UV420 Owner’s Guide www.sharkclean.com UV420_26_IB_E_120810_3.
This manual covers model numbers: UV420 26 TECHNICAL SPECIFICATIONS Voltage: 120V. Watts: 1200W Amps: 10A Hertz: 60Hz TOLL FREE: 1-800-798-7398 UV420_26_IB_E_120810_3.
Contents Thank you for purchasing the Shark® Navigator™ Professional. Important Safety Instructions 2 Getting Started 4 Using the Vacuum 6 Cleaning with the Vacuum Accessories 7 Emptying the Dust Cup Assembly 8 Proper Care of Your Vacuum 9 Troubleshooting 10 Checking for Blockages 11 Maintenance 12 Warranty and Registration 13 www.sharkclean.com UV420_26_IB_E_120810_3.
IMPORTANT SAFETY INSTRUCTIONS For Household Use Only WHEN USING YOUR SHARK® NAVIGATOR™ PROFESSIONAL VACUUM, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS BEFORE USING YOUR SHARK® NAVIGATOR™ PROFESSIONAL VACUUM. POLARIZED PLUG: This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. Do not force into the outlet or try to modify the plug to fit.
HOSE ATTACHMENTS: DUST CUP/FILTERS/ACCESSORIES: 1. DO NOT use if air flow is restricted; if the air paths, the hose, or the accessories become blocked, turn the vacuum cleaner off. Remove all obstructions before you turn on the unit again. Before turning on the vacuum: 2. Keep the end of the hose and accessory openings away from face and body. 1. Make sure that all filters are thoroughly dry after routine cleaning. 2. Make sure that dust cup and all filters are in place after routine maintenance.
Getting Started 8 D C 4 A 5 7 F E B 2 G H 3 I WHAT’S IN THE BOX YOU JUST OPENED: A B C D E F G H I Vacuum Body Floor Power Nozzle Handle Assembly Super Stretch Hose Cleaning Wand with Handle Cleaning Wand Pet Hair Power Brush Cleaning Attachments 16” Crevice Tool* 4 Your Shark® Navigator™ Professional is easy to assemble: 1 Lay your vacuum body on a level surface. 2 Slide the electrical connection from the power nozzle into the main body to click into place.
9 10 c a d b 9 Attach the Super Stretch Hose: a) Snap hose into swivel connector b) Route under anti-tip hook to prevent vacuum from tipping 10 To store the vacuum: 11 To carry the vacuum: When storing your vacuum, wind the cord around the two cord holders and secure with cord clip: With the unit in the standing position, lift by the Dust Cup Assembly Handle (carry handle). c) Route over upper hose holder • Quick Cord release at the top of the unit – place in the upright position.
Using the Vacuum IMPORTANT: To protect your carpets, the brushroll will only turn on when you have pulled the handle back towards you and released the Floor Power Nozzle. Release suction for easier push and pull on high pile carpets and area rugs. 4 3 Power Switch Settings OFF Suction Release 6 Bare Floors / Tools Carpets 2 Your Shark® Navigator™ Professional Vacuum can be used to clean bare floors or carpets – with the click of a switch. Stand the vacuum into the upright position.
Cleaning with the Vacuum Accessories 1 2 3 4 5 6 7 4 3 2 Using the Cleaning Wand: Stand the vacuum into upright position. 5 Remove the Cleaning Wand with handle (with hose attached) from the unit. 6 Before cleaning with your accessories: Stand vacuum into upright position. Secure Super Stretch Hose in the anti-tip hose hook to prevent tipping. Push the selected tool into the end of the Cleaning Wand.
Maintenance CAUTION: Unplug the vacuum; failure to do so might result in electric shock. For best results empty the Dust Cup Assembly after each use, as needed during prolonged usage or when it reaches the MAX fill line. DO NOT OVERFILL. Turn vacuum off before emptying. 2 1 3 To empty the Dust Cup: 1 Grip carry handle and press the Dust Cup release button to remove. 2 Option A: For Quick Empty: Insert Dust Cup deep inside trash receptacle to contain dust and debris.
COMPONENT MAINTENANCE SCHEDULE 1 Dust Cup Empty each time you vacuum. 2 Pre-Motor Foam Filter Rinse and air dry every month under normal use. 3 Pre-Motor Felt Filter Rinse and air dry every month under normal use. 4 Post-Motor HEPA Filter Clean once a year under normal use. DO NOT operate the vacuum without ALL the filters in place. DO NOT operate the vacuum with WET filters. Pre-Motor Foam Filter I MPORTANT: Loss of Suction may occur if foam filter is not cleaned every month.
Troubleshooting WARNING: to reduce the risk of electric shock, the power cord must be disconnected before performing maintenance/troubleshooting checks. PROBLEM POSSIBLE REASONS & SOLUTIONS Vacuum is not picking up dirt. Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-inserting back into the vacuum. (See “Maintenance” sections for instructions.) Dust cup may be full; empty dust cup.
Checking for Blockages 2 1 4 3 Unplug the vacuum before checking for blockages. Reassemble all parts securely before operating vacuum. Blockages may cause your vacuum to overheat and shut down. If so, clear the blockages, then follow the instructions for Resetting the Motor Thermostat on page 12. WARNING: Never insert sharp objects into any opening to clear an obstruction.
Maintenance A 1 Cleaning the Pet Hair Power Brush - Rotating Brush Slide locking latch (A) forward. Gently tilt brush housing upward to open. I MPORTANT: DO NOT force; it will not open all the way. Remove debris from turbine wheel and air passage. CLEANING THE MOTORIZED FLOOR BRUSH When your motorized floor brush needs cleaning or locks onto an object, it automatically shuts down to prevent damage to your lifetime belt.
Euro-Pro Five-Year (5) Limited Warranty EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of five (5) years from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions. If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid to: • U.S.
Euro-Pro Operating LLC USA: Newton, MA 02459 CAN: 4400 Bois Franc, St-Laurent, QC H4S 1A7 English: 1-800-798-7398 www.sharkclean.com Copyright © Euro-Pro Operating LLC 2012 Printed in China Illustrations may differ from actual product. UV420.E.120810.3 UV420_26_IB_E_120810_3.
