SJ-PV50H-G SJ-PV50H-W " イラスト AM PM !
$ * 2 , ! 3 4 5 6 ( # - 8 10 11 12 ) ! $ $ 14 $ % & 16 18 The "indirect" cooling method of the cooling panel gently cools foods in a "wrapping" manner rather than cooling directly.
* + , ) / # ! - -
( ' & ・$ $ $
Installation Select a location.
) ! * If soapy water is used, wipe it off thoroughly. !!" # !$"% The interior compartments of the refrigerator may become hot when transporting in the case of hot weather. Electronic tones will sound when turning on the power with the doors open.
! " FU #* ' #$ % & '( - * + , E LIN & )! $ " &
Refrigerator compartment Cooling panel Refrigerator light Temperature sensor Small pocket Shelf Bottle pocket (left) Small pocket Three position adjustable shelf Egg pocket Egg holder (ten eggs storeable) ※Always place in the egg pocket. Bottle pocket (right) When there are no eggs turn the case around to store small foods. Bottle guard Prevents bottles, Chilled case (left) Chilled case (right) etc. from falling. Stick-type food products can also be stored inside.
Freezer compartment Stainless tray Freezer case (top) Freezer case (bottom) STORING FOOD FOR BEST FREEZING Quality of foods should be fresh. Freeze small quantities of food at a time to freeze them quickly. Food should be properly stored or covered and the air should be removed to seal tightly. Evenly place the food in the freezer. Label bags or containers to keep an inventory of freezing food. Notes Do not touch the freezer compartment with wet hands. Do not place foods higher than the cases.
% % % &' "( $ $ % ! " # ) " $
$ " # " # $ % & !
■ Do not use (heat-resistance: 60¡C), (clogging of purifier filter and dirtying of interior may result). Malfunction of the ice maker may occur as a result. ■ ■ This may cause the automatic ice maker to malfunction (damage of the detection lever, etc.) or the case from being able to be pulled out.
Mounting and removing accompanying parts Pockets Top filter Removing 1 Remove cover. the filter 2 Pull and remove the top filter. Hold the front end and pull up. Top filter up from the Mounting Insert in the tabs. Removing Pull bottom side. Mounting Mount the top filter on the filter cover and insert in the top surface of the refrigerator.
! # 1 2 " 1 " 2 " $ 3
・ .
Notes Do not use polishing powder, benzine, hot water etc. If undiluted detergent is used or soapy water is not wiped off thoroughly, cracking of plastic parts can result. About the stainless tray Salt adhered on the tray may cause rusting. In this case, clean the tray with kitchen detergent (cream-type cleanser, etc.) as quickly as possible. Do not use nylon scrubbing brushes. The tray may become scratched.
0 ! 1 " When using bleach, be sure to follow the accompanied directions. % " * Remove the , $ * , and - Pull up straight.
What to do Power outage During a power outage Moving / Transporting After power turns back on… The LCD panel will be restored to its factory settings.
Move refrigerator away from the heat source and reinstall in a place away from direct sunlight and in a well-ventilated and cool location. 5 Space is required for releasing heat. 5 Space out foods.
■ ■ ! " # The amount of ozone is minimal and is not harmful to the human body. In addition it decomposes quickly and does not accumulate. $ Remove and wash with water.
Using the LCD panel Contents Overview of the LCD panel 23 Time Setting 24 Timer 25 Rapid Ice Making 26 Rapid Freeze 26 Refrigerator Temp 27 Freezer Temp 27 Plasmacluster OUT 28 Illumination 29 Plasmacluster IN 29 Night Mode 30 Vacation Mode 30 Auto Ice Maker 31 Ice Tray Cleaning 32 Backlight Auto-off 34 Key Lock 34 Operation Tones 35
( ( ) ! * " ・$ % ! & ' ! $ ! .
Time Setting ・ When the power outage or the power plug has been removed, start from step 3. the minutes using the dial. 5 Set the "Time Setting" 1 Select mark. → → → → AM 2 Press "CHOOSE/START". AM 6 Press "CHOOSE/START".
・-! $ ..
・ ( ) * ' !" #$ %& % / !" #$ %& % / , - ・The room temperature is high. The door is frequently opened. ・Many food products are stored・Refrigerator is defrosting ・Immediately after setting automatic ice making from OFF to ON. % , + .
& ! ' ( ) ) ' * ! " # !
!"# "$!%# & ■ Cluster ions are generated from water molecules (H20) and oxygen molecules (O2) within the air. There are not parts to be replaced periodically.
Illumination Plasmacluster IN Operation will start when the power of the refrigerator is turned on. 1 Select the "Illumination" mark. the "Plasmacluster IN" 1 Select mark. 2 Press "CHOOSE/START". 2 Press "CHOOSE/START". Beep 3 Select ON using the dial. 3 To cancel operation Beep Select OFF using the dial. To start operation 4 Press "CHOOSE/START". Beep 4 Press "CHOOSE/START". Beep Notes Setting cannot be performed when Plasmacluster OUT is set to OFF.
- ・ ( ) " ' ・.
) **+ ・% ( . % ( * , * ( - ( % ( * * . .
Ice Tray Cleaning ・Use this feature when cleaning the ice tray (or pipe) the water tank with water 1 Fill and set into the tank. (When not using the refrigerator for some time) 5 Press "CHOOSE/START". Beep The temperature display bar will move and operation will start. Operation requires about 40 seconds. the "Ice Tray Cleaning" 2 Select mark. The end tone (beep) will sound and the display will return to the OFF screen. 3 Press "CHOOSE/START". 4 Select ON using the dial.
・. , (When not using the refrigerator for some time or when moving the refrigerator) % !! " #$ / The temperature display bar will move and operation will start. ! ' ( ) The end tone (beep) will sound and the display will return to the OFF screen.
% & ' ( # ) # " ) # ** ! % & ( # ' + ( # # , $ , $ - ( .
, &' ( ) * + ' $ !" # !" Select ON.
! " # $ ! % $ & $ $ ' ( $) $ ! * ! !! *) 1
