SKCD24U0GS Installation Guide

ManualsBrandsSharp ManualsSingle Wall OvensSharp SuperSteam+ 24" Stainless Steel Built-In Single Wall Oven

Sharp Convection Microwave Drawer & SuperSteam+ Pedestal

Model SKCD24U0GS

For use with models SMD2499FS AND SSC2489DS.

IMPORTANT NOTES TO THE INSTALLER

• PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION.

• Observe all governing codes, ordinances, and safety instructions.

• Refertothesespecicmodels'installationinstructionsformoreinformationonplacement.

• Be sure to leave these instructions with the consumer.

• Remove all packing material before beginning the installation.

NOTE:

This installation process requires two people. Please ensure you have another person to help lift and install the unit.

WARNING:

Follow all of the steps provided in this installation. Improperly securing or installing the unit can lead to possible injury or

damage to the unit.

INSTALLATION INSTRUCTIONS

ITEM PART NAME QTY

PRICE

CODE

UTC PEDESTAL

DPED-B002MRK0

1 N/A

MOUNTING CLEATS

SPAK-B128MRE0

2 AK

MOUNTING CLEAT SCREWS

XMSS742P38000

4 AA

TOE KICK

GCOVHB087MRT0

1 AT

TOE KICK SCREWS

XUPS840P12X00

2 AA

DRAWER MATS

PCOV-B009MRE0A

2 AN

SCREW LEVELING

GLEGPB006MRE0

4 AC

DRAWER DECORATION

HDECAC157MRP0

2 BB

SUPERSTEAM OVEN CONVERSION

BRACKET

LANGTB464MRP0

2 AP

SUPERSTEAM OVEN CONVERSION

BRACKET SCREWS

LX-BZA148WREZ

2 AA

Items B-J are available for ordering.

I J

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Sharp Convection Microwave Drawer & SuperSteam+ Pedestal Model SKCD24U0GS For use with models SMD2499FS AND SSC2489DS. IMPORTANT NOTES TO THE INSTALLER • PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION. • Observe all governing codes, ordinances, and safety instructions. • Refer to these specific models' installation instructions for more information on placement. • Be sure to leave these instructions with the consumer.
PAGE 2
INSTALLATION INSTRUCTIONS 1. Cabinet cutout dimensions. Prepare the cabinet opening as shown in Figure 1. Overall Dimensions 23 1/2" (596.9 MM) Height (A) 34 1/2" (876 mm) 23 13/16" (604.8 MM) Width (B) 24" (610 mm) SUGGESTED ELECTRICAL OUTLET LOCATION 14 7/16" (366.7 MM) MIN 15 3/4" (390.5 MM) MAX *NOTE: INSTALLER PROVIDE TOP FILLER IF NEEDED A Inside Drawer Dimensions C B 21 13/16" (554.0 MM) FIGURE 1 18 11/16" (474.7 MM) 23 11/16" (601.7 MM) 2 Depth (C) 23 1/2" min.
PAGE 3
INSTALLATION INSTRUCTIONS 2. Convection Microwave Drawer - Place the oven on a secure surface. Remove the 4 bottom screws (2 on each side of the oven) as shown in Figure 2A. Carefully place the oven on top of the pedestal in-between the mounting rails on the left and right. SuperSteam+ Oven - Place the oven on a secure surface. Remove the 2 bottom screws (1 on each side of the oven) as showing in Figure 2B. Install the two conversion brackets with the two provided screws (J). See Figure 2C.
PAGE 4
INSTALLATION INSTRUCTIONS 3. Align the front face of the oven with the front face of the pedestal drawers. Once positioned, fasten the oven to the pedestal. 4. Adjust the height of the overall unit to fit your specific opening. The pedestal contains 4 adjustable feet. To adjust, have one person tilt the unit to one side while the other person adjusts the 2 feet on the raised side to the desired height. Repeat this step by tilting the unit to the other side and adjusting the other 2 feet.
PAGE 5
INSTALLATION INSTRUCTIONS 7. Slide the unit into the opening. Plug oven into the wall receptacle prior to pushing the unit all the way in. See Figure 8. The mounting angles of the oven should rest against the installed wooden cleats. 6. Install the wooden cleats. Align the bottom of the cleat to the measurement from Step 5. The pedestal can be installed flush or standard with the face of the cabinet. Depending on the preference, the depth of the cleat position should be adjusted as such. See Figure 6.
PAGE 6
INSTALLATION INSTRUCTIONS 8. Open the oven door and pre-drill each hole using a 1/16" (1.6 mm) drill bit. Fasten the unit to the mounting cleats using the 4 mounting screws provided with your oven. See Figure 9A or 9B. 9. Install bottom kickplate. Use the 2 toe kick screws to fasten the plate. The 2 toe kick screws come installed in the unit. Remove these 2 screws prior to positioning the kickplate. See Figure 10.
PAGE 7
CUSTOM PANEL INSTALLATION The pedestal drawer fronts can be replaced with custom wood fronts. If custom drawer faces are preferred, the stainless steel drawer faces can be taken off by removing 5 screws (3 on the back side and 2 underneath). See Figure 11. Suggested custom drawer face dimensions: Height 5" (127 mm) Width 23 11/16" (602 mm) Depth 1 3/16" (30.
PAGE 8
SHARP ELECTRONICS CORPORATION 100 Paragon Drive • Montvale, New Jersey 07645 For any other assistance or information about this kit, please call Sharp’s Customer Assistance Center: 1-800-BE-SHARP (1-800-237-4277) TINSEB584MRR0 Mar 1, 2021