-BIT DIGITAL AUDIO SYSTEM MODEL SD-EX200 OPERATION MANUAL SD-EX200_sec TINSZ0523AWZZ
SPECIAL NOTES CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Explanation of Graphical Symbols: - Special Notes - Important Instruction SD-EX200 NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
IMPORTANT SAFETY INSTRUCTIONS 2 Retain Instructions - The safety and operating instructions should be retained for future reference. 3 Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. 4 Follow Instructions - All operating and use instructions should be followed.
IMPORTANT SAFETY INSTRUCTIONS (continued) 15 Outdoor Antenna Grounding - If an outside antenna or cable system 19 Object and Liquid Entry - Never push objects of any kind into this is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.
Contents General Information As an E NERGY S TAR® Partner, SHARP has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. ENERGY STAR® is a U.S. registered mark. WHY PURCHASE E NERGY S TAR® LABELED PRODUCTS? Many Electrical/Electronic Products use energy both when they are on and when they are off. Americans spend more than $3 billion a year on energy consumed by home electronic products when they are not in use.
SD-EX200 Introduction Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. z SD-EX200 1-Bit Digital Audio System consisting of SD-EX200 (main unit) and CP-EX200 (speaker system). Accessories - Introduction / Accessories - General Information Please confirm that the following accessories are included.
Precautions SD-EX200 4" (10 cm) 4" (10 cm) 4" (10 cm) z Use the unit on a firm, level surface free from vibration. z Do not remove the outer cover, as this may result in electric shock. Refer internal service to your local SHARP service facility. z This unit should only be used within the range of 41°F - 95°F (5°C - 35°C). Warning: z Keep the unit away from direct sunlight, strong magnetic fields, excessive dust, humidity and electronic/ electrical equipment (home computers, facsimiles, etc.
SD-EX200 Controls and indicators - Controls and indicators - General Information 1 2 Front panel 3 Reference page 4 5 6 7 8 10 11 12 13 6 7 8 1. CD Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 2. Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 3. Timer Set Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 4. Headphone Jack . . . . . . . . . .
SD-EX200 Left side Side panel Right side 7 Note: For details on opening side covers, see page 12. 8 9 Speaker system Reference page 1 4 1. Tweeter 2. Speaker Grille 3. Woofer 4. Bass Reflex Duct 5. Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - Controls and indicators - 1 2 3 4 5 6 General Information Reference page 1. FM 75 Ohms Antenna Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 13 2. AM Antenna Ground Terminal . .
SD-EX200 Controls and indicators (continued) Remote control Reference page 1 11 12 4 - Controls and indicators - General Information 2 3 5 6 7 8 9 10 13 14 15 16 17 18 1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 2. CD Play/Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 3. CD Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 4. Cursor/Tuner Preset Buttons .
Remote control SD-EX200 Battery installation 1 Remove the battery cover. 2 Insert the supplied batteries according to the direction indicated in the battery compartment. When inserting or removing the batteries, push them toward the nals. 3 battery termi- Test of the remote control Check the remote control after verifying all the connections (see pages 12 - 13). Point the remote control directly at the remote sensor on the unit.
SD-EX200 System connections Speaker connection FM antenna AM loop antenna z Make sure to unplug the AC power cord before connecting the speaker wires. z Connect the speaker wires to the speakers first, then to the unit. This prevents short circuit between and terminals. Connect the wire with the black line to the (-) and the transparent one to the (+).
SD-EX200 Antenna connection Outdoor FM or AM antenna: Use an outdoor FM or AM antenna if you require better reception. Consult your dealer. Supplied FM antenna: Connect the FM antenna wire to the FM 75 OHMS jack and position the FM antenna wire in the direction where the strongest signal can be received. Outdoor FM antenna 75 ohm coaxial cable Supplied AM loop antenna: Connect the AM loop antenna wire to the AM and GND terminals. Position the AM loop antenna for optimum reception.
SD-EX200 General control Volume control Press the VOLUME (+ or -) button to increase or decrease the volume. 0 1 2 ..... 39 40 Bass control Press the BASS/TREBLE button to select "BASS". Within 3 seconds, press the VOLUME (+ or -) button to adjust the bass. -5 - General control - Preparation for Use 1 2 +5 Treble control 1 2 To turn the power on Press the BASS/TREBLE button to select "TREBLE". Within 3 seconds, press the VOLUME (+ or -) button to adjust the treble.
Setting the clock By setting the unit to the correct time, you can use it not only as a clock but also for timer playback. SD-EX200 5 Press the CURSOR ( or ) button to adjust the hour and then press the ENTER button. z Press the CURSOR ( or ) button once to advance the time by 1 hour. Hold it down to advance continuously. z When the 12-hour display is selected, "AM" will change automatically to "PM". z Press the CURSOR ( or ) button once to advance the time by 1 minute.
SD-EX200 Listening to a CD This system can also play audio CD-R and CD-RW discs, but cannot record. Some audio CD-R and CD-RW discs may not be playable due to the state of disc or the device that was used for recording. 1 2 3 4 Press the ON/STAND-BY button to turn the power on. Press the button. Press the button to open the CD cover. Place a CD on the spindle. z Face the label side toward you. z Place a CD on the spindle properly to avoid scratches.
Advanced CD Playback To remove the CD 1 2 3 While in the stop mode, press the button. Press the CD eject button and remove the CD. Press the button to close the CD cover. SD-EX200 To locate the beginning of a track To move to the beginning of the next track: Press the button during playback. z You can skip to any track by pressing the track number appears. button repeatedly until the desired To restart the track being played: Press the button during playback.
SD-EX200 Advanced CD Playback (continued) Direct play Repeat or random play By using the direct buttons, the desired tracks can be played. You can select one of the CD playback mode; "Repeat play", "Random play" and "Normal play". Press the direct buttons to select the desired track. The direct buttons will allow you to select and play any track from 1 to 10 automatically. 1 When in the CD mode, press the PLAY MODE button repeatedly to select the playback mode.
SD-EX200 Programmed play Adding tracks to the program: You can choose up to 20 selections for playback in the order you like. 1 2 Press the button. Press the MEMORY button to enter the programming save mode. If a program has been previously stored, the "MEMORY" indicator will be displayed. Then follow steps 1 - 5 to add tracks. The new tracks will be stored after the last track of the original program.
SD-EX200 Listening to the radio Manual or Auto tuning 1 2 Press the ON/STAND-BY button to turn the power on. Press the TUNER (BAND) button repeatedly to select the desired frequency band. FM stereo 3 Press the TUNING ( FM monaural or ) button to tune in to the desired station. Radio You can tune in to the desired station by pressing the remote control.
SD-EX200 To receive an FM stereo transmission: Press the TUNER (BAND) button to display the "ST" indicator. z " " will appear when an FM broadcast is in stereo. FM stereo mode indicator To recall a memorized station This may be operated only with the remote control. To select a preset station with the TUNER PRESET buttons: Press the TUNER PRESET ( or ) button to select the desired station.
SD-EX200 Timer and sleep operation This may be operated only with the remote control. Timer playback: The unit turns on and plays the desired source (CD, tuner) at the preset time. Sleep operation: Timer playback 1 Press the ON/STAND-BY button to turn the power on. 2 Press the TIMER button. The radio and compact disc player can be turned off automatically. Before setting timer: 2 3 - Timer and sleep operation - Advanced Features 1 Set the unit to the correct time (page 15).
SD-EX200 10Press the ENTER button. When you select the tuner, select a station by pressing the CURSOR ( or ) button, and then press the ENTER button. If a station has not been programmed, "NO P-SET" will appear. 11Press the CURSOR ( or ) button to adjust the volume. Be careful not to turn the volume up too high. 12Press the ENTER button. Reusing the memorized timer setting: The timer setting will be memorized once it is entered. To reuse the same setting, perform the following operations.
SD-EX200 Timer and sleep operation (continued) Sleep operation To confirm the remaining sleep time: - Timer and sleep operation - Advanced Features The radio and CD can be turned off automatically. 1 Press the TIMER button while the sleep timer is set. 2 Within 10 seconds, press the CURSOR ( or ) button to select "SLEEP". 1 2 3 Play back the desired sound source. Within 10 seconds, press the CURSOR ( or ) button to select "SLEEP". z The remaining sleep time is displayed for about 10 seconds.
Enhancing your system z The connection cord is not included. Purchase a commercially available cord as shown below. z Before connecting external units, set this unit to the power stand-by mode and turn off the power to the external units. White SD-EX200 Listening to the playback sounds from VCR, DVD, etc. 1 Use a connection cord to connect the VCR, DVD, etc. to the AUX INPUT jacks. When using video equipment, connect the audio output to this unit and the video output to a television.
SD-EX200 Troubleshooting chart Many potential problems can be resolved by the owner without calling a service technician. If something is wrong with this product, check the following before calling your authorized SHARP dealer or service center. General Symptom z When a button is pressed, the unit z Set this unit to the power stand-by mode does not respond. and then turn it back on. References - Troubleshooting chart - z If the unit still malfunctions, reset it. (Refer to page 27.
SD-EX200 If trouble occurs Before transporting the unit When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is operated incorrectly, it may malfunction. Carrying the unit with a CD inside can cause damage to the unit or the CD. Please open the CD cover to check the CD compartment is empty before transportation. (Refer to page 17.
SD-EX200 Maintenance Error messages Cleaning the CD pickup lens Poor performance during CD playback (skipping or jumping) can be caused by a dirty or contaminated CD laser pickup lens, in this case cleaning may be required. Clean the lens gently with a dry cotton swab taking care not to touch the lens with your fingers. Error messages NO DISC References z The disc is damaged. Remedy z Replace it with another disc. z Eusure that the CD is correctly inserted with the label side toward you.
Specifications SD-EX200 CD player Type 1-disc vertical type compact disc player Signal readout Non-contact, 3-beam semiconductor laser pickup D/A converter 24-bit/96 k D/A converter AC 120 V, 60 Hz Frequency response 20 - 20,000 Hz Power consumption 76 W Dynamic range 101 dB (1 kHz) Dimensions Width: 15"(380 mm) Height: 7-7/8"(200 mm) Depth: 4-3/4"(120 mm) Weight 7.5 lbs. (3.4 kg) Output terminals Speakers: 4 ohms Power source Tuner Frequency range FM: 87.5 - 108 MHz AM: 530 - 1.
CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
