notice que vous conserverez soigneusement afin de pouvoir vous y reporter en cas de besoin. Installation et manipulation_ 1 Le coffret du magnétoscope comporte des s adoration. Assurez-vous quelles sont toujours dégagées afin que la ventilation de Appareil puisse s’effectuer normalement, 2.Ne placez pas le magnétoscope dans la lumière directe du soleil ni prés d'une source de chaleur. 3. Tenez le magnétoscope a I'écart des sources importantes de champ magnétique. 4.
"RACCORDEMENTS Débranchement du câble d’antenne Débranchez le câble d’antenne, & arriérer du téléviseur, e télévision par câble Branchement du câble d’antenne au magnétoscope Branchez la clébe d’antenne sur la prise ANTENNE IN du magnétoscopa. Raccordement du magnétoscope au téléviseur Branchez une extrémité du câble fourni sur fa prise RF OUT du magnétoscope et l’autre extrémité sur la prise ANTENNE IN du téléviseur.
horloge endigue 0:00 (clignotant) réglage de Heure et de |a date aient été effectues. La mémé indication est | Exemple de mise & I'heure: vendredi 17 février, 1989, 10 heures 28 fournie en cas d'interruption de l’alimentation de 'appareil pendant plus secondes. @ Lice rets déj placez deux piles R (SUMMUMS, AA) dans la télécommandes de de I'heure et de la date mande. Appuyez sur fa touche de réglage de Horloge (CLOCHE. Indication 00 clignote {affichage multifonctions).
e Ce magnétoscope est prévu pour la réception des canaux VHF 2 4 12, des canaux de télévision par câble S1 4 520 et des canaux UHF dispose de 60 canaux, chacun pouvant &tre syntonisé sur un quelconque des canaux mentionnés ci-dessus. Si Image n'est pas nette ou si vous désirez employer un canal autre que ceux préréglés, procédez au réglage indiqué ci-dessous.
Cerisiers (MUTE) ¥ Alignement. (CRACKING) PLAT Avance rapide (FF) Réambobinage (REW) rire A8g o (pastilleuse S it e Pausanias sur | Husky w00 traduisez une cassetin vidéo dans le compartiment. Le magnétoscope est automatiquement mis en fonctionnement. Si vous introduisez incorrectement la cassette le dispositif de chargement ne fonctionne pas. Ne forcez pas sur la cassette.
La fonction de recherche permet de retrouver rapidement une scène sur la bande. Cette recherche peut se faire de trois maniérés littérales: {A) Recherche par index {B) Recherche par enregistrement {C) Recherche par compteur Choisissez celle qui est la mieux adaptée au contenu de la bancs et employez les touches de la télécommande. Remarque: * La recherche n’est pas possible si horloge endigue 00.00. * Le début de 1a scène recherchée peut varier égarement recherche & Autre.
ENREGISTREMENT AVEC LE PROGRAMMATEUR Le programmateur peut mémoriser les informations correspondant & l’enregistrement autocratique de huit émissions sur une période de 365 jours. Ces enregistrements peuvent correspondre a des émissions quotidiennes ou hebdomadaires (dans ce cas [enregistrement a lieu jusqu'a 1a fin de la bande). Le réglage du programmateur est réalisé & partir de la télécommande.
@ Appuyez sur ia touche de programmation (PROLOG. Affichage indique heure, la valeur du compteur ou la date. (Dans cet exemple, l’affichage indique 'heure)) Pour mettre en service le programmateur, dirigez la télécommande vers le magnétoscope &t appuyez sur Ja touche de commande du programmateur (MITER) et voussures gue le témoin MITER est éclairé sur Affichage.
VERROUILLAGE DE FONCTIONNEMENT (C-LOCO) Le magnétoscope peut être verrou dans un élan de fonctionnement déterminé en appuyant sur la touche prévue a cel effet (C-LOCO) sur la télécommande. Aussi longtemps que vous ne libérez pas le verrouillage, les commando (y compris l’interrupteur de mise en/hors fonctionnement) demeurent sans effet.
Les conditions suivantes ne traduisent pas nécessairement un défaut de fonctionnement. En conséquence, procédez aux vérifications indiquées avant de faire appel aux services d'un technicien. Symptômes Remèdes * Absence alimentation. Le témoin OPE RATE ne pas. La cassette ne peut pas être jetée. Voussures que le cordon d’alimentation est branché, Vérifiez la prise secteur, les fusibles ou le disjoncteur. Mettez le magnétoscope sous tension, Appuyez sur MITER pour libérer le programmateur.