Installation Guide

ManualsBrandsSharp ManualsAppliances30 in. 5 Burners Slide-in Electric Range in Stainless Steel with Air Fry and Convection

SSR3061JS, SSR3065JS, SSR3071JS

30" SLIDE-IN ELECTRIC RANGE

INSTALLATION MANUAL

IMPORTANT NOTICE

• Read and save these instructions for future reference.

• Installation and service must be performed by a qualiﬁed

installer.

• Save this installation manual for local electrical inspector's

use.

WARNING

• If the information in this manual is not followed exactly, a re or

explosion may occur, causing property damage, personal injury

or death. In the event of a re or explosion, more away from the

appliance immediately and call the local re department.

• NEVER attempt to extinguish oil/grease re with water.

• Do not store or use gasoline or other ammable vapors and liquids

in the vicinity of this or any other appliance.

• Installation and service must be performed by a qualied installer,

serviceperson.

SAFELY LIFT AND MOVE UNIT

• Two people are required to safely lift and move this unit.

• Do not move unit by pushing or pulling on the door or control

panel. Do not lift by the cooktop edges. Push, pull or lift only

on the body or structural areas, such as oven, oven face or back

corners of range.

• Move range by lifting, not sliding, to prevent damage to oors.

Use cardboard, plywood, or stiff plastic to protect oors if sliding

is necessary.

UNPACKING APPLIANCE

• Remove all packing mater ials f rom inside the appliance. Remove

the feature sticker, if there is one, from the outside of the oven.

• Check the appliance for any damage. If there is any damage,

do not operate the appliance and contact your dealer or a Sharp

Authorized Servicer.

• Record the model and serial number.

IMPORTANT NOTES TO THE INSTALLER

• Leave these instructions with the consumer after installation.

• Read the entire Installation Manual before installing the appli-

ance.

• Remove all packing material before connecting the electrical

supply.

INSTALLATION LOCATION

• The dimensions and clearances in this manual indicate minimum

clearance required.

• Minimum distance between rangetop and overhead cabinetry

is 30".

• The contact surface and oor on which the appliance rests must

be solid and level.

• Ensure installation location has proper electrical supply.

• Any openings in the wall behind the appliance and in the oor

under the appliance must be sealed.

OBSERVE GOVERNING CODES

• Observe all governing codes and ordinances.

• This appliance requires connection to a 3-prong, 208/240VAC

60Hz grounded electrical source. When installed, appliance

must be electrically grounded in accordance with local codes

or, in the absence of local codes, with the National Electrical

Code, NFPA 70.

Summary of content (8 pages)

PAGE 1
SSR3061JS, SSR3065JS, SSR3071JS 30" SLIDE-IN ELECTRIC RANGE INSTALLATION MANUAL IMPORTANT NOTICE UNPACKING APPLIANCE • Remove all packing materials from inside the appliance. Remove the feature sticker, if there is one, from the outside of the oven. • Check the appliance for any damage. If there is any damage, do not operate the appliance and contact your dealer or a Sharp Authorized Servicer. • Read and save these instructions for future reference.
PAGE 2
TOOLS NEEDED PARTS Before installing, verify all parts are included. If any parts are damaged and/or missing, contact your dealer or a Sharp Authorized Servicer.
PAGE 3
IMPORTANT NOTES TO THE CONSUMER ELECTRICAL SUPPLY REQUIREMENTS Keep this Installation Manual with your Operation Manual for future reference. This unit must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on the rating plate. • When using any appliance generating heat, safety precautions must be followed.
PAGE 4
INSTALLATION PROCEDURE CUTOUT DIMENSIONS SLIDE-IN CUTOUT Width 30" Depth 2311/16" CAUTION LACERATION, FOREIGN OBJECT, CRUSH HAZARD FREESTANDING CUTOUT Width 30" Depth 25" • When installing, moving or servicing any appliance, wear proper protective equipment, including cut resistant gloves, steel-toed shoes and safety glasses. IMPORTANT Failure to remove packaging materials could result in damage to the appliance.
PAGE 5
TO INSTALL REAR TRIM TO INSTALL ANTI-TIP BRACKET 1 Align filler trim to mounting holes. 2 Attach with screws provided as shown in Figure 5. FIGURE 5 1 ELECTRICAL SUPPLY CONNECTION Using the template provided with the Anti-Tip Bracket, locate the installation area of the Anti-Tip Bracket. The Anti-Tip Bracket may be installed at either the back-left or back-right corner of the installation space, and only one Anti-Tip Bracket is necessary.
PAGE 6
TO CONNECT WITH 3-PRONG POWER CORD A 3-wire or 4-wire, split-phase 208VAC or 240VAC 60Hz electrical system must be used. If the electrical service provided does not meet the above specifications, have a licensed electrician install an approved outlet. 3-PRONG POWER CONNECTION RED WIRE Access the range electrical terminal block by removing the screw attaching the rear access cover on the back of the range. See Figure 6.
PAGE 7
• The metal flange under each side of the cooktop MUST be placed over the cabinet countertop for proper unit support. The cooktop should NOT rest directly on the countertop or else it could cause damage to the cooktop voiding the warranty. See Figure 10. PLACING UNIT IMPORTANT • Do not move unit by pushing or pulling on the door or control panel. Do not lift by the cooktop edges. Push, pull or lift only on the body or structural areas, such as oven, oven face or back corners of range.
PAGE 8
MODEL AND SERIAL NUMBER LOCATION CONFIRM OPERATION After the range has been installed and assembled and the electrical power cord has been connected, confirm the operation of all cooktop surfaces. The model and serial number are needed when contacting customer service and to register the product and order replacement parts. The name plate label contains appliance certification, rating and identification information. It is located inside the storage drawer on either the left or right side panel.