Installation Sheet

ManualsBrandsSharp ManualsDomestic AppliancesSSC3088AS

SPECIAL WARNING

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE THIS INSTALLATION MANUAL FOR LOCAL ELECTRICAL INSPECTOR’S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CLEARANCES AND DIMENSIONS

For SAFETY CONSIDERATIONS do not install oven in any combustible cabinetry which is not in accord with the stated

clearances and dimensions on page 4, Figure 2 or page 7, Figure 7.

SSC3088AS SUPERSTEAM

OVEN

INSTALLATION MANUAL

UNPACKING YOUR OVEN

• Remove all packing materials from inside the oven.

• Check the oven for any damage, such as misaligned or bent oven,

damaged oven seals and sealing surfaces or dents inside the

cavity or on the front side of the oven. If there is any damage,

do not operate the oven and contact your dealer or a SHARP

AUTHORIZED SERVICER.

IMPORTANT NOTES TO THE INSTALLER

• Read all of the Installation Manual before installing the oven.

• Remove all packing material before connecting the electrical

supply.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the consumer.

IMPORTANT NOTES TO THE CONSUMER

Keep this manual with your Operation Manual for future reference.

• As when using any oven generating heat, there are certain safety

precautions you should follow. These are listed in the Operation

Manual. Read all and follow carefully.

• This oven should only be installed and grounded properly by

a qualied installer or service technician.

IMPORTANT SAFETY INSTRUCTIONS

If the information in this manual is not followed

exactly, a re or electrical shock may result that could cause

property damage, personal injury or death.

• This oven must be electrically grounded in accordance with

local codes.

• Do not install this oven if the surrounding wall coverings and

the cabinets cannot withstand the heat generated by the oven.

Never leave children alone or unattended in

the area where a oven is in use.

• Do not use the Oven as a storage space. This creates a

potentially hazardous situation.

TINSKB207MRR2 JaN 8, 2016

Summary of content (10 pages)

PAGE 1
SSC3088AS SUPERSTEAM+ OVEN INSTALLATION MANUAL SPECIAL WARNING INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE THIS INSTALLATION MANUAL FOR LOCAL ELECTRICAL INSPECTOR’S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. CLEARANCES AND DIMENSIONS For SAFETY CONSIDERATIONS do not install oven in any combustible cabinetry which is not in accord with the stated clearances and dimensions on page 4, Figure 2 or page 7, Figure 7.
PAGE 2
INSTALLATION HARDWARE ITEM NAME QTY 1 Left Mounting Bracket 1 LANGTB372MRP0 2 Right Mounting Bracket 1 LANGTB378MRP0 3 Wood Screws 8 XTSS740P20000 4 Mounting Bolts 4 LX-CZB069MRE0 5 Shoulder Bolts 2 LX-CZB068MRE0 6 Shoulder Bolt Sleeves 2 PCOVPB226MRE0 1 2 3 4 5 6 E PART CODE 2
PAGE 3
OVEN MEASUREMENTS 30" (762 mm) 19 7/8" (504.8 mm) 19 1/16" (484.1 mm) 3/4" (19.05 mm) Figure 1A FRONT 1 1/4" (32 mm) BACK 15 21/32" (397.6 mm) 2 1/64" (51.18mm) 16 15/16" (430.
PAGE 4
CLEARANCES AND DIMENSIONS FOR STANDARD SURFACE MOUNT A. B. C. D. E. F. 27 15/16" cutout 18 1/8" cutout* 15 3/4" min. depth 33" min. height 4" 18" * Critical dimension Note: Platform must be able to support 70 lbs.
PAGE 5
INSTALLATION INSTRUCTIONS FOR STANDARD SURFACE MOUNT 1. Mounting brackets should be installed with the 8 wood screws provided, 19 ¼" apart from each other and centered in the cabinet opening. Locate position, center punch and drill pilot hole 1/8". See Figure 3. Front of flange even with front of surface 19 1/4" Note: Platform must be able to support 70 lbs.
PAGE 6
INSTALLATION INSTRUCTIONS FOR STANDARD SURFACE MOUNT 6. Open the drip tray door and insert the 2 shoulder bolts supplied. See Figure 6. Do not completely tighten. Always take caution lifting heavy products. 2. Use a minimum of 2 people to lift and install oven. Place the oven adjacent to the cabinet opening, see Figure 4. Plug the power supply cord into the electrical outlet. 3. Carefully guide the oven between the mounting brackets. Avoid pinching the cord between the oven and the brackets. 4.
PAGE 7
CLEARANCES AND DIMENSIONS FOR FLUSH MOUNT Block added by cabinet installer Steam oven face Block added by cabinet installer Suggested electrical outlet location F A 84" D Cabinet face H I Detail A Top View Note: the mounting surface of the top block must sit 1" back from the face of the cabinet. (allowing the face of the steam oven out 1/4") G C B Platform edge Note: Platform must be able to support 70 lbs.
PAGE 8
INSTALLATION INSTRUCTIONS FOR FLUSH MOUNT 1. Install mounting brackets 19 1/4" with the 8 wood screws provided. Locate position, center punch and drill pilot hole 1/8". See Figure 8. Front of flange even with front of surface of the installed block 19 1/4" *90˚ Note: Platform must be able to support 70 lbs.
PAGE 9
INSTALLATION INSTRUCTIONS FOR FLUSH MOUNT 6. Open the drip tray door and insert the 2 shoulder bolts supplied. See Figure 11. Do not completely tighten. Always take caution lifting heavy products. 2. Use a minimum of 2 people to lift and install oven. Place the oven adjacent to the cabinet opening, see Figure 9. Plug the power supply cord into the electrical outlet. 3. Carefully guide the oven between the mounting brackets. Avoid pinching the cord between the oven and the brackets. 4.
PAGE 10
ELECTRICAL OUTLET BEFORE YOU CALL FOR SERVICE The electrical requirements are a 120 volt 60 Hz, AC only, 15 amp. or more protected electrical supply. It is recommended that a separate circuit serving only this appliance be provided. Read the BEFORE YOU CALL and operating instruction sections in your Operation Manual. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this range.