8 1 10 Forward voltage VF (V) Power-on cycle (Times) Fig.5 Minimum Trigger Current vs.
PAGE 4
S102T01/S102T02/S202T01/S202T02 Fig.8 Repetitive Peak OFF-state Current vs. Ambient Temperature S102T01/S102T02 −4 10−5 S102T01 10−6 S102T02 10−7 10−8 10−9 −25 0 25 50 75 Ambient temperature Ta (˚C) 100 S202T01/S202T02 10−3 VD=400V Repetitive peak OFF-state current IDRM (A) Repetitive peak OFF-state current IDRM (A) 10−3 10 Fig.9 Repetitive Peak OFF-state Current vs.
PAGE 5
NOTICE ● The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. ● Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.