Brochure

• Dimensions that are shown in Figures 2
and 3 (for 24") or Figure 1 (for 30") must
be used. Dimensions provide minimum
clearance. Locate electrical outlet in the
shaded area in the upper le-hand corner
of the cutout.
• Contact surface must be solid and
level. The oor of the opening should be
plywood and strong enough to support
the weight of the oven (min. 100 pounds).
• Check installation location for proper
electrical supply.
• Your microwave drawer oven can be built
into a cabinet or wall by itself or under a
wall oven.
• Be sure that the clearance of the oor
between the wall oven and the
microwave drawer oven is a minimum of
2-inches.
• The microwave drawer oven will easily t a
9" x 13" oblong dish or a bag of microwave
popcorn.
• The microwave drawer oven can also be
mounted ush. Please see instructions for
ush mounting included with the Flush
Mount Deector vent.
30" MICROWAVE DRAWER OVEN MEASUREMENTS
CLEARANCES AND DIMENSIONS
24" MICROWAVE DRAWER OVEN MEASUREMENTS
Figure 1 Contains many microwave drawer
oven measurements for reference when
planning the drawer's location. This microwave
drawer oven can be installed below any
electric or gas wall oven.*
Cutout Dimension 28 7/16" x 15 9/16
A. 6"
B. Suggested electrical
outlet location*
C. Anti-Tip block
D. 5"
E. 3-1/2"
F. 4"
G. 22-1/8" opening
H. 14-13/16" to bottom
of Anti-Tip block
I. 7/8" overlap
J. 23-1/2" min. depth
K. 3/16" overlap
L. 36" countertop height
M. Allow 7/16" min. space
N. Floor (100 lbs support)
O. 24" cabinet minimum
P. 15-9/16" opening
Q. Allow 1/8" overlap
A. 21-5/8"
B. 4-11/16"
C. 1-3/4"
D. 21-7/8"
E. 23-7/8"
F. 15-7/8"
G. 14-19/32"
H. 1-9/64"
door thick
I. 15" drawer
opening
J. 4"
FIGURE 2.
FIGURE 3.
Figures 2 and 3 Contain many microwave drawer oven
measurements for reference when planning the drawer's
location. This microwave drawer oven can be installed
below any electric or gas wall oven.*
IMPORTANT Always allow sucient power cord length
to the electrical outlet to prevent tension. Always check
electrical codes for requirements.
FIGURE 1.
Cutout Dimension 28 7/16” x 15 9/16”
BUILDER’S GUIDE, SPEC SHEET AND INSTALLATION MANUALS
ARE AVAILABLE FOR DOWNLOAD AT WWW.SHARPUSA.COM
SHARP 24" 1.2 CU. FT 950W STAINLESS STEEL IoT EASYWAVE OPEN MICROWAVE DRAWER OVEN
24 IN. 1.2 CU. FT. 950W SHARP BLACK
STAINLESS STEEL MICROWAVE DRAWER OVEN
24 IN. 1.2 CU. FT. 950W SHARP STAINLESS
STEEL MICROWAVE DRAWER OVEN
*ALSO AVAILABLE IN 30 IN.
IMPORTANT Always allow sucient power
cord length to the electrical outlet to prevent
tension. Always check electrical codes for
requirements.
*Can also be installed using an electrical outlet in an adjacent cabinet
within the area where the provided electrical cord can reach. Power
cord access hole in cabinet should be at least 1 1/2” diameter and
deburred of all sharp edges.
A. 84" wall cabinet
B. Optional wall oven
cutout
C. Suggested
electrical outlet
location*
D. 6"
E. Anti-Tip block
F. 3-1/2"
G. 5"
H. 4"
I. 2" minimum
J. 22-1/8" minimum,
28-7/16" maximum
K. Allow 3/16" overlap
L. 14-13/16" to bottom
of Anti-Tip block
M. Allow 23/32" overlap
N. 23-1/2" minimum
depth
O. 15-9/16" opening
P. Allow 1/8" overlap
Q. Floor must support
100 lb
R. 30" cabinet minimum
CONVENIENCE YOU
CAN COUNT ON
The concealed, glass, Touch Control panel is easy-to-
see and operate at a convenient 45° angle, keeping
all of the controls at your ngertips when you need
them, and completely out of sight when you don’t.
The modern, edge-to-edge, black glass and stainless
steel design with bright, LED interior lighting and stylish
oor pattern compliments your kitchen and pairs
beautifully with other stainless steel appliances.
THE SHARP IoT MICROWAVE DRAWER OVEN
WITH EASY WAVE OPEN