Service manual

ManualsBrandsSharp ManualsFaxesUX-P100

UX-P100U

UX-P200U

No. 00ZUXP100USME

CHAPTER 1. GENERAL DESCRIPTION

[1] Specifications ............................................ 1-1

[2] Operation Panel

....... ................................. 1-2

[3] Transmittable documents .......................... 1-3

[4] Installation ................................................. 1-4

[5] Quick setup guide ..................................... 1-8

[6] Quick reference guide ............................... 1-9

[7] Option imaging film specifications

(UX-5CR) ............................................1-9

CHAPTER 2. ADJUSTMENTS

[1] Adjustments............................................... 2-1

[2] Diagnostics and service soft switch .......... 2-2

[3] Troubleshooting....................................... 2-19

[4] Error code table....................................... 2-20

CHAPTER 3. MECHANISM BLOCKS

[1] General description .................................. 3-1

[2] Disassembly and assembly

procedures ....................................... 3-3

CHAPTER 4. DIAGRAMS

[1] Block diagram ............................................4-1

[2] Wiring diagram .......................................... 4-2

[3] Point-to-point diagram ............................... 4-3

CHAPTER 5. CIRCUIT DESCRIPTION

[1] Circuit description...................................... 5-1

[2] Circuit description of control PWB..............5-2

[3] Circuit description of TEL/LIU PWB .......... 5-9

[4] Circuit description of

power supply PWB ............................5-12

[5] Circuit description of CIS unit ...................5-12

CHAPTER 6. CIRCUIT SCHEMATICS AND

PARTS LAYOUT

[1] Control PWB circuit ................................... 6-1

[2] TEL/LIU PWB circuit ................................. 6-9

[3] Power supply PWB circuit ....................... 6-11

[4] Operation panel PWB circuit ................... 6-13

[5] Interface PWB circuit............................... 6-15

CHAPTER 7. OPERATION FLOWCHART

[1] Protocol ..................................................... 7-1

[2] Power on sequence .................................. 7-2

CHAPTER 8. OTHERS

[1] Service tools.............................................. 8-1

[2] IC signal name .......................................... 8-4

[3] Changing the record paper size ................ 8-5

PARTS GUIDE

CONTENTS

FACSIMILE

UX-P100

UX-P200

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for

maintaining the safety and performance of the set.

This document has been published to be used

for after sales service only.

The contents are subject to change without notice.

SHARP CORPORATION

SERVICE MANUAL

Illustration: UX-P100U

SELECTION CODE DESTINATION

UX-P100U (Open LCR)

U.S.A.

UX-P200U

U.S.A.

MODEL

Summary of content (92 pages)

PAGE 1
UX-P100U UX-P200U SERVICE MANUAL No. 00ZUXP100USME FACSIMILE UX-P100 MODEL UX-P200 SELECTION CODE UX-P100U (Open LCR) UX-P200U DESTINATION U.S.A. U.S.A. Illustration: UX-P100U CONTENTS CHAPTER 1. GENERAL DESCRIPTION [1] Specifications ............................................ 1-1 [2] Operation Panel ....... ................................. 1-2 [3] Transmittable documents .......................... 1-3 [4] Installation ................................................. 1-4 [5] Quick setup guide .....
PAGE 2
UX-P100U UX-P200U CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s instructions.
PAGE 3
UX-P100U UX-P200U CHAPTER 1. GENERAL DESCRIPTION [1] Specifications Automatic dialing: 30 numbers Imaging film: Initial starter roll:UX-P100U (included with machine): 32 ft. (10 m) (approx. 30 letter-size pages) Input document size: Automatic feeding: Width: 5.8 to 8.5" (148 to 216 mm) Length: 5.5 to 11" (140 to 279 mm) Manual feeding: Width: 5.8 to 8.5" (148 to 216 mm) Length: 5.5 to 23.6" (140 to 600 mm) Effective scanning width: 8.3" (210 mm) max. Effective printing width: 8.3" (210 mm) max.
PAGE 4
UX-P100U UX-P200U [2] Operation panel 1 4 3 2 ABC UP 1 TEL FAX GHI Z STOP COPY/HELP START/MEMORY FUNCTION JKL PQRS RESOLUTION/ REDIAL RECEPTION MODE 7 OpenLCR DEF 2 4 A SPEAKER 5 3 MNO 5 6 WXYZ TUV 8 9 0 DOWN Illustration: UX-P100U 6 7 8 9 10 11 1. Display 12 8. START/MEMORY key This displays messages and prompts to help you operate the machine. 2. RESOLUTION / RECEPTION MODE key Press this key after dialing to begin fax transmission.
PAGE 5
UX-P100U UX-P200U [3] Transmittable documents 5. Automatic Document Feeder Capacity 1. Document Sizes Number of pages that can be placed into the feeder at anytime is as follows: Normal size width length Normal size: max. ADF 10 pages 5.8" - 8.5" (148 – 216 mm) 5.5" - 11" (140 – 279 mm) Special size: single sheet only (manual feed) NOTES: (Max.) (Max.) Letter size (Min.
PAGE 6
UX-P100U UX-P200U 7. Use of Document Carrier Sheet TELEPHONE JACK A document carrier sheet must be used for the following documents. • Those with tears. A standard RJ11C single-line wall telephone jack must be located near the machine. This is the telephone jack commonly used in most homes and offices. • Those smaller than size 5.8" (W) x 5.5" (L) (148mm (W) x 140mm (L)). • Carbon-backed documents • Make print straight across paper E.G.
PAGE 7
UX-P100U UX-P200U 4 Remove the new roll of Imaging Film from its packaging. 3. Assembly and connections 1 Connect the Handset as shown and place it on the Handset Rest. • Cut the band that holds rolls together. ♦ The ends of the Handset Cord are identical, so they will go into either jack. Make sure the Handset Cord goes into the jack marked with a Handset symbol on the side of the machine! 5 Insert the green gears. Make sure the gears fit into the slots in the ends of the rolls.
PAGE 8
UX-P100U UX-P200U 3 Setting the paper size. 4 Attach the Paper Tray and Paper Tray Extension. The fax has been set at the factory to scale received faxes to letter size paper. If you loaded legal paper, you must change the paper size setting to LEGAL. Note: The Paper Tray Extension has a top side and a bottom side. If you cannot insert the tabs into the holes, turn the support over. Display: 1. Press Insert horizontally and rotate up. FUNCTION once and 2. Press once and 3. Press once. twice.
PAGE 9
UX-P100U UX-P200U 5. Clearing a jammed original document 6. Clearing jammed printing paper 1 Open the Operation Panel (press 1 If the original document doesn’t feed properly during transmission or copying, or DOCUMENT JAMMED appears in the display, first try pressing the START/MEMORY key. If the document doesn’t feed out, remove it as described below. ). Important: Do not try to remove a jammed document without releasing it as described below. This may damage the feeder mechanism.
PAGE 10
UX-P100U UX-P200U [5] Quick setup guide 1 Connect the Handset and place it on the Handset Rest. Note: To enter your name and fax number and set the date and time so that they appear at the top of each fax you send, see pages 16 - 19 of the Operation Manual. 2 3 Plug the power cord into a 120 V grounded outlet. 4 Connect the telephone line cord to the TEL. LINE jack and a wall telephone jack. Attach the Paper Tray and Document Support. TE L INL .
PAGE 11
;; ;;;; UX-P100U UX-P200U [6] Quick Reference Guide [7] Imaging Film Specifications (UX-5CR) SENDING FAXES Place your document (up to 10 pages) face down in the document feeder. 1. Structure This article is composed of polyester film coated with heat-resistant layer, matt layer ,hot melt ink layer, leader film and paper core. Ink film specification is "DNP standard ink film HC". Normal Dialing 1. Lift the handset or press SPEAKER . 2. Dial the fax number. 4. Press START/MEMORY ;;;; 1 3.
PAGE 12
UX-P100U UX-P200U MEMO 1 – 10
PAGE 13
UX-P100U UX-P200U 3. Settings CHAPTER 2. ADJUSTMENTS (1) Dial mode selector [1] Adjustments DIAL mode (Soft Switch No. SW-B4 DATA No. 3) (step 1) Select "OPTION SETTING". General KEY : Since the following adjustments and settings are provided for this model, make adjustments and/or setup as necessary. DISPLAY: FUNCTION OPTION SETTING NUMBER OF RING (step 2) Select "DIAL MODE". 1.
PAGE 14
UX-P100U UX-P200U [2] Diagnostics and Service Soft Switch 1. Operating procedure (1) Entering the Diagnostic mode Press FUNC → 9 → ROM Ver. TA01 → 8 → # → 7 , and the following display will appear. (TA02 ) After 2 sec: DIAG MODE TA01 (UX-P100U) TA02 (UX-P200U) Then press the START key. Select the desired item with the key or the # key or select with the Rapid key. Enter the mode with the START key.
PAGE 15
UX-P100U UX-P200U 3. Diagnostic items description 3. 1. Soft Switch mode 3. 6. Signal Send mode This mode is used to send various signals to the circuit during FAX communication. Every push of START key sends a signal in the following sequence. Moreover, the signal sound is also output to the speaker when the line monitor of the soft switch is on. Used to change the soft switch settings. The soft switch which is stored internally is set by using the keys. The available soft switches are SW-A1 to SW-N3.
PAGE 16
UX-P100U UX-P200U 3. 12. Entry data receive In this mode, the registered data sent from the other machine is received and the received data is registered in the machine. When this mode is used for receiving, the other machine must be in the entry data send mode. After receiving is completed, the following lists are printed. 1. Telephone list data 2. Sender register data (*) 3. Optional setting list (*) 4. Soft switch content 5. Junk fax number list (*) 6.
PAGE 17
UX-P100U UX-P200U 5. Soft switch description • Soft switch SW NO. SW l A1 DATA NO.
PAGE 18
UX-P100U UX-P200U SW NO. DATA NO. Switch setting and function ITEM 1 Digital line equalization setting (Reception) 1 2 No. 1 No. 2 Digital line equalization setting SW l A5 SW l A6 1 2 (Transmission) Initial setting 0 No. 3 No. 4 Digital cable equalizer setting (Reception No. 5 No. 6 7.2km 0km 1 1 0 0 7.2km 0km 1 1 0 0 7.
PAGE 19
UX-P100U UX-P200U SW NO. SW l B3 SW l B4 SW l B5 DATA NO.
PAGE 20
UX-P100U UX-P200U SW NO. DATA NO. 1 Switch setting and function ITEM Number of rings for auto receive 2 3 SW l D1 No. = 4 5 6 Automatic switching manual to auto receive mode Reserved Initial setting Remarks Binary input 0 OPTION 8 1 4 2 2 3 1 4 1 0 0 1 0 0 0 1 Reception after 5 rings SW l D2 SW l D3 SW l E1 SW l E2 No reception 0 0 Cl detect frequency 7 No.7 8 No.8 Distinctive ringing setting (PATTERN 4 and 5 are for CANADA only) 0 As PTT 0 0 No. 1 0 OFF 11.5Hz 0 13.
PAGE 21
UX-P100U UX-P200U SW NO. SW l E3 DATA NO. Switch setting and function ITEM 1 1 Reserved 0 2 3 Reserved Reserved 0 0 4 Reserved 0 5 Reserved 0 6 7 Reserved Reserved 0 0 8 Reserved 0 DTMF detection time SW l F1 1 No. 1 50ms 0 2 3 No. 2 0 Protection of remote reception (5 4 Remote reception with GE telephone 5 6 Remote operation code figure by external TEL (0~9) SW l G1 SW l G2 SW l G3 1 2 CNG detection in STAND-BY mode Reserved 3 Reserved 1 No Compatible No.
PAGE 22
UX-P100U UX-P200U SW NO. SW l H1 SW l H2 SW l I1 SW l I2 SW l I3 SW l I4 DATA NO.
PAGE 23
UX-P100U UX-P200U SW NO. SW l I5 SW l I6 SW l I7 SW l J1 DATA NO.
PAGE 24
UX-P100U UX-P200U SW NO. SW l K1 SW l L1 DATA NO. SW l M1 SW l M2 Initial setting 0 Reserved 0 2 Reserved 0 3 4 Reserved Reserved 0 0 5 6 Reserved Reserved 0 0 7 8 Reserved Reserved 0 0 1 Reserved 0 2 Reserved 0 3 4 5 6 Reserved Reserved Cut off mode (COPY mode) A4 paper enable Yes Enable No Disable 0 0 1 0 7 LEGAL & LETTER paper enable Enable Disable 1 8 Reserved Paper set size 1 No. 1 2 No.
PAGE 25
UX-P100U UX-P200U SW NO. DATA NO. 1 Switch setting and function ITEM 1 LCR long time (UX-P100U only) 2 SW l N2 3 4 4 5 0 Remarks Binary input 0 OPTION No.
PAGE 26
UX-P100U UX-P200U • Soft switch function description SW-A2 No. 7 Communication error treatment in RTN sending mode (Reception) SW-A1 No. 1 Protect from Echo Used to determine communication error treatment when RTN is sent by occurrence of a received image error in G3 reception. When it is set to "1", communication error is judged as no error. Used to protect from echo in reception. SW-A1 No. 2 Forced 4800BPS reception SW-A2 No.
PAGE 27
UX-P100U UX-P200U When using the Anti junk fax function, set to "1". SW-B3 No. 6, No. 7 Auto dial mode Delay timer of before line connect SW-A6 No. 1 Reserved Delay time between the dial key input and line connection under the auto dial mode. SW-A5 No. 8 Anti junk fax check Set to "0". SW-B3 No. 8 Reserved Set to "0". SW-A6 No. 2 End buzzer Setting this bit to 0 will disable the end buzzer (including the error buzzer/ on-hook buzzer). SW-B4 No. 1, No.
PAGE 28
UX-P100U UX-P200U SW-B6 No. 6 Dial tone detection (LCR center call) (UX-P100U ONLY) Used to set YES/NO of dial tone detection (calling LCR center). Phone Number Intended Purpose SW-B6 No. 7, No. 8 Reserved Ring Pattern Set to "0". SW-C1 No. 1, No. 2 Reading slice (Binary) Used to determine the set value of reading density in standard/fine mode. The standard setting is "00" (Factory setting is "00") SW-C1 No. 3, No.
PAGE 29
UX-P100U UX-P200U SW-D2 No. 4 Reserved SW-F1 No. 5 ~ No. 8 Remote operation code figure by external TEL (0 ~ 9) Set to "0". Remote operation codes can be changed from 0 through 9. If set to greater than 9, it defaults to 9. The "5 " is not changed. Ex-7 (Default: 5 ) SW-D2 No. 5 Caller ID function Used for Caller ID function. SW-D2 No. 6 Caller ID detect during CI off Detection of caller ID signal is performed as follows: 0:First CI OFF only 1:All of CI OFF SW-F2 No.
PAGE 30
UX-P100U UX-P200U SW-J2 No. 1, No. 2 Speaker volume (3 stages) SW-N1 No. 1 ~ No. 6 LCR short time (UX-P100U ONLY) Used to adjust sound volume from a speaker. First time setting transmitting to the openLCR center. SW-J2 No. 3 Reserved SW-N1 No. 7, No. 8 Reserved Set to "0". Set to "0". SW-J2 No. 4, No. 5 Handset receiver volume Used to adjust sound volume from a handset receiver volume. SW-N2 No. 1 ~ No. 6 LCR long time (UX-P100U ONLY) Second time setting transmitting to the openLCR center.
PAGE 31
UX-P100U UX-P200U [3] Troubleshooting Refer to the following actions to troubleshoot any of the problems mentioned in 1-4. [1] A communication error occurs. [2] Image distortion produced. [3] Unable to do overseas communication. [4] Communication speed slow due to FALLBACK. • Increase the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5. May be used in case [1] [2] [3]. • Decrease the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5. May be used in case [3].
PAGE 32
UX-P100U UX-P200U [4] Error code table 1. Communication error code table G3 Transmission Code Final received signal Error Condition (Receiver side) 0 Incomplete signal frame Cannot recognize bit stream after flag 1 NSF, DIS Cannot recognize DCS signal by echo etc.
PAGE 33
UX-P100U UX-P200U 3-2. Automatic document feed CHAPTER 3. MECHANISM BLOCKS 1) Use of the paper feed roller and separate plate ensures error-free transport and separation of documents. The plate spring presses the document to the paper feed roller to assure smooth feeding of the document. [1] General description 2) Document separation method: Separate plate 1.
PAGE 34
UX-P100U UX-P200U 2) Structure of recording mechanism Back of document Recording is achieved by applying a suitable pressure to the thermal head through the imaging film of the recording paper feed roller and the recording paper. The main scanning is electronically performed, and the sub-scanning is mechanically performed (by sending the recording paper with the recording paper feed roller).
PAGE 35
UX-P100U UX-P200U [2] Disassembly and assembly procedures • • This chapter mainly describes the disassembly procedures. For the assembly procedures, reverse the disassembly procedures. • • The numbers in the illustration, the parts list and the flowchart in a same section are common to each other. Easy and simple disassembly/assembly procedures of some parts and units are omitted. For disassembly and assembly of such parts and units, refer to the Parts List.
PAGE 36
UX-P100U UX-P200U 2 Parts list (Fig. 2) Operation panel unit, top cover unit and sub frame unit No. NOTE: For disassembly of the inside of the unit, refer to the exploded view in the parts guide. Q’ty No.
PAGE 37
UX-P100U UX-P200U 3 CIS unit and thermal head unit Parts list (Fig. 3) No. NOTE: For disassembly of the inside of the unit, refer to the exploded view in the parts guide. Q’ty No. 1 Mechanism unit Part name 1 4 Head cover Part name 1 2 Screw (3×10) 1 5 Thermal head unit 1 3 CIS unit 1 3 CIS unit 2 Screwdriver Hook 4 Hook Hook 5 Thermal head unit 1 Fig.
PAGE 38
UX-P100U UX-P200U 4 Wire treatment Parts list (Fig. 6) No.
PAGE 39
4–1 LINE HANDSET SPEAKER AMPLIFIER SURGE PROTECT/ FILTER CNPRG CONTROL PWB UNIT CML CI AMPLIFIER FLASH 2Mbit TEL/LIU PWB UNIT CLOCK 32.768kHz TRANSFORMER CLOCK 32.256MHz VBT DRAM 4Mbit PIO DSP IA(CX20438) CPU RTC S-RAM(32kbit) +3.
PAGE 40
4–2 CNLCD CNPN-A 16 CNPN CNCIS CNTH INTERFACE PWB CNPN-A 7 15 16 CNPN CNMT 6 SPEAKER 2 CNSP CONTROL PWB UNIT CNCSW 2 CNPW CNLIUA 6 12 MJ1 POWER SUPPLY PWB UNIT CNPS CNLIUA TEL/LIU PWB UNIT MJTEL 4 TEL LINE HANDSET AC CORD [2] Wiring diagram OPERATION PANEL PWB NUIT 14 LCD UNIT CONTACT IMAGE SENSOR THERMAL HEAD TX/RX MOTOR CAM SW UX-P100U UX-P200U
PAGE 41
UX-P100U UX-P200U [3] Point-to-point diagram CNMT TX/RX MOTOR TPBDTPADTPBD TPAD VMT VMT 1 2 3 4 5 6 THERMAL HEAD VTH VTH STRB1STRB2THI RANK THG THG THG THVDD STRB3STRB4LATCHPCLK DATA VTH 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CNPN-A KEN4A 1 KEN3A 2 KEN2A 3 KEN1A 4 DG 5 +3.
PAGE 42
UX-P100U UX-P200U 3. Operational description CHAPTER 5. CIRCUIT DESCRIPTION Operational descriptions are given below: • [1] Circuit description When a document is loaded in stand-by mode, the state of the document sensor is sensed via the 1 chip fax engine (SCE209). With depression of the START key in the off-hook state, transmission takes place. Then, the procedure is sent out from the modem and the motor is rotated to move the document down to the scan line.
PAGE 43
UX-P100U UX-P200U 4) External RAM and ROM [2] Circuit description of control PWB Moveable and programmble size external SRAM memory of up to 1 MB, DRAM memory of up to 4 MB, and ROM of up to 2 MB can be directly connected to the SCE209. By using an external address decoder, the size of SRAM and/or ROM can be extened. The ROM stores all the program object code. 1. General description Fig. 2 shows the functional blocks of the control PWB, which is composed of 3 blocks.
PAGE 44
UX-P100U UX-P200U 12) Video Processing 20) Power Up/Down Control The CX06835 supports two modes of shading correction for scanner data non-uniformity arising from uneven sensor output or uneven illumination. Corrections are provided on either an 8-pixel group or are applied separately to each pixel. Dark level correction and gamma correction are also provied. Two-dimensional Error Diffusion/Dithering is performed on halftone images.
PAGE 45
UX-P100U UX-P200U SCE209 (IC3) Terminal descriptions Pin No.
PAGE 46
UX-P100U UX-P200U SCE209 (IC3) Terminal descriptions Pin No.
PAGE 47
UX-P100U UX-P200U SCE209 (IC3) Terminal descriptions Pin No.
PAGE 48
UX-P100U UX-P200U (3) Panel control block The following controls are performed by the SCE209.
PAGE 49
UX-P100U UX-P200U (5) Modem block (CX20438) Integrated Analog Control Resisters for CX20438 The CX20438 IA can be used as a Primary Integrated Analog (PIA) codec or as a Secondary Integrated Analog (SIA) codec, depending on the signal connection with the SCE Controller ASIC device. In the SCE100 product, both the PIA and the SIA are packaged external to the SCE Controller device, whereas in the SCE209, the PIA is packaged with the SCE209 Controller and the SIA is external.
PAGE 50
UX-P100U UX-P200U [3] Circuit description of TEL/LIU PWB (1) TEL/LIU block operational description 1) Block diagram TEL/LIU PWB CONTROL PWB RTLOOP IC1-B LINE SIGTX H 0,1 0,0 1,0 1,1 SPKRP TXOUT L CML SP OUT CI DETECTOR SIGRX RXIN MICP PC1 LINEIN IC1-A MIC ENABLE Q2 IC1-D LPF TEL MUTE (H:MUTE) TX HANDASET MIC MUTE (H:MUTE) 0,20,25,30dB MODEM BLOCK (CX20438 I/A) TEL IN SIN DAC ENABLE MIC /LINE SELECT LINE IN ENABLE RX 0,6dB ADC LINE OUT ENABLE LINE SELECT 1,1 0,0 1,0 SPOUT
PAGE 51
UX-P100U UX-P200U 4) Signal selection 5. CI detection circuit • The following signals are used to control the transmission line of TEL/ FAX signal. For details, refer to the signal selector matrix table. CI is detected by the photo coupler which is integrated in series in the primary side TEL circuit well proven in the existing unit. 6.
PAGE 52
UX-P100U UX-P200U [Signals for status recognition according to input signals] Signal Name Function RHS CI NO Signal Name (CNLIUA) NO Signal Name (CNLIUA) H:The handset is in the on-hook state. 1 RHS- L: The handset is in the off-hook state.
PAGE 53
UX-P100U UX-P200U [4] Circuit description of power supply PWB 1. Block diagram 2.5A/125V AC IN Noise Filter Circuit Rectifying Smoothing Circuit +24V FUSE 4A/72V Switching Circuit +5V Control Circuit Photo Coupler Fig. 7 2-1. Noise filter circuit 2-4. Control circuit The input noise filter section is composed of L1 and C1, which reduces normal mode noise from the AC line and common mode noise to the AC line.
PAGE 54
1 2 3 CNTH-12 CNTH-14 CNTH-13 CNTH-2 CNTH-3 CNTH-10 CNTH-11 CNCIS-4 A DG LATCH- DATA PCLK STRB1- STRB2- STRB3- <ΦT> STRB4- ΦT CISCLK DG C108 DG N.M. R106 CNCIS-5 N.M. C124 R111 R124 270 270 R160 R161 4 3 2 1 270 5 6 7 8 RA3 470 270 150 R147 N.M. C125 B R105 470 4 100P 100P 100P 100P 100P 100P 100P C184 C183 C168 C187 C186 C185 C169 CNPN-16 DG X1 R174 100 R127 1M 32.256MHz C106 N.M.
PAGE 55
6–2 A B C DG D E F 7 (1-3I) DWR- 22 23 (1-3I) RAS- 6 10 11 12 13 16 17 18 19 20 9 (1-3I) CAS- C198 N.M. A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 8 G G OE WE CAS RAS NC A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 H 2 3 4 5 24 25 26 27 28 GND 15 GND 1 VCC 14 VCC 21 NC DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 IC2 MSM51V4800E DRAM H DG I C111 0.1 I +3.3V D0 D1 D2 D3 D4 D5 D6 D7 2/6 4 5 6 1 OE 32 WE 7 C128 0.1 +3.
PAGE 56
6–3 1 2 3 4 5 6 CNLIUA-10 CNLIUA-1 CNTH-5 CNLIUA-16 THCHK CNLIUA-15 A CNLIUA-4 THLOOK CNPRG-3 CNPRG-1 N.M. CNPW-7 (4-4C) FRSNS(4-4C) ORGSNS(4-5C) DR/RBN (4-6C) CSWI (5-3E) VTHON (5-5F) LEDON N.M. N.M. CNLIUA-9 CNLIUA-6 (6-1A) RCVOL (6-1E) DTMFMUTE (6-3A) SIGMUTE (6-4I) SPMUTE N.M. CNLIUA-13 CNLIUA-12 DG B N.M. MICMUTE DG N.M. R175 R172 C152 R159 N.M. 1K R163 R112 C192 R169 FLRXD C151 C181 DG C191 R153 R170 DG R171 DG DG N.M.
PAGE 57
6–4 B DG B R140 51K R102 270 R101 270 R165 270 DG DG DG DG C PWRDWN- (1-1G) C105 1000P C104 1000P C194 1000P C163 100P R148 20K FRSNSi- (3-3A) ORGSNSi- (3-3A) DR/RBN (3-3A) CSWi- (3-3A) D E CNPW-4 CNPW-3 CNPW-2 CNPW-1 CNPW-5 CNPW-6 MG MG +24V +24V DG VREG R150 DG N.M. F BAT1 CR2032 F R110 C182 0.1 R100 5.6K N.M. MG FG C167 0.1 R108 K D101 1SS355 G N.M.
PAGE 58
6–5 1 2 3 4 5 6 C VO A (5-5I) LEDON- CNCIS-1 +24V +3.3V VG B N.M. R173 VG C DG L100 0 C1 220 R1 220 (2W) R114 0 R107 10K B E R113 5.1K VG C109 0.1 CISVDD DG C110 0.
PAGE 59
6–6 1 2 3 4 5 6 (3-4A) RCVOL CNLIUA-7 (3-6A) SIGMUTE CNLIUA-8 CNLIUA-14 N.M. A RXIN TXOUT TELOUT B C B MAG E C C178 0.1 N.M. Q103 KRC102S R167 39K MAG E Q104 C159 1 MAG N.M. ZD101 B Analog signal block B MAG R156 1M R157 7.5K C176 0 C R154 3.9K N.M. C179 C MAG E B Q102 KRC102S C177 0.1 C157 0 C N.M. E D C E B MAG Q106 MAG B TELIN SIGRX C180 N.M. D102 1SS355 +3.3V SIGTX (3-3H) Q105 C175 1 R155 SIGTX C R158 D E N.M.
PAGE 60
UX-P100U UX-P200U Control PWB parts layout (Top side) 6–7
PAGE 61
UX-P100U UX-P200U Control PWB parts layout (Bottom side) 6–8
PAGE 62
A B C +24VL TP4 JP DG 2 5 ARG 1 1 SG206S 2 SG206S FILM 2 PIN Vref A CNLIUA-10 CNLIUA-12 DG TP3 4 DG FILM FILM CNLIUA-11 PIN Ci CNLIUA-1 3 PH2 4 TP2 TP1 1 DG Vref A Vref B RHS- PIN DG R6 3.3K VA2 ERZVA5D471 R5 3.3K 3 PH1 4 HOOK SW SW1 VA1 ERZVA5D471 Ring R30 1.2K(1W) +24VL PC1 TLP521-BL MJ1-4 AR1 RA-391P-V6-2 1 2 TiP 1 2 MJ1-3 C5 22/50 D C11 22/50 [2] TEL/LIU PWB circuit 4 3 4 +24VL DG ZD2 MTZJ5.6B R15 2K B M D1 1SS133 CML N.M.
PAGE 63
UX-P100U UX-P200U TEL/LIU PWB parts layout 6 – 10
PAGE 64
6 – 11 1 2 3 4 5 6 D3 ERA15-06 1 CNAC F1 2.5A/250V 3 A V1 S07K175GA L1 19mH/0.5A N.M. R1 2.2M(1/2W) C1 2.2 C25 D2 D4 ERA15-06 ERA15-06 D1 ERA15-06 N.M. C15 C28 0.01 C7 0.01 C3 1000P C2 220/200 Q3 2SC1741AS C27 4700P C26 4700P R8 47K B C C4 1000P C5 1500P C17 N.M. N.M. L2 RS908 D C6 0Ω D9 ERA22-06V3 C23 4700P D PC1 PS2501-1L R7 180 R6 *R5 2.7K *C24 270P R4 680 ZD6 JUMPER R24 120K (2W) ZD2 RD4.3SB2-T1 Q2 2SC4115S C *C24,*R5: ADJUSTMENT PARTS R10 0.
PAGE 65
UX-P100U UX-P200U Power supply PWB parts layout (Top side) Power supply PWB parts layout (Bottom side) 6 – 12
PAGE 66
6 – 13 A B C D CNPN_A-8 CNPN_A-7 CNPN_A-5 CNPN_A-6 CNPN_A-9 CNPN_A-1 CNPN_A-2 CNPN_A-3 CNPN_A-4 FRSNS ORGSNS DG +3.3V E KEN4A KEN3A KEN2A KEN1A 5 CNPN_A-16 CNPN_A-15 CNPN_A-14 CNPN_A-13 CNPN_A-12 CNPN_A-11 CNPN_A-10 SEN6 SEN5 SEN4 SEN3 SEN2 SEN1 SEN0 SW1 SW2 DG + N.M. R6 N.M. 3 6 9 # START A 2 5 8 0 UP DOWN REC/MEMO N.M. 1 4 7 STOP REDIAL PLAY N.M. 3 N.M.
PAGE 67
UX-P100U UX-P200U Operation panel PWB parts layout (Top side) Operation panel PWB parts layout (Bottom side) Note: Since the parts of PWB cannot be supplied, change it as a unit.
PAGE 68
6 – 15 A B C D CNPN-16 CNPN-15 CNPN-14 CNPN-13 CNPN-12 CNPN-11 CNPN-10 CNPN-9 CNPN-8 CNPN-7 CNPN-6 CNPN-5 CNPN-4 CNPN-3 CNPN-2 CNPN-1 FRSNS SEN4 SEN5 SEN4 SEN5 A SEN6 SEN3 SEN3 SEN6 SEN2 SEN1 SEN1 SEN2 SEN0 SEN0 E FRSNS E ORGSNS +3.3V ORGSNS +3.
PAGE 69
UX-P100U UX-P200U CHAPTER 7.
PAGE 70
UX-P100U UX-P200U [2] Power on sequence START CPU initialized MODEM initialized “WAIT A MOMENT” display STOP key ? NO “MEMORY CLEAR ?” display NO 3 sec ? YES 1 YES STAND-BY START key ? NO 2 YES COPY key ? 1 2 “MEMORY CLEARED” display “MEMORY CLEARED” display Memory clear Memory clear STAND-BY PROCESS CHECK MODE NO YES STOP key ? NO 3 sec ? NO YES STAND-BY 7–2
PAGE 71
UX-P100U UX-P200U CHAPTER 8. OTHERS [1] Service tools 1. List NO. 1 2 PARTS CODE DESCRIPTION CPWBF3201SCS1 PSHEZ3579SCZZ Extension board unit (TEL/LIU PWB) Shading wave memory standard paper Q’TY 1 1 PRICE RANK BA AD Extension board unit TEL/LIU PWB PH2 K A TP1 PIN (BROWN) PH1 TP3 DG (ORANGE) C E C E R30 K A TP2 FILM (RED) TP4 +24VL (YELLOW) NO.
PAGE 72
UX-P100U UX-P200U 2. Description 2-1. Relay board unit 1. Remove the TEL/LIU PWB, control PWB and Power Supply PWB from this unit, and mount the relay board unit instead. • Before connecting the wiring to the relay board unit, set the test PWB switches to the fixed position. 2. The setting is as follows. • The relay cables are used as one pair. • The hook switch is manually operated. Relay cable 1 CNLIUA CNLIUA 12 The hook switch is operated by the mechanical unit switch and the test PWB switch.
PAGE 73
UX-P100U UX-P200U 3. Shading paper The white and black basis is applied to remember the shading waveform. Be sure to perform this operation when replacing the battery or replacing the control PWB. Execute in the shading mode of DIAG mode.
PAGE 74
UX-P100U UX-P200U [2] IC signal name CONTROL PWB UNIT IC1: RH-iX2890AFZZ (SST39VF020P) A11 1 32 OE# A9 2 31 A10 A8 3 30 CE# A13 4 29 DQ7 A14 5 28 DQ6 A17 6 27 DQ5 WE# 7 26 DQ4 VDD 8 25 DQ3 NC 9 24 VSS A16 10 23 DQ2 A15 11 22 DQ1 A12 12 21 DQ0 A7 13 20 A0 A6 14 19 A1 A5 15 18 A2 A4 16 17 A3 SST39SF/VF020P Standard Pinout Top View Die Up 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
PAGE 75
UX-P100U UX-P200U [3] Changing the record paper size How to change the A4 size and letter size of the record papers 1) It becomes the record paper of the A4 size by installing A4 guide (PGiDM2629XHZZ) which shows in the drawing. Remove A4 guide when you use the record paper of the letter size. Paper tray ass'y Hook A4 Guide PGiDM2629XHZZ 2) Set soft switch SW-L2 No.1 and the initialization of SW-L2 No.2 as follows. SW NO. DATA NO.
PAGE 76
UX-P100U UX-P200U MEMO 8–6
PAGE 77
UX-P100U UX-P200U PARTS GUIDE UX-P100 MODEL UX-P200 SELECTION CODE UX-P100U (Open LCR) UX-P200U DESTINATION U.S.A. U.S.A. CONTENTS 1 Cabinet, etc.
PAGE 78
UX-P100U UX-P200U [1] Cabinet,etc.
PAGE 79
UX-P100U UX-P200U NO. PARTS CODE PRICE RANK NEW MARK PART RANK AL AD AQ BR BR BB AF AL AA AC AC AL AB AB AC AD AD AR AD AD AG BR AZ AD AD AB AB AB AE AD AD AM BP AF AD AF AD AD AD AB AB AD AB AD AD AD AP AL BH AH AH AN AD AD AA AA AB AA N N N N N N N N C C C E E E E C C C C C C C C C C C C C C B D C C C C C C C C C B D C C C C C C C C C C C C B C E D D C C C C C C C DESCRIPTION [1] Cabinet,etc.
PAGE 80
UX-P100U UX-P200U [2] Top cover/Sub frame 27 25 16 28 26 15 B1 12 B2 30 6 11 1 B1 20 B2 19 23 13 B2 4 24 3 2 B3 24 22 29 9 PARTS CODE PRICE RANK NEW MARK PART RANK AG AB AD AF AF AQ AT AD AB AB AC AC AL AL AG AG AF AL AD AD AH AH AB AB AC AC AD AQ AA AD AD AD AA AC N N C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C D C C C DESCRIPTION [2] Top cover/Sub frame 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 B1 B2 B3 GCOVA2448XHS
PAGE 81
UX-P100U UX-P200U [3] Upper cabinet/Document guide upper 901 10 1 9 6 5 13 7 12 15 3 4 B1 8 17 11 14 2 16 PARTS CODE NO.
PAGE 82
UX-P100U UX-P200U [4] Drive unit 1 15 16 4 18 11 8 15 21 14 B1 7 22 20 3 6 9 10 2 12 19 13 5 PARTS CODE NO.
PAGE 83
UX-P100U UX-P200U [5] Packing material & Accessories 14 12 2 4 6 21 TAPE TAPE 16 15 3 TAPE 7 9 18 8 10 11 AC CORD R 17 5 1 (3) (1) (4) (2) 20 R NO.
PAGE 84
UX-P100U UX-P200U NO.
PAGE 85
UX-P100U UX-P200U NO.
PAGE 86
UX-P100U UX-P200U NO.
PAGE 87
UX-P100U UX-P200U NO.
PAGE 88
UX-P100U UX-P200U NO. PARTS CODE PRICE RANK NEW MARK PART RANK AC AC BF AD AD AD AD AC AD AG N N N N N N C C B B B B B B B B Metal film resistor(2W 120KΩ ±5%) Resistor(1/4W 2.2KΩ ±5%) Transformer(PTTN126-KTT) Varistor(S07K175GA) Variable resistor(2.2KΩ) Zener diode(RD27SB-T1) Zener diode(RD4.3SB2-T1) Zener diode(RD30FB3-T7) Zener diode(RD6.2SB-T1) Zener diode(RD5.
PAGE 89
UX-P100U UX-P200U Index PARTS CODE [C] CCNWN484AXH01 CGERH2314XH04 CGERH2566XH01 CLEVP2358XH01 CLEVP2359XH01 CLEVP2360XH01 CLEVP2361XH01 CLEVP2362XH01 CPAKC475CXH01 CPLTP3183XHR1 CROLR2481XH01 [D] DCEKC182RXHZA ″ DCEKC182RXHZZ ″ DCEKL335CXH01 ″ DCEKP334CXH01 DCEKP334CXH02 DCEKP336CXH01 ″ DCEKP336CXH02 ″ DCEKP337CXH01 ″ DUNTK468BXHFW [G] GCABB2393XHSA GCASP2145XHSA GCOVA2447XHSA GCOVA2448XHSA GLEGG2078XHZZ [H] HPNLH2418XHSA HPNLH2418XHSB [J] JBTN-2339XHSA JBTN-2340XHSA JBTN-2340XHSB JBTN-2341XHSA [L] LBNDJ2
PAGE 90
UX-P100U UX-P200U PARTS CODE No.
PAGE 91
UX-P100U UX-P200U PARTS CODE 0CBUEXCAP272/ 0CBUEXCAP332/ 0CBUEXCAP334/ 0CBUEXCAP470/ 0CBUEXCAP472/ 0CBUEXCAP473/ 0CBUEXEAG222/ 0CBUEXJAH332/ 0CBUEXJAH474/ ″ 0CBUEZ0747ZZ/ 0CBUFBA222EQ/ 0CBUGA0290ZZ/ 0CBUGA0291ZZ/ 0CBUGA0292ZZ/ 0CBUGCM103BH/ ″ 0CBUGCS152AC/ 0CBUGCU102JC/ 0CBUGCU472BW/ 0CBUGCZ472HF/ ″ 0CBUGFM224KR/ 0CBUGXGCF102/ 0CBUGXGCF152/ 0CBUGXGDF271/ 0CBUGXGFD104/ 0CBUKZ0790ZZ/ 0CBUZZ0203ZZ/ 0CB829655049/ No.
PAGE 92
UX-P100U UX-P200U COPYRIGHT © 2001 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. SHARP CORPORATION Communication Systems Group Quality & Reliability Control Center Higashihiroshima, Hiroshima 739-0192, Japan Printed in U.S.A.