UX-460 MODEL UX-460 FACSIMILE FACSIMILE OPERATION MANUAL 1. Installation 2. Using the Answering Machine 3. Sending Documents 4. Receiving Documents 5. Making Copies 6. Making Telephone Calls 7. Special Functions 8. Option Settings 9. Printing Reports and Lists 10. Maintenance 11.
WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Introduction Welcome, and thank you for choosing a Sharp facsimile! The features and specifications of your new Sharp fax are shown below. Automatic dialing Rapid Key Dialing: 5 numbers Speed Dialing: 40 numbers Imaging film Initial starter roll (included with fax machine): 32 ft. (10 m) roll (approx. 30 letter-size pages) Replacement roll: UX-3CR 98 ft. (30 m) roll (two rolls in package, one roll yields approx. 100 lettersize pages) Automatic document feeder 10 sheets max.
Display 16-digit LCD display Recording system Thermal transfer recording Paper tray capacity (16- to 20-lb. paper) Letter: 60 sheets Legal: 30 sheets Halftone (grayscale) 64 levels Applicable telephone line Public switched telephone network Compatibility ITU-T (CCITT) G3 mode Compression scheme MH, MR, Sharp Scanning method Sheet-feeder CIS (Contact Image Sensor) Effective printing width 8.3" (208 mm) max. Input document size Automatic feeding: Width: 5.8 to 8.
Important safety information • Do not disassemble this machine or attempt any procedures not described in this manual. Refer all servicing to qualified service personnel. • This machine must only be connected to a 120 V, 60 Hz, grounded (3-prong) outlet. Connecting it to any other kind of outlet will damage the machine and invalidate the warranty. • Do not install or use the machine near water, or when you are wet. Take care not to spill any liquids on the machine.
• Use caution when installing or modifying telephone lines. • Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. • Do not use a telephone to report a gas leak in the vicinity of the leak. • The power outlet must be installed near the equipment and must be easily accessible.
Table of Contents 1 Installation 7 Unpacking Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 A Look at the Operation Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Loading the Imaging Film. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Loading Printing Paper . . . . . . . . . . . . . . . . . . . . . . . . .
7 Special Functions 88 Caller ID (Requires Subscription from Telephone Company). . . . . . . 88 Distinctive Ring (Requires Subscription from Telephone Company) . 93 Broadcasting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Cover Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Batch Page Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Installation Chapter 1 Installation Unpacking Checklist Before setting up, make sure you have all of the following items. If any are missing, contact your dealer or retailer.
A Look at the Operation Panel A Look at the Operation Panel 1 2 3 4 5 7 6 8 9 10 TEL FAX TAD DIGITAL ABC 1 GHI 2 JKL 7 5 8 ANSWERING SYSTEM RECEPTION MODE REC/MEMO PLAY/SKIP RESOLUTION REDIAL VOLUME DOWN UP FUNCTION DELETE 6 WXYZ TUV REPEAT 3 MNO 4 PQRS SPEED DIAL DEF HOLD/ SEARCH COPY/HELP 9 STOP SPEAKER 01 02 03 04 05/POLL 0 START/MEMORY 11 8 12 13 14 15 16 17 18 19 1 SPEED DIAL key Press this key to dial a 2-digit Speed Dial number.
6 RECEPTION MODE key Press this key to select the reception mode. An arrow in the display will point to the currently selected reception mode. 7 RESOLUTION key Press this key to adjust the resolution and contrast before sending or copying a document. 8 VOLUME keys Press these keys to adjust the volume of the handset when the handset is lifted, the volume of the speaker when the SPEAKER key has been pressed, or the volume of the ringer at all other times.
A Look at the Operation Panel 16 DELETE key Press this key to erase recorded messages. 17 STOP key Press this key to cancel operations before they are completed. 18 START/MEMORY key Press this key to send or receive a document, or to scan a document into memory before sending it. 19 COPY/HELP key When a document is in the feeder, press this key to make a copy. At any other time, press this key to print out the Help List, a quick reference guide to the operation of your fax.
Connections Points to keep in mind when setting up Do not place the machine in direct sunlight. Do not place the machine near heaters or air conditioners. Keep dust away from the machine. Keep the area around the machine clear. About condensation If the machine is moved from a cold to a warm place, it is possible that condensation may form on the scanning glass, preventing proper scanning of documents for transmission.
Connections Handset Connect the handset as shown and place it on the handset rest. ♦ The ends of the handset cord are identical, so they will go into either jack. Make sure the handset cord goes into the jack marked with a handset symbol on the side of the machine! Use the handset to make ordinary phone calls, or to transmit and receive documents manually.
Power cord Plug the power cord into a 120 V, 60 Hz, grounded (3-prong) AC outlet. Caution! Do not plug the power cord into any other kind of outlet. This will damage the machine and is not covered under the warranty. The machine does not have a power on/off switch, so the power is turned on and off by simply plugging in or unplugging the power cord.
Connections Telephone line cord Insert one end of the line cord into the jack on the back of the machine marked TEL. LINE. Insert the other end into a standard (RJ11C) single-line wall telephone jack. TE SEL. T T EL LI . NE Be sure to insert the telephone line cord into the TEL. LINE jack. Do not insert it into the TEL. SET jack! Comments: • Your fax is set for touch-tone dialing. If you are on a pulse dial (rotary) line, you must set the fax for pulse dialing by changing Option Setting 8.
Trays Attach the paper tray extension. ♦ Pull the paper release plate forward. Insert the paper tray extension horizontally into the notches in the paper tray. Rotate the paper tray extension up until it snaps into place. Attach the original document support. Note: The original document support has a top side and a bottom side. If you cannot insert the tabs on the support into the holes, turn the support over. 15 1.
Connections Extension phone (optional) If desired, you can connect an extension phone to the TEL. SET jack on the fax. 1 Remove the seal covering the TEL. SET jack. 2 Connect the extension phone line to the TEL. SET jack. TE SEL. T T EL LI .
Loading the Imaging Film Your fax uses a roll of imaging film to create printed text and images. The print head in the fax applies heat to the imaging film to transfer ink to the paper. Follow the steps below to load or replace the film. The initial starter roll of imaging film included with your fax can print about 30 letter-size pages. When replacing the film, use a roll of Sharp UX-3CR imaging film. One roll can print about 100 letter-size pages.
Loading the Imaging Film If you are installing the imaging film for the first time, go to Step 6. 3 Remove the imaging film cartridge from the print compartment (grasp the handle at the front of the cartridge) and turn it over. 4 Remove the used film from the cartridge. 5 Remove the four green gears from the used film.
6 Remove the new roll of imaging film from its packaging. • Do not yet remove the band that holds the rolls together. 7 Insert the large gear into the green end of the empty spool. Make sure the two protrusions on the large gear fit firmly into the slots in the end of the spool. Insert the remaining three gears into the spools, making sure the protrusion on each gear fits firmly into one of the slots in the end of each spool.
Loading the Imaging Film 8 Insert the large gear into the large holder on the imaging film cartridge (make sure it clicks into place), and then insert the small gear on the other end of the spool into its holder. 9 Cut the band that holds the two spools together. Unroll the film slightly and insert the small gears into their holders. 10 20 Turn the cartridge over, grasp the handle, and insert the cartridge into the print compartment.
11 Rotate the large gear toward you until the film is taut. 12 Close the print compartment cover (press down on both sides to make sure it clicks into place), and then close the operation panel. Click! 13 Load paper in the paper tray and then press the following keys to initialize the film. Note: Paper must be loaded before the film can be initialized. To load paper, see the following section, Loading the Printing Paper.
Loading Printing Paper Loading Printing Paper You can load letter or legal size paper in the paper tray. The maximum number of sheets depends on the weight and size of the paper you are loading. 2 ♦ Paper from 16 to 20 lbs. (60 to 75 g/m ): Letter size: 60 sheets Legal size: 30 sheets 2 ♦ Paper from 20 to 24 lbs. (75 to 90 g/m ): Letter size: 50 sheets Legal size: 25 sheets 1 Fan the paper, and then tap the edge against a flat surface to even the stack. 2 Pull the paper release plate toward you.
4 Push the paper release plate back down. If the paper release plate is not pushed down, paper feed errors will result. Note: When receiving faxes or copying documents, do not allow a large number of pages to accumulate in the output tray. This may obstruct the outlet and cause paper jams. 5 The fax has been set at the factory to scale the size of received faxes to letter size paper. If you have loaded legal paper, you must change the paper size setting to legal.
Loading Printing Paper 6 Your fax has been set at the factory to print at normal contrast. Depending on the type of paper you have loaded, you may find that you obtain better print quality by changing the setting to LIGHT. Press these keys: FUNCTION 6 The display will show: PRINT CONTRAST Press 1 to select NORMAL or 2 to select LIGHT. NORMAL 1 The display will show: or LIGHT 2 PAPER SIZE SET Press the STOP key to return to the date and time display.
Entering Your Name and Fax Number Once you enter this information, it will automatically appear at the top of each fax page you send. Before you can begin using your fax, you need to enter your name and the telephone number of your fax. You also need to set the date and time. Important! The law requires that your name, telephone/fax number, and the date and time appear on each fax message you send.
Entering Your Name and Fax Number 2 Press the # key twice: The display will show: OWN NUMBER SET 3 Press the START/MEMORY key. START/MEMORY The display will show: ENTER FAX # 4 Enter your fax number by pressing the number keys. Up to 20 digits can be entered. • To insert a space between digits, press the # key. • If you make a mistake, press the HOLD/SEARCH key to move the cursor back to the mistake and then enter the correct number. The new number will replace the old number.
6 Enter your name by pressing the number keys as shown in the chart below. Up to 24 characters can be entered. • To enter two letters in succession that require the same key, press the SPEAKER key after entering the first letter. Example: SHARP = 7 7 7 7 7 4 4 4 2 2 7 7 7 7 SPEAKER A= J= S= B= K= T= C= L= U= D= M= V= E= N= W= F= O= X= G= P= Y= H= Q= Z= I= R= SPACE = GHI ABC DEF JKL MNO SPEED DIAL 77 Press this key to delete the letter highlighted by the cursor.
Setting the Date and Time Setting the Date and Time The date and time appear in the display and reports, and are printed at the top of every page you fax. 3 key * key 1 2 3 4 5 6 7 8 9 FUNCTION key START/MEMORY key 0 STOP key Note: The imaging film and printing paper must be loaded before the date and time can be set. 1 Press these keys: FUNCTION The display will show: ENTRY MODE 2 Press the * key four times. The display will show: DATE & TIME SET Note: The fax is Year 2000 compliant.
3 Press the START/MEMORY key. START/MEMORY • The currently set date will appear in the display. 4 Enter a two-digit number for the month ("01" for January, "02" for February, "12" for December, etc.). • To correct a mistake, press the SPEED DIAL key to move the cursor back to the mistake, and then enter the correct number. Example: January 5 5 1 9 9 9 Enter a two-digit number for the hour ("01" to "12") and a two-digit number for the minute ("00" to "59").
Setting the Date and Time 9 Press the START/MEMORY key to start the clock. START/MEMORY The display will show: DAY LIGHT SAVING 10 Press the STOP key to return to the date and time display. STOP Daylight Saving Time If desired, you can have the clock move forward and backward automatically at the beginning and end of Daylight Saving Time.
Selecting the Reception Mode Your fax has three modes for receiving incoming calls and faxes: TEL mode: Select this mode when you want to receive both phone calls and faxes on the line connected to the fax machine. All calls, including faxes, must be answered by picking up the fax machine’s handset or an extension phone connected to the same line. FAX mode: Select this mode when you only want to receive faxes on your line.
Volume Adjustment Volume Adjustment You can adjust the volume of the speaker, handset, and ringer using the UP and DOWN keys. DOWN key UP key 1 2 3 4 5 6 7 8 9 0 Speaker 1 Press the SPEAKER key. 2 Press the UP or DOWN key. SPEAKER DOWN 3 32 When the display shows the desired volume level, press the SPEAKER key to turn off the speaker.
Handset 1 Lift the handset. 2 Press the UP or DOWN key. Display: DOWN or UP RECEIVER: HIGH RECEIVER: MIDDLE 3 When the display shows the desired volume level, replace the handset. Ringer 1 Press the UP or DOWN key. (Make sure the SPEAKER key has not been pressed and the handset is not lifted.) • The ringer will ring once at the selected level, then the date and time will reappear in the display.
Using the Answering Machine The UX-460’s built-in answering machine allows you to receive both voice messages and fax transmissions while you are out. To use the answering machine, record an outgoing message and then set the reception mode to TAD when you go out. Recording an Outgoing Message The outgoing message (OGM) is the greeting that the machine plays after answering a call to inform callers that they can leave a message or send a fax. Example: "Hello. You’ve reached the ABC company.
Recording an Outgoing Message 3 Press the START/MEMORY key. START/MEMORY 4 5 Press 1 to select GENERAL. (If you are recording a message for the Transfer function explained later in this chapter, press 2 for TRANSFER.) GENERAL TRANSFER 1 or 2 Pick up the handset, press the START/MEMORY key, and speak into the handset. • The outgoing message can be up to 60 seconds long. The outgoing message for the Transfer function can be up to 15 seconds long.
Recording an Outgoing Message To listen to or erase an outgoing message To listen to or erase an outgoing message, follow Steps 1 through 4 of the above procedure to select the message, and then press the PLAY/SKIP key to listen to it, or the DELETE key to erase it. To return to the date and time display, press the STOP key twice. Note that the general outgoing message cannot be erased. If you need to change it, simply repeat the recording procedure.
Operating the Answering Machine Operating the Answering Machine 2. Answering Machine Activating the answering machine Activate the answering machine before you go out as follows: Press the RECEPTION MODE key until the arrow in the display points to TAD. RECEPTION MODE • The outgoing message will play (you can stop playback by pressing the STOP key). TEL FAX • It will not be possible to set the reception mode to TAD if a general outgoing message has not been recorded.
Operating the Answering Machine Listening to received messages When you return, the display will show the number of messages recorded. Listen to the messages as follows: 1 Press the PLAY/SKIP key. • If you only want to listen to new PLAY/SKIP messages (messages not previously listened to), continue to hold the PLAY/SKIP key down for at least two seconds. 2 The messages will play. • As each message plays, the date and time of recording will appear briefly in the display.
Operating the Answering Machine Erasing received messages • Erasing all messages: To erase all messages, press and hold down the DELETE key for at least 2 seconds. 2. Answering Machine It is important to erase received messages after you listen to them to ensure that the memory does not become full. DELETE • Erasing a single message: To erase only a single message, press the DELETE key while the message is being played.
Operating the Answering Machine Date and time of ICMs You can check the date and time of your received messages by pressing the panel keys as shown below. ♦ The dates and times are also shown in the Message List, which can be printed out as described in Chapter 9. 1 Press these keys: FUNCTION 0 The display will show: T.A.D. SETTINGS 2 Press these keys: The display will show: ICM CONFIRMATION 3 4 Press the START/MEMORY key. The number of messages recorded will appear in the display.
Optional Answering Machine Settings Optional Answering Machine Settings Setting ICM time Incoming messages (ICMs) are the messages which callers leave for you on the built-in answering machine. The answering machine is set at the factory to allow each caller a maximum of 4 minutes to leave a message. If desired, you can change this setting to 15, 30, or 60 seconds. 1 Press these keys: FUNCTION 0 The display will show: T.A.D.
Optional Answering Machine Settings Fax reception on TAD failure If the memory for recording incoming messages becomes full while you are out, the answering machine will no longer be able to record messages. The ON TAD FAILURE setting is used to choose the response of the machine to incoming calls when this happens: ♦ Automatic fax reception NO: The UX-460 will answer after 20 rings, after which it will wait to receive a remote command.
Optional Answering Machine Settings Calling Party Control detection When a caller hangs up, the central telephone exchange will issue a signal called a Calling Party Control (CPC) signal. The built-in answering machine has been set to detect this signal, and this allows it to immediately stop recording when a caller hangs up, thereby saving memory space and freeing you from having to listen to long periods of silence when you play back your messages.
Optional Answering Machine Settings OGM only mode If needed, you can turn off recording of incoming messages. In this case, your outgoing message will play, but callers will not be able to leave a message. (The machine will still receive faxes sent by automatic dialing.) 1 Press these keys: The display will show: 2 FUNCTION 0 OGM ONLY MODE Press 1 to turn on OGM only mode, or 2 to turn it off. 1 3 44 Press the STOP key.
Transfer Function The Transfer function is used to make the UX-460 automatically call you at a specified number every time it receives an incoming message. This lets you hear your messages immediately after they come in, even when you are at a remote location. When you answer the telephone, you will hear your recorded message telling you that the call is a transfer call. Enter "#", your remote code number, and "#". The answering machine will then play back your messages.
Transfer Function 3 Press the START/MEMORY key. START/MEMORY 4 Enter a transfer number (max. of 32 digits including pauses) by pressing the number keys. 5 5 5 1 2 3 4 (Example) 5 Press the START/MEMORY key and then the STOP key. STOP START/MEMORY Recording the transfer message The transfer message plays when you answer the telephone, and informs you that the call is a transfer call. It can be up to 15 seconds long.
Transfer Function 1 Press these keys: 2. Answering Machine Turning the Transfer function on and off FUNCTION 0 The display will show: T.A.D. SETTINGS 2 Press these keys: The display will show: TRANSFER FUNC 3 4 Press 1 to turn the Transfer function on, or 2 to turn it off. Press the STOP key.
Override Ringing Override Ringing This function allows selected callers using a tone dial telephone to override the answering machine’s outgoing message and cause the UX-460 to make a special ringing sound, alerting you that they are calling. This is useful when you are near the machine but only want to talk with certain callers, taking all other calls on the answering machine.
Override Ringing Overriding the answering machine 1 2. Answering Machine Your callers should follow the steps below to override the answering machine. Your caller calls the UX-460 from a tone dial telephone. When the outgoing message begins, they should press the "#" key on their telephone. • The caller will hear a short beep, and the outgoing message will stop. 2 The caller should enter the override code and "#" by pressing the appropriate keys on their telephone.
Remote Operations Remote Operations You can call the UX-460 from any touch-tone telephone and play back your messages using the remote commands. You can also use these commands to change the reception mode and other settings. Remote code number To perform remote operations, you must first program a remote code number. This number is used to prevent unauthorized people from listening to your messages or changing the settings of your machine. The remote code number has been set to "001" at the factory.
Remote Operations Toll Saver 2. Answering Machine When you call the UX-460 to listen to your messages, it will answer after two rings if it has received at least one message, or after four rings if it has not received any messages. This allows you to save money on telephone charges, particularly if you are calling long distance. If the machine does not answer after the second ring, you can simply hang up before it answers, saving yourself the cost of that call.
Remote Operations Retrieving your messages Note: You can also access the UX-460 for remote operation when the reception mode is set to FAX. In this case, call the UX-460, press the "#" key immediately after it answers (before you hear the fax tone), and then continue from Step 2 below. 1 Call the UX-460 from a touch-tone telephone. When your outgoing message begins, press the "#" key on the telephone. • You will hear a short beep, and the outgoing message will stop.
Remote Operations 3 While the messages are playing, you can do any of the following: second time, press "2" and "#" on the telephone before that message ends. To move back to the previous message, press "2" and "#" within the first 3 seconds of the current message. 2 • Skip forward: To skip forward to 5 the next message, press "5" and "#" on the telephone. • Stop: To stop playback, press "0" 0 and "#" on the telephone.
Remote Operations • Repeat playback: To listen to your messages again, press "7" and "#". 7 • Perform other operations: You can enter any of the commands described in the following section, Other remote operations. • Hang up: If you do not erase your messages first, they will be saved and any new messages will be recorded after them.
Remote Operations After listening to your messages, you can do any of the operations described below by pressing the appropriate keys on the telephone. Note: The following commands cannot be entered while messages are being played back. If you do not want to wait until playback ends to enter a command, first stop playback by pressing "0" and "#", and then enter the command. Changing the fax reception mode Select a new reception mode by pressing the keys as follows: • TAD mode: "8", "1", and "#".
Remote Operations 2 When you hear a short beep, speak into the telephone to record the new message. • The message can be up to 15 seconds long. After 15 seconds (or earlier if the machine detects silence after you finish speaking), you will hear a beep, and the new message will be played back. Turning the Transfer function on or off To turn Transfer on: Press "9", "1", and "#" on the telephone. 9 1 (Example) To turn Transfer off: Press "9", "2", and "#" on the telephone.
Remote Operations 1 Press "9", "3", and "#" on the telephone. 2 When you hear a short beep, speak into the telephone to record the new message. 9 2. Answering Machine Recording a new transfer message 3 • The time for the transfer message is fixed at 15 seconds. After 15 seconds (or earlier if the machine detects silence after you finish speaking), you will hear a beep, and the new message will be played back automatically.
Remote Operations OGM only mode To turn on OGM only mode, press "1", "1", and "#". (Your outgoing message will play, but callers will not be able to record a message. Faxes sent by automatic dialling will be received). To turn off OGM only mode, press "1", "2", and "#".
Chapter 3 Sending Documents Transmittable Documents Size and weight 3. Sending Documents The size and weight of documents that you can load in the document feeder depend on whether you load one page at a time or several pages at once.
Transmittable Documents Note: Letters or graphics on the edges of a document will not be scanned. 5 mm Letters in the shaded area will not be scanned. 4 mm 4 mm 5 mm Other restrictions ♦ The scanner cannot recognize yellow, greenish yellow, or light blue ink. ♦ Ink, glue, and correcting fluid on documents must be dry before they pass through the document feeder. ♦ All clips, staples, and pins must be removed from documents before loading in the feeder.
Loading the Document Loading the Document Up to 10 pages can be placed in the feeder at one time. The pages will automatically feed into the machine starting from the bottom page. additional pages gently and carefully in the feeder just before the last page is scanned. Do not try to force them in, as this may cause double-feeding or jamming.
Loading the Document Removing a document from the feeder If you need to remove a document from the feeder, open the operation panel. Important: Do not try to remove a document without opening the operation panel. This may damage the feeder mechanism. 1 Open the operation panel by grasping the finger hold and pulling up. 2 Remove the document. 3 Close the operation panel, making sure it clicks into place.
Resolution and Contrast Resolution and Contrast If desired, you can adjust the resolution and contrast before sending a document. You must adjust the settings each time you don’t want to use the default settings. 3. Sending Documents The default resolution setting is STANDARD and the default contrast setting is AUTO. Note: The resolution and contrast settings are only effective for transmitting and copying a document. They are not effective for receiving a document.
Resolution and Contrast 1 Load the document(s). • The document must be loaded before the resolution and contrast can be adjusted. 2 Press the RESOLUTION key one or more times until the desired resolution and contrast settings appear in the display. RESOLUTION • The first time you move through the list of resolution settings, the contrast setting AUTO will appear next to each resolution setting. The second time you move through the list, the contrast setting DARK will appear.
Sending a Fax by Normal Dialing Sending a Fax by Normal Dialing With Normal Dialing, you pick up the handset (or press the SPEAKER key) and dial by pressing the number keys. ♦ If a person answers, you can talk with them through the handset before sending the fax. (If you pressed the SPEAKER key, you must pick up the handset to talk.) 3. Sending Documents ♦ Normal Dialing allows you to listen to the line and make sure the other fax machine is responding. 1 Load the document(s).
Sending a Fax by Normal Dialing 4 Wait for the connection. Depending on the setting of the receiving machine, you will either hear a facsimile reception tone or the other person will answer. Beep • If the other party answers, ask them to press their Start key (if you pressed the SPEAKER key, pick up the handset to speak with them). This causes the receiving machine to issue a reception tone. 5 When you hear the reception tone, press the START/MEMORY key. Replace the handset if you used it.
Sending a Fax by Automatic Dialing Sending a Fax by Automatic Dialing You can dial a fax or telephone number by simply pressing a Rapid Key, or by pressing the SPEED DIAL key and entering a two-digit number. ♦ To use Automatic Dialing, you must first store the full fax or 3. Sending Documents telephone number in your fax machine. ♦ When you store a fax or telephone number, you select a two-digit Speed Dial number for it. 45 Speed Dial numbers are available.
Sending a Fax by Automatic Dialing Storing fax and telephone numbers for Automatic Dialing 1 Press these keys: FUNCTION 3 The display will show: FAX/TEL # MODE 2 Press 1 to select SET. 1 The display will show: FAX/TEL # SET ENTER SPEED # 3 Enter a two-digit Speed Dial number by pressing the number keys (01 to 05 for Rapid Key Dialing, 06 to 45 for Speed Dialing). 1 0 4 (Example) Enter the fax or voice number by pressing the number keys (max. of 32 digits including pauses).
Sending a Fax by Automatic Dialing 6 Enter the name of the party by pressing the number keys as shown in the chart below. Up to 20 characters can be entered. • If you don’t want to enter a name, skip this step. • To enter two letters in succession that require the same key, press the SPEAKER key after entering the first letter. 7 A= J= S= B= K= T= C= L= U= D= SPEAKER M= V= E= N= W= F= O= X= G= P= Y= H= Q= Z= I= R= SPACE = 77 3.
Sending a Fax by Automatic Dialing Clearing numbers 1 FUNCTION Press these keys: 3 The display will show: FAX/TEL # MODE 2 Press 2 to select CLEAR. 3 Enter the Speed Dial number that you want to clear by pressing the number keys. 0 1 2 (Example) 4 Press the START/MEMORY key. START/MEMORY 5 Return to Step 3 to clear another number, or press STOP to exit. STOP Step 3 or Making changes To make changes in a number previously stored, repeat the storing procedure.
Sending a Fax by Automatic Dialing Rapid Key Dialing If the number you want to dial has been stored for Automatic Dialing as a Speed Dial number from 01 to 05, you can dial it by pressing the corresponding Rapid Key. 1 Load the document(s). 3. Sending Documents The display will show: READY TO SEND • Set the resolution and/or contrast if desired. 2 RESOLUTION Press the Rapid Key corresponding to the desired Speed Dial number. • The name of the receiving party will 01 02 03 appear in the display.
Sending a Fax by Automatic Dialing Speed Dialing Speed Dialing can be used to dial any number that has been stored for Automatic Dialing. 1 Load the document(s). The display will show: READY TO SEND • Set the resolution and/or contrast if desired. 2 Press the SPEED DIAL key and then enter the two digits of the Speed Dial number by pressing the number keys. RESOLUTION SPEED DIAL 2 • To enter numbers 1 through 9, first 0 enter 0 and then the number. (Example) 3 72 Check the display.
Sending a Fax by Automatic Dialing Direct Keypad Dialing You can also enter a full number with the number keys and then press the START/MEMORY key to begin dialing. You can use this method to dial a full number when you don’t need to speak to the other party before faxing. Load the document(s). 3. Sending Documents 1 The display will show: READY TO SEND • Set the resolution and/or contrast if RESOLUTION desired. 2 Enter the number of the receiving machine by pressing the number keys.
Sending a Fax by Automatic Dialing Using the HOLD/SEARCH key If you don’t remember the Rapid Key or Speed Dial number in which you have stored a particular fax number, you can search for the number by following the steps below. Once you have found the number, you can dial it and transmit the loaded document by simply pressing the START/MEMORY key. 1 Load the document(s). The display will show: READY TO SEND • Set the resolution and/or contrast if RESOLUTION desired.
Sending a Fax by Automatic Dialing 4 * Press the # key or the key to scroll through the names (numbers if you pressed 0). Stop when the desired name appears in the display. or • If no names have been stored that 5 Press the START/MEMORY key. The document will be automatically transmitted once the connection is made. 3. Sending Documents begin with the entered letter, you will scroll from the next name, in alphabetical order, in the list.
Chapter 4 Receiving Documents Using FAX Mode Press the RECEPTION MODE key until the arrow in the display points to FAX. RECEPTION MODE TEL FAX TAD When the reception mode is set to FAX, the machine will automatically answer all calls on four rings and receive incoming faxes. 4 rings Fax reception ♦ You can change the number of rings on which the machine answers calls by changing Option Setting 2. (See Chapter 8, Option Settings.
Receiving Documents Using TEL Mode Press the RECEPTION MODE key until the arrow in the display points to TEL. RECEPTION MODE TEL FAX 4. Receiving Documents TAD When the reception mode is set to TEL, you must answer all calls using the fax machine’s handset or an extension phone connected to the same line. Answering with the fax’s handset 1 Pick up the handset when the machine rings. 2 If you hear a fax tone, wait until the display shows RECEIVING and then replace the handset.
Receiving Documents 3 If the other party first talks and then wants to send a fax, press the START/MEMORY key after speaking (press your START/MEMORY key before the sender presses their Start key). • Make sure that the display shows RECEIVING, then replace the handset. START/MEMORY RECEIVING Answering with an extension phone 1 Answer the extension phone when it rings.
Receiving Documents Comments: • Your fax will not accept the signal to begin reception (5**) if a document is loaded in its feeder. • If you have set Option Setting 10 to NO and hear a fax tone when you answer * * the extension phone, you must press 5, , and if you are on a touch-tone phone, or walk over to the fax, pick up the handset, and press the START/MEMORY key if you are on a pulse dial phone.
Receiving Documents Reception Ratio The fax has been set at the factory to automatically reduce the size of received documents to fit the size of the printing paper. This ensures that data on the edges of the document are not cut off. If desired, you can turn this function off and have received documents printed at full size. Note: If a document is too long to fit on the printing paper, the remainder will be printed on a second page. In this case, the cut-off point may occur in the middle of a line.
Receiving Documents 4 Press the STOP key. STOP Substitute Reception to Memory In situations where printing is not possible, such as when your fax runs out of paper, the imaging film needs replacement, or the paper jams, incoming faxes will be received to memory. 4. Receiving Documents When you have received a document in memory, FAX RX IN MEMORY will appear in the display, alternating with OUT OF PAPER, FILM END, or PAPER JAM.
Chapter 5 Making Copies Your fax can also be used to make copies. Single and multiple copies (up to 99 per original) can be made, enabling your fax to double as a convenience office copier. 1 Load the document(s) face down. (Maximum of 10 pages.) The display will show: READY TO SEND • Set the resolution and/or contrast if RESOLUTION desired. (The default setting for copying is SUPER FINE.) 2 Press the COPY/HELP key.
Making Copies Press 1 (MULTI COPY) if you do not want the copies sorted. Press 2 (SORT COPY) if you want the copies sorted. Example of three copies each of three originals A B C A B C The display will show: 4 2 or Originals B C A A A B B B C C C ENTER # (01-99) If you are making one copy per original, press the START/MEMORY key. If you are making multiple copies per original, enter the number of copies per original (if the number is less than 10, enter a "0" before the number).
Making Copies Note: If you place a large number of originals in the feeder, the memory may become full before all of them can be scanned (MEMORY IS FULL will appear in the display). If this happens, press the START/MEMORY key to copy the originals which have been scanned, and then repeat the copy procedure for the remaining originals, including the original which was being scanned when the memory became full.
Chapter 6 Making Telephone Calls Your fax can be used like a regular telephone to make and receive voice calls. ♦ To make or receive a phone call, the power must be on. 1 2 Pick up the handset or press the SPEAKER key. Listen for the dial tone. Dial the number using one of the following methods: • Normal Dialing: Enter the full telephone number with the numeric keys. • Rapid Key Dialing: Press the SPEAKER or ABC 1 GHI 4 PQRS 7 2 JKL 5 TUV 8 DEF 3 MNO 6 WXYZ 9 appropriate Rapid Key.
Making Telephone Calls Comments: • While the handset of the fax is lifted (off hook), an extension phone connected directly to the fax cannot be used to speak with the other party. • The fax may interrupt a voice call received on an extension phone if the reception mode is set to TAD and there is a period of silence during the conversation. If you are on a touch-tone phone, you can prevent this by pressing any three keys on the phone immediately after you answer.
Making Telephone Calls Hold 6. Making Phone Calls You can put the other party on hold during a conversation by pressing the HOLD/SEARCH key. When this is done, they cannot hear you. You can put the handset back in the cradle without breaking the connection. When you are ready to speak with them again, pick up the handset. If you did not put the handset back in the cradle, press the HOLD/SEARCH key again to resume conversation.
Chapter 7 Special Functions Caller ID (Requires Subscription from Telephone Company) If you subscribe to a caller identification service from your telephone company, you can set your fax to display the name and number of the caller while the fax rings. Important: • To use this function, you must subscribe to a caller identification service from your telephone company. • Your fax may not be compatible with some caller identification services.
Caller ID 4 Press 1 to select SET. (To clear a previously programmed area code, press 2 and go to Step 7.) CLEAR SET 1 or 2 The display will show: ENTER AREA CODE 5 Enter the three digits of your area code. 2 0 5 (Example) 6 Press the START/MEMORY key to store your area code. START/MEMORY The display will show: 7 COVER SHEET Press the STOP key to return to the date and time display. STOP • Set Option Setting 2 (Number of Rings to Answer) to 2 or more rings (see Chapter 8).
Caller ID Display messages One of the following messages will appear while the fax rings if caller information is not available. NO SERVICE No caller information was received from your telephone company. Make sure that the telephone company has activated your service. CALLER-ID ERROR Noise on the telephone line prevented reception of caller information.
Caller ID 2 3 * Press the key to scroll through the list from the most recent call, or the # key to scroll through the list from the oldest call. or If you want to dial one of the numbers in the list, scroll through the list until the number appears in the display. • If you want to send a fax, load the START/MEMORY document and then press the START/MEMORY key. • If you want to make a voice call, pick up the handset or press the SPEAKER key. Dialing will begin automatically.
Caller ID 1 2 3 4 Press the keys shown at right. PRIORITY CALL # will appear in the display. FUNCTION 3 Press 1 to enter a number, or 2 to clear a number. (If you pressed 2, go to Step 4.) Enter the phone number, including the area code, by pressing the number keys (max. of 20 digits). 1 5 5 2 or 5 1 2 3 5 (Example) Press the START/MEMORY key and then the STOP key.
Distinctive Ring Distinctive Ring (Requires Subscription from Telephone Company) Important: • To use distinctive ring, you must subscribe to a distinctive ring service from your local phone company. Do not turn on this function if you do not subscribe to a distinctive ring service. • Your fax may not be compatible with some distinctive ring services. Distinctive ring is a service offered by some local telephone companies whereby they assign an additional second number to your regular single line.
Distinctive Ring 3 Press a number from 1 to 3 to select the ring pattern below that matches your second number’s ring pattern. Or, press 4 to have your fax automatically answer your normal telephone number. Press 5 to turn off the distinctive ring function. 1 RING PATTERN 1: Two short rings. 2 RING PATTERN 2: One short, one long, and one short ring. 3 RING PATTERN 3: Two short rings and one long ring. 4 STANDARD RING: Your standard (normal) ring pattern.
Broadcasting Broadcasting This function allows you to send the same document to as many as 20 different locations with just one operation. First store the document in memory, then enter the numbers of the receiving machines. The document will be transmitted to each location. ♦ You can only use Rapid Keys or Speed Dial numbers to dial the numbers of the receiving machines. 1 Load the document(s). The display will show: READY TO SEND 2 Press the START/MEMORY key and then 2.
Broadcasting 5 Press the START/MEMORY key. Transmission will begin. • A Transaction Report is automatically printed out after Broadcasting is completed. Check the "Note" column of the report to see if any of the locations are marked "Busy" or have a communication error code. If so, send the document to those locations again.
Cover Sheet Cover Sheet You can have the fax generate a cover sheet and send it as the last page of each of your fax transmissions. You can select a message. For the recipient’s name to appear, you must dial using a Speed Dial or Rapid Key number with the name programmed. Your name and number must be programmed as explained in Chapter 1. Follow the steps below to turn on the cover sheet function.
Cover Sheet 3 Press 1 (YES) to turn on the cover sheet function, or 2 (NO) to turn it off. The display will show: YES 1 NO or 2 AUTO PRINT OUT 4 Press the STOP key to return to the date and time display. STOP Selecting a header message (optional) When the cover sheet function is turned on, you can also select a message which will appear as a header at the top of the cover sheet. Note that the message selection is only effective for one transmission. 1 Load the document(s).
Cover Sheet 4 Select a message by entering a number from 1 to 4: 1: URGENT 2: IMPORTANT 3: CONFIDENTIAL 4: PLS. DISTRIBUTE 1 (Example) Dial the receiving machine and transmit the document. Note: To cancel a cover sheet header setting, press the STOP key or remove the document from the feeder. 7.
Batch Page Numbering Batch Page Numbering You can change the page numbering of the transmitted document from simple numbering ("P.01", "P.02", etc.) to batch numbering, which means that a slash and the total number of pages being sent are added after each page number (for example, "P. 01/05", "P.02/05", etc.). This allows the receiver to check for missing pages. 1 Load the document(s). • The document must be loaded before batch page numbering can be set.
Batch Page Numbering Comments: • If you need to cancel a batch number entry, remove the document from the feeder or press the STOP key. • If the number of pages actually transmitted does not coincide with the batch 7. Special Functions number entered, the alarm will sound and PAGE COUNT ERROR will appear in the display. PAGE E. will also appear in the NOTE column of the Transaction Report if it has been set to print out.
Blocking Reception of Unwanted Faxes Blocking Reception of Unwanted Faxes The Anti Junk Fax function allows you to block reception of faxes from parties which you specify. This saves paper by not printing out unwanted "junk" faxes. To use this function, first turn it on by setting Option Setting 11 to YES as explained in Chapter 8, and then enter the fax numbers from which you do not want to receive faxes as shown below. If you are using the Caller ID function, you can also enter voice numbers.
Blocking Reception of Unwanted Faxes 4 Enter the full number you want to block (max. of 20 digits). 5 5 5 1 2 3 4 (Example) 5 Press the START/MEMORY key. START/MEMORY Return to Step 3 to enter (or clear) another number, or press STOP to exit. STOP Step 3 or 7.
Sending Documents From Memory Sending Documents From Memory With this function, the original document is scanned immediately, stored in memory, and then transmitted once the connection to the receiving machine is made. This is convenient when transmitting to places where the line is often busy, as it saves you from waiting to pick up the original document and frees the feeder for other operations. After transmission, the document will be cleared from memory.
Sending Documents From Memory 3 Enter the number of the receiving machine using one of the following methods: • Press a Rapid Key. • Press the SPEED DIAL key and 01 02 03 (Example) enter a Speed Dial number. • Enter a full telephone number by pressing the number keys. 4 Press the START/MEMORY key if you entered a Speed Dial number or a full number. START/MEMORY • The document will be scanned and stored in memory.
Polling (Requesting a Fax Transmission) Polling (Requesting a Fax Transmission) Polling allows you to call another fax machine and have it send a document (previously loaded in its feeder) to your machine without operator assistance. In other words, the receiving fax machine, not the transmitting fax machine, initiates the transmission. You can use your machine to both poll and be polled by others. To use the polling function, you must first set Rapid Key 05/POLL for use as a polling key.
Polling (Requesting a Fax Transmission) Being polled (polling standby) To let another fax machine poll your machine, simply set the reception mode to FAX, and load the document(s) to be sent. Transmission will take place when the other fax machine calls your machine and activates polling. Automatic reception is possible while your machine is on polling standby. Polling security Polling Security allows you to prevent unauthorized polling of your machine.
Polling (Requesting a Fax Transmission) Storing and clearing fax numbers for polling permission You can store up to 10 fax numbers in your machine’s list of permitted numbers. 1 Press the keys shown at right. ENTRY MODE will appear in the display. 2 Press the # key four times. PASSCODE # MODE will appear in the display. 3 Press 1 to store a number, or 2 to clear a number. 4 Storing: Enter a 2-digit number from 01 to 10. This number identifies the fax number you will store in the next step.
Timer Operations Timer Operations The Timer function allows you to set a transmission and/or polling operation to be performed automatically at a time you specify. One transmission operation and one polling operation can be set at any one time, and the times they will be performed can be specified up to 24 hours in advance. As an example, you can use this function to take advantage of lower nighttime telephone rates without having to be there when the operation is performed.
Timer Operations 7 Enter the Speed Dial number of the receiving fax machine. 5 0 • If this is a polling operation, go to (Example) Step 10. 8 Press the START/MEMORY key. START/MEMORY 9 Adjust the resolution and/or contrast if desired (skip to the next step if you don’t want to change settings). 10 Press the START/MEMORY key and then the STOP key. If this is a transmission operation, load the document in the feeder sometime before the specified time of transmission.
Option Settings 8. Option Settings Chapter 8 The option settings let you customize your fax to better suit your needs. An initial setting has been made for each option at the factory. You can change a setting by following the steps described for each option below. FUNCTION First press FUNCTION and 4, then press # or to scroll through the options.
Option Settings Setting 2: NUMBER OF RINGS TO ANSWER This option sets the number of rings the fax machine waits before answering an incoming call in FAX reception mode. Enter any number from 1 to 5 rings. • Initial setting: 4 FUNCTION 4 Enter a number from 1 to 5 Press until display shows: NUMBER OF RINGS STOP RECALL INTERVAL Setting 3: RECALL INTERVAL This sets the amount of time your fax will wait between automatic redials when the line is busy. Enter 01 for 1 minute, 02 for 2 minutes, etc.
Setting 5: TEL/FAX REMOTE NUMBER If you hear a fax tone when you answer a call on a touch-tone extension phone connected to the same line as the fax, you can make the fax begin reception by pressing 5, , and on the phone. Use this setting if you want to use a number other than 5 to begin fax reception. You can enter any number from 0 to 9.
Option Settings Setting 7: TRANSACTION REPORT PRINT SELECT This sets the condition for printing out a Transaction Report. Enter a number from 1 to 5 as follows: 1 (ALWAYS PRINT): A report will be printed after each transmission, reception, or error. 2 (ERR/TIMER/MEM): A report will be printed after an error, timer operation, or memory operation. 3 (SEND ONLY): A report will be printed only after a transmission. 4 (NEVER PRINT): A report will never be printed.
Setting 9: DISTINCTIVE RING This sets the ring pattern to which your fax will answer if you subscribe to a distinctive ring service. Enter a number from 1 to 5 to select a pattern. See Distinctive Ring in Chapter 7 for more details.
Option Settings Setting 12: POLLING Press 1 if you want to use Rapid Key 05/POLL as a polling key. Press 2 if you want to use it as a regular Rapid Key. • Initial setting: 2 until display shows: FUNCTION 4 Press YES POLLING NO STOP or 1 2 CALLER-ID Setting 13: CALLER ID If you subscribe to a caller ID service and want to use the Caller ID function, press 1 twice, enter your 3-digit area code by pressing the number keys, and then press the START/MEMORY key. To turn Caller ID off, press 2.
8. Option Settings Option Settings Setting 14: AUTO COVER SHEET Press 1 (YES) to have the fax automatically generate a cover sheet and send it as the last page of each transmission. Press 2 (NO) to turn the function off. • Initial setting: 2 FUNCTION 4 YES Press until display COVER SHEET shows: NO STOP or 1 2 AUTO PRINT OUT Setting 15: ACTIVITY REPORT AUTO PRINT OUT Press 1 to have your fax automatically print out an Activity Report once every 30 operations.
Chapter 9 Printing Reports and Lists You can print out lists showing settings and information entered in the fax. You can also have the fax automatically print out a report on transactions after they are made. The lists and the report are described below. Printing a list 1 Press these keys: FUNCTION 2 The display will show: LISTING MODE 2 Press the # key or the display. * key until the desired list appears in the or 3 Press the START/MEMORY key.
Printing Reports and Lists be automatically printed out whenever information on 30 operations has accumulated. (A report can still be printed on demand at any time.) ♦ All information is erased after a report is printed out. If automatic print-out is turned off and print-out has not been done manually for 30 operations, the information on the oldest operation will be overwritten each time a new operation is performed.
Printing Reports and Lists COM.E-0 to COM.E-7 - A telephone line error prevented the transaction. See Line Error in Chapter 11. CANCEL - Transmission was cancelled because the STOP key was pressed, no document was in the feeder, or the other machine requested transmission using a function which your fax does not have. If you were attempting to fax, make sure a document is in the feeder. If you were receiving, contact the faxing party to see how they are trying to send to you.
Printing Reports and Lists Passcode List 9. Printing Lists This list shows settings made for polling security, your name and fax/telephone number as entered in the machine, and a sample of the header printed at the top of every page you transmit (HEADER PRINT). Option Setting List This list shows the current status of the option settings.
Printing Reports and Lists Anti Junk Number List This list shows the numbers that are blocked by the Anti Junk function. Caller ID List This list shows information about your most recent calls (maximum of 20 calls). (This list is only available if you are using the Caller ID function.
Printing Reports and Lists TAD Program List 9. Printing Lists This list shows the settings and codes programmed for the answering machine. Message List This list shows information about the messages currently recorded in the answering machine, including the date and time of recording, the length, and the type (ICM, memo, or 2-way).
Printing Reports and Lists Print Setup List This list shows the current status of the printing settings accessed by pressing the FUNCTION key and the 6 key. Transaction Report This report is printed out automatically after an operation is completed to allow you to check the result. Your fax is set at the factory to print out the report only when an error occurs. If desired, you can change the setting to have it printed out under a variety of other conditions.
Chapter 10 Maintenance Fax print head Clean the printing head frequently to assure optimum printing performance. Unplug the power cord. 2 Pull the paper release plate forward and remove the paper. 3 Open the operation panel (grasp the finger hold and pull up), and then pull the release on the right side of the machine forward to open the print compartment cover. 10.
Maintenance 4 Take the imaging film cartridge out of the print compartment and place it on a sheet of paper. 5 Wipe the print head and roller with denatured alcohol. Roller Print head Caution! • Do not use benzene or thinner. Avoid touching the print head with hard objects. • The print head may be hot if your fax machine has just received a large number of documents. If this is the case, allow the print head to cool prior to cleaning.
Maintenance Place the imaging film cartridge back in the print compartment. 7 Close the print compartment cover (press down on both sides to make sure it clicks into place), and then close the operation panel. 8 Reinsert the paper in the paper tray and push the paper release plate back down. 10.
Maintenance Scanning glass and rollers Clean the scanning glass and rollers frequently to ensure the quality of transmitted images and copies. Open the operation panel (grasp the finger hold and pull up), and wipe the scanning glass and rollers with a soft cloth. ♦ Make sure that all dirt and stains (such as correcting fluid) are removed, as dirts and stains will cause vertical lines on transmitted images and copies. ♦ Adhesive cellophane tape is useful for removal of debris from the rollers.
Chapter 11 Troubleshooting Problems and Solutions If you have any problems with your fax, first refer to the following troubleshooting guide. If you cannot solve the problem, call Sharp’s Customer Assistance Center at 1-800-BE SHARP. Line error Problem • Try the transaction again. If the error persists, check the following: 11.Troubleshooting LINE ERROR appears in the display and/or a transaction report is printed out with COM. E- and a number from 0 to 1, 2, 3, 4, 5, 6, or 7 in the NOTE column.
Problems and Solutions Dialing and transmission problems Problem Check and remedy No dial tone when you pick up the handset or press the SPEAKER key. • Make sure the handset cord is connected to the Dialing is not possible. correct jack. See Handset in Connections in Chapter 1. • Make sure the power cord is properly plugged into a power outlet. • Make sure that the telephone line is properly connected to both the TEL. LINE jack and the wall jack.
Problems and Solutions Reception and copying problems Problem Check and remedy • Make sure that the reception mode is set to The power is on, but no reception takes place. The printing paper comes out blank when you try to receive a document. FAX. If you subscribe to a distinctive ring service, make sure that the Distinctive Ring function is set to the correct ring pattern. If you do not subscribe to a distinctive ring service, make sure that Distinctive Ring is set to OFF SETTING.
Problems and Solutions • Any dirt or material on the scanning glass will The quality of copies is poor and/or black spots appear. Reception/copying is interrupted. cause spots to appear on copies and transmitted faxes. Clean the fax print head and the scanning glass as explained in Chapter 10. • If reception or copying takes place continuously for a long time, the print head may overheat. Turn off the power and let it cool down.
Problems and Solutions General problems Problem Check and remedy • Make sure the fax is plugged in and the imaging Information cannot be programmed in the fax. Nothing appears in the display. film and paper have been loaded. (Programming is not possible if the imaging film and printing paper have not been loaded.) See Loading the Imaging Film and Loading Printing Paper in Chapter 1. • Make sure the power cord is properly plugged into a power outlet.
Display Messages Messages and Signals Display messages Note: If you have turned on the Caller ID function, see Caller ID in Chapter 7 for display messages related to Caller ID. T.A.D. TRANSFER The answering machine’s transfer function has been turned on as explained in Transfer Function in Chapter 2. CHECK PAPER SIZE The paper size setting is incorrect. Change the paper size setting as described in Loading the Paper in Chapter 1.
Display Messages MEMORY IS FULL The memory is full. This may occur during fax reception if too much data is received before the pages can be printed out. If faxes have been received to memory because printing is not possible (an additional message will indicate the problem), resolve the problem so that printing can continue (see Substitue Reception to Memory in Chapter 3). If you are attempting to transmit from memory, see Sending Documents from Memory in Chapter 7.
Display Messages RECALLING This appears if you attempt to send a fax by automatic dialing and the line is busy or the receiving fax machine does not answer. Your fax machine will automatically reattempt the call. (See Automatic Redialing in Sending a Fax by Automatic Dialing in Chapter 2.) SEARCH DIAL The HOLD/SEARCH key has been pressed. Press # or to search for an automatic dialing number, or press STOP to return to the data and time display.
Clearing Paper Jams Clearing Paper Jams Clearing a jammed document If the original document doesn’t feed properly during transmission or copying, or DOCUMENT JAMMED appears in the display, first try pressing the START/MEMORY key. If the document doesn’t feed out, open the operation panel and remove it. 1 Open the operation panel by grasping the finger hold and pulling up. 2 Remove the document. 3 Close the operation panel, making sure it clicks into place. 11.
Clearing Paper Jams Clearing jammed printing paper 1 Pull the paper release plate forward and remove the paper. 2 Open the operation panel (grasp the finger hold and pull up), and then pull the release on the right side of the machine forward to open the print compartment cover. 3 Gently pull the jammed paper out of the machine, making sure no torn pieces of paper remain in the print compartment or rollers.
4 Close the print compartment cover (press down on both sides to make sure it clicks into place), and then close the operation panel. 5 Reinsert the paper in the paper tray and push the paper release plate back down. 11.
Ordering parts To order parts, contact the part distribution center located nearest you. When ordering a part, use the part order number shown below.
FCC Regulatory Information This equipment complies with FCC rules, Part 68. On this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. If requested, this information must be provided to your telephone company. An FCC compliant telephone cord and modular plug is provided with this equipment.
UX460U MSDS-Front 1/2 SHARP Date Issued: Dec. 22,1998 MATERIAL SAFETY DATA SHEET MSDS No. B-1006 Section 1. Product Identification Product Code: UX-3CR Imaging Film Section 2. Supplier’s Name and Address Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A.
UX300u MSDS-Front 2/2 SHARP Date Issued: Dec.22,1998 MATERIAL SAFETY DATA SHEET MSDS No. B-1006 Section 6. Physical Chemical Characteristics Boiling/Melting Point Vapor Pressure Vapor Density Evaporation Rate Appearance Odor m.p. about 70 C for ink not applicable not applicable negligible thin film coated with ink slight wax odor Specific Gravity about 1 Solubility in Water PH Viscosity Color negligible not applicable not applicable black Section 7.
Index A Activity Report, 118 Automatic printing, 117 Anti junk fax, 102, 115 Anti Junk Number List, 122 Audible signals, 136 Auto cover sheet, 117 Automatic dialing, 71 Automatic dialing, storing numbers, 68 B Batch page numbering, 100 Broadcasting, 95 C Caller ID, 88 Caller ID List, 90, 122 Calling Party Control detection, 43 Chain Dialing, 86 Cleaning, 125, 128 Contrast, 63 Copies, 82 Copy cut-off setting, 84 Copy/Help key, 10, 82 Cover sheet, 117 D Date, setting, 28 Daylight Saving Time, 30 Delete key
Index Loading printing paper, 22 Loading the document, 61 M Memory Sending documents from, 104 Substitute reception to, 81 Message List, 123 Messages Checking date and time, 40 Erasing, 39 Listening to, 38 Listening to remotely, 52 Setting allowed time, 41 N Normal Dialing, 65, 85 Number keys, 9 Number of rings in AUTO mode, 112 O Option Setting List, 121 Ordering parts, 140 Outgoing message, 34 Override Ringing, 48 P Panel release, 9 Paper jams, clearing, 138 Paper size setting, 23 Passcode List, 121
Index TEL. LINE jack, 14 TEL.
REMOTE OPERATION CARD The card below is provided as a quick guide to remote operation. Cut it out and carry it with you when you go out. Remote Operation Guide 1. Call your fax from a touch-tone telephone, and press # when the outgoing message begins. 2. Enter your remote code: . 3. Press # . 4. After listening to your messages, you can either hang up to save them, or enter one of the commands on the reverse side.
• • • • REMOTE COMMANDS • FAX RECEPTION MODES PLAYBACK Play messages. . . . . . . . . . Move backward/repeat. . . . Skip forward . . . . . . . . . . . . Stop . . . . . . . . . . . . . . . . . . Play new messages only . . (first stop playback) 7 # 2 # 5 # 0 # 6 # • ERASING MESSAGES Erase single message . . . . 3 # Erase all messages . . . . . . 3 3 # RECORDING A MEMO Start . . . . . . . . . . . . . . . . . . # End . . . . . . . . . . . . . . . . . . . 0 # RECORDING A NEW OGM Start . . . . . .
LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first end user purchaser that this Sharp brand product (the "Product"), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135 SHARP CORPORATION PRINTED IN THAILAND (TINSE4007XHZZ)
