UX-40DE FO-50DE SERVICE MANUAL No. 00ZUX40DE/SME FACSIMILE MODEL UX-40 FO-50 Illustration: UX-40 CONTENTS CHAPTER 1. GENERAL DESCRIPTION [1] Specifications ............................................ [2] Operation panel ......................................... [3] Transmittable documents .......................... [4] Installation ................................................. [5] Quick reference guide ............................... 1-1 1-2 1-3 1-4 1-8 CHAPTER 2. ADJUSTMENTS [1] Adjustments ..
UX-40DE FO-50DE CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s instructions.
UX-40DE FO-50DE CHAPTER 1. GENERAL DESCRIPTION [1] Specifications Automatic dialing: Rapid Key Dialing: 5 numbers Speed Dialing: 35 numbers Fax(thermal) paper: Initial starter roll (included with machine): 10 m Recommended replacement roll: FO-20PR, 30m Modem speed: 9600 bps with automatic fallback to lower speeds Transmission time* : Approx. 15 seconds Resolution: Horizontal: 8 dots/mm Vertical: Standard: 3.85 lines/mm Fine/Halftone: 7.7 lines/mm Super fine: 15.
UX-40DE FO-50DE [2] Operation panel 12 3 4 RECEPTION MODE FUNCTION TEL FAX TEL 6 7 5 RESOLUTION FAX DOWN VOLUME UP A.M. TEL/FAX ANRUFB. ABC 1 DEF ABC SPEED DIAL A GHI JKL C B D STOP REDIAL 03 04 PQRS 05 06 07 08 FUNKTION PQRS TUV WXYZ KOPIE/ HILFE HOLD/SEARCH START 2 4 MNO AUFLÖSUNG/ EMPFANGSART DEF JKL GHI LAUTSTÄRKE 01 02 E/ ABRUF 2 7 KURZWAHL 3STOP MNO 5 6 WXYZ TUV WAHLWDH. COPY/HELP 8 9 SYMBOLE 0 START ALPHAWAHL R LAUTSPR.
UX-40DE FO-50DE [3] Transmittable documents 5. Automatic Document Feeder Capacity 1. Document Sizes Number of pages that can be placed into the feeder at anytime is as follows: Normal size width length Normal size: max. ADF 5 sheets 148 – 216 mm 140 – 297 mm Special size: single sheet only (manual feed) NOTES: (Max.) (Max.) A4 size (Min.
UX-40DE FO-50DE 7. Use of Document Carrier Sheet TELEPHONE JACK A document carrier sheet must be used for the following documents. • Those with tears. A standard telephone jack must be located near the machine. This is the telephone jack commonly used in most homes and offices. • • • Those smaller than size 148mm (W) x 140mm (L). Carbon-backed documents Make print straight across paper E.G.
UX-40DE FO-50DE 4 Insert one end of the line cord into the socket on the back of the 4 Place the paper roll shims on each side of the paper compartment. machine marked TEL. LINE. Insert the other end into a wall telephone socket. • The ribbed side of the shims should face inwards (toward each other). N F N TE LI L. NE 5Unwrap the roll of thermal paper and place it in the compartment.
UX-40DE FO-50DE 4 Flip down the green levers on each side of the white roller. 4. Clearing a jammed document If the original document doesn’t feed properly during transmission or copying, or DOCUMENT JAMMED appears in the display, first try pressing the START key. If the document doesn’t feed out, open the operation panel and remove it. Important: Do not try to remove a document without first releasing it as explained below. This may damage the feeder mechanism.
4 Cut off the wrinkled part of the paper. 5. Clearing jammed paper UX-40DE FO-50DE If the fax paper jams, PAPER JAMMED will appear in the display. Follow the steps below to clear the jam. Grasp the finger hold and pull up to open the operation panel. 1 5 Reload the paper. • Jammed paper is often caused by improper loading. Be sure to carefully follow the instructions for paper loading given in Loading the Fax Paper. 2 Flip up the front paper guide. Note: Do not peel off or bend this strip of film.
UX-40DE FO-50DE SENDING FAXES [5] Quick reference guide ENTERING YOUR NAME AND NUMBER 1. Press: Place your document (up to 5 pages) face down in the document feeder. FUNKTION 3 Display shows: OWN NUMBER SET 2. Press: START 3. Enter your fax number (max. of 20 digits) by pressing the number keys. • To insert a space between digits, press the # key. To enter "+", press the • If you make a mistake, press the SPEED DIAL key to backspace and clear the mistake. 4. Press: key. Normal Dialing 1.
UX-40DE FO-50DE 3. Settings CHAPTER 2. ADJUSTMENTS Dial mode selector [1] Adjustments DIAL mode (Soft Switch No. SWB4 DATA No. 2) (step 1) Select "OPTION SETTING". General KEY : FUNCTION Since the following adjustments and settings are provided for this model, make adjustments and/or setup as necessary. DISPLAY: OPTION SETTING 4 OR # (step 2) Select "DIAL MODE". 1. Adjustments Adjustments of output voltage (FACTORY ONLY) KEY: 1. Install the power supply unit in the machine.
UX-40DE FO-50DE [2] Diagnostics and service soft switch 1. Operating procedure (1) Entering the diagnostic mode Press FUNC → 9 → → 8 → # → 7 , and the following display will appear. After 2 sec: DIAG MODE ROM Ver. FZP0 FZP0 Then press the START key and country name selected by country select will appear. Select the desired item with the with the direct key. Enter the mode with the START key.
UX-40DE FO-50DE 3. Diagnostic items description 3. 1. Soft switch mode 3. 6. Signal send mode This mode is used to send various signals to the circuit during FAX communication. Every push of START key sends a signal in the following sequence. Moreover, the signal sound is also output to the speaker when the line monitor of the soft switch is on. The soft switches are provided so that each operation mode can be set by using the operation panel. In this mode, these switches can be checked and set.
UX-40DE FO-50DE 3. 12. Country select This mode is used to set line connecting parameters which correspond to each destination. When the country select mode is selected, and then the START key is pressed, the destination (country name) currently set will be displayed. By pressing the # or key, selectable destinations (country names) are displayed. When the destination (country name) you want to choose is displayed, press the START key. Each parameter will be stored in RAM.
UX-40DE FO-50DE 5. Soft switch description • Soft switch SW NO. SW l A1 DATA NO. Switch setting and function ITEM 1 1 2 3 Protect from echo Forced 4800bps reception Footer Print No Yes Yes Yes No No 0 0 0 4 Length limitation of copy/send/receive No limit Copy/Send:60cm Receive:1.
UX-40DE FO-50DE SW NO. SW l A6 DATA NO.
UX-40DE FO-50DE SW NO. SW l B4 SW l B5 SW l B6 SW l B7 DATA NO. Switch setting and function ITEM 1 Dial pausing(sec/pause) 4 sec 2 sec 1 2 3 Dial mode Pulse → Tone change function by Tone Enable Pulse Disable 1 1 4 Dial pulse make/break ratio(%) 33/67 1 Auto dial mode 5 6 7 connect 8 Reserved Auto dial mode key 40/60 Delay timer of before line No. 5 No.
UX-40DE FO-50DE SW NO. SW l D2 SW l D3 SW l D4 DATA NO. Switch setting and function ITEM 1 1 2 Reserved Reserved 0 0 3 4 Reserved Reserved 0 0 5 Reserved 0 6 Caller ID function 7 Reserved 0 8 Reserved 0 1 CI off detection timer 2 (0~1550ms setting by 50ms step) Yes SW l E2 No 0 16 8 4 2 1 3 4 5 1 0 1 2 3 4 5 1 1 1 0 1 1 0 6 Reserved 0 7 Reserved 0 8 Reserved 0 1 DTMF type Caller ID RX level 2 (0~-44dBm setting by 1dBm step) No.
UX-40DE FO-50DE SW NO. DATA NO. Switch setting and function ITEM 1 DTMF detection time SW l F1 50ms 80ms 100ms 120ms 1 No. 1 0 0 1 1 0 2 3 No.
UX-40DE FO-50DE SW NO. SW l H1 SW l H2 SW l I1 SW l I2 SW l I3 SW l I4 DATA NO. ITEM 1 2 3 Busy tone continuous sound detect time Reserved Busy tone detect continuation sound detect 4 Reserved 5 Busy tone detect intermittent sound detect Busy tone detection pulse number Switch setting and function 1 Initial setting 0 5 sec 10 sec No Yes 1 0 0 0 No 2 pulses Yes 4 pulses 6 pulses 10 pulses 0 6 No. 6 0 0 1 1 0 7 8 1 No.
UX-40DE FO-50DE SW NO. SW l I5 SW l I6 SW l I7 SW l I8 DATA NO.
UX-40DE FO-50DE SW NO. DATA NO. SW l K1 1 Initial setting No. 1 Error 0 Send only 0 0 Always 0 2 No. 2 0 0 1 1 0 3 No.
UX-40DE FO-50DE SW-A3 No. 1, No. 2 CED tone signal interval • Soft switch function description For international communication, the 2100Hz CED tone may act as an echo suppression switch, causing a communication problem. Though SW-A3 No. 1 and No. 2 are normally set to 0, this selfing is used to change the time between the CED tone signal to eliminate the communication caused by echo. SW-A1 No. 1 Protect from echo Used to protect from echo in reception. SW-A1 No.
UX-40DE FO-50DE SW-A6 No. 2 End buzzer SW-B2 No. 7 Busy tone detection (After auto dial) Setting this bit to 0 will disable the end buzzer (including the error buzzer/ on-hook buzzer). Used to set YES/NO of busy tone detection after auto dialing. SW-A6 No. 3 Disconnect the line when DIS is received in RX mode Used for detection of busy tone in 2 or 4 pulses. SW-B2 No.
UX-40DE FO-50DE SW-B5 No. 1 ~ No. 3 Auto dial mode Delay timer of after line connect SW-C1 No. 5 Line density selection Used to set the transmission mode which is automatically selected when the Resolution key is not pressed. In the copy mode, however, the fine mode is automatically selected unless the Resolution key is manually set to another mode. Delay time between the line connection and dial data output under the auto dial mode. This setting is available when dial tone detection(SW-B2 No.
UX-40DE FO-50DE SW-D3 No. 1 ~ No. 5 CI off detection timer (0~1550ms setting by 50ms step) SW-E3 No. 1 Disconnect the line when DTMF "#" is received during TEL/FAX automatic switching mode Set the minimum time period of CI signal interruption which affords to be judged as a CI OFF section with 50ms steps. (Example) When set to "1", if machine detects the DTMF code # during phone/fax automatic switching mode, stop the pseudo ringer and disconnect the line.
UX-40DE FO-50DE SW-G3 No. 3, No. 4 Section time of quiet detection SW-J1 No. 2 Summer time setting The switch which sets the time from the start of detection function to the end of the function. Used to set YES/NO of automatic clock adjustment for Summer time. SW-G3 No. 5 ~ No. 8 Reserved Used to adjust ringing volume. SW-J1 No. 3, No. 4 Ringer Volume Set to "0" SW-J1 No. 5, No. 6 Speaker Volume SW-G4 No. 1 ~ No.
UX-40DE FO-50DE [3] Troubleshooting Refer to the following actions to troubleshoot any of the problems mentioned in 1-4. [1] A communication error occurs. [2] Image distortion produced. [3] Unable to do overseas communication. [4] Communication speed slow due to FALLBACK. • Increase the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5. May be used in case [1] [2] [3]. • Decrease the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5. May be used in case [3].
UX-40DE FO-50DE [4] Error code table 1. Communication error code table G3 Transmission Code Final received signal Error Condition (Receiver side) 0 Incomplete signal frame Cannot recognize bit stream after flag 1 NSF, DIS Cannot recognize DCS signal by echo etc.
UX-40DE FO-50DE 3-2. Automatic document feed CHAPTER 3. MECHANISM BLOCKS 1) Use of the paper feed roller and separation rubber plate ensures error-free transport and separation of documents. The plate spring presses the document to the paper feed roller to assure smooth feeding of the document. [1] General description 2) Document separation method: Separation rubber plate 1.
UX-40DE FO-50DE Separation rubber 5. Recording block Last page of document 5-1. General view ,,,,,,,,,, ,,,,,,,,,, ,,,,,,,,,, ,,,,,,,,,, ,,,,,,,,,, ,,,,,,,,,, ,,,,,,,,,, Back of document Recording paper Scanner frame First page of document Platen roller Feed plate PO guide Paper feed roller Fig. 4 3-5. Documents requiring use of document carrier 1) Documents smaller than 148mm x 140mm. Paper guide Head guide 2) Documents thinner than the thickness of 0.06mm.
UX-40DE FO-50DE [2] Disassembly and assembly procedures • • This chapter mainly describes the disassembly procedures. For the assembly procedures, reverse the disassembly procedures. • • The numbers in the illustration, the parts list and the flowchart in a same section are common to each other. Easy and simple disassembly/assembly procedures of some parts and units are omitted. For disassembly and assembly of such parts and units, refer to the Parts List.
UX-40DE FO-50DE 2 Parts list (Fig. 2) CIS unit and scanner frame No. 1 18 19 2 3 4 5 6 7 8 9 10 Q’ty No.
UX-40DE FO-50DE 3 Operation panel unit, drive unit, hopper guide Parts list (Fig. 3) No. Q’ty No.
UX-40DE FO-50DE Upper cabinet and document guide upper 4 Parts list (Fig. 4) No. Q’ty No.
UX-40DE FO-50DE 5 Parts list (Fig. 5) Drive unit frame No. Q’ty No.
UX-40DE FO-50DE Parts list (Fig. 6) Release lever, head guide and PO guide 6 No. 1 2 3 4 E AS LE RE 4 5 1 2 3 Fig.
UX-40DE FO-50DE 7 Head frame unit Parts list (Fig. 7) No. 1 2 Screw (3×6) 1 3 Connector 1 4 Screw (3×8) 1 5 Head earth cable 1 6 Head frame unit 1 7 Screw (3×8) 2 8 Panel lock lever spring 2 5 6 4 3 5 7 1 8 Control 7 PWB 8 Fig.
UX-40DE FO-50DE 8 Parts list (Fig. 8) Head frame and thermal head No. 1 2 3 4 5 6 7 8 9 Q’ty No. 1 Platen gear Part name 1 7 Screw (3×6) Part name Q’ty 1 2 Platen bearing 2 8 Head holder, right 1 3 Platen roller 1 9 Thermal head 1 4 Connector 1 10 Head spring 2 2 5 Screw (3×6) 1 11 Head spring 1 3 6 Head holder, left 1 12 Head frame 1 12 2 10 3 11 1 6 9 2 5 4 12 10 8 11 7 10 Fig.
UX-40DE FO-50DE 9 PWB case top, bottom, PWB and speaker Parts list (Fig. 9) No. Q’ty No.
UX-40DE FO-50DE 10 Wire treatment Parts list (Fig. 10) No. Part name Q’ty 1 Core (F2064) 2 2 Screw (3×6) 1 3 Screw (4×6) 1 4 Screw (3×6) 1 5 Band 1 6 Core (F2063) 1 7 Screw (3x8) 1 Door sensor cable Rib Panel cable Door sensor cable Rib Operation panel PWB Panel cable Rib Door sensor cable Hopper cover Operation panel unit The panel cable, door sensor cable, cam switch cable and motor cable pass to the core 2 times.
4–1 LINE HANDSET SPEAKER SURGE PROTECT/ FILTER AMPLIFIER AMPLIFIER CML AMPLIFIER D-FF CI TRANSFORMER BZ TEL/LIU PWB UNIT CLOCK 32.
16 4–2 OPERATION PANEL PWB UNIT CNLCD 2 16 CNDR CNCIS CNTH CNPN CNMT 6 FRONT SENSOR 2 CNFRS CONTROL PWB UNIT CNCSW 2 CAM SW SPEAKER 2 CNSP CNPW TEL/LIU PWB UNIT CNTNJ CNLNJ POWER SUPPLY PWB UNIT CN2 CNLIUB CNLIUB 8 CNLIUA CNLIUA 5 12 ARG CNHJ HANDSET AC CORD [2] Wiring diagram 14 LCD UNIT DOOR SENSOR 7 CIS(CONTACT IMAGE SENSOR)UNIT FG THERMAL HEAD TX/RX MOTOR FG UX-40DE FO-50DE CNPN
UX-40DE FO-50DE [3] Point- to-point diagram CNMT TX/RX MOTOR THERMAL HEAD OPERATION PANEL PWB CIS TPAD TPBD TPAD TPBD VMT VMT VTH VTH STRB1 STRB2 THI N.C.
UX-40DE FO-50DE 3. Operational description CHAPTER 5. CIRCUIT DESCRIPTION Operational descriptions are given below: • [1] Circuit description When a document is loaded in standby mode, the state of the document sensor is sensed via the 1 chip fax engine (FC200). If the sensor signal was on, the motor is started to bring the document into the standby position. With depression of the START key in the off-hook state, transmission takes place.
UX-40DE FO-50DE 3) 27E010 (IC5): pin-32 DIP (ROM) [2] Circuit description of control PWB ROM of 1 Mbit equipped with software for the main CPU. 1. General description 4) W24258S-70LE (IC3): pin-28 SOP (SRAM) Fig. 2 shows the functional blocks of the control PWB, which is composed of 4 blocks. Line memory for the main CPU system RAM area and coding/decoding process. Used as the transmission buffer. MAIN CONTROL BLOCK Memory of recorded data such as daily report and auto dials.
UX-40DE FO-50DE FC200 (IC2) Terminal descriptions Pin No. I/O Input Type 135 133 130 I I O HU H − A[23:0] [15:20][22:27] D[7:0] [141:144] RDn WRn ROMCSn CS1n CS0n MCSn SYNC REGDMA WAITn RASn CAS[1:0]n DWRn [1:6][8:13] O TU CPU Control Interface − Modem interrupt, active low. (Hysteresis In, Internal Pullup.) − System clock. (Hysteresis In.) 123XT Test clock. Bus Control Interface 123XT Address bus (24-bit).
UX-40DE FO-50DE FC200 (IC2) Terminal descriptions Pin Name Pin No.
UX-40DE FO-50DE (2) Panel control block The following controls are performed by the FC200.
UX-40DE FO-50DE (4) Modem (FM209) block FEATURES INTRODUCTION • The CONEXANT FM209 MONOFAX modem is a synchronous 9600 bits per second (bps) half-duplex modem with error detection and DTMF reception. It has low power consumption and requires a single +5V and +3.3V DC power supply. The modem is housed in a single VLSI device package. The modem can operate over the public switched telephone network (PSTN) through line terminations provided by a data access arrangement (DAA).
UX-40DE FO-50DE FM209 (IC4) Hardware Interface Signals Pin Signals – 128-Pin TQFP Pin No.
UX-40DE FO-50DE FM209 (IC4) Hardware Interface Signals Pin Signals – 128-Pin TQFP Pin No.
UX-40DE FO-50DE [3] Circuit description of TEL/LIU PWB (1) TEL/LIU block operational description 1) Block diagram TEL/LIU PWB SP OUT ENABLE CONTROL PWB TXOUT RTLOOP SPKRP-P L1 CML C M (0:1) (1:0) (0:0) (1:1) MIC ENABLE SIN DAC SP DRIVER L2 B DAC GAIN 0,6dB CI DPON H ~ + ~ – L DPON DPMUTE H RXIN HS MIC GAIN MICP MIC IN LPF MIC 1 ENABLE 0 0,20,25,30dB L ADC TELIN LINEIN LINE IN LPF LINE IN 1 ENABLE SOUT ADC GAIN 0,–4dB 0 RHS HANDSET RANK RX DRSNS TELMUTE TX LINE DRIVER TELO
UX-40DE FO-50DE 5. Externally connected TEL OFF HOOK detection circuit section • 4) Signal selection The following signals are used to control the transmission line of TEL/ FAX signal. For details, refer to the signal selector matrix table. The circuit current detection is turned on together with OFF HOOK of main body or OFF HOOK of externally connected TEL. ON of CML OFF (HS=L) is judged as OFF HOOK of externally connected TEL. [Control signals from output port] 6.
UX-40DE FO-50DE [Signals for status recognition according to input signals] Signal Name Function H:The handset is in the on-hook state. RHS L: The handset is in the off-hook state. CI Incoming call (CI) detection signal [Other signals] Signal Name TEL IN NO Signal Name (CNLIUA) NO Signal Name (CNLIUA) 1 TELOUT 7 RXIN 2 3 TELIN TELMUTE 8 9 TXOUT CML 4 5 CI 10 11 +5V HS 6 RHS 12 DG +24V NO Signal Name (CNLIUB) NO Signal Name (CNLIUB) 1 RLYCNT N. C.
UX-40DE FO-50DE [4] Circuit description of power supply PWB 1. Block diagram F1 1.6A/250V Noise Filter Circuit AC IN Rectifying Smoothing Circuit Switching Circuit (RCC system) F2 1.6A/250V Regulator Circuit +5V +24V Control Circuit Photo Coupler Fig. 8 2-1. Noise filter circuit 2-4. Control circuit The input noise filter section is composed of L1, C1, C15 and C21 which reduces normal mode noise from the AC line and common mode noise to the AC line.
6–1 R120 150 R122 470 OPI0 OPI1 OPI2 OPI3 LEDCTL LCDCS OPO0 OPO1 OPO2 OPO3 OPO4 OPO5 OPO6 C154 C155 C133 C134 C177 C176 C178 VDRAM 114 22P 22P 22P 22P 22P 22P 22P DG C174 22P +VREF –VREF VIN THADI C171 1 BZOUT 52 51 RA9 470 x 4 50 49 55 L107 R152 54 HM601 120 47 46 RA15 44 470 x 4 43 42 40 39 38 KEN1A KEN2A KEN3A KEN4A E SEN0 SEN1 SEN2 SEN3 SEN4 SEN5 SEN6 SEN7 CA2 F X2 32.
6–2 1 2 3 4 5 6 A Memory block A (1-3I) (1-3I) (1-6I) (1-5I) B ROMCS RD D[7~0] A[16~0] B A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 2 3 29 28 4 25 23 26 27 5 6 7 8 9 10 11 12 22 24 C A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 E G 21 20 19 18 17 15 14 13 GND 16 31 (A17) 32 VCC 1 VPP DQ8 DQ7 DQ6 DQ5 DQ4 DQ3 DQ2 DQ1 IC5 27E010 ROM C DG C205 0.
6–3 IC1 WT74 B (1-1D) C109 R130 R116 R143 R189 C DG R115 270 L100 HM601 DG C108 0.01 R139 470 119 XCLK 24 YCLK 115 RESET 13 EN85 111 110 109 105 104 102 101 99 TELMUTE TXMUTE TXMUTE D C208 100P DG 8 EYEXY 4 EYECLK 3 EYESYNC E DG DG DG F DG DG DG 29 122 54 50 75 26 30 55 9 76 25 51 31 18 56 27 52 6 C217 100P R131 10K 32 N.C./IARESET-S 57 IARESET-P DG G DG R101 120 C104 10P X1 32.256MHz 116 R147 470 VC-P N.C. RESERVED N.C./MICP-S N.C./MICM-S N.C./MICBIAS-S N.C./SPKRP-S N.C.
6–4 A CNCUT -2 N.M. CNCUT -3 CNCUT-1 CNPN-12 CNFRS-2 CNFRS-1 CNCSW-2 CNCSW-1 DG +24V N.C. DG CUT ORGSNS DG FRSNS DG CSW R128 0 R169 1K B 4 N.M. PI2 SG206 PI1 3 DG DG 2 1 4 2 DG 3 DG N.M. 1 C139 DG C180 2200P DG C122 2200P DG C120 2200P C C PSNS PESNS PSNS PESNS CUTI ORGSNSI FRSNSI CSWI D (1-3A) (1-4A) (1-5A) (1-3A) (1-3A) (1-4A) D E E CNPW-3 CNPW-4 CNPW-5 CNPW-6 CNPW-1 CNPW-7 CNPW-2 DG F MG MG +24V +24V DG DG +5V BAT1 CR2032 F N.M.
6–5 A (1-5A) VREFCONT DG R180 20K +24V +5V DG DG N.M. C135 0.1 C137 0.1 DG DG C Q5 2SA1037 R148 5.1K DG C159 1 DG DG +5V C10 N.M.
6–6 1 A R176 47K +5VA C198 1 B R156 0 R175 118K DG +5VA +5V Q3 PDTC114 C197 0.1 6 – 5 + +24VA Q6 PDTC114 DG 4 8 DG 2 – 3 + 7 C N.M. R174 R173 30K DG R157 3.3K TXMUTE SIGTX 1 R170 51K IC7 2904 DG C193 1 IC7 2904 C182 33P DG R159 118K DG L109 0 R154 100 C9 47/25 R172 15K C179 (1-1D) C223 0.1 C186 1 C192 1 N.M. RCVOL RXIN TXOUT TELOUT C195 820P R153 6.8K C194 0.022 C185 1 (3-1D) (3-4H) R160 0 DG R171 3.
UX-40DE FO-50DE Control PWB parts layout (Top side) 6–7
UX-40DE FO-50DE Control PWB parts layout (Bottom side) 6–8
6–9 1 CNHJ-3 CNHJ-2 JP10 N.M. D3 1N4148 B D2 1N4148 DG R116 10K +5V DG C C112 DG R122 10K DG C107 1000P DG IC101 2904 7 IC101 2904 R117 16K 1 N.M. D DG – 6 + 5 + – R128 8.2K R125 24K C10 2.2/50 R129 3.3K N.M. PC4 DG ~ ~ REC1 S1ZB60 R1 0 ZD5 C110 2200P R124 47K N.M. C108 2 – 3 + C111 1000P ZD4 PC6 TLP521 DG R123 3.3K C9 D1 1N4148 R102 120K R2 47K(1/2W) ZD3 BZX79B20V VREF R119 150 Q101 BC847B C7 4.7/50 C106 0.047 C3 0.
6 – 10 1 2 3 4 5 6 B A +5V DG R153 470 R152 100K R150 R151 R149 470 R148 470 PC5 TLP521 B SW1 HOOK SW DG DG PC6 TLP521 PC1 PC4 PC3 TLP627 C127 0.01 PC2 TLP627 TEL/LIU PWB circuit A DG DG C126 0.1 C125 0.1 DG Q107 DG Q109 DG Q110 PDTC114 DG Q108 PDTC114 N.M. RHS HS CI RLYCNT N.M. E-RLY DPMUTE DPON C CNHS-2 CNHS-1 CNLIUA-6 CNLIUA-5 CNLIUA-4 CNLIUB-1 CNLIUB-5 CNLIUB-4 CNLIUB-3 C D Q105 N.M.
UX-40DE FO-50DE TEL/LIU PWB parts layout (Top side) 6 – 11
UX-40DE FO-50DE TEL/LIU PWB parts layout (Bottom side) 6 – 12
6 – 13 A 1 F1 1.6A/250V 2 -50.0V -25.00us C7 3900P F2 1.6A/250V CH2 W1 50.0V CN1 C1 0.22 R1 3.3M V1 ERZV07D471 L1 ELF15N003A C21 TH1 89.2 GND B 25.00us -50.0V -25.00us C D 5us/div 25.00us D6 N.M. 5us/div C17 1000P PC1 10V/div CH2 W1 50.0V C24 0.22 R7 D5 33 1SS355 C6 0 C10 2200/16 D8 SR140 FB1 25.00us R15 330K R14 1.5K Q5 2SC4210 PC2 PC123YS ZD7 RD20ESAB ZD5 RD6.2SB Q4 2SC2412K R13 4.
UX-40DE FO-50DE Power supply PWB parts layout (Top side) T1 Q1 D9 J7 R10 C3 D7 J3 C8 C2 L1 C13 ZD6 V1 J5 C10 FB1 D8 IC1 R24 ZD7 L2 C7 C16 L3 VR1 2 D4 F1 TH1 R2 R3 J1 PC2 C9 1 D1 PC1 CN2 C24 D3 8 CN1 C1 J4 ZD4 1 R1 C15 C21 D2 F2 J6 J12 J11 J10 JW1 R4 C4 C23 R9 ZD1 R11 R15 R16 C12 Q2 R25 C5 R14 D6 R13 R17 Q6 R12 R21 R19 6 – 14 R20 C17 Q5 C6 R7 R5 ZD2 ZD5 F3 Q4 R18 D5 R6 Q3 R8 Power supply PWB parts layout (Bottom side)
6 – 15 1 2 3 4 5 6 B KEN1A KEN2A KEN3A KEN4A SEN7 SEN6 SEN5 SEN4 RS SEN3 LD7 SEN2 LD6 SEN1 LD5 SEN0 N.M. D8 D7 1SS270 D6 1SS270 D1 1SS270 D5 1SS270 D2 1SS270 D3 1SS270 D4 1SS270 REC REDIAL 05 01 RESO/MODE FUNC VOLUME C REPEAT SPEED START 02 7 4 1 D A B C D NOTE: Since the parts of PWB cannot be supplied, change it as a unit.
UX-40DE FO-50DE CHAPTER 7.
UX-40DE FO-50DE [2] Power on sequence START CPU initialized MODEM initialized “WAIT A MOMENT” display STOP key ? NO “MEMORY CLEAR ?” display NO 3 sec ? YES 1 YES STAND-BY START key ? NO 2 YES COPY key ? 1 2 “MEMORY CLEARED” display “MEMORY CLEARED” display Memory clear Memory clear STAND-BY PROCESS CHECK MODE NO YES STOP key ? NO 3 sec ? NO YES STAND-BY 7–2
UX-40DE FO-50DE CHAPTER 8. OTHERS [1] Service tools 1. List NO. PARTS CODE 1 2 CPWBS3045SCS1 PSHEZ3354SCZZ DESCRIPTION Q’TY Extension board unit (Control PWB) Shading wave memory standard paper 1 1 PRICE RANK AR AD Extension board unit EXTENSION CONTROL PWB C17 DG1 PESNS EC PI2 R145 (BOTTOM SIDE) A K PI1 A K E C PSNS DESCRIPTION Q’TY PRICE RANK NO.
UX-40DE FO-50DE 2. Description 2-1. Relay board unit 1. Remove the TEL/LIU PWB, control PWB and Power Supply PWB from this unit, and mount the relay board unit instead. • Before connecting the wiring to the relay board unit, set the test PWB switches to the fixed position. 2. The setting is as follows. • The relay cables are used as one pair. • The cover swich and hook switch are manually operated.
UX-40DE FO-50DE 3. Shading paper The white and black basis is applied to remember the shading waveform. Be sure to perform this operation when replacing the battery or replacing the control PWB. Execute in the shading mode of DIAG mode.
UX-40DE FO-50DE [2] IC signal name CONTROL PWB UNIT IC101: VHiXC61AN45M1 (XC61AN4502ML) VIN 3 VIN 3 1 VOUT VREF 1 VOUT 2 VSS 2 VSS REG100: VHi62FP332P-1 (XC62FP3302P) VIN 2 3 VOUT CURRENT LIMITER + – VSS 1 PEFERENCE VOLTAGE SOURCE 1 VSS 8–4 VIN VOUT 3 2
UX-40DE FO-50DE IC5: VHiW27E010-12 (27E010) ROM IC3: VHiW24258S7LE (W24258S-70LE) (TOP VIEW) (TOP VIEW) A14 1 28 VDD A12 2 27 WE A7 3 A6 A5 1 32 VCC 26 A13 A16 2 31 PGM 4 25 A8 A15 5 24 A9 A4 6 23 A11 A3 7 22 OE A2 8 21 A10 Pin name Signal A1 9 20 CS A0~A14 CS Address input VPP Chip select input A0 10 19 I/O8 WE Write enable input I/O1 11 18 I/O7 OE Output enable input I/O2 12 17 I/O6 I/O3 13 16 I/O5 VSS 14 15 I/O4 I/O1~I/O8 Data I/O VDD Power source
STRBPOL 37 8–6 ADGD 72 +VREF 71 ADVA 70 ADGA 69 ADXG 68 VIN 67 –VREF/CLREF 66 THAD1 65 VSS 64 VBAT 63 PWRDWNN 62 BATRSTN 61 XOUT 60 XIN 59 TEST 58 CS0N 57 VSS 56 LEDCTL/GPIO16 55 VCDCS/GPIO17 54 VSS 53 OPI0/GPIO21/SSRXD1 52 OPI1/GPIO22/SSTAT1 51 OPI2/GPIO23/SSCLK1 50 OPI3/GPIO24 49 VDD 48 OPO0/GPO8/SMPWRCTRL 47 OPO1/GPO9/PMPWRCTRL 46 VSS 45 OPO2/GPO10/RINGER 44 OPO3/GPO11 43 OPO4/GPO12/SSTXD1 42 VDD 41 OPO5/GPO13 40 OPO6G/PO14 39 OPO7/GPO15 38 109 DWRN 110 CAS2N 111 CAS
UX-40DE FO-50DE IC4: VHiFC2FM209-1 (FM209) RESERVED GPO4 GPO3 DGND4 CTS# IRQ1# GPO2 GPO1 GPO0 VDD5 VGG DGND5 RESET# XTLI XTLO RESERVED XCLK GPI1 IRQ2# SR3IN RESERVED RESERVED DGND6 DVAA AGND5 RESERVED 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 SR4IN1/RESERVED2 1 102 GPO5 SR3OUT1/RESERVED2 2 101 GPO6 EYESYNC 3 100 VDD4 EYECLK 4 99 GPO7 RXD 5 98 GPI7 SR1IO 6 97 GPI6 NC 7 9
UX-40DE FO-50DE PARTS GUIDE MODEL UX-40 FO-50 CONTENTS 1 Cabinet, etc. 6 Packing material & Accessories 2 Scanner unit 7 Control PWB unit 3 Upper cabinet 8 TEL-Liu PWB unit 4 Document guide upper 9 Power supply PWB unit 5 Drive unit Index Because parts marked with " " is indispensable for the machine safety maintenance and operation, it must be replaced with the parts specific to the product specification.
UX-40DE FO-50DE [1] Cabinet, etc.
UX-40DE FO-50DE PARTS CODE NO. PRICE RANK NEW MARK PART RANK N N N N E E C C C C C C C C C B C D D C C E C C C C C B E C C C C C C C C C C C C C C C B E C C C C C B D D C C C C C C DESCRIPTION [1] Cabinet etc.
UX-40DE FO-50DE [2] Scanner unit 13 12 19 5 1 15 10 11 20 19 15 16 20 16 2 2 8 7 9 5 20 1 15 16 17 16 6 15 2 3 6 14 19 18 4 NO.
UX-40DE FO-50DE [3] Upper cabinet 6 5 4 3 1 7 B2x3 NO.
UX-40DE FO-50DE [5] Drive unit 22 2 B3 20 21 6 17 9 12 9 1 13 15 10 4 12 9 PARTS CODE NO.
UX-40DE FO-50DE [6] Packing material & Accessories 5 17 16 24 3 1 25 TAPE TAPE 4 AC CORD ORIGINAL DOCUMENT SUPPORT SIDE 9 23 11 2 FAX PAPER 7 6 TAPE (1) TAPE R (3) (4) (2) 8 NO.
UX-40DE FO-50DE NO.
UX-40DE FO-50DE NO.
UX-40DE FO-50DE NO.
UX-40DE FO-50DE NO.
UX-40DE FO-50DE NO.
UX-40DE FO-50DE NO.
UX-40DE FO-50DE Index PARTS CODE [C] CCNW-212AXH01 ″ CCNW-215AFF01 CPWBX3084FF01 ″ [D] DCEKK201CFF01 ″ DCEKK201CFF02 ″ DCEKL227CFF01 ″ DCEKP203CFF01 DUNTK204CFFBG DUNTK204CFFWH [G] GCABA2342FFSR GCABA2342FFSS GCABB2343FFSA GCABB2343FFSC GCASP2110XHSD GCASP2110XHSE GCASP2111XHSA GCASP2111XHSC GDAI-2082XHSA GDAI-2082XHSC GDAI-2083FFZZ [H] HPNLH2392XHSV HPNLH2392XHS4 [J] JBTN-2257FFSA JBTN-2257FFSC JBTN-2258FFSA JBTN-2258FFSC JBTN-2261FFSA JBTN-2261FFSC [L] LBSHP2110XHZZ LBSHP2112XHZZ LFRM-2207XHZZ LFRM-2208F
UX-40DE FO-50DE PARTS CODE No.
UX-40DE FO-50DE PARTS CODE No.
