Specifications
Maxiva UAX
October 17, 2013
5‐25
888‐2693‐004 WARNING:Disconnectprimarypower priortoservicing.
Copyright©2013,HarrisBroadcast
STEP 5 Connectthevideosourcetothevideoinputofthetransmitter.Setvideo
sourcetoblackpicturewithzerosetup.
STEP 6 IfdualLPUsareinusesettheTCUDriverControltoManual.SelecttheLPU
tobecalibratedastheactiveLPU.
STEP 7 PressandholdtheLowerbuttonfor30‐40secondstoreducetransmitterRF
outputatturn‐on.UsetheTCULowerbuttonfordualsystems.UsetheLPU
LowerbuttonifasingleLPUispresent.
STEP 8 TurntransmitteronbypressingtheOnbutton.UsetheTCUOnbuttonfor
dualsystems.UsetheLPUOnbuttonifasingleLPUisinuse.
STEP 9 SetbothNon‐LinearandLinearRTACtoBypass.ThisisdoneviatheLPUfront
panelLCDorviatheLPUGUIscreenshowninFigure5‐14onpage5‐23.
STEP 10 StartcalibrationbynavigatingtotheSystemCalibrationscreenonleftin
Figure5‐13onpage5‐23.
STEP 11 SelectForwardcalibration.SelectStartCal.Note:thesoundcarrieris
automaticallyextinguishedoncetheCalroutineisstarted.
Caution
DO NOT DEPRESS THE POWER RAISE BUTTON FOR EXTENDED PERIODS
OF TIME WHILE RAISING POWER TO THE SPECIFIED CALIBRATION LEVEL.
HOLDING THE RAISE BUTTON IN CAN RESULT IN LARGE POWER
OVERSHOOTS THAT COULD DAMAGE THE PA MODULES. ADJUST POWER
SLOWLY BY MAKING DISCRETE BUTTON PRESSES WHILE CLOSELY
MONITORING THE EXTERNAL POWER METER FOR CHANGE. USE THE
DOUBLE UP ARROW GUI ICON TO RAISE POWER IN LARGER STEPS. USE
THE SINGLE ARROW ICON FOR SMALLER STEPS.
STEP 12 LOWPOWERCALIBRATION(10%)‐UsingtheUParrows(GUI)orPowerRaise
(frontpanelbuttons)ontheLPU,increasepowerlevelofthetransmitter
untilthedesiredlevelisindicatedonthepowermeter.RefertoAdjust
OutputPowersubwindowinFigure5‐13onpa
ge5‐23.
a.
Thesmalluparrowboxisforfineincrementsandthelargeboxisforlargersteps.
Itmayalsobenecessarytoutilizethedownarrowboxes.Severaladjustments
maybenecessary.
b. Maintainthedesiredlevelforseveralminutestoallowforthermalsettlingofthe
poweramplifierstages.
c. PresstheSavebuttontostorethecali brationsettingtomemory.
STEP 13
HIGHPOWERCALIBRATION(100%)‐UsingtheUParrows(GUI)orPower
Raise(frontpanelbutton)raisethepowerofthetransmitteruntilthe
desiredlevelisindicatedonthepowermeter.
a.
Thesmalluparrowboxisforfineincrementsandthelargeboxisforlargersteps.
Itmayalsobenecessarytoutilizethedownarrowboxes.Severaladjustmentswill
benecessary.
b. Maintainthedesiredlevelforseveralminutestoallowforthermalsettlingofthe
poweramplifierstages.
c. PresstheSavebuttontostorethecali brationsettingtomemory.
STEP 14
Press“CalibrationComplete”tofinishandexitthecalibrationprocedure.If
youdonotperformthisstep,thecalibrationwillnotbeaccepted.
STEP 15 Preliminarycalibrationprocedurecomplete.ProceedtoFinalAnalogCal
Procedure(Section5.6.2.
2).