TABLE DES MATIÈRES PARTICULARITÉS « Haute Qualité (HQ) .
VUE D’ENSEMBLE Avant Interrupteur de mise entorse f " (OPE RATE) : L'heure est endiguée quel que | cet interrupteur : d’éjection (ABJECT) N LEC URE/ENREGISTREMENT) Affichage multifonction (Les explications sont donnes avec celles relatives au fonctionnement) fonctionnement soit 'état de Capteur de télécommande A W.
RÉGLAGE DE HEURE ET DE LA DATE Ce magnétoscope est pourvu d’une horloge 24 heures. Après l’introduction [Exemple de réglage de Horloge: 17 février 1991, 10 heures fiche du cordon ¢'alimentation dans une prise secteur, Horloge indique [Affichage du magnétoscope] 0:00 (clignotant} et ce. jusqu'a ce que le réglage de I'heure et de la date ait touche de régla été effectue. La mémé indication est fournie en cas d'interruption de n:%m :m mmm l’alimentation de F'appareil pendant plus de 20 secondes.
RÉGLAGE DES CANAUX Pour ignorer un canal Si un (ou plusieurs) canal n'a pas é1é préréglé, il peut être ignoré en [ procédant de la maniéré endiguée ci-dessous. Exemple: ignorer le canal 39 @ Choisissez le canal vidéo sur le téléviseur. Metiez le magnétoscope en fonctionnement au moyen de l’interrupteur (PERBORATE.
Recherche vidéo Tite ci-dessous pour retrouver rapidement la scène Suivez la procédure d qui vous intéresse. @ Alors que le magnétoscope procédé & |a lecture de la bande, appuyez sur Ja touche d'avance rapide (FF) pour effectuer une recherche vers l'aval et ,mc« la touche de rembobinage (REW) pour effectuer une recherche vers "amont. @ Appuyez sur la ouche de lecture (PLAT) pour reprendre la lecture normale. REMARQUES: + Le son est coupé pendant une recherche, « Indication affichée PLAT) n'est pas modifiée.
repositionner DE LA LECTURE Grèce & cette fonction, il est possible de répéter la lecture d'un enregistrement ou d'une scène. @ Tandis que le magnétoscope %Somma 2 la lecture d'une bande, appuyez sur la touche de répétition (REPENT) au début de la scène dont vous désirez répéter la lecture. Le pictogramme “” clignote. LR pictogramme 62" demeure écl Appuyez une nouvelle fois sur cette touche a la fin de la scène.
ENREGISTREMENT AVEC reprogrammable | | Le programmateur peut mémoriser les informations correspondant & enregistrement Complémentairement d'une émission diffusée sur le canal 7, le 7 mars automatique de juil émissions sur une pariade de 365 jours. Ces enregistrements 1991 entre 9 heures et 10 heures 30. || est actuellement 10 heures peuvent correspondre & des $missions quotidiennes ou hebdomadaires {dans ce cas 28 16 17 février 1091 . ’ memento a lieu jusqu la fin de la bande).
Enregistrement commandé par signaux VPS Les signaux VPS (Vidéo Programme Myste) émis par la station de télévision agissent sur le programmateur de maniéré a enregistrer une émission dans sa totalité mémé st pour diverses raisons la grille des programmes a été modifiée.
COMPTEUR DE BANDE i comporte ding chiffres et affiche en heures, minuscule et secondes la durée du défilement. Le changement des indications fournies par le compteur, sa e & zéro et l’appel a sa fonction de mémoire sont obtenus & paroir de la. télécommande. Affichage du compteur ® Mettez le magnétoscope en fonctionnement au moyen de Interrupteur (PERBORATE. {Indication du mode de fonctionnement s affiche.) @ Appuyez sur la touche d’affichage (DISPERSAL. (La valeur du compteur g'affiche.
Vous pouvez régie le magnétoscope & distance au moyen de la télécommande. Pour cela, dirigez Réémetteur de télécommande vers le capteur placé sur le magnétoscope et procédez aux réglages comme vous le feriez & partir des commandes qui se trouvent sur le magnétoscope. Mise en place des piles {.a télécommande est alimentée par deux ¢ piles de 1,5 Volt R6 AA).
AVANT DE FAIRE APPEL A UN TECHNICIEN Les conditions suivantes ne traduisent pas nécessairement un défaut de fonctionnement. £n conséquence, procédez aux vérifications endiguées avant de faire appel aux services d'un technicien. Symptômes Remèdes Symptômes Remèdes « Absence d’alimentation Le témoin OPE RATE ne s'éclaire pas La cassette ne peut pas être claie. Assurez-vous gue le cordon d'alimentation est branché. Vérifiez la prise secteur, les fusibles ou lg magnétoscope sous tension.