WWW.SHARKCLEAN.
IMPORTANT SAFETY INSTRUCTIONS For Household Use Only WHEN USING AN ELECTRICAL APPLIANCE, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS BEFORE USING YOUR SHARK NAVIGATOR® LIFT-AWAY® DELUXE. POLARIZED PLUG: To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way.
HOSE ATTACHMENTS: DUST CUP/FILTERS/ACCESSORIES: 1. DO NOT use if air flow is restricted; if the air paths, the hose, or the accessories become blocked, turn the vacuum cleaner off. Remove all obstructions before you turn on the unit again. Before turning on the vacuum: 2. Keep the end of the hose and accessory openings away from face and body. 3. Keep cleaning tools and hose suction openings away from hair, face, fingers, uncovered feet, or loose clothing. 4.
This manual covers model numbers: UV440 26 TECHNICAL SPECIFICATIONS Voltage: 120V., 60Hz Watts: 1200W Amps: 10A Euro-Pro, Shark, and Navigator are trademarks of Euro-Pro Operating LLC. All other brand names may be trademarks of their respective owners.
Contents Thank you for purchasing the Shark Navigator® Lift-Away® Deluxe Getting Started 6 Mode 1: Upright Vac 8 Mode 2: Portable Lift-Away® 10 Above-Floor Cleaning 11 Storage 12 Maintenance 13 Emptying the Dust Cup 13 Cleaning the Pre-Motor Filters 13 Cleaning the Post-Motor HEPA Filter 14 Cleaning the Pet Power Brush 14 Cleaning the Motorized Floor Brush 14 Checking for Blockages 15 Troubleshooting Guide 16 Ordering Parts 17 Warranty & Product Registration 19 www.
Getting Started a b Fig. 1 Fig. 2 c Fig. 4 d Fig. 3 f g Fig.
Your new Shark Navigator ® Lift-Away ® Deluxe vacuum cleaner can easily be configured into different cleaning modes to meet all your cleaning needs: upright vacuum and portable LiftAway ® - both with constant suction power. Fig. 6 Fig. 7 MODES: 1 UPRIGHT VAC 2 PORTABLE LIFT-AWAY® Upright vacuuming - floors and carpets. (Fig. 6) Take the Lift-Away ® with you around the house to clean hard to reach places. (Fig. 7) www.sharkclean.
Mode 1: Upright Vac To reduce the risk of electric shock, unplug the unit before assembling, adding or removing attachments or converting modes. WARNING: The On/Off switch is on the top of the Lift-Away ® canister. Always ensure the power is OFF (“O” position) before plugging and unplugging. b d a Upper Cord Storage Wrap e c Fig. 9 Fig. 8 Fig. 10 TO ASSEMBLE: 1 Place the floor nozzle on a level surface.
Suction Release Collar c Release suction for easier push & pull on high pile carpets and area rugs. a b Fig. 11 TO USE: Fig. 12 4 1 R otate the cord release to quickly release the power cord. 2 Secure the power cord in the cord hook. Gently press the floor nozzle down with your foot while you grasp the handle and tilt it back towards you. (Fig. 12) NOTE: The rotating brush on the motorized floor brush will not spin unless the nozzle is flat against the floor and the handle is tilted back.
Mode 2: Portable Lift-Away® You can carry your vacuum cleaner in both modes by the carry handle located on top of the dust cup. a a b Fig. 13 Fig. 14 PORTABLE LIFT-AWAY® 1 S eparate the portable Lift-Away ® canister from the floor nozzle by pressing the red release button (a) on the side of the canister. Gently hold the nozzle to the floor with your foot and pull the canister up. (Fig.
Above-Floor Cleaning Fig. 16 Release suction when dusting delicate objects, furniture or draperies. a Suction Release Collar CLEAN ABOVE THE FLOOR IN UPRIGHT VAC OR PORTABLE LIFT-AWAY® MODE 1 P ress the handle release button and pull the handle up or press the extension wand release button and pull the extension wand up. 2 ttach desired accessory onto the end of either the A extension wand or the handle. (Fig. 16) 3 our vacuum has tremendous suction Y power.
Storage and Maintenance Quick Cord Release Lower Cord Storage Clip Fig. 17 STORE YOUR VACUUM SAFELY 1 Convert your vacuum back to upright vac mode. 2 R otate the upper quick cord release to its upright position and coil the power cord loosely around the two clips. Clip the plug onto the cord to secure. (Fig. 17) 3 S tore the dusting brush and the crevice tool on the mounts on the accessory holder.
Maintenance COMPONENT MAINTENANCE SCHEDULE 1 Dust Cup Empty each time you vacuum. 2 Pre-Motor Foam Filter Rinse and air dry every 3 months under normal use. 3 Pre-Motor Felt Filter Rinse and air dry every 3 months under normal use. 4 Post-Motor HEPA Filter Clean once every 2 years or as needed. I MPORTANT: Loss of Suction may occur if foam filters are not cleaned every 3 months. Rinse and allow to air dry completely. Also, tap loose dirt off filter between washes as needed.
Maintenance - cont’d CLEANING THE POWER BRUSH 1 S lide the locking latch (a) forward and gently tilt brush housing upward to remove. (Fig. 25) 2 arefully remove any blockage or debris and C cut away any build-up of hair or string wrapped around the rotating bristle brush with scissor. 3 T o reassemble, insert the tabs on the front edge of the bottom cover into the matching holes in the top half and tilt it back down until it clicks into place. (Fig. 26) Fig. 22 a Fig. 23 Fig. 24 Fig. 26 Fig.
Make sure you are working in a well lit area and use a flashlight to help search for blockages. Fig. 28 Fig. 29 CHECKING FOR BLOCKAGES Fig. 30 4 Blockages may cause your vacuum to overheat and shut down. To prevent this from happening, check potential blockage areas after heavy use or if you detect a loss of suction or poor cleaning performance. 1 • D etach the stretch hose from the back of the portable Lift-Away ® canister by squeezing the tabs together and pulling up. (Fig.
Troubleshooting Guide PROBLEM POSSIBLE REASONS & SOLUTIONS Vacuum is not picking up dirt. Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-inserting back into the vacuum. (See “Maintenance” sections for instructions.) Dust cup may be full; empty dust cup. Check hose and hose connections for blockages; clear blockages if required. If dust cup is empty, and attachment inlets are clear, check for other blockages.
Ordering Parts 1 2 3 4 5 To purchase replacement parts, please visit our website: www.sharkclean.com or contact customer service: 1-800-798-7398. PART PART NO. 1 Pre-Motor Filter Set XFF350 2 HEPA Filter XHF350 3 Dusting Brush & Crevice Tool 112FFJ 4 Power Brush 119FFJ 5 Extension Wand 1116FC www.sharkclean.
Notes 18 TOLL FREE: 1-800-798-7398
EURO-PRO FIVE-YEAR (5) LIMITED WARRANTY EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of five (5) years from the date of purchase when utilized for normal household use, subject to the following conditions, exclusions and exceptions. The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option.
EURO-PRO Operating LLC U.S.: Newton, MA 02459 Canada: Ville St. Laurent, Québec H4S 1A7 1-800-798-7398 www.sharkclean.com Copyright © Euro-Pro Operating LLC 2013 Printed in China Illustrations may differ from actual product. Euro-Pro, Shark, and Navigator are trademarks of Euro-Pro Operating LLC. All other brand names may be trademarks of their respective owners. UV440.26.E.130419.