MODEL SF-1116 SF-1118 ELECTROSTATIC COPYING MACHINE OPERATION MANUAL •GETTING STARTED •MAKING COPIES • STATUS INDICATORS •GENERAL INFORMATION •OPTIONAL EQUIPMENT Page 2 8 21 26 47
In some areas, the “POWER” switch positions are marked “I” and “ ” on the copier instead of “ON” and “OFF”. The symbol “ ” denotes the copier is not completely de-energized but in a stand-by condition at this “POWER” switch position. If your copier is so marked, please read “I” for “ON” and “ ” for “OFF”. Caution! For a complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible.
CONTENTS Page 2 2 3 6 GETTING STARTED AUDITING ACCOUNTS ........................ 8 NORMAL COPYING ........................... 9 REDUCTION/ENLARGEMENT/ZOOM ............. 11 DUAL PAGE COPYING ....................... 13 MARGIN SHIFT ............................. 14 EDGE ERASE ............................... 15 SPECIAL PAPERS (manual feed) ................ 16 TWO-SIDED COPYING ........................ 17 INTERRUPTING A COPY RUN .................. 18 AUTOMATIC EXPOSURE ADJUSTMENT ..........
GETTING STARTED Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. A word on copier installation/Cautions A WORD ON COPIER INSTALLATION 2. Do not install the copier in areas that are: ● damp or humid, ● exposed to direct sunlight, ● extremely dusty, ● poorly ventilated, ● subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater. 1.
GETTING STARTED LOADING COPY PAPER 1 Gently lift and pull out the paper tray. 2 Fan the copy paper and insert it into the tray. Maximum height line 3 Loading copy paper To save space, this copier has been designed with an adjustable frontloading tray, which is easily opened for paper loading. For best results, use only Sharp recommended paper. (See page 43.
LOADING COPY PAPER GETTING STARTED Loading copy paper Changing the copy paper size in the tray Lever 1 Gently lift and pull out the paper tray until it stops. 2 Squeeze the lock lever of the front guide and slide the front guide to match the width of the paper. 3 Move the left guide to the appropriate slot as marked on the tray.
LOADING COPY PAPER GETTING STARTED Loading copy paper 7 To set the selected paper size, press and hold the TRAY SELECT ( ) key for more than 5 seconds until all the alarm indicators* blink and “– –” appears in the copy quantity display. * The alarm indicators are the indicators. , , , , and ZOOM A3 A4 A4 R A5 B4 1 8 / 2 ✕ 13 EXTRA A5 A3 200% A4 A3 , A5 A4 141% A4 B4 122% B4 A3 115% 8 Use the copy ratio selector ( the paper size which is set.
GETTING STARTED ADDING TONER Adding toner The toner required ( ) indicator will light up when toner concentration level in the developer unit is low. Please read on to determine when toner must be added. If copying is continued while the indicator is lit, copies will gradually become lighter until the copier stops and the indicator begins blinking. The indicator may also begin blinking during long copy runs of multiple dark originals, even though toner is left.
ADDING TONER GETTING STARTED 5 Pour the toner evenly into the toner hopper. 6 Close the toner hopper cover. 7 Slide the developer unit into the copier. 8 Return the developer unit lock lever into place. 9 Close the front cover. Adding toner 4 Open the toner hopper cover.
AUDITING ACCOUNTS If this copier has been programmed in the auditing mode, it will not function until an assigned 3-digit account number has been entered. See page 33 for setting the auditing mode. MAKING COPIES % If the copier has been programmed in the auditing mode, “–––” will appear in the copy quantity display in the initial conditions. % % % Auditing accounts % % ZOOM % % 1 2 3 4 5 7 8 0/ 1 Enter your account number using the 10-key pad.
NORMAL COPYING 1 Turn the power switch on. ● ● 2 Place the original face down on the document glass. Align it with the original size scale. ● A3 A4 A4 R A5 B4 81/ 2 ✕ 13 Image loss (max. 4 mm (5/32")) can occur at the leading and trailing edges of the copies. 3 Close the document cover. 4 Ensure that the copy paper size in the paper tray is the same size as the original.
NORMAL COPYING ● For manual copy density adjustment, press the AUTO/ MANUAL/PHOTO ( / / ) key to select ) and adjust with the LIGHT ( ) and MANUAL ( DARK ( ) keys as desired. ● ) and then adjust with the For photographs, select PHOTO ( ) and DARK ( ) keys as desired. LIGHT ( ● There are 9 exposure steps indicated by 5 indicator lights. (The indicators light up one or two at a time.) Successive pushes of the LIGHT ( ) key will change the indicator lights in the order (3) / (3•2) / (2) / (2•1) / (1).
REDUCTION/ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected with the copy ratio , ) keys and/or the zoom ( , ) keys. selector ( The zoom function enables precise copy ratio selection from 50% to 200% in 1% increments. 141% A4 B4 122% B4 A3 115% 2 Use the copy ratio selector ( , ) keys and the , ) keys to select the desired copy zoom ( ratio.
REDUCTION/ENLARGEMENT/ZOOM MAKING COPIES To verify a zoom setting without changing the zoom ratio, press and hold the copy ratio display ( ) key. When the key is released, the display will return to the copy quantity display. 122% 115% 86% 81% 70% ● ZOOM Reduction/enlargement/zoom % 50% 0 A5 A3 200% A4 A3 , A5 A4 141% A4 B4 122% B4 A3 115% D. To decrease or increase the zoom ratio rapidly, press and hold or key.
DUAL PAGE COPYING The DUAL PAGE COPY feature produces individual copies of two documents placed side by side on the document glass. It is especially useful when copying books and other bound documents. This feature can be used with the EDGE ERASE and MARGIN SHIFT features. ● AUTO Set the page to be copied first on the left part of the document glass. Press the DUAL PAGE COPY ( Dual page copying 2 ) key. ● Check to be sure that the copy paper size in the paper tray is A4 (8-1/2" x 11").
MARGIN SHIFT Original Copy The MARGIN SHIFT feature automatically shifts the text or image to the right to increase the left margin by approximately 9 mm (1/4"). Expanded margin MAKING COPIES 1 Margin is expanded here. Place the original on the document glass and close the document cover. ● If an optional automatic document feeder (ADF) is installed, it can also be used for this feature. Margin shift 2 Press the MARGIN SHIFT ( 3 Check the copy paper size. 4 Set the number of copies.
EDGE ERASE The EDGE ERASE feature erases dark areas from the copy edges to make a neater, cleaner copy. It is especially useful when copying thick documents which might create shadow lines at their edges. A A ● MAKING COPIES 1 Place the original on the document glass and close the document cover. If an optional automatic document feeder (ADF) is installed, it can also be used for this feature. Edge erase 2 Press the EDGE ERASE ( 3 Check the copy paper size. 4 Set the number of copies.
SPECIAL PAPERS (manual feed) The single-sheet manual bypass can be used to feed standard paper, transparency film, label stock, tracing paper and other special purpose papers measuring from A6 to A3 (5-1/2" x 8-1/2" to 11" x 17"). (See page 43.) MAKING COPIES Special papers (manual feed) 1 Place the original on the document glass and close the document cover. 2 Adjust the manual bypass paper guides to the width of the copy paper. 3 Insert a single sheet of paper all the way into the feed slot.
TWO-SIDED COPYING Two-sided copies can be made on this copier using the single-sheet manual bypass or the optional multi bypass feeder (SF-MF15). ● Replace the first original with the second original. Close the document cover. ● 12 The first copy can be made using any of the paper feed stations. Make sure that the first and second originals are oriented in the same way on the document glass. 3 Turn the first copy over without changing its top-bottom orientation and feed it into the manual bypass.
INTERRUPTING A COPY RUN INTERRUPT is used to interrupt a long copy run so that another job can be done. ● Reduction/enlargement/zoom, exposure adjustments, dual page copying, margin shift, and edge erase can be selected during interrupt copying. An optional ADF can be used for interrupt copying. ● Sort, group, and staple sort cannot be selected during interrupt copying. ● INTERRUPT will not function during staple sort copying (when an optional staple sorter is installed).
AUTOMATIC EXPOSURE ADJUSTMENT The automatic exposure level can be adjusted to suit your copying needs. 2 Press and hold the AUTO/MANUAL/PHOTO ( ) key for approximately 5 seconds. / / ) key 1 2 3 4 5 AUTO / / ● ) indicator will go out and the AUTO indicator The PHOTO ( will begin to blink. ● One or two exposure indicators corresponding to the automatic exposure level which has been selected will light up. The factory default setting is level “3”.
TONER SAVE MODE This mode reduces toner consumption by approximately 10% in the automatic and manual exposure modes. Copies will be lighter but still adequate for general use. Selection of this mode does not affect the photo mode. Follow the procedure below for setting the toning level. MAKING COPIES AUTO Toner save mode 1 Press the AUTO/MANUAL/PHOTO ( ) mode. to select the MANUAL ( 2 Press and hold the AUTO/MANUAL/PHOTO ( ) key for approximately 5 seconds.
MISFEED REMOVAL The copier will stop when a misfeed occurs. The ) indicator will blink, and blinking red misfeed ( misfeed location indicators will indicate the approximate misfeed location. After removing the misfed paper, open and close the front cover and ensure that all the misfeed indicators have gone out. If paper is accidentally torn during removal, be sure to remove all pieces. Be careful not to damage the photoconductive drum or the corona wires.
MISFEED REMOVAL Misfeed in the paper tray 1 Open the front cover and press the release lever to open the copier. CAUTION Be sure to open the upper unit slowly and gently, and do not let go of it until it is fully open. STATUS INDICATORS Misfeed removal 22 2 Remove the misfed paper. 3 Push down the upper half of the copier as illustrated to close it. 4 Close the front cover. ● Be careful not to tear the misfed paper during removal. indicator has gone out.
MISFEED REMOVAL Misfeed in the transport area, fusing area and exit area 2 Press the release lever to open the copier. STATUS INDICATORS 1 Open the front cover. CAUTION Be sure to open the upper unit slowly and gently, and do not let go of it until it is fully open. Misfeed removal 3 Carefully remove the misfed paper. ● If the misfed paper is stuck in the fusing area, raise the fusing unit lever and remove the paper. CAUTION The fusing area is hot. Take care in removing paper.
MISFEED REMOVAL STATUS INDICATORS Misfeed removal 24 4 Push down the upper half of the copier as illustrated to close it. 5 Close the front cover. ● Confirm that the ● If an optional sorter is installed, push the sorter back into position. indicator has gone out.
DEVELOPER REQUIRED When the indicator lights up, the developer should be replaced. DEVELOPER REPLACEMENT SHOULD ONLY BE DONE BY AN AUTHORISED SHARP SERVICE TECHNICIAN. Contact your Service Centre as soon as possible. STATUS INDICATORS MAINTENANCE REQUIRED Developer required/ When the indicator lights up or blinks, service by an authorised Sharp Service Technician is required. Contact your Service Centre as soon as possible.
PART NAMES AND FUNCTIONS Overall layout t y r q w u i e o !0 r GENERAL INFORMATION q Document cover Place the original on the document glass and close the document cover before copying starts. y Manual bypass guides Adjust to the width of the copy paper. Part names and functions w Document glass Place the document to be copied here. u Operation panel All copier controls are located here for easy operation. e Exit tray Finished copies are deposited in the exit tray.
PART NAMES AND FUNCTIONS !1 !2 !4 !5 !6 !3 !5 Release lever Press to release the upper half of the copier. !2 Toner hopper Contains toner. !6 Photoconductive drum Copy images are formed on the photoconductive drum. !3 Fusing unit The fusing unit is hot. Exercise care in this area. Accessories Operation manual . . . . . . . . . . . . . . . . . . . . 1 27 Part names and functions !4 Developer unit lock lever Pull down to release the developer unit.
PART NAMES AND FUNCTIONS Operation panel q w r e AUTO t y u A3 A4 A4 R A5 B4 81/ 2 ✕ 13 EXTRA 1 2 3 4 5 !6 !7 !8 q SORTER ( / / ) key and indicators (p. 52) Press to select a sorter mode when an optional sorter or staple sorter is installed. o Copy quantity display Displays the specified copy quantity during the ready condition and displays the copy countdown as copies are made. Also see items @2 and @5. ) key and indicator w DUAL PAGE COPY ( (p.
PART NAMES AND FUNCTIONS i o !0 A5 A3 200% A4 A3 , A5 A4 141% A4 B4 122% B4 A3 115% !1 !3 !2 100% !4 1 2 3 4 5 6 7 8 9 !5 ACC.#-C 86% A3 B4 B4 A4 A4 A5 , A3 A4 81% 70% A3 A5 50% ZOOM CA % 0/ C Inch system i t @0 @1 @2 @3 @6 @5 @4 !8 TRAY SELECT ( ) key (p. 9) Use to manually select a paper tray.
USER PROGRAMS The user programs allow the parameters of certain functions to be set, changed, or cancelled as desired. NOTE: If operation of the user programs by general users (other than the copier manager) causes problems, detach pages 31 to 36 and store them in a safe place. List of user programs This copier has the following user programs. Program No. Program name Description GENERAL INFORMATION User programs 1 Auto clear time Sets the auto clear time.
USER PROGRAMS Setting the user programs 1 ) key for more Press and hold the TRAY SELECT ( than 5 seconds until all the alarm indicators* blink and “– –” appears in the copy quantity display. * The alarm indicators are the indicators. , , , , and ZOOM 1 2 3 4 5 6 7 8 9 2 ● The selected program number will blink in the copy quantity display. ● If a mistake is made in steps 2 to 4, press the clear ( You will return to step 2. ● The program numbers are shown in the table below.
USER PROGRAMS 1 2 3 4 5 6 7 8 9 4 Select the desired parameter using the 10-key pad. ● The entered parameter number will blink on the right side of the copy quantity display. ● The parameters are shown in the table below. For example, to change the setting of the auto clear time to “90 sec.”, press key 3.
USER PROGRAMS Setting for auditing accounts Setting of user programs No. 10 to 15 varies with the program number. For setting of all programs, first follow steps 1 to 3 in “Setting the user programs” on page 31 to select a program. (1. Press the TRAY ) key for more than 5 seconds. 2. Enter a program SELECT ( ) number (10 to 15) using the 10-key pad. 3. Press the print ( button.) Then follow the appropriate instructions for the program. Program No.
USER PROGRAMS Program No. 12: Account number change Program No. 12 is used to change account numbers. When program No. 12 is entered, an account number will appear in the copy quantity display. ● If no account number has been registered, “12E” will appear in the key. You will return to step copy quantity display. Press the 2 on page 31. 1. Use the copy ratio display ( account number to be changed. ● ZOOM % Use the key to advance through the account numbers. 2.
USER PROGRAMS Program No. 14: Number of copies per account Program No. 14 is used to display the total number of copies made against each account number. When program No. 14 is entered, an account number will appear in the copy quantity display. If no account number has been registered, “14E” will appear in the key. You will return to step copy quantity display. Press the 2 on page 31. 1. Use the copy ratio display ( account number.
USER PROGRAMS Program No. 15: Resetting account Program No. 15 is used to reset all accounts or to reset any desired individual accounts. When program No. 15 is entered, “0” will blink on the right side of the copy quantity display. ● If no account number has been registered, “15E” will appear in the key. You will return to step copy quantity display. Press the 2 on page 31. 1 2 3 4 5 6 7 8 9 1. To reset an individual account, press key 0 on the 10-key pad. To reset all accounts, press key 1. 2.
POWER SAVE MODES The copier has two POWER SAVE modes of operation — preheat mode and auto power shut-off mode. The copier will enter a power save mode once the set time has elapsed without any copier operation after the last copy of a run is made or power is turned on. Both of the power save modes can be automatically controlled by the auto power save control function.
POWER SAVE MODES Setting the power save modes The auto power save control function can be enabled or disabled as desired using user program No. 4. If this function is disabled, the time that elapses before the copier enters a power save mode after any operation is made can be set manually. This time is set with user program No. 2 for the preheat mode and user program No. 3 for the auto power shut-off mode. If the auto power save control function is enabled, the settings of user programs No. 2 and No.
USER MAINTENANCE Proper care is essential for clean, sharp copies. Please take a few minutes to regularly clean your copier. Document glass and document cover Stains on the document glass or document cover will also be copied. Wipe the document glass and document cover with a soft, clean cloth. If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents.
COPIER TROUBLE? Problem Solution ● Copier plugged in? Plug the copier into a grounded outlet. ● Power switch ON? Turn the power switch ON. See page 9. Copies are too dark or too light. ● Copy density properly adjusted? See pages 9 and 19. Blank copies. ● Is the original placed face down? Place the original face down on the document glass. ● Paper too heavy? Use copy paper within the specified range. See page 43. ● Paper damp? Replace with dry copy paper.
COPIER TROUBLE? Problem Dust, dirt, smudges appear on copies. Power is on but copying is not possible. Solution ● Document glass or document cover dirty? Clean regularly. See page 39. ● Original smudged or blotchy? Use a clean original. ● Is the indicator on? ● Is the indicator on? Developer is required. Contact your Sharp Service Centre as soon as possible. See page 25. Maintenance is required. Contact your Sharp Service Centre as soon as possible. See page 25.
COPIER TROUBLE? Problem Solution ● steadily lit in the copy Is quantity display? 1. The optional sorter or staple sorter is not latched to the copier. Slide the sorter or staple sorter toward the copier to latch it into place. 2. The stapler cover of the optional staple sorter is open. Close the stapler cover. ● Is the Toner is required. See page 6, ADDING TONER. ● Is the ● Is the front cover firmly closed? Power is on but copying is not possible.
SUPPLIES Types and sizes of copy paper ORDINARY PAPER (15 lbs.) (5-1/2" x 8-1/2") Weight: (21 lbs.) 52 g/m2 (14 lbs.) 104 g/m2 (28 lbs.) (11" x 17") ▲ ▲ 80 g/m2 A3 ▲ 56 g/m2 A6 ▲ (11" x 17") ▲ Weight: (5-1/2" x 8-1/2") Size: ▲ A3 Manual bypass (single sheet feed) ▲ ▲ A5 Size: ● ▲ Automatic feeding from the paper tray ▲ ● 128 g/m2 (34 lbs.) A4 (8-1/2" x 11") is the maximum size for paper weighing from104 to 128 g/m2 (28 to 34 lbs.).
SUPPLIES Genuine supplies statement Standard supplies for this copier that are to be replaced by the user are copy paper, toner, and staple cartridges for an optional staple sorter. For best copying results, be sure to use only Sharp products. The package of Sharp toner has the Genuine Supplies label. GENUINE SUPPLIES Photoconductive drum The SF-1116 and SF-1118 Copiers have advanced process control technology which improves copy quality uniformity.
SPECIFICATIONS SF-1116 SF-1118 Type Desktop Copy system Dry, electrostatic transfer Originals Sheets, bound documents Original sizes Max. A3 (11" x 17") Copy sizes Max. A3 (11" x 17") Min. A6 (5-1/2" x 8-1/2") Image loss: Max. 4 mm (5/32") (leading and trailing edges) Copying speed 16 copies/min. (A4 (8-1/2" x 11")) 13 copies/min. (A4R (8-1/2" x 11"R)) 11 copies/min. (B4 (8-1/2" x 14")) 9 copies/min.
SPECIFICATIONS Overall dimensions (with exit tray) 885 mm (W) x 595 mm (D) (34-27/32" (W) x 23-7/16" (D)) Weight (with document cover) Approx. 41 kg (90.4 lbs.
OPTIONAL EQUIPMENT CONTENTS ● ● ● ● Downloaded from: http://www.usersmanualguide.com/ OPTIONAL EQUIPMENT ● Page SYSTEM CONFIGURATION ......................... 48 AUTOMATIC DOCUMENT FEEDER (SF-A18) ............ 49 ● Part names .................................... 49 ● Specifications .................................. 49 ● Using the ADF .................................. 50 ● Misfeed removal ................................ 51 / 10-BIN SORTER (SF-S17N)/ 10-BIN STAPLE SORTER (SF-S54) ...................
SYSTEM CONFIGURATION A number of options are available for the copier which allow you to configure a copier system to meet your needs. The options include the following. Automatic document feeder (SF-A18) 10-bin sorter (SF-S17N) Multi bypass feeder (SF-MF15) 10-bin staple sorter (SF-S54) Paper tray (SF-UB15) System configuration OPTIONAL EQUIPMENT 48 Downloaded from: http://www.usersmanualguide.
AUTOMATIC DOCUMENT FEEDER (SF-A18) The automatic document feeder (ADF) holds up to 50 originals for automatic feeding. PART NAMES Feeding roller cover Original guides Document feeder tray Document feeder cover Document feeder indicators Document feeder indicators Original feed indicator Indicates the originals in the tray will be fed. Original reminder Specifications Weight: 50 to 128 g/m2 (14 to 34 lbs.
AUTOMATIC DOCUMENT FEEDER (SF-A18) Using the ADF ● ● ● Be sure to remove any staples or paper clips from the originals. Damaged or crumpled originals may misfeed in the document feeder. It is recommended that these originals be copied from the document glass. For best feeding of originals which have binding holes punched into them, insert them so that the holes are positioned to the right or along the side guides.
AUTOMATIC DOCUMENT FEEDER (SF-A18) Misfeed removal An original misfeed may occur at one of three locations: (A) in the feed section, (B) in the exit roller, or (C) under the transport belt. A C B Location A Feeding roller cover (A) Open the feeding roller cover and pull the original gently to the right and out from the document feeder tray. ● Be sure to open and close the document feeder cover to cancel the misfeed location indicator. (B) Gently pull the original out.
10-BIN SORTER (SF-S17N) 10-BIN STAPLE SORTER (SF-S54) The SF-S17N 10-Bin Sorter has two sorter modes for different copying jobs: one sorts copies into sets matching the sequence of the originals and the second groups copies from different originals into separate sort bins. The SF-S54 10-Bin Staple Sorter has, in addition to the above two modes, a STAPLE SORT mode. Sorted copies can be automatically stapled together. The maximum allowable number of copies varies with the selected mode.
10-BIN SORTER (SF-S17N)/10-BIN STAPLE SORTER (SF-S54) Using a sorter SORT GROUP Press the SORTER ( mode. (The STAPLE SORT ( SF-S17N.) / / ) key to select the desired ) mode cannot be selected for the To cancel the mode, press the SORTER ( until the SORT ( ), STAPLE SORT ( ( ) indicators all go out. / / ) key ), and GROUP NON-SORT mode When none of the three sorter modes, SORT ( ), STAPLE SORT ( ) or GROUP( ) is selected, the copier is in the NONSORT mode.
10-BIN SORTER (SF-S17N)/10-BIN STAPLE SORTER (SF-S54) SORTER CAPACITIES SF-S17N SF-S54 Top bin 100 sheets in the NON-SORT mode Sort bins SORT mode: Paper size A5, A4, A4R (5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R) B4, A3 (8-1/2" x 14", 11" x 17") Sort bins SORT or STAPLE SORT mode: Bin capacity Paper size (max.) Bin capacity (max.
10-BIN STAPLE SORTER (SF-S54) Staple sort (SF-S54) The STAPLE SORT ( ) mode staples copies of A5, A4, A4R, B4, and A3 (5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 14", and 11" x 17") sizes. ● In some areas, 8-1/2" x 13" size copies can be stapled. Using the document glass 1 Stapling location 2 2 3 4 5 6 7 8 9 0/ ● Copy from the last page to the first page.
10-BIN STAPLE SORTER (SF-S54) Using the ADF 1 Stapling location Set the originals in the document feeder tray face up with the stapling position in the upper left corner. ● 2 Press the SORTER ( STAPLE SORT ( ● 10-bin staple sorter (SF-S54) 1 2 3 4 5 6 7 8 9 0/ A / / ) mode. OPTIONAL EQUIPMENT 3 4 Press the print ( ● ) key to select the Make sure that there is no paper in any sort bin before selecting ) mode. the STAPLE SORT ( Set the number of copies. Up to 10 sets can be made.
10-BIN STAPLE SORTER (SF-S54) Staple cartridge replacement/staple jam removal (SF-S54) When the staple cartridge is empty or staples become jammed in the ) mode indicator STAPLE SORT mode, the STAPLE SORT ( will blink, the misfeed location indicator for the sorter will blink, and the red manual staple key indicator on the staple sorter will light up. NOTES: ● If the staple cartridge is empty or only a few staples are left, replace the cartridge with a new one following the procedure below.
10-BIN STAPLE SORTER (SF-S54) Staple jam removal 10-bin staple sorter (SF-S54) OPTIONAL EQUIPMENT 58 1 Open the stapler cover. 2 Close the stapler cover. 3 Remove all copies from the bins of the staple sorter. ● ● Jammed staples will be removed automatically. To check that the stapler works properly, copy an original and staple it.
10-BIN SORTER (SF-S17N) Misfeed removal The copier will stop when a misfeed occurs. The misfeed ( ) indicator will blink and blinking red misfeed location indicators will indicate the approximate misfeed location. SF-S17N 10-bin sorter 2 Remove the misfed paper from the sorter or from the exit area of the copier. 3 Slide the sorter back toward the copier and latch it into place.
10-BIN STAPLE SORTER (SF-S54) SF-S54 10-bin staple sorter 2 Remove the misfed paper from the staple sorter or from the exit area of the copier. 3 Slide the staple sorter back toward the copier and latch it into place. 4 Open and close the front cover to cancel the 10-bin staple sorter (SF-S54) 1 Pull the sorter lock lever and carefully slide the staple sorter away from the copier. OPTIONAL EQUIPMENT 60 ● indicator.
10-BIN SORTER (SF-S17N)/10-BIN STAPLE SORTER (SF-S54) Specifications SF-S17N No. of bins 10 Bin capacity NON-SORT: 100 sheets (top bin) SORT: 30 sheets (A5, A4, A4R (5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R)) 15 sheets (B4, A3 (8-1/2" x 14", 11" x 17")) GROUP: 20 sheets (A5, A4, A4R (5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R)) 15 sheets (B4, A3 (8-1/2" x 14", 11" x 17")) Paper size Top bin: Sort bins: Max. Min. Max. Min.
MULTI BYPASS FEEDER (SF-MF15) The multi bypass feeder automatically feeds up to 50 sheets of standard copy paper. Paper guides Specifications Multi bypass feeder (SF-MF15) Acceptable copy paper (Automatic feed) Weight: 56 to 80 g/m2 (15 to 21 lbs.) Size: A6 to A3 (5-1/2" x 8-1/2" to 11" x 17") Capacity: Up to 50 sheets, provided the total aggregate thickness does not exceed 5 mm (3/16") OPTIONAL EQUIPMENT (Single sheet feed) Weight: 52 to 128 g/m2 (14 to 34 lbs.
MULTI BYPASS FEEDER (SF-MF15) Using the multi bypass feeder 1 Unfold the multi bypass feeder. ● When feeding A4R, B4, or A3 (8-1/2" x 11"R, 8-1/2" x 14", or 11" x 17") sized paper, extend the feeder tray. Insert the copy paper all the way into the multi bypass feeder. A6 sized paper must be fed narrow side into the feed slot. ● Up to 50 sheets of standard copy paper measuring from A6 to A3 (5-1/2" x 8-1/2" to 11" x 17") can be loaded in the multi bypass feeder.
MULTI BYPASS FEEDER (SF-MF15) A3 A4 A4 R A5 B4 81/ 2 ✕ 13 4 Press the TRAY SELECT ( 5 Leave the copy quantity at 0 if using special papers. Set the number of copies if using standard copy paper. 6 Press the print ( ) key to select the bypass. EXTRA C Multi bypass feeder (SF-MF15) AC OPTIONAL EQUIPMENT 64 ● ) button.
PAPER TRAY (SF-UB15) The paper tray in the copier can be replaced with an optional paper tray. To replace the paper tray, follow the procedure below. To load copy paper into the paper tray, see page 3, LOADING COPY PAPER. 2 Gently lift and remove the paper tray. 3 Insert the new paper tray at an angle, as shown. 4 Push the paper tray firmly back into the copier. 5 Use the procedure described on page 5 to set the copy paper size.
MEMO OPTIONAL EQUIPMENT 66 Downloaded from: http://www.usersmanualguide.
MEMO OPTIONAL EQUIPMENT Downloaded from: http://www.usersmanualguide.
MEMO OPTIONAL EQUIPMENT 68 Downloaded from: http://www.usersmanualguide.
Required in IEC-950 (EN 60 950) - Europe • The equipment should be installed near an accessible socket outlet for easy disconnection. Required in Appendix ZB of BS 7002 (En 60 950) — United Kingdom MAINS PLUG WIRING INSTRUCTIONS The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable (moulded) or a rewireable type.
SF-1116/SF-1118 SHARP CORPORATION PRINTED IN JAPAN 97K KS➀ TINSE1653 FCZZ Downloaded from: http://www.usersmanualguide.
