User manual

8
Contents/Precautions
SH-01H_E_01.fm
[8/12]
TV/Mobacas antenna cable SH01
SH-01H is waterproof/dustproof, however, do not allow
foreign object such as liquid or dust to get inside the
handset and do not allow foreign object such as liquid or
dust to adhere to accessories or optional parts.
The adapter, docomo nano UIM card and TV/Mobacas antenna cable
are not waterproof/dustproof. Do not use in humid or steamy areas
such as bathrooms and avoid exposing to rain and other forms of
moisture. If they are carried close to the skin, perspiration may cause
internal components to corrode and result in malfunction. Note that if
a problem is found to be due to moisture, the handset and parts are
not covered by warranty and in some cases may be irreparable. Even
when repairs are possible, repair charges will be incurred, since the
damage is not covered by warranty.
Clean only with a soft and dry cloth (such as the type used
for eyeglasses).
･ Forceful rubbing of the display with a dry cloth etc. may scratch its
surface.
･ Water drops, dirt, etc. left on the display may cause stains to form
on its surface.
･ Never use chemicals such as alcohol, thinners, benzene or
detergents, as these agents may erase the printing or cause
discoloration.
Occasionally clean terminals with a dry cotton swab etc.
Dirty terminals may result in poor connections and loss of power or
insufficient battery charge. Keep the terminals clean with a dry cotton
swab etc.
Be careful with the terminals while cleaning them.
Do not place the equipment near an air conditioning vent.
Condensation formed due to rapid changes in temperature may
cause internal corrosion and lead to a malfunction.
Do not apply excessive force on the handset etc. when
using it.
Carrying the equipment in a tightly packed bag or sitting on it put in
your pocket may cause damage to the display, internal components,
etc. or result in a malfunction.
Keeping an external connector device plugged into the external
connector terminal or earphone/microphone terminal may cause
damage or a malfunction.
Do not rub or scratch the display with metal etc.
May scratch it and cause a malfunction or damage.
Read the respective user's guides supplied with supported
optional parts carefully.
Do not forcefully press the surface of the touch panel or
operate with a pointed object such as a fingernail, ballpoint
pen or pin.
May damage the touch panel.
Avoid using the handset in extremely high or low
temperatures.
Use the handset within the range of a temperature between 5°C and
35°C and a humidity between 45% and 85%.
Using the handset close to land-line phones, TVs, radios,
etc. may have harmful effects on the operation of such
equipment. Move as far away as possible from such items
before use.
Keep a separate memo noting information stored on the
handset.
DOCOMO shall not be liable for any loss of content.
Do not drop or otherwise subject the handset to severe
impact.
May cause a malfunction or damage.
Sides Aluminum/Anodizing
Grip sensor Acryl
Incoming/Charging lamp
PC resin/UV coating for
surface, Deposition
Back
Reinforced glass/Printing on
the back
Surrounding area of back
PA resin/UV coating for
surface
docomo nano UIM card slot SUS/Ni plating
microSD Card slot SUS/Ni plating
docomo nano UIM card/microSD
Card slot cover
PC resin/UV coating for
surface, Deposition
Gasket of docomo nano UIM
card/microSD Card slot cover
Silicon rubber, SUS
Tray for inserting docomo nano
UIM card
POM resin
IMEI plate PET resin
Surrounding area of earphone/
microphone terminal
PC resin
Power key Aluminum/Anodizing
Side key Aluminum/Anodizing
Camera panel
Reinforced glass/Printing on
the back
Decoration of camera Aluminum/Anodizing
Fingerprint sensor Polyimide/UV coating
Decoration of fingerprint sensor Aluminum/Anodizing
External connector terminal
SUS/Sn plating, Copper alloy/
Gold plating
Part Material/Surface treatment
Earphone/Microphone terminal
(Resin section)
Styrene system elastomer
Earphone/Microphone terminal
(Metal section)
Ni base, Brass/Gold plating
Cord Olefin system elastomer
Connector Styrene system elastomer
Connector (Connection) POM resin
Plug (Metal section) Ni base, Brass/Gold plating
Plug (Resin section) PP resin
Part Material/Surface treatment
Handling precautions
General notes
Notes about the handset
SH-01H_E.book 8 ページ ２０１５年１０月３０日 金曜日 午後４時２２分