XL-60H/70H SERVICE MANUAL No. S4031XL60H/// XL-60H XL-70H Illustration: XL-60H XL-60H/XL-70H Micro Component System consisting of XL-60H/ XL-70H (main unit) and CP-XL60H/CP-XL70H (speaker system). • In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified should be used. • Note for users in U.K. Recording and playback of any material may require consent, which SHARP is unable to give.
XL-60H/70H SAFETY PRECAUTION FOR SERVICE MANUAL Precaution to be taken when replacing and servicing the Laser Pickup. The AEL (Accessible Emission Level) of Laser Power Output for this model is specified to be lower than Class I Requirements.
XL-60H/70H FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL. SPECIFICATIONS XL-60H/70H ● Cassette deck section ● General Power source: Power consumption: Dimensions: Weight: Frequency response: AC 230 V, 50 Hz 50 - 14,000 Hz (Normal tape) 50 W Signal/noise ratio: 50 dB Width; 160 mm (6-5/16") Height; 241 mm (9-1/2") Depth; 298 mm (11-3/4") Wow and flutter: (For Europe) Wow and flutter: (For U.K.) 3.6 kg (7.9 lbs.) 0.3 % (DIN 45 511) 0.
XL-60H/70H NAMES OF PARTS XL-60H/70H 1 2 3 ■ Front panel 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26.
XL-60H/70H ■ Speaker section CP-XL60H 1. 2. 3. 4. Tweeter Woofer Bass Reflex Duct Speaker Wire 1 2 3 4 CP-XL70H 1. 2. 3. 4. 1 Tweeter Woofer Bass Reflex Duct Speaker Wire 2 3 4 XL-60H/70H ■ Remote control 1 1. Remote Control Transmitter LED ● Tuner control section 2. Programme Type/Traffic Information Search Button 3. Preset Up/Down Buttons 2 4 5 6 ● CD control section 4. Clear Button 5. Random/Repeat Button 6. Memory Button 7. Stop Button 8. Play/Pause Button 9.
15 15 Notes concerning use: ● Replace the batteries if the operating distance is reduced or if the operation becomes erratic. ● Periodically clean the transmitter LED on the remote control and the sensor on the main unit with a soft cloth. ● Exposing the sensor on the main unit to strong light may interfere with operation. Change the lighting or the direction of the unit. ● Keep the remote control away from moisture, excessive heat, shock, and vibrations.
XL-60H/70H 1 5 Check the supplied accessories Listening to a CD 3 OPEN/CLOSE 4 Label side up AM loop aerial ×1 Remote control × 1 5 1 (For U.K.) AC power lead × 1 FM aerial × 1 2 2 Insert the batteries. cover. 7 2 6 Putting batteries into the remote control 1 Remove the battery 6 (For Europe) 1 Press the ON/STAND-BY button to turn the power on. 2 Press the FUNCTION button until “CD” or “NO DISC” appears. 3 Press the OPEN/CLOSE button to open the CD compartment.
XL-60H/70H DISASSEMBLY XL-60H/70H Caution on Disassembly Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance: 1. Take cassette tape and compact disc out of the unit. 2. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit. 3. Take off nylon bands or wire holders where they need to be removed when disassembling the unit.
XL-60H/70H CP-XL60H Front Panel STEP 1 PROCEDURE FIGURE 1. Net Frame ........... (A1) x1 2. Front panel .......... (A2) x1 3. Screw .................. (A3) x4 9-4 REMOVAL Speaker Tape Mechanism Open Speaker Box Tweeter Cassette Holder (K1)x4 ø2.5x10mm (A2)x1 (A1)x1 Figure 9-1 (L1)x3 ø2.5x14mm CD PWB (M2)x1 ø2.5x10mm Digital Out PWB PWB Washer (A3)x4 ø4x20mm Woofer (L2)x2 (L1)x2 (M1)x1 ø2.5x8mm (L2)x1 Figure 9-4 (L1)x1 ø2.
XL-60H/70H REMOVING AND REINSTALLING THE MAIN PARTS TAPE MECHANISM SECTION (A2)x1 ø2x7mm Perform steps 1 to 8 and 10 of the disassembly method to remove the tape mechanism. (See page 8.) (A2)x1 ø2x3mm (A1)x2 ø2x8mm How to remove the record / playback and erase heads (See Fig. 10-1.) 1. Remove the screws (A1) x 2 pcs., to remove the erase head. 2. Remove the screws (A2) x 2 pcs., to remove the record/ playback head.
XL-60H/70H How to remove the tape mechanism PWB (See Fig. 11-1.) (F1)x1 Tape ø2x3mm Mechanism PWB 1. Remove the screws (F1) x 1 pc., to remove the tape mechanism PWB. 2. Remove the screws (F2) x 1 pc. 3. Remove the solder joints (F3) x 2 pcs., to remove the tape mechanism PWB. (F2)x1 ø2x8mm Tape Mechanism PWB (F3)x2 Solder Joint Figure 11-1 How to remove the jog motor (See Figs. 11-2.) Jog Motor 1. Remove the side panel and top cabinet. 2. Remove the jog belt (G1) x 1 pc., from the motor pulley. 3.
XL-60H/70H ADJUSTMENT MECHANISM SECTION TUNER SECTION • Driving Force Check fL: Low-range frequency fH: High-range frequency • AM IF/RF Signal generator: 400 Hz, 30%, AM modulated Torque Meter Specified Value Play: TW-2412 Over 80 g Torque Meter Specified Value Play: TW-2111 30 to 60 g. cm Fast forward: TW-2231 55 to 140 g.cm Rewind: TW-2231 55 to 140 g.cm • Tape Speed Adjusting Point Test Tape MTT-111 Display Frequency Frequency • Torque Check Variable resistor in motor.
XL-60H/70H RDS CIN Subcarrier input (comparator input). 7 TEST Test input. 8 XOUT Crystal oscillator output (4.332MHz). XIN Crystal oscillator input (external reference signal input). 10 Vssd Digital ground. 11* Vddd Digital power supply (+5V). 12 MODE Read mode setting (0 : master, 1: slave). 13 RST RDS-ID/RAM reset (positive polarity). 14 RDDA RDS data output. 15* RDCL RDS clock output (master mode)/ RDS clock input (slave mode).
XL-60H/70H TEST MODE The test mode applied to this microcomputer has three modes, namely ordinary test mode to be used for adjustment or measurement, aging test mode to be used for aging test, and self-diagnosis test mode for self-inspection in case of final product inspection. The test mode specification prescribes the microcomputer with RDS (RH-IX0026SJZZ) . There are two types of indication examples; large ones for the microcomputer with RDS, and smaller ones for the microcomputer without RDS. 1.
XL-60H/70H 2. Step 2 Mode When the "PLAY" button is pressed in this mode, the laser lighting command LDON (8400) is sent, and the laser is turned on. Other operations are not performed. If the following buttons are pressed in this state, the operation is performed as follows. "POWER" ................ The test mode is turned off, the power is turned off, and the ordinary standby mode is set. "FF/FWD" ................ The pickup slides toward the outer periphery while this button is held down. "REW/REV" ....
XL-60H/70H 5. Step 5 Mode The CD initialization operation flow is executed to the end, the mute is set to off, and playback is started. Even when the playback reaches the outermost periphery of disc, the operation does not stop. The LCD display indicates the playback past time as in case of ordinary CD playback. When the following operation buttons are pressed in this sate, the operation is executed as follows. "POWER" .................
XL-60H/70H 3. Preset frequencies for various destinations (random preset memory) CH 1 2 3 4 5 BAND FM STEREO Europe 2, 4 CH 6 7 8 9 10 11-15 FM 87.50 MHz FM108.00 MHz FM 98.00 MHz FM 90.00 MHz FM106.00 MHz BAND AM Europe 2, 4 AM 522 kHz AM1620 kHz AM 990 kHz AM 603 kHz AM1404 kHz LW CH 16-25 26 27 28 29 30 BAND FM MONO Europe 2, 4 FM106.00 MHz FM 90.00 MHz FM 98.00 MHz FM108.00 MHz FM 87.50 MHz • The hatched sections of the table are not stored in memory. 4.
XL-60H/70H * When the "PRESET UP" button or "PRESET DOWN" button is pressed after completion, the following indication appears. CH indication (for 2 seconds) Frequency indication (for 2 seconds) Time series indication of PS name indication is enabled. (The same as in case of Ordinary) NO PS (Blinking for 5 seconds: 1 Hz) Note: If PS is fixed after the frequency indication is resumed, the PS name indication is restored. * If signal exists at 106.50 MHz, the following indication appears. FM 106.
XL-60H/70H g) When 01 to 03CH were all used, scan is aborted at the frequency at which filling occurred, and the following indication appears. Number of stored stations -> Indication of stored channel -> Indication of frequency -> Return to initial FM 106.50 MHz (ST) (1 second) (1 second) (1 second) In this period up to 3 stations are continuously indicated (1 to 3 CH). h) If even one station could not be preset and stored in the APMS mode, "_0MEMORY" is indicated after scanning, and then FM 106.
XL-60H/70H 7. Key input diagnosis Test Mode (TEST 6) When the test mode is set, the following indication appears. This test mode is intended to check whether all the main unit buttons can be detected. Accordingly, in this test mode checking as to whether the "POWER" button was pressed after all the buttons shown below were pressed is performed. If the result is OK, OK is indicated. Even any one of keys was not pressed, an error is indicated.
XL-60H/70H NOTES ON SCHEMATIC DIAGRAM • Resistor: To differentiate the units of resistors, such symbol as K and M are used: the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with “Fusible” is a fuse type. • Capacitor: To indicate the unit of capacitor, a symbol P is used: this symbol P means micro-micro-farad and the unit of the capacitor without such a symbol is microfarad.
XL-60H/70H CNP301 FM MUTE LEVEL VR351 10K(B) AM ANT VD301-1 SVC348S SWITCHING R_MUTE Q351 AM OSC OUT 3 4 5 17 FM/AM OUT VSM AM LOW CUT 18 6 FM DET STEREO SD GND IC303 FM IF DET./FM MPX./AM IF LA1832 9 8 AM MIX OUT AM IF IN 7 16 14 13 15 MO/ST 2 19 MPX VCO 1 AM OSC.
XL-60H/70H E IC201 KIA4558P SURROUND CONTROL R-CH IN R-CH OUT A_12V 6 5 7 8 Q201 IC201 KIA4558P 16 15 14 13 11 12 10 9 IC521 RDS CIRUIT LC72723M AMP.
XL-60H/70H 1 ~ 4 39 ~ 42 X701 8MHz X702 32.
XL-60H/70H LCD701 LCD DISPLAY 1 ~ 4 5 ~ 38 39 ~ 42 CL ID_DW CLID_UP CLID_PRO 02 768kHz SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG9 SEG11 SEG8 SEG27 73 COM0 SEG28 72 VLC3 SEG29 71 VLC2 SEG30 70 VLC1 SEG31 69 VDD SEG32 68 OSC2 SEG33 67 OSC1 CCE 66 XO 14 MMOD VREF 18 KEY2 PU_IN 58 CLID_DW CLID_UP 57 56 MVOL_DW 55 19 MODEL 20 CLID_PRO BUS0 PU_IN 8 7 TO CD PWB 6 5 4 3 2 1 CNS702 TAPE_SW A_12V 1 2 3 4 6 5 8 7 D_GND U
XL-60H/70H AM TRACKING fL R363 6.8K R364 6.8K C373 0.015 PHASE MO/ST (AM/FM) (2.2V) 4V 1.3V 1.3V L-CH OUT R355 3.8V 3.3K (1.2V) 3.8V (1.9V) R366 2.2K 12 C358 1/50 C357 2.2/50 C355 22P R376 10K C370 1/50 C356 0.001 FM IF 13 PHASE R-C OUT MPX IN MPX VCO VCC 5V 0V 10 11 AM IF ZD351 MTZJ5.1B +B +B 2 C374 0.015 R357 470K R356 1K C368 1/50 2.1V 2.3V (0V) C354 0.022 CF351 CF352 2 T351 AM IF 9 3 C372 1/50 15 14 16 C398 100/10 FM DET 0V 3 1 R353 2.9V C399 270 (4.3V) 0.
XL-60H/70H R202 8.2K R529 1K 10V (0V) C525 22P(CH) C524 560P G D201 1N4148 2 S R208 330 8 5.0V R209 10K IC201 KIA4558P 5.0V 4 3 R205 10K (4.4V) 0V ( )SURROUND OFF R210 10K 5.0V 2 5.0V R211 2.7K 1 R215 12K C215 1/50 R217 12K C211 0.0056 C209 47/16 R213 12K R203 100K C213 4.7/50 L IN R201 8.2K C203 1/50 AUX R RDS DATA VSM 0V 2 VSS CE VDD 9.6V DI TEST NC 1 VREF 4.8V 3 CL 5V 4 5 0V 0V C426 0V 10/16 C424 0.1(ML) 4.8V 4.8V 6 ROUT LOUT 4.8V RBS1 LBS1 4.
SW728 VOLUME/JOG SW714 DISPLAY MODE R717 2.2K SW723 BAND R709 1.5K SW713 VOLUME SELECT R718 1.5K SW722 BASS/TREBLE R710 1.2K SW712 PLAY/CD PAUSE R719 1.2K R711 1.2K SW711 TUNING UP 100 2 Q708 KTA1266 GR SWITCHING +B SW721 MEMORY/SET D730 HY2043 D736 HY2043 SWITCHING Q709 KRC102 M D732 HY2043 3 R7B3 2.2K R796 180 D737 HY2043 R795 180 1 SW710 CLOCK/TIMER/SLEEP R797 180 C SW709 ON/STAND-BY SW700 JOG CNP706 CNS706 1 2 3 C A B R728 1K C703 0.
XL-60H/70H LCD701 LCD DISPLAY 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 74 2.5V SEG27 73 2.5V SEG28 72 2.5V SEG29 71 2.5V SEG30 70 2.5V SEG31 69 2.5V SEG32 68 2.5V SEG33 67 5V CCE 66 4V BUCK IC701 IX0026SJ SYSTEM CONTROL MICROCOMPUTER 64 4.3V BUS2 63 4.3V BUS0 61 60 5V CD_RES 59 PU_IN 58 CLID_DW 57 CLID_UP 56 55 0V MVOL_UP 54 STEREO 0V SD 0V DATA 5V BACK_LIGHT NC P_CONT 5V CD+B 5V P_MUTE 0V 4.
XL-60H/70H A IC805 TA7291S NC CD SIGNAL 1 CD LID PWB-A9 2 3 4 5 6 7 9 8 R872 2.2(1/2W) B FROM DISPLAY PWB CNS702 P29 12-C PU_IN 1 2 3 4 5 6 7 8 9 10 11 12 13 1 3 3 R873 5.6K CNP702 CFW806 1 C871 47/16 SW802 CD LID CD_STB BUS0 R874 2.2K BUS1 BUS2 BUS3 BUCK CCE R876 150K R877 68K CLID_SW CLID_PRO R880 47K CLID_UP CLID_DW CD_RES C R813 10 D L803 10µH +B C825 0.056 R817 1K R818 1K R814 3.3K C824 0.056 C826 C827 15P 15P (CH) (CH) R812 3.3K C823 0.01 C819 0.1 C821 0.
XL-60H/70H CNP804 1 1 6 CNS804 9 8 CD PWB-A3 IC805 TA7291S MOTOR DRIVER 1 2 2 M M801 CD LID MOTOR C872 0.1 74 K CFW807 1 1 2 2 SW730 CD LID OPEN/CLOSE C861 0.001 CD_L A_GND CD_R L804 2.2µH M_GND M_12V D_GND Q861 2SB562 C 5V 6.3V CD_6.2V C844 0.0068 SP+ 6 5 4 3 2 1 SP- 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 SP+ SL- R863 2.2K +B PU-IN GND 6 5 4 3 2 1 CNP803 C859 470/10 BI803 C860 0.1 6.3V 2.1V 2.1V 3.1V 2.5V 0V 0V 0V 2.8V 2.2V 2 3 2.8V NC 2.
XL-60H/70H FROM POWER PWB A ANTENNA TERMINALS SO601 SPEAKER TERMINALS R-CH GND FROM POWER SO401 AMP.
XL-60H/70H DISPLAY PWB-A2 TO MAIN PWB P32 6-G R746 R743 R775 R741 R740 R739 1 2 3 4 5 6 7 8 9 10 11 12 CNS703 CLOCK/TIMER/ SW722 SLEEP BASS/ TREBLE SW710 SW718 SURROUND X701 R725 R724 R733 R710 R782 SW721 C701 R728 L701 R732 R731 C703 R722 C702 R723 MEMORY 1 R727 R721 /SET 2 R783 3 R729 95 55 60 1 100 90 65 85 70 80 R761 R774 R762 R763 R764 R765 R766 R767 R768 R769 R770 R771 R772 R773 R785 BI702 1 2 3 4 5 6 7 8 9 R787 R708 R798 SW726 TUNING DOWN SW725 STOP/ CLEAR SW716 EON CNS704 P32 6-F SW7
XL-60H/70H CD LID PWB-A9 CNP803 SW802 CD LID NSW801 PICK UP IN NM802 SPINDLE MOTOR F3895AF 1 B BK GY GY GY GY GY GY RD WH GY WH GY WH C821 BCE R804 C802 C829 C838 R802 C804 R801 C803 C801 C813 13 12 15 10 C848 R828 C846 20 5 R826 C847 24 R829 1 BI801 RD WH GY WH GY WH GY WH R821 R824 C844 C845 R825 IC801 R827 1 R822 C842 R808 C809 C807 C812 R807 30 31 R862 R861 IC804 R863 C859 C841 C818 55 10 IC802 15 45 20 40 25 35 15 11 1 CNS801 C860 E C B L801 R80B R80G Q801 R80E
XL-60H/70H TO MAIN PWB FROM DISPLAY PWB CNP652 P32 1-A CNS707 2 1 CNS651 P33 12-F BR 1 2 CNS652 RD RD BR 2 1 Q683 E C B R651 C656 D658 D659 C659 C658 C657 D651 C651 D652 D654 C654 C695 R686 BI651 D653 R685 D657 BI652 F651 T3.15A L 250V 1 2 3 CNP707 2 D656 POWER PWB-B1 1 T651 MAIN POWER TRANSFORMER F652 T1.
XL-60H/70H WAVEFORMS OF CD CIRCUIT NO DISC FOCUS SEARCH 1 STOP 12 1 FOO FO+ 13 2 IC804 26pin 3 FO- 14 3 SEL 5 6 1 11 2 TEI 15 3 6 SBAD 11 2 3 TEI 1 TRO 2 IC802 49pin RFO 15 3 FMO 3 IC802 53pin IC801 22pin STOP PLAY REVIEW 6 1 FEI TEI 1 TRO 2 IC802 46pin IC802 43pin RFGO 11 2 IC801 19pin IC802 49pin RFRP 15 3 IC801 17pin 3 FMO IC802 53pin STOP TEI PLAY TCD-782 TNO-02 PLAYBACK 16 1 IC802 46pin TRO SBAD LO 1 RO 2 IC802 85pin 2 IC802
XL-60H/70H TROUBLESHOOTING When the CD does not function When the CD section does not operate when the objective lens of the optical pickup is dirty, this section may not operate. Clean the objective lens, and check the playback operation. When this section does not operate even after the above step is taken, check the following items. Remove the cabinet and follow the troubleshooting instructions.
XL-60H/70H Make sure that the disc is normal, and set the CD TEST MODE (STEP 1). Is the measured voltage as specified in circuit diagram? Check the main unit power supply circuit. No Yes Is "Er-CD01" displayed"? No Yes Move the pickup to most internal circumference side of disc. Turn the power off and reset the CD TEST MODE (STEP 1). Is "PU ERROR " not displayed? No Check the pattern between pin 57 (PUIN) of IC701 and BI803/ CNS803. Check the between BI803/CNS803 and PU-IN switch.
XL-60H/70H • Laser failure. Is +6.2V applied to the emiter of Q861 ? No Check the PWB pattern between pin 16 of CNS602 and emiter of Q861. Yes Check the peripheral parts of IC804 and Q861. Is +5V applied to the collector of Q861 ? No Yes No Check the PWB pattern between collector of Q861 and pin 62 of IC802. No Check the PWB pattern between collector of Q861 and pin 1 of IC801.
XL-60H/70H • Focus servo sawtooth wave failure. Is sawtooh wave output to the pin 48 (FOO) of IC802 ? No IC802 is faulty. Yes 1.5~2.5sec Check the PWB pattern between pin 16 of CNS602 and IC804. Is +6.2V applied to the pins 1 and 30 (VCC) of IC804 ? No Yes Is sawtooth wave obtained between pins 25 and 26 of IC804 ? No Yes Is +5V applied to the pin 2 (MUTE) of IC804 ? No Yes 1.5~2.5sec Check the PWB pattern between pin 2 of IC804 and pin 58 (CD STB) of IC701.
XL-60H/70H • HF error. Is output (tracking error signal) obtained at the pins 46 (TEI) and 47 (TEZI) of IC802 the CD TEST MODE "STEP 4" is changed to "STEP 5"? No Is output obtained at the pins 2 and No 5 of BI802/CNS802 Optical pickup failure. Yes Yes test mode "step 4" Check the periphery of IC801. Check the PWB pattern between pin 12. (TEO) of IC801 and pins 46 and 47 of IC802. Is it normal ? test mode "step 5" TEI TEZI IC801 is faulty.
XL-60H/70H • Track search failure Does the sled motor run in FF/REW state when the SERVO TEST MODE "STEP1" is set? No Check as stated in item "SLED MOTOR OPERATION FAILURE". Yes Is the following wave output to the pin 49 (TRO) of IC802 during track search in normal playback? No IC802 failure. Yes TRO Is the following wave output to the pins 12 (TEO) of IC801 during track search in normal playback? No Yes TEO TEI Check the PWB pattern between pin 49 (TRO) of IC802 and pin 18 of IC804.
XL-60H/70H FUNCTION TABLE OF IC IC401 VHiLC75342M-1: Function/Volume Equalizer (LC75342M) Pin No. Port Name Function 1 DI Serial data and clock input pin for control. 2 CE Chip enable pin. Data written into an internal latch in a timing of [H] -> [L]. Each analog switch is activated. Data transfer enabled at [H] level. 3 VSS Ground pin. 4 TEST Electronic volume control pin. To be set to the VSS potential. 5 LOUT Volume + equalizer output pin.
XL-60H/70H IC401 VHiLC75342M-1: Function/Volume Equalizer (LC75342M) TEST VSS CE 4 3 2 DI CL VDD Vref NC 1 30 29 27 28 LOUT 5 CONTROL CIRCUIT LBASS1 7 LTRE 8 RVref 25 RBASS2 24 RBASS1 CONTROL CIRCUIT LBASS2 6 LOGIC CIRCUIT CCB INTERFACE LVref 26 ROUT 23 RTRE 22 RIN LIN 9 21 RSEL0 LSEL0 10 11 12 13 14 15 16 17 18 19 20 L4 L3 L2 L1 NC NC R1 R2 R3 R4 Figure 44 BLOCK DIAGRAM OF IC – 44 –
XL-60H/70H IC701 RH-iX0026SJZZ: System Control Microcomputer (IX0026SJ) (1/2) Pin No. Terminal Name Input/Output 1-4 COM3-COM0 5-7 VLC3-VLC1 — LCD power supply terminal. 8 VDD — Microcomputer power supply +5V. Output Function LCD common output terminal. 9 OSC2 Output Oscillator ground terminal for main clock. f=8MHz 10 OSC1 Input Oscillator ground terminal for main clock. f=8MHz 11 VSS 12 XI Input Oscillator ground terminal for sub clock. f=32.
XL-60H/70H IC701 RH-iX0026SJZZ: System Control Microcomputer (IX0026SJ) (2/2) Pin No. Terminal Name Input/Output Function 54 SEG46 P63/A3 Output Electric JOG dial UP. 55 SEG45 P64/A4 Output Electric JOG dial DOWN. 56 SEG44 P65/A5 Output Electric CD lid OPEN. 57 SEG43 P66/A6 Output 58 SEG42 P67/A7 Input 59 SEG41 P70/A8 Output Reset signal output for TC9462F 60 SEG40 P71/A9 Output ON/OFF output terminal of CD servo control IC.
XL-60H/70H IC801 VHiTA2109F/-1:Servo Pre Amp. (TA2109F) Pin No.
XL-60H/70H IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F) (1/3) Pin No. Port Name Function Input/Output 1* TEST0 Input Test mode terminal. To be opened usually. 2* 3* /HSO /UHSO Output Output Playback speed mode flag output terminal. /UHSO /HSO Playback speed H H x1 speed playback H L x2 speed playback L H x4 speed playback L L — 4* EMPH Output Sub-code Q data emphasis flag output terminal. "H": Emphasis ON "L": Emphasis OFF The output polarity can be inverted by command.
XL-60H/70H IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F) (2/3) Pin No. Port Name Function Input/Output 39 AVDD — 40 RFCT Input RFRP signal center level input terminal. 41 RFZI Input RFRP zero cross input terminal. 42 RFIP Input RF ripple signal input terminal. 43 FEI Input Focus error signal input terminal. 44 SBAD Input Sub-beam addition signal input terminal. 45 TSIN Input Test input terminal. To be fixed to Vref usually. 46 TEI Input Tacking error input terminal.
XL-60H/70H IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F) (3/3) Function Input/Output Port Name Pin No. 83 DVDD — D/A converting section power terminal. 84 DVR — Reference voltage terminal. 85 LO Output L channel data forward rotation output terminal. 86 DVSL — 87* TEST1 Input L channel D/A converting section power terminal. Test mode terminal. To be opened usually. 88* TEST2 Input Test mode terminal. To be opened usually.
XL-60H/70H IC804 VHiLA6541D/-1: Focus/Tracking/Spin/Sled Driver (LA6541D) Pin No.
XL-60H/70H LCD701: RV-LX0007SJZZ LCD Display z1 z4 z2 r z3 q 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 PinNo com1 1 com1 2 com2 com3 PinNo com1 com2 com3 com4 22 h5 j5 l5 k5 23 g5 n5 m5 d5 24 a5 p5 f5 e5 com4 25 RDS b6 c6 ST com4 com2 3 com3 4 5 z1 b1 c1 z2 26 h6 j6 l6 k6 6 h1 j1 l1 k1 27 g6 n6 m6 d6 7 g1 n1 m1 d1 28 a6 p6 f6 e6 8 a1 p1 f1 e1 29 r b7 c7
XL-60H/70H PARTS GUIDE MODEL XL-60H XL-70H XL-60H/XL-70H Micro Component System consisting of XL-60H/ XL-70H (main unit) and CP-XL60H/CP-XL70H (speaker system). “HOW TO ORDER REPLACEMENT PARTS” To have your order filled promptly and correctly, please furnish the following information. 1. MODEL NUMBER 2. REF. No. 3. PART NO. 4. DESCRIPTION For U.S.A. only Contact your nearest SHARP Parts Distributor to order.
XL-60H/70H NO. PRICE RANK PARTS CODE DESCRIPTION NO. ZD601 ZD602 ZD681 ZD682 ZD701 XL-60H/70H INTEGRATED CIRCUITS IC101 IC102 VHIBA3126N/-1 VHIBA3311L/-1 J J IC201 IC302 IC303 VHIKIA4558P-1 VHILC72131/-1 VHILA1832S/-1 J J J IC401 VHILC75342M-1 J IC521 IC601 IC701 VHILC72723M-1 VHILA4451//-1 RH-IX0026SJZZ J J J IC702 IC801 IC802 IC804 VHITA7291S/-1 VHITA2109F/-1 VHITC9462F/-1 VHILA6541D/-1 J J J J IC805 VHITA7291S/-1 J AF Head Selector,BA3126N AK REC./P.B.Equalizer Amp.
XL-60H/70H NO.
XL-60H/70H NO. PARTS CODE C861 C862 C863 C871 C872 C887 C901 C902 C903 C904,905 VCKYPA1HB102K VCKYPA1HB222K VCKYTV1HB471K RC-GZA476AF1C VCKYTV1EB104K VCKYTV1HB272K VCKYTV1HB102K RC-GZA335AF1H RC-GZA107AF1E VCKYTV1HF223Z PRICE RANK DESCRIPTION J J J J J J J J J J AA AA AA AB AA AA AA AB AB AA 0.001 µF,50V 0.0022 µF,50V 470 pF,50V 47 µF,16V,Electrolytic 0.1 µF,25V 0.0027 µF,50V 0.001 µF,50V 3.3 µF,50V,Electrolytic 100 µF,25V,Electrolytic 0.
XL-60H/70H NO.
XL-60H/70H NO.
XL-60H/70H NO. PRICE RANK PARTS CODE DESCRIPTION NO.
XL-60H/70H XL-60H/70H A 307 B 701 306 304 306-2 701 C 306-1 704 306-3 302 D 702 301 303 E 703x2 NM802 F 305 G NM801 305x2 NSW801 PWB-C H 1 2 3 4 Figure 7 CD MECHANISM EXPLODED VIEW –7– 5 6
XL-60H/70H XL-60H/70H 613 214 212 210 206 615x2 613 217 A 204 613 205 PWB-A9 613x2 613 PWB-A6 220 216 B 216-2 BELT CONNECTION Motor(M901) 216-1 601 616x5 FF/REW Clutch 603x2 PWB-A10 255 601 FF/REW Belt PWB- 601 A10 CD MECHANISM Main Belt Flywheel PWB-A10x3 601x3 PWB-A3 PWB-A7 253 610x2 PWB-A4 PWBA8 254 C PWB-A2 LCD701 257 241 603 601x2 234 233 252 M701 246 232 243 608x2 244 609x3 608x2 250 613x2 609x3 604 x2 256 251 240 247 D 605 610x2 PWB-A5 208 209
XL-60H/70H CP-XL60H A TWEETER SP603(L-CH) SP604(R-CH) TWEETER SP603(L-CH) SP604(R-CH) BLACK RED WOOFER SP601(L-CH) SP602(R-CH) B BLACK WITH WHITE LINE BLACK WOOFER SP601(L-CH) SP602(R-CH) C 708 SP603(L-CH) SP604(R-CH) D 701 702 709x4 705 706 E 704 SP601(L-CH) SP602(R-CH) 703 F G 707x4 H 1 2 3 4 Figure 9 SPEAKER EXPLODED VIEW (1/2) –9– 5 6
XL-60H/70H CP-XL70H Capacitor (706) A TWEETER SP603(L-CH) SP604(R-CH) BK 711 B BK Black with White Line BK 712 Black with White Line WOOFER SP601(L-CH) SP602(R-CH) C 709 702 D 704x4 SP603(L-CH) SP604(R-CH) 703 706 708x4 E 710 SP601(L-CH) SP602(R-CH) F 701 TWEETER SP603(L-CH) SP604(R-CH) 706 Capacitor 3.
XL-60H/70H PACKING OF METHOD (FOR U.K. ONLY) XL-60H/70H CP-XL60H 1. AC Power Supply Cord 2. AM Loop Antenna 3. FM Antenna 4. Remote Control 5. Packing Add., Left/Right 6. Packing Case [XL-60H] 6. Packing Case [XL-70H] 7. Polyethylene Sheet, Unit 8. Polyethylene Sheet, AC Power Supply Cord 9. Polyethylene Bag, Accessories 10. Operation Manual 11. Feature Label [XL-60H] 11. Feature Label [XL-70H] 12. Quick Guide 13. Bar Code Label, Packing Case 14.
